Lines Matching +full:hw +full:- +full:device +full:- +full:address

2 .\" SPDX-License-Identifier: BSD-3-Clause
4 .\" Copyright (c) 2019-2020, Intel Corporation
42 .Cd device iflib
43 .Cd device ice
48 .Cd hw.ice.enable_health_events
49 .Cd hw.ice.irdma
50 .Cd hw.ice.irdma_max_msix
51 .Cd hw.ice.debug.enable_tx_fc_filter
52 .Cd hw.ice.debug.enable_tx_lldp_filter
53 .Cd hw.ice.debug.ice_tx_balance_en
63 .Cd dev.ice.#.hw.mac.*
73 .Bl -bullet -compact
77 .Sx Dynamic Device Personalization
91 .Sx Link-Level Flow Control
113 .Sx Optics and auto-negotiation
115 .Sx PCI-Express Slot Bandwidth
155 For more information on configuring this device, see
163 .Ss Dynamic Device Personalization
164 The DDP package loads during device initialization.
169 If the driver is unable to load the DDP package, the device will enter Safe
190 even if more than one installed device uses the driver.
192 Only the first loaded PF per device can download a package for that device.
214 Remote Direct Memory Access, or RDMA, allows a network device to transfer data
236 To use RDMA monitoring, more MSI-X interrupts may need to be reserved.
241 .Bd -literal -offset indent
245 The number of extra MSI-X interrupt vectors may need to be adjusted.
248 .Bd -literal -offset indent
258 .Bd -literal -offset indent
282 .Bl -bullet -compact
284 Firmware-based LLDP Agent
286 Software-based LLDP Agent
289 In firmware-based mode, firmware intercepts all LLDP traffic and handles DCBX
299 In software-based mode, LLDP traffic is forwarded to the network stack and user
304 This mode requires the FW-based LLDP Agent to be disabled.
306 Firmware-based mode and software-based mode are controlled by the
312 Link-level flow control and priority flow control are mutually exclusive.
317 To enable/disable priority flow control in software-based DCBX mode:
318 .Bd -literal -offset indent
325 .Bd -literal -offset indent
333 .Bd -literal -offset indent
341 .Bd -literal -offset indent
347 driver supports setting DSCP-based Layer 3 Quality of Service (L3 QoS)
352 .Bd -literal -offset indent
359 For example, to map DSCPs 0-3 and DSCP 8 to DCB TCs 0-3 and 4, respectively:
360 .Bd -literal -offset indent
361 sysctl dev.ice.<interface #>.dscp2tc_map.0-7=0,1,2,3,0,0,0,0
362 sysctl dev.ice.<interface #>.dscp2tc_map.8-15=4,0,0,0,0,0,0,0
369 .Bd -literal -offset indent
373 L3 QoS mode is not available when FW-LLDP is enabled.
375 FW-LLDP cannot be enabled if L3 QoS mode is active.
377 Disable FW-LLDP before switching to L3 QoS mode.
381 section in this README for more information on disabling FW-LLDP.
383 Use sysctl to change FW-LLDP settings.
384 The FW-LLDP setting is per port and persists across boots.
386 To enable the FW-LLDP Agent:
387 .Bd -literal -offset indent
391 To disable the FW-LLDP Agebt:
392 .Bd -literal -offset indent
397 .Bd -literal -offset indent
405 attribute is set to disabled, the FW-LLDP Agent cannot be enabled from the
407 .Ss Link-Level Flow Control
423 .Bd -literal -offset indent
428 .Bd -literal -offset indent
470 .Bd -literal -offset indent
478 .Bd -literal -offset indent
483 .Bd -literal -offset indent
488 .Bd -literal -offset indent
489 sysctl -d dev.ice.<interface #>.requested_fec
494 To have the device change the speeds it will use in auto-negotiation or
496 .Bd -literal -offset indent
500 Supported speeds will vary by device.
501 Depending on the speeds the device supports, valid bits used in a speed mask
503 .Bd -literal -offset indent
504 0x0 - Auto
505 0x2 - 100 Mbps
506 0x4 - 1 Gbps
507 0x8 - 2.5 Gbps
508 0x10 - 5 Gbps
509 0x20 - 10 Gbps
510 0x80 - 25 Gbps
511 0x100 - 40 Gbps
512 0x200 - 50 Gbps
513 0x400 - 100 Gbps
514 0x800 - 200 Gbps
525 .Bd -literal -offset indent
538 .Bl -enum -compact
565 .Bl -tag -offset indent -compact -width "task_dispatch"
593 XLR (function-level resets; Bit 13)
601 Intel On-Chip System Fabric (Bit 17)
640 .Bl -item -offset indent -compact
655 .Bd -literal -offset indent
660 .Bd -literal -offset indent
671 setting tells the device to register the variable as soon as possible during
674 .Bd -literal -offset indent
682 .Bd -literal -offset indent
695 This debug dump contains a snapshot of the device and its existing hardware
699 stateless snapshot of the whole device.
702 human-readable.
705 Debug dump is per device, not per PF.
715 .Bd -literal -offset indent
724 .Bd -literal -offset indent
725 sysctl -d dev.ice.0.debug.dump.clusters
731 .Bl -bullet -compact
733 0 - Dump all clusters (only supported on Intel Ethernet E810 Series and
736 0x1 - Switch
738 0x2 - ACL
740 0x4 - Tx Scheduler
742 0x8 - Profile Configuration
744 0x20 - Link
746 0x80 - DCB
748 0x100 - L2P
750 0x400000 - Manageability Transactions (only supported on Intel Ethernet
755 .Bd -literal -offset indent
760 .Bd -literal -offset indent
769 .Bd -literal -offset indent
770 sysctl -b dev.ice.<interface #>.debug.dump.dump=1 > dump.bin
783 .Bd -literal -offset indent
793 .Bl -bullet
801 .Bd -literal -offset indent
805 NOTE: The contents of the registers are not human-readable.
816 setting for the device:
817 .Bl -bullet
824 Enable the Transmit Balancing device setting in UEFI HII.
828 configures the device accordingly.
