Lines Matching +full:dma +full:- +full:default

1 .\" Copyright (c) 2006-2014 QLogic Corporation
35 .Bd -ragged -offset indent
43 .Bd -literal -offset indent
53 Ethernet controllers which support a TCP Offload Engine (TOE), Remote DMA (RDMA),
62 .Bl -item -offset indent -compact
72 10/100/1000Mbps operation in full-duplex mode
74 10/100Mbps operation in half-duplex mode
80 .Bl -tag -width ".Cm 10baseT/UTP"
92 .Cm full-duplex
94 .Cm half-duplex
102 .Cm full-duplex
104 .Cm half-duplex
109 .Cm full-duplex
114 .Cm full-duplex
119 .Cm full-duplex
126 .Bl -tag -width ".Cm full-duplex"
127 .It Cm full-duplex
129 .It Cm half-duplex
142 .Bl -bullet -compact
144 QLogic NetXtreme II BCM5706 1000Base-SX
146 QLogic NetXtreme II BCM5706 1000Base-T
148 QLogic NetXtreme II BCM5708 1000Base-SX
150 QLogic NetXtreme II BCM5708 1000Base-T
152 QLogic NetXtreme II BCM5709 1000Base-SX
154 QLogic NetXtreme II BCM5709 1000Base-T
156 QLogic NetXtreme II BCM5716 1000Base-T
188 HP NC382m DP 1GbE Multifunction BL-c Adapter
196 .Bl -tag -width indent
199 Useful for debugging (default 0).
201 Enable/Disable MSI support (default 1).
203 Enable/Disable TSO support (default 1).
205 Enable/Disable strict RX frame size checking (default 0).
207 Enable/Disable frame header/payload splitting (default 1).
211 1, 2, 4 or 8 (default 2).
216 1, 2, 4 or 8 (default 2).
220 Values from 0-100 are valid.
227 Values from 0-100 are valid.
228 Valid values are in the range from 0-100.
229 A value of 0 disables this status block update (default 18).
233 Values from 0-256 are valid.
235 Cannot be set to 0 if hw.bce.rx_ticks is also 0 (default 6).
239 Values from 0-256 are valid.
240 A value of 0 disables this status block update (default 6).
244 Values from 0-100 are valid.
251 Values from 0-100 are valid.
252 A value of 0 disables this status block update (default 80).
256 Values from 0-100 are valid.
258 Cannot be set to 0 if hw.bce.tx_ticks is also 0 (default 20).
262 Values from 0-100 are valid.
263 A value of 0 disables this status block update (default 20).
266 .Bl -diag
277 .It "bce%d: DMA resource allocation failed!"
278 The driver could not allocate DMA memory to setup the controllers
301 .It "bce%d: DMA mapping error!"
302 The driver was unable to map memory into DMA addressable space required
304 .It "bce%d: Could not allocate parent DMA tag!"
305 The driver could not allocate a PCI compatible DMA tag.
306 .It "bce%d: Could not allocate status block DMA tag!"
307 The driver could not allocate a DMA tag for the controller's
309 .It "bce%d: Could not allocate status block DMA memory!"
310 The driver could not allocate DMA addressable memory for the controller's
312 .It "bce%d: Could not map status block DMA memory!"
313 The driver could not map the status block memory into the controller's DMA
315 .It "bce%d: Could not allocate statistics block DMA tag!"
316 The driver could not allocate a DMA tag for the controller's
318 .It "bce%d: Could not allocate statistics block DMA memory!"
319 The driver could not allocate DMA addressable memory for the controller's
321 .It "bce%d: Could not map statistics block DMA memory!"
322 The driver could not map the statistics block memory into the controller's DMA
324 .It "bce%d: Could not allocate TX descriptor chain DMA tag!"
325 The driver could not allocate a DMA tag for the controller's
327 .It "bce%d: Could not allocate TX descriptor chain DMA memory!"
328 The driver could not allocate DMA addressable memory for the controller's
330 .It "bce%d: Could not map TX descriptor chain DMA memory!"
331 The driver could not map the TX descriptor chain memory into the controller's DMA
333 .It "bce%d: Could not allocate TX mbuf DMA tag!"
334 The driver could not allocate a DMA tag for the controller's
336 .It "bce%d: Unable to create TX mbuf DMA map!"
337 The driver could not map the TX mbuf memory into the controller's DMA
339 .It "bce%d: Could not allocate RX descriptor chain DMA tag!"
340 The driver could not allocate a DMA tag for the controller's
343 The driver could not allocate DMA addressable memory for the controller's
345 .It "bce%d: Could not map RX descriptor chain DMA memory!"
346 The driver could not map the RX descriptor chain memory into the controller's DMA
348 .It "bce%d: Could not allocate RX mbuf DMA tag!"
349 The driver could not allocate a DMA tag for the controller's
351 .It "bce%d: Unable to create RX mbuf DMA map!"
352 The driver could not map the RX mbuf memory into the controller's DMA
371 The driver could not map a RX mbuf into DMA addressable memory.
390 The driver could not map a TX mbuf into DMA addressable memory.
411 or by E-mail at