Lines Matching +full:65 +full:mhz
448 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
1091 * (CU) of each 20 MHz sub-channel of the entire connected channel using
1285 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65,
1584 /* Frequency in MHz, various uses. Unsigned 32 bit value */
1851 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
1934 * channel width (in MHz).
1947 * 20 MHz, 40 MHz, and 80 MHz channels. The value is the center frequency index
1948 * of the primary 80 MHz segment for 160 MHz and 80+80 MHz channels.
1958 * ACS operation. The value is zero for 20 MHz, 40 MHz, and 80 MHz channels.
1959 * The value is the index of the channel center frequency for 160 MHz channels
1960 * and the center frequency index of the secondary 80 MHz segment for 80+80 MHz
1971 * center frequencies in MHz (u32).
1979 * Used with event to notify the primary channel center frequency (MHz) selected
1985 * Used with event to notify the secondary channel center frequency (MHz)
1992 * Used with event to notify the VHT segment 0 center channel frequency (MHz)
1999 * Used with event to notify the VHT segment 1 center channel frequency (MHz)
2350 /* An array of 32-unsigned values; values are frequency (MHz); sent
2355 * attribute. Each element contains frequency (MHz), weight, and flag
2372 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */
2599 * with frequencies to be scanned (in MHz)
2873 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for
2875 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
2876 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
2877 * 10 MHz channel width, the station will not connect to a BSS using 20
2878 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
3064 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MSDU_AGGREGATION = 65,
3330 * list of allowed 20 MHz channel center frequencies in MHz for AP
3709 * Channel center frequency (MHz) on which the access point should restart.
3994 * Channel center frequency (MHz) hint for ACS operation, if a valid center
4369 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
5015 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
5107 /* Unsigned 32 bit value. Primary 20 MHz channel. This is used to
5115 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */
5117 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */
5133 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65,
5643 * List of frequencies in MHz to be considered for a roam scan.
6700 /* Unsigned 32-bit value; channel frequency in MHz */
7134 /* frequency in MHz (u32) */
7156 * Segment 0 in MHz (u32).
7158 * For 20/40/80 MHz bandwidth, this indicates the channel center
7159 * frequency index for the 20/40/80 MHz operating channel.
7160 * For 160 MHz bandwidth, this indicates the channel center
7161 * frequency of the primary 80 MHz channel.
7162 * For 320 MHz bandwidth, indicates the channel center frequency
7163 * of the primary 160 MHz channel.
7172 * VHT segment 0 in MHz (u32) and the attribute is mandatory.
7193 * Segment 1 in MHz (u32).
7195 * For 20/40/80 MHz bandwidth, this is set to 0.
7196 * For 160 MHz bandwidth, indicates the channel center frequency of the
7197 * 160 MHz channel.
7198 * For 320 MHz bandwidth, indicates the channel center frequency of the
7199 * 320 MHz channel.
7208 * VHT segment 1 in MHz (u32) and the attribute is mandatory.
7244 * This indicates the overlapping 320 MHz center frequency in MHz
7246 * 320 MHz channel bonding.
7249 * For 6 GHz, channel frequency 6115 MHz (channel number 33) segment 0
7250 * center frequency (primary 160 MHz) is 6185 MHz and there can be two
7251 * possible segment 2 frequencies for this (320 MHz center
7254 * 1) Center frequency 6105 MHz (channel 31): 320 MHz channel bonding
7255 * from frequency 5945 MHz - 6265 MHz
7256 * 2) Center frequency 6265 MHz (channel 63): 320 MHz channel bonding
7257 * from frequency 6105 MHz - 6425 MHz
7261 * return 6185 MHz.
7263 * return 6105 MHz.
7265 * will return 6265 MHz.
7315 * Units for PSD - dBm/MHz
7339 /* Channel frequency (u32) in MHz */
7461 * Secondary channel number, required only for 160 and 80+80 MHz bandwidths.
7495 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY in MHz (u32),
7496 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY in MHz (u32),
7497 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 in MHz (u32),
7498 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 in MHz (u32),
7504 * Primary channel frequency in MHz
7509 * Secondary channel frequency in MHz used for HT 40 MHz channels.
