Lines Matching +full:0 +full:x12345678

410 The lun defaults to 0.
413 (e.g.\& 1:2:0)
493 Send the SCSI test unit ready (0x00) command to the given device.
498 Send a SCSI REQUEST SENSE command (0x03) to a device.
507 Send a SCSI inquiry command (0x12) to a device.
527 Send an ATA identify command (0xec) to a device.
529 Send the SCSI REPORT LUNS (0xA0) command to the given device.
611 Send the SCSI Start/Stop Unit (0x1B) command to the given device with the
614 Send the SCSI Start/Stop Unit (0x1B) command to the given device with the
617 Send the SCSI Start/Stop Unit (0x1B) command to the given device with the
620 Send the SCSI Start/Stop Unit (0x1B) command to the given device with the
657 READ DEFECT DATA (10) command (0x37) or the
659 READ DEFECT DATA (12) command (0xB7) to the given device, and
736 Some drives will report 0 defects if neither the primary or grown defect
791 .It 0
921 request length is set to a value other than 0.
971 .It 0x0
973 .It 0x8
975 .It 0x9
977 .It 0xa
1418 Value 0 disables timer.
1424 Value 0 disables timer.
1445 Update or report security settings, using an ATA identify command (0xec).
1452 .Bl -tag -width 0n
1574 .Bl -tag -width 0n
1642 .Bl -tag -width 0n
1915 .Dl sas,0x1234567812345678
1922 .Dl fcp,0x1234567812345678
1936 .Dl sbp,0x1234567812345678
1941 The port identifier must be exactly 32 or 34 (if the leading 0x is
1946 .Dl srp,0x12345678123456781234567812345678
1956 .Dl iqn.2012-06.com.example:target0,i,0x123
1963 The bus must be in the range of 0 to 255 inclusive and the device must be
1964 in the range of 0 to 31 inclusive.
1965 The function must be in the range of 0 to 7 inclusive if the standard form
1966 is used, and in the range of 0 to 255 inclusive if the alternate form is
1981 The value must be between 0 and 2^64 - 1, inclusive.
1986 The value must be between 0 and 2^64 - 1, inclusive.
1998 LUN scope (0x00).
2001 Extent scope (0x01).
2003 Element scope (0x02).
2534 Power Conditions log (Log Address 0x08).
2721 camcontrol cmd -n cd -u 1 -v -c "3C 00 00 00 00 00 00 00 0e 00" \e
2722 	-i 0xe "s1 i3 i1 i1 i1 i1 i1 i1 i1 i1 i1 i1"
2725 Issue a READ BUFFER command (0x3C) to cd1.
2731 camcontrol cmd -n cd -u 1 -v -c "3B 00 00 00 00 00 00 00 0e 00" \e
2735 Issue a WRITE BUFFER (0x3B) command to cd1.
2756 .Dl camcontrol rescan 0
2758 Rescan SCSI bus 0 for devices that have been added, removed or changed.
2760 .Dl camcontrol rescan 0:1:0
2762 Rescan SCSI bus 0, target 1, lun 0 to see if it has been added, removed, or
2781 camcontrol smpcmd ses0 -v -r 4 "40 0 00 0" -R 1020 "s9 i1"
2842 camcontrol persist da0 -v -o register -a -K 0x12345678
2845 This will register the persistent reservation key 0x12345678 with da0,
2849 camcontrol persist da0 -v -o reserve -s lun -k 0x12345678 -T ex_ac
2863 camcontrol persist da0 -v -o release -k 0x12345678 -T ex_ac
2868 The Reservation Key for this registration is 0x12345678.
2871 camcontrol persist da0 -v -o register -K 0x12345678 -S \e
2872 	-I sas,0x1234567812345678 -I sas,0x8765432187654321
2875 This will register the key 0x12345678 with da0, specifying that it applies
2876 to the SAS initiators with SAS addresses 0x1234567812345678 and
2879 camcontrol persist da0 -v -o register_move -k 0x87654321 \e
2880 	-K 0x12345678 -U -p -R 2 -I fcp,0x1234567812345678
2884 Registration Key is 0x87654321, to the Fibre Channel initiator with the
2885 Fiber Channel World Wide Node Name 0x1234567812345678.
2886 A new registration key, 0x12345678, will be registered for the initiator
2887 with the Fibre Channel World Wide Node Name 0x1234567812345678, and the
2921 camcontrol zone da0 -v -c rwp -l 0x2c80000
2925 that starts at LBA 0x2c80000 and display any
2970 Display the ATA Power Conditions log (Log Address 0x08) for
3021 camcontrol cmd -n da -u 1 -c "00 00 00 00 00 v" 0x00 -v
3031 (0x00),