Lines Matching +full:page +full:- +full:mode +full:- +full:read +full:- +full:delay
1 \input texinfo @c -*-texinfo-*-
24 @c @page
52 @comment node-name, next, previous, up
56 It uses the standard NTP mode 6 control message formats defined in
59 The description on this page is for the NTPv4 variables.
61 …eractive mode or controlled using command line arguments. Requests to read and write arbitrary va…
63 …by default. If no request options are given, @code{ntpq} will attempt to read commands from the s…
65 @code{ntpq} uses NTP mode 6 packets to communicate with the NTP server, and hence can be used to qu…
67 … name is expected, a @code{-4} qualifier preceding the host name forces DNS resolution to the IPv4…
69 For examples and usage, see the @url{debug.html, NTP Debugging Techniques} page.
71 @include invoke-ntpq.texi
74 @comment node-name, next, previous, up
81 @tab @code{-c}
85 @tab @code{-f}
93 @tab @code{-p}
97 @tab @code{-l}
105 @tab @code{-s}
109 @tab @code{-k}
114 @comment node-name, next, previous, up
117 …d entirely within the @code{ntpq} program itself and do not result in NTP mode-6 requests being se…
130 and can be omitted in read requests.
137 the list should be comma-separated and not contain white space.
148 @item @anchor{delay} @code{delay @kbd{milliseconds}}
149 …on. This is used to enable (unreliable) server reconfiguration over long delay network paths or b…
159 unless modified using the command line @code{-n} switch.
176 Note that mode-6 control messages (and modes, for that matter)
198 @comment node-name, next, previous, up
204 Most control commands send a single mode-6 message to the server
256 as a run-time configuration command in the same format
261 @item @anchor{config-from-file} config-from-file @kbd{filename}
263 run-time configuration commands in the same format as the configuration file.
335 Packet mode.
369 @code{[tally]remote refid st t when pool reach delay offset jitter}
375 single-character code indicating current value of the @code{select} field
412 @item @code{delay}
414 roundtrip delay
438 frequency values in parts-per-million (PPM).
445 given with @code{:config} or @code{config-from-file},
452 @code{saveconfig ntp-%Y%m%d-%H%M%S.conf}.
473 @comment node-name, next, previous, up
482 @url{decode.html, Event Messages and Status Words} page.
483 The page also includes a list of system and peer messages,
489 The original purpose was for kiss-o'-death (KoD) packets sent
495 @comment node-name, next, previous, up
522 leap warning indicator (0-3)
526 stratum (1-15)
534 total roundtrip delay to the primary reference clock
545 time constant and poll exponent (log(2) s) (3-17)
548 minimum time constant (log(2) s) (3-10)
583 TAI-UTC offset (s)
595 The jitter and wander statistics are exponentially-weighted RMS averages.
641 @comment node-name, next, previous, up
671 leap indicator (0-3)
675 stratum (0-15)
683 total roundtrip delay to the primary reference clock
706 host mode (1-6)
710 peer mode (1-5)
714 host poll exponent (log(2) s) (3-17)
717 peer poll exponent (log(2) s) (3-17)
721 headway (see @url{rate.html, Rate Management and the Kiss-o'-Death Packet})
731 @item @code{delay}
733 filter delay
753 interleave delay (see @url{xleave.html, NTP Interleaved Modes})
801 @comment node-name, next, previous, up