Lines Matching +full:25 +full:a
23 .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
49 To load the driver as a module at boot time, place the following lines in
124 module and checks that it contains a valid DDP package file.
130 downloading a new driver or DDP package.
144 To overwrite a package, unload all PFs and then reload the driver with the
150 Only the first loaded PF per device can download a package for that device.
153 to a value larger than the default value of 1500.
167 Packet loss may have a greater impact on throughput when you use jumbo
169 If you observe a drop in performance after enabling jumbo frames, enabling
172 Remote Direct Memory Access, or RDMA, allows a network device to transfer data
187 For debugging/testing purposes, you can use sysctl to set up a mirroring
188 interface on a port.
225 Data Center Bridging (DCB) is a configuration Quality of Service
235 DCB is normally configured on the network using the DCBX protocol (802.1Qaz), a
250 DCBX mode, receiving DCB settings from the link partner (typically a
253 For information on configuring DCBX parameters on a switch, please consult the
257 space, where a software agent can handle it.
288 For example, to set all TCs to a minimum bandwidth of 10% and TC 7 to 30%,
294 To set the User Priority (UP) to a TC mapping for a port, separate the values
315 To map a DSCP value to a traffic class, separate the values by commas.
369 buffer crosses a predefined threshold.
371 specified in the firmware when a pause frame is received.
375 Use sysctl to change the flow control settings for a single interface without
415 provide a stable link without FEC.
455 Depending on the speeds your device supports, valid bits used in a speed mask
464 0x80 \- 25 Gbps
491 At a high level, to capture a firmware log:
507 NOTE: Firmware logs are generated in a binary format and must be decoded by
571 Task Dispatcher (Bit 25)
607 To set the desired verbosity level for a module, use the following sysctl
634 To view the firmware logs and redirect them to a file, use the following
640 NOTE: Logging a large number of modules or too high of a verbosity level will
646 of events and then write the results to a single dump file, for debugging
649 This debug dump contains a snapshot of the device and its existing hardware
652 Debug dump captures the current state of the specified cluster(s) and is a
661 Debug dump writes all information to a single file.
663 To generate a debug dump file in
667 Specify the cluster(s) to include in the dump file, using a bitmask and the
720 If you don't specify a cluster, the driver will dump all clusters to a
737 mask before a subsequent debug dump and then do the dump:
764 Some Intel(R) Ethernet 800 Series devices allow you to enable a transmit
801 may have a low number of network memory buffers (mbufs) by default.
868 driver supports 25Gb and 10Gb Ethernet adapters with these SFP28 modules:
872 Intel\(rg 10G/25G SFP28 25GBASE-SR E25GSFP28SR
874 Intel\(rg 25G SFP28 25GBASE-SR E25GSFP28SRX (Extended Temp)
876 Intel\(rg 25G SFP28 25GBASE-LR E25GSFP28LRX (Extended Temp)
911 In addition, if you put a PCIe v4.0 or v3.0\-capable adapter into a PCIe v2.x
919 Please move the device to a different PCI\-e link with more lanes and/or
923 If this error occurs, moving your adapter to a true PCIe x8 or x16 slot will
928 Any 100Gbps\-capable Intel(R) Ethernet 800 Series device: Install in a
931 A 200Gbps\-capable Intel(R) Ethernet 830 Series device: Install in a
947 If enabled, when the driver receives a firmware health event message, it will
948 print out a description of the event to the kernel message buffer and if
984 This is a display of the current link speed of the interface.
1003 a storm condition in the kernel.
1014 If unspecified, the VF will use a randomly generated MAC address and
1018 Prevent the VF from sending Ethernet frames with a source address
1033 Specify which VSI the VF will mirror traffic from by setting this to a value
1045 Receiving traffic on a VLAN requires a hardware filter which are a finite
1046 resource; this is used to prevent a VF from starving other VFs or the PF of
1051 Each allowed MAC address requires a hardware filter which are a finite
1052 resource; this is used to prevent a VF from starving other VFs or the PF of
1070 If an issue is identified with this driver with a supported adapter,