Lines Matching refs:para

35     <para>wpa_cli is a text-based frontend program for interacting
38     input.</para>
40     <para>wpa_cli can show the current authentication status, selected
50     response.</para>
52     <para>The control interface of wpa_supplicant can be configured to
55     normal user account.</para>
57     <para>wpa_cli supports two modes: interactive and command
60     messages (event messages, username/password requests).</para>
62     <para>Interactive mode is started when wpa_cli is executed without
65     commands are entered as command line arguments for wpa_cli.</para>
70    <para>When wpa_supplicant need authentication parameters, like
79    authentication server.</para>
81     <para>The reply to these requests can be given with
92     card -based authentication.</para>
94     <para>Example request for password and a matching reply:</para>
101     <para>Example request for generic token card challenge-response:</para>
115 	<listitem><para>Change the path where control sockets should
116 	be found.</para></listitem>
122 	<listitem><para>Connect to the global control socket at the
124 	socket.</para></listitem>
130         <listitem><para>Specify the interface that is being
132 	a control socket in the socket path.</para></listitem>
137 	<listitem><para>Help.  Show a usage message.</para></listitem>
143 	<listitem><para>Show version information.</para></listitem>
149 	<listitem><para>Run as a daemon in the background.</para></listitem>
155 	<listitem><para>Run in daemon mode executing the action file
160 	the interface.</para>
162 	<para>Additionally, three environmental variables are available to
167 	</para></listitem>
173 	<listitem><para>Set the location of the PID
174 	file.</para></listitem>
180 	<listitem><para>Set the interval (in seconds) at which
181 	wpa_cli pings the supplicant.</para></listitem>
187 	<listitem><para>Run a command.  The available commands are
188 	listed in the next section.</para></listitem>
195     <para>The following commands are available:</para>
201 	  <para>get current WPA/EAPOL/EAP status</para>
208 	  <para>get MIB variables (dot1x, dot11)</para>
215 	  <para>show this usage help</para>
222 	  <para>show interfaces/select interface</para>
229 	  <para>change debug level</para>
236 	  <para>show full wpa_cli license</para>
243 	  <para>IEEE 802.1X EAPOL state machine logoff</para>
250 	  <para>IEEE 802.1X EAPOL state machine logon</para>
257 	  <para>set variables (shows list of variables when run without arguments)</para>
263 	  <para>show PMKSA cache</para>
269 	  <para>force reassociation</para>
275 	  <para>force wpa_supplicant to re-read its configuration file</para>
282 	  <para>force preauthentication</para>
289 	  <para>configure identity for an SSID</para>
296 	  <para>configure password for an SSID</para>
303 	  <para>configure pin for an SSID</para>
310 	  <para>configure one-time-password for an SSID</para>
317 	  <para>set preferred BSSID for an SSID</para>
324 	  <para>list configured networks</para>
331 	  <para>terminate <command>wpa_supplicant</command></para>
337 	<listitem><para>exit wpa_cli</para></listitem>
343     <para>
348     </para>
352     <para>wpa_supplicant is copyright (c) 2003-2022,
355     All Rights Reserved.</para>
357     <para>This program is licensed under the BSD license (the one with
358     advertisement clause removed).</para>