Lines Matching full:network
22 The core Interworking functionality (network selection, GAS/ANQP) were
27 wpa_supplicant network selection
32 network blocks (e.g., per-SSID parameters). When requested to perform
33 network selection, wpa_supplicant picks the highest priority enabled
34 network block or credential. If a credential is picked (based on ANQP
35 information from APs), a temporary network block is created
36 automatically for the matching network. This temporary network block is
37 used similarly to the network blocks that can be configured by the user,
42 By default, wpa_supplicant is not using automatic network selection
44 can be changed with the auto_interworking=1 parameter to perform network
45 selection automatically whenever trying to find a network for connection
46 and none of the enabled network blocks match with the scan results. This
48 will internally determine which network or credential is going to be
87 # Access Network Type
89 # specified Access Network Type (0..15; with 15 indicating wildcard match).
90 # This value controls the Access Network Type value in Probe Request frames.
93 # Automatic network selection behavior
94 # 0 = do not automatically go through Interworking network selection
96 # 1 = perform Interworking network selection if one or more
98 # matching network block
102 Credentials can be pre-configured for automatic network selection:
106 # Each credential used for automatic network selection is configured as a set
117 # (and similarly in struct wpa_ssid for network blocks) to change the
119 # network (based on either an enabled network block or a credential)
126 # username: Username for Interworking network selection
128 # password: Password for Interworking network selection
130 # ca_cert: CA certificate for Interworking network selection
206 # parameter. When using Home OIs to match the network, the EAP parameters
226 # Consortium to match the network, the EAP parameters need to be
258 # matching with the network. Multiple entries can be used to specify more
293 # This value is used as the maximum channel utilization for network
301 # a roaming network shall support (include explicitly in Connection
304 # network connection. This policy is not used in home networks.
414 Add a WPA2-Enterprise network:
436 Add an open network:
454 Interworking network selection can be started with interworking_select
455 command. This instructs wpa_supplicant to run a network scan and iterate
469 INTERWORKING-AP event messages indicate the APs that support network
471 credential. interworking_connect command can be used to select a network
478 <3>SME: Trying to authenticate with 02:00:00:00:01:00 (SSID='Example Network' freq=2412 MHz)
479 <3>Trying to associate with 02:00:00:00:01:00 (SSID='Example Network' freq=2412 MHz)
489 wpa_supplicant creates a temporary network block for the selected
490 network based on the configured credential and ANQP information from the
494 network id / ssid / bssid / flags
495 0 Example Network any [CURRENT]
502 Alternatively to using an external program to select the network,
504 to select which network to use based on configured priorities:
519 <3>SME: Trying to authenticate with 02:00:00:00:01:00 (SSID='Example Network' freq=2412 MHz)
520 <3>Trying to associate with 02:00:00:00:01:00 (SSID='Example Network' freq=2412 MHz)
534 ssid=Example Network
574 02:00:00:00:01:00 2412 -30 [WPA2-EAP-CCMP][ESS][HS20] Example Network
592 ssid=Example Network
624 Following parameters can be used to create a network profile for
630 network={
643 Hotspot 2.0 connection with external network selection
647 network selection, following configuration and network profile
648 parameters can be used to configure a temporary network profile for a
656 network={