7514 * VHT seg0 channel frequency in MHz
7519 * VHT seg1 channel frequency in MHz
7551 /* Secondary channel (u8) used for HT 40 MHz channels */
7870 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
7977 * Center frequency (in MHz) of the span of interest or
7978 * for convenience, center frequency (in MHz) of any channel
7979 * in the span of interest. For 80+80 MHz agile spectral scan
7980 * request it represents center frequency (in MHz) of the primary
7981 * 80 MHz span or for convenience, center frequency (in MHz) of any
7982 * channel in the primary 80 MHz span. If agile spectral scan is
8019 * requests in 80+80 MHz mode. It represents center frequency (in
8020 * MHz) of the secondary 80 MHz span or for convenience, center
8021 * frequency (in MHz) of any channel in the secondary 80 MHz span.
8136 * for 20/40/80 MHz modes.
8140 * for 160 MHz mode.
8144 * for 80+80 MHz mode.
8147 /* Number of spectral detectors used for scan in 20 MHz.
8151 /* Number of spectral detectors used for scan in 40 MHz.
8155 /* Number of spectral detectors used for scan in 80 MHz.
8159 /* Number of spectral detectors used for scan in 160 MHz.
8163 /* Number of spectral detectors used for scan in 80+80 MHz.
8168 * for 320 MHz mode.
8171 /* Number of spectral detectors used for scan in 320 MHz.
8556 /* Primary channel center frequency (u32) in MHz */
8631 /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
8825 /* Unsigned 32-bit value; channel frequency in MHz */
8885 * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
9425 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7
9426 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9
9427 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11
9428 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7
9429 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9
9430 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11
9431 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7
9432 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9
9433 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11
9520 * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz
9521 * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz
9522 * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz
9523 * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz
9627 * supports in reception for PPDU bandwidths less than or equal to 80 MHz
9655 * STA supports in reception for PPDU bandwidths less than or equal to 80 MHz.
9658 * 320 MHz operating channel width supported by the EHT STA for both reception
9665 * to 80 MHz.
10240 * can receive in an EHT sounding NDP for <= 80 MHz bandwidth.
10248 * can receive in an EHT sounding NDP for 160 MHz bandwidth.
10256 * can receive in an EHT sounding NDP for 320 MHz bandwidth.
10285 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_EHT_MCS = 65,
10622 /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz
10627 /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz
11759 QCA_ZB_HIGH = 65,
11791 * | 1 | 34 | 32 | 65 |
11860 * | 0xff | 0xff | 0xff | 65 |
12163 /* Used by the driver to encapsulate the frequency in MHz on which
12343 * Starting center frequency in MHz.
12346 * Ending center frequency in MHz.
12873 * frequencies in MHz (u32) the station has learnt during the last connection
13184 * OCI frequency (in MHz) to override in the specified frame type.
13491 * channel in MHz.
13495 * channel in MHz. This attribute is required when reporting 40 MHz, 80 MHz,
13496 * 160 MHz, and 320 MHz channels.
13500 * 80+80 channel in MHz. This attribute is required only when
13579 * 8 entries in order to save CAC result for a 160 MHz channel.
13581 * Channel frequency in MHz.
13648 * Channel frequency in MHz. This is present only in an event.
13802 * channel in MHz for each roam scan channel.
14470 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ: u32, frequency in MHz
14546 * u32 values. List of frequencies in MHz considered for a roam scan.
15775 * range in MHz.
15779 * in MHz.
15786 * The PSD power info (dBm/MHz) from user space should be multiplied
15790 * PSD power value: 10.21 dBm/MHz
17014 * For example: Negotiated maximum bandwidth is 160 MHz and the new maximum
17015 * bandwidth configured is 80 MHz, now the driver limits the maximum bandwidth
17016 * to 80 MHz only in the Tx path.
17022 * For example: Negotiated maximum bandwidth is 40 MHz and the new maximum
17023 * bandwidth configured is 20 MHz, now the driver indicates the change in
17024 * maximum allowed bandwidth to the AP and limits the bandwidth to 20 MHz in the
17025 * Tx path but keeps the phymode bandwidth as 40 MHz. This will avoid
17026 * interoperability issues with APs which still use 40 MHz for sending the
17027 * frames though it received maximum allowed bandwidth indication as 20 MHz
17041 * frequency (MHz): If PSD power, carries one 20 MHz sub-channel center
17042 * frequency. If non PSD power, carries either 20 MHz bandwidth's center
17043 * channel frequency or 40 MHz bandwidth's center channel frequency
17044 * (or 80/160 MHz bandwidth's center channel frequency).
17086 * If PSD power, each power level describes each 20 MHz subchannel PSD