Lines Matching +full:higher +full:- +full:than +full:- +full:threshold
1 <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
4 <meta http-equiv="content-type" content="text/html;charset=iso-8859-1">
13 <!-- #BeginDate format:En2m -->11-Feb-2020 14:00<!-- #EndDate -->
23 …hich case the exchange is enabled. If <em><tt>delay</tt></em> is greater than zero, it becomes th…
26 …quency of the local clock oscillator. This is the same operation as the <tt>-f</tt> command line o…
28 …loating point number, which records the frequency offset measured in parts-per-million (PPM). The …
34 ….html"><tt>ntpq</tt></a> utility program's <tt>:config</tt> and <tt>config-from-file</tt> commands.
45 …<dd>Enables processing of NTP mode 7 implementation-specific requests which are used by the deprec…
65 …--interface"><tt>-I</tt></a>, <a href="ntpd.html#--interface"><tt>--interface</tt></a>, <a href="n…
67 …-seconds.list">https://hpiers.obspm.fr/iers/bul/bulc/ntp/leap-seconds.list</a> or <a href="ftp://h…
72 …--enable-leap-smear</tt> option to the <tt>configure</tt> script. It specifies the interval over …
74 …with <tt>=</tt>, <tt>+</tt> and <tt>-</tt>, where <tt>=</tt> sets the <tt>syslogmask</tt>, <tt>+</…
82 …ault system <tt>syslog</tt> facility. This is the same operation as the <tt>-l </tt>command line o…
91 …<dd>Lower limit on the MRU list size. When the MRU list has fewer than <tt>mindepth</tt> entries, …
94 … address is to be added to the list, if the oldest entry was updated more than <tt>maxage</tt> sec…
105 <dt id="nonvolatile"><tt>nonvolatile <i>threshold</i></tt></dt>
106 …threshold</tt></i> in seconds to write the frequency file, with default of 1e-7 (0.1 PPM). The fre…
108 …sed in conjunction with the ACTS modem driver (type 18) or the JJY driver (type 40 mode 100 - 180).
110 …For the JJY driver (type 40 mode 100 - 180), the argument is one telephone number used to dial the…
122 The next two numbers must be between 0 and one-half of the poll interval,
134 …ul when dropping root (the <tt>-i</tt> option). The default is 32 megabytes on non-Linux machines…
152 … <dd>Specifies the dispersion increase rate in parts-per-million (PPM) with default 15 PPM.</dd>
154 …<dd>Specifies the frequency offset in parts-per-million (PPM). This option is mutually exclusive w…
156 …-n'-puff filter span, which determines the most recent interval the algorithm will search for a mi…
158 …<dd>Specifies the panic threshold in seconds with default 1000 s. If set to zero, the panic sanity…
160 …threshold in seconds. The default without this command is 0.128 s. If set to zero, step adjustment…
163 …threshold in seconds. The default without this command is 300 s. Since this option also affects th…
166 …<dt id="tos"><tt>tos [basedate <i>date</i> | bcpollbstep <i>poll-gate</i> | beacon <i>beacon</i> |…
171 …-MM-DD</i>) or an integer giving the days since 1900-01-01, the start of the NTP epoch. <tt>ntpd</…
172 …e next Sunday on or following the base date, but obviously not before 1980-01-06. GPS time stamps …
173 …ld time stamp, minus 11 days. 1970-01-02 was chosen as lower bound so the <em>local</em> time is a…
176 <dt><tt>bcpollbstep <i>poll-gate</i></tt></dt>
177 …-in to the broadcast protocol, it is possible that an attacker could perform a carefully-construct…
179 …<dd>The manycast server sends packets at intervals of 64 s if less than <tt>maxclock</tt> servers …
189 …<dd>Specify the synchronization distance threshold used by the clock selection algorithm. The defa…
200 …; however, for critical applications the value should be somewhat higher but less than <tt>mincloc…
202 …<dd>Specify the orphan stratum with default 16. If less than 16 this is the stratum assumed by the…
211 …be specified. In manycast mode these values are used in turn in an expanding-ring search. The defa…