Lines Matching +full:bottom +full:- +full:speed
1 <!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
6 <meta http-equiv="Content-Type" content="text/html;charset=iso-8859-1">
15 <!-- #BeginDate format:En2m -->21-Oct-2010 23:44<!-- #EndDate -->
22 Serial Port: <tt>/dev/arc<i>u</i></tt>; 300 baud, 8-bits, 2-stop, no parity<br>
26 …nux x86. Changes from v1.1 and v1.2 include patches to work with the new ntp-4 code, clock support…
28 …-5.90 on Solaris-1 (SunOS 4.1.3_U1 on an SS1 serving as a router and firewall) and against ntpd3-5…
30 …omething approaching the 2.5 years expected in the usual stand-alone mode, but no battery-life mea…
31 …-Davis</a>. Thanks also to <a href="mailto:lyndond@sentinet.co.uk">Lyndon David</a> for some of th…
34 …-time). In the default or original MSF mode, the time is in `local' format, including the daylight…
35 …speed from clock to host, and the fact that the clock is not in continuous sync with MSF, it seems…
37 …k's reported time, you might fudge the clock to stratum 1 to allow a stratum-2 secondary server to…
38 …ality reported by the clock. If the signal quality is too low (0--2 out of a range of 0--5), we ch…
41 …<p>When alternate modes 1-3 are selected, the driver can be configured to ignore the resync reques…
44 <li>Your RS232 interface must drive both +ve and -ve
48 …this driver. Each command consists of a single letter (of which only the bottom four bits are sign…
81 <dt>bit 2--0
82 …<dd>reception signal quality in the range 0--5 (very poor to very good); if in the range 0--2 no s…
87 …<dd>Request timestamp. Start bit of first byte of response is on-time, so may be delayed up to 1 s…
115 0 = non-leap year<br>
145 (WWVB) resets if not successful between 0300-0400
147 …<dd>= 1 if the clock has valid time---reset to zero when clock is reset (eg at power-up), and set …
150 …<p>The driver only accepts time from the clock if the bottom three bits of the status byte are <tt…
155 #------------------------------------------------------------------------------
168 peer 11.22.33.9 # tick(1--2).
174 #------------------------------------------------------------------------------
196 … negative) offset implied by any such character, ie with the smallest kernel-induced display, and …
198 …-second insertion or deletion would happen if it is going to. This should help compensate for the …
200 …<dd>Currently set to <tt>-4</tt>, but you may wish to set it to <tt>-5</tt> if you are more conser…
203 …n to the <tt>clockstats</tt> file with a signal quality value appended (`0'--`5' as reported by th…
209 May 10 11:14:06 oolong ntpd[615]: ARCRON: sync finished, signal quality -1: UNKNOWN, will use clock…
220 <dd>0 - Default, Original MSF
221 <dd>1 - Updated MSF
222 <dd>2 - New DCF77
223 <dd>3 - New WWVB
231 …rom one to four characters, with default <tt>MSFa</tt>. When used in modes 1-3, the driver will re…
233 …<dd>(Modes 1-3) If set to 0 (the default), the clock is set to UTC time. If set to 1, the clock is…
235 …<dd>(Modes 1-3) If set to 0 (the default), the clock will be forced to resync approximately every …