Lines Matching full:specify

404 Specify a device name and unit number combination, like "da5" or "cd3".
406 Specify a bus number and target id.
412 Specify the bus, target and lun for a device.
454 Specify the device type to operate on, e.g.\& "da", "cd".
471 Specify the device unit number, e.g.\& "1", "5".
512 The user can specify that only certain types of
540 Specify the type of report to request from the target:
628 may specify a scan of all buses, a single bus, or a lun.
664 Specify the requested format of the defect list.
717 Specify the starting offset into the defect list.
788 This allows the user to specify the page control field.
807 argument to specify SCSI CDB or the
809 argument to specify ATA Command Block registers values.
816 SCSI device in question, you MUST specify either
860 argument to specify the SMP request to be sent, and the
862 argument to specify the format of the SMP response.
912 argument is required to specify the PHY to operate on.
915 Specify the PHY to operate on.
923 Specify a PHY control operation.
932 It is not necessary to specify this argument.
957 argument to specify the device name.
960 Specify the attached device name.
1204 Specify the bus width to negotiate with a device.
1207 The only useful values to specify are 8, 16, and 32
1241 Users should specify a
1323 Specify the sanitize operation to perform.
1827 Specify the service action for the PERSISTENT RESERVE IN command.
1841 Specify the service action for the PERSISTENT RESERVE OUT command.
1850 To register a key, specify the requested key as the Service Action
1852 To unregister a key, specify the previously registered key as the
1854 To change a key, specify the old key as the Reservation Key and the new
1897 Specify a Transport ID.
1978 Specify the Reservation Key.
1983 Specify the Service Action Reservation Key.
1992 Specify the scope of the reservation.
1995 If the desired scope isn't available by name, you may specify the number.
2006 Specify the Relative Target Port.
2012 You must also specify at least one Transport ID with
2015 If you specify a Transport ID, this option is automatically set.
2016 It is an error to specify this option for any service action other than
2019 Specify the reservation type.
2021 If the desired reservation type isn't available by name, you may specify
2057 Specify that the target should unregister the initiator that sent
2082 Specify the READ ATTRIBUTE service action.
2102 Specify an attribute to write to the MAM.
2105 Specify the attribute number to display.
2114 Specify the element address.
2119 Specify the output format for the attribute values (attr_val) display as a
2126 The text options are mutually exclusive; if you specify more than one, you
2163 Specify the partition.
2167 Specify the starting attribute number.
2171 Specify the element type.
2183 Specify the number of the logical volume to operate on.
2208 For commands that support a service action, specify the service action to
2294 Specify the zone subcommand:
2299 Specify report options with
2303 Specify the starting LBA with
2321 Specify the starting LBA.
2328 For the Report Zones command, specify a subset of zones to report.
2362 Specify a printing option for Report Zones:
2408 Specify the epc subcommand
2414 Specify the source for the restored power settings, either
2421 This only makes sense to specify when restoring from defaults.
2427 Specify the power condition: Idle_a, Idle_b, Idle_c, Standby_y, Standby_z.
2430 Specify delayed entry to the power condition.
2462 Specify the timer in seconds.
2463 The user may specify a timer as a floating point number with a maximum
2467 Specify the power condition: Idle_a, Idle_b, Idle_c, Standby_y, Standby_z.
2492 Specify the power condition: Idle_a, Idle_b, Idle_c, Standby_y, Standby_z.
2504 Specify the EPC power source.
2507 Specify the power source, either
2557 Specify the strftime format string, as documented in strftime(3), to be used
2578 Specify the strptime format string, as documented in strptime(3).
2643 Specify the desired capacity point for the drive.
2655 Specify the physical element to remove from service.
2670 variable allows the user to specify an alternate mode page format file.
2707 Specify a retry count of 4, and a timeout of 50 seconds.
3037 to specify generic