Lines Matching +full:stop +full:- +full:mode

71 stop or restart
75 of signals that stop or start the group as a whole, along with
119 which generates the terminal stop signal
134 Orphaned process groups are immune to keyboard generated stop
190 returns -1 with
198 signal is to stop the
224 returns -1 with
238 full-duplex mode, so that data may arrive even while output is occurring.
260 whether the terminal device file is in canonical mode or noncanonical
261 mode.
271 This is useful for terminals that can operate in full-duplex mode.
275 canonical or noncanonical mode.
291 .Bl -enum -offset indent
301 If there is no data available, the read returns -1, with
306 When data is available depends on whether the input processing mode is
308 .Ss Canonical Mode Input Processing
309 In canonical mode input processing, terminal input is processed in units
313 character, an end-of-file
315 character, or an end-of-line
357 This un-delimited
378 .Ss Noncanonical Mode Input Processing
379 In noncanonical mode input processing, input bytes are not assembled into
414 serves as an inter-byte timer and is activated after
416 Since it is an inter-byte timer, it is reset
423 follows: as soon as one byte is received, the inter-byte timer is
427 bytes are received before the inter-byte timer expires
466 A program that uses this case to read record-based terminal
475 no longer represents an inter-byte
517 .Bl -tag -width indent
556 .Sx "Canonical Mode Input Processing" .
600 representing an end-of-file indication.
632 .It Dv STOP
646 .Dv STOP
658 .Dv STOP
689 .St -p1003.1
691 .Bl -tag -width indent
706 erased, and then the maximal sequence of non-whitespace
714 non-whitespace character is skipped in determining
766 is set to a non-zero value, the running thread's kernel stack is
806 file and test for end-of-file can terminate appropriately after a
820 to the terminal device returns -1, with
858 .Bl -tag -width IMAXBEL -offset indent -compact
882 /* any char will restart after stop */
886 /* assume input is UTF-8 encoded */
890 condition is defined as a sequence of zero-valued bits that continues for
892 The entire sequence of zero-valued
937 three-character sequence
943 is a two-character
1011 is set, start/stop output control is enabled.
1013 .Dv STOP
1027 .Dv STOP
1036 .Dv STOP
1041 is set, start/stop input control is enabled.
1043 .Dv STOP
1045 terminal device to stop transmitting data, as needed to prevent the input
1055 .Dv STOP
1077 .Bl -tag -width ONOEOT -offset indent -compact
1081 /* map NL to CR-NL (ala
1146 is set, the NL character is assumed to do the carriage-return function;
1157 .Bl -tag -width CRTSXIFLOW -offset indent -compact
1169 /* send 2 stop bits */
1214 is set, two stop bits are used, otherwise one stop bit.
1215 For example, at 110 baud, two stop bits are normally used.
1280 As a result, this flag is only useful on initial-state devices.
1295 .Bl -tag -width NOKERNINFO -offset indent -compact
1309 /* visual erase mode for hardcopy */
1333 /* stop background jobs from output */
1433 .Sx "Canonical Mode Input Processing" .
1448 .Sx "Noncanonical Mode Input Processing"
1474 is set, implementation-defined functions are recognized
1489 implementation-defined functions are not recognized, and the
1541 .Bl -column "Index Name" "Special Character" -offset indent -compact
1555 .It Dv VSTOP Ta STOP Ta \&^S
1558 .It Dv VMIN Ta --- Ta \&1
1559 .It Dv VTIME Ta --- Ta \&0