834 This setting is device wide.
841 .Bd -literal -offset indent
849 Check to see if the system is mbuf-starved by running
853 .Bd -literal -offset indent
866 .Bd -literal -offset indent
879 .Bl -bullet
881 To change the behavior of the QSFP28 ports on E810-C adapters, use the Intel
882 .Sy Ethernet Port Configuration Tool - FreeBSD .
885 .Sy Non-Volatile Memory (NVM) Update Utility for Intel Ethernet Network Adapters E810 series - Free…
887 .Ss Optics and auto-negotiation
888 Modules based on 100GBASE-SR4,
890 do not support auto-negotiation per the IEEE specification.
892 auto-negotiation must be turned off on the link partner's switch ports.
896 that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications.
897 .Ss PCI-Express Slot Bandwidth
902 if a PCIe v4.0 or v3.0-capable adapter is placed into into a PCIe v2.x
907 .Bd -ragged -offset indent
908 PCI-Express bandwidth available for this device
910 Please move the device to a different PCI-e link
917 .Bl -bullet
919 Any 100Gbps-capable Intel(R) Ethernet 800 Series device: Install in a
922 A 200Gbps-capable Intel(R) Ethernet 830 Series device: Install in a
934 .Bl -bullet -compact
936 Intel Ethernet Controller E810-C
938 Intel Ethernet Controller E810-XXV
940 Intel Ethernet Connection E822-C
942 Intel Ethernet Connection E822-L
944 Intel Ethernet Connection E823-C
946 Intel Ethernet Connection E823-L
948 Intel Ethernet Connection E825-C
950 Intel Ethernet Connection E830-C
952 Intel Ethernet Connection E830-CC
954 Intel Ethernet Connection E830-L
956 Intel Ethernet Connection E830-XXV
958 Intel Ethernet Connection E835-C
960 Intel Ethernet Connection E835-CC
962 Intel Ethernet Connection E835-L
964 Intel Ethernet Connection E835-XXV
978 .Bl -bullet -compact
980 Intel 100G QSFP28 100GBASE-SR4   E100GQSFPSR28SRX
982 Intel 100G QSFP28 100GBASE-SR4   SPTMBP1PMCDF
984 Intel 100G QSFP28 100GBASE-CWDM4 SPTSBP3CLCCO
986 Intel 100G QSFP28 100GBASE-DR    SPTSLP2SLCDF
993 .Bl -bullet -compact
995 Intel 10G/25G SFP28 25GBASE-SR E25GSFP28SR
997 Intel     25G SFP28 25GBASE-SR E25GSFP28SRX (Extended Temp)
999 Intel     25G SFP28 25GBASE-LR E25GSFP28LRX (Extended Temp)
1006 .Bl -bullet -compact
1008 Intel 1G/10G SFP+ 10GBASE-SR E10GSFPSR
1010 Intel 1G/10G SFP+ 10GBASE-SR E10GSFPSRG1P5
1012 Intel 1G/10G SFP+ 10GBASE-SR E10GSFPSRG2P5
1014 Intel    10G SFP+ 10GBASE-SR E10GSFPSRX (Extended Temp)
1016 Intel 1G/10G SFP+ 10GBASE-LR E10GSFPLR
1026 .Bl -tag -width indent
1027 .It Va hw.ice.enable_health_events
1034 .It Va hw.ice.irdma
1039 .It Va hw.ice.rdma_max_msix
1040 Set the maximum number of per-device MSI-X vectors that are allocated for use
1045 .It Va hw.ice.debug.enable_tx_fc_filter
1051 .It Va hw.ice.debug.enable_tx_lldp_filter
1059 .It Va hw.ice.debug.ice_tx_balance_en
1060 Set to 1 to allow the driver to use the 5-layer Tx Scheduler tree topology if
1066 .Bl -tag -width indent
1069 This is expected to match the speed of the media type in-use displayed by
1081 .It Va dev.ice.#.hw.mac.*
1089 .Va hw.intr_storm_threshold
1095 .Bl -tag -width indent
1096 .It mac-addr Pq unicast-mac
1097 Set the Ethernet MAC address that the VF will use.
1098 If unspecified, the VF will use a randomly generated MAC address and
1099 .Dq allow-set-mac
1101 .It mac-anti-spoof Pq bool
1102 Prevent the VF from sending Ethernet frames with a source address
1105 .It allow-set-mac Pq bool
1106 Allow the VF to set its own Ethernet MAC address.
1108 .It allow-promisc Pq bool
1112 .It num-queues Pq uint16_t
1114 By default, this is set to the number of MSI-X vectors supported by the VF
1116 .It mirror-src-vsi Pq uint16_t
1118 other than -1.
1125 .Dq allow-promisc
1127 .It max-vlan-allowed Pq uint16_t
1133 .It max-mac-filters Pq uint16_t
1134 Specify maximum number of MAC address filters that the VF can use.
1135 Each allowed MAC address requires a hardware filter which are a finite
1138 The VF's default mac address does not count towards this limit.
1165 device driver first appeared in