Lines Matching +full:allow +full:- +full:set +full:- +full:time
1 <!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
6 <meta http-equiv="Content-Type" content="text/html;charset=iso-8859-1">
15 <!-- #BeginDate format:En2m -->21-Oct-2010 23:44<!-- #EndDate -->
22 Serial Port: <tt>/dev/arc<i>u</i></tt>; 300 baud, 8-bits, 2-stop, no parity<br>
25 …quot;<tt>MSF</tt>'', "<tt>DCF</tt>'' or "<tt>WWVB</tt>'' to indicate the time source.</p>
26 …nux x86. Changes from v1.1 and v1.2 include patches to work with the new ntp-4 code, clock support…
28 …-5.90 on Solaris-1 (SunOS 4.1.3_U1 on an SS1 serving as a router and firewall) and against ntpd3-5…
30 … to allow the unit to run from batteries as designed, for something approaching the 2.5 years expe…
31 …-Davis</a>. Thanks also to <a href="mailto:lyndond@sentinet.co.uk">Lyndon David</a> for some of th…
32 …ref="http://www.arctime.com">Atomic Time</a> as their <a href="http://www.atomictime.com/Product17…
34 …-time). In the default or original MSF mode, the time is in `local' format, including the daylight…
35 …time, and given the low data transmission speed from clock to host, and the fact that the clock is…
36 …<p>Even a busy and slow IP link can yield lower dispersions than this from polls of primary time s…
37 …e systematic errors in the clock's reported time, you might fudge the clock to stratum 1 to allow …
38 …time each hour to avoid any systematic problems with the signal or host). Whilst resyncing, the dr…
39 … the unit runs from. During clock resync this driver tries to take enough time samples to avoid <t…
40 …allow enough samples of the clock to be taken for <tt>ntpd</tt> to sync immediately to this clock …
41 …<p>When alternate modes 1-3 are selected, the driver can be configured to ignore the resync reques…
44 <li>Your RS232 interface must drive both +ve and -ve
48 …allow the unit to echo the character, and then by a further 10ms. Following the echo of the comman…
81 <dt>bit 2--0
82 …<dd>reception signal quality in the range 0--5 (very poor to very good); if in the range 0--2 no s…
85 …time and date should be correct and the phase within 20ms of time as transmitted from the source s…
87 …t bit of first byte of response is on-time, so may be delayed up to 1 second. Note that the driver…
93 <li>seconds tens (seconds presumed to range from 00 to 60 to allow for leap second)
115 0 = non-leap year<br>
122 … (WWVB) 0 if ST is in effect, 1 if DST is in effect, 1 if transition from ST with bit 0 is set to 0
125 …(WWVB) 0 if ST is in effect, 1 if DST is in effect, 0 if transition from DST with bit 1 is set to 0
145 (WWVB) resets if not successful between 0300-0400
147 …<dd>= 1 if the clock has valid time---reset to zero when clock is reset (eg at power-up), and set …
150 …time from the clock if the bottom three bits of the status byte are <tt>011</tt> or <tt>flag2</tt>…
155 #------------------------------------------------------------------------------
168 peer 11.22.33.9 # tick(1--2).
171 # This shouldn't get swept away unless left untouched for a long time.
174 #------------------------------------------------------------------------------
178 # By default, don't trust and don't allow modifications. Ignore in fact.
181 # Allow others in our subnet to check us out...
184 # Trust our peers for time. Don't trust others in case they are insane.
189 # Allow anything from the local host.
194 …time sources, so will bend over backwards to use the time from the clock when available and avoid …
196 … negative) offset implied by any such character, ie with the smallest kernel-induced display, and …
198 …-second insertion or deletion would happen if it is going to. This should help compensate for the …
200 …<dd>Currently set to <tt>-4</tt>, but you may wish to set it to <tt>-5</tt> if you are more conser…
203 …n to the <tt>clockstats</tt> file with a signal quality value appended (`0'--`5' as reported by th…
209 May 10 11:14:06 oolong ntpd[615]: ARCRON: sync finished, signal quality -1: UNKNOWN, will use clock…
220 <dd>0 - Default, Original MSF
221 <dd>1 - Updated MSF
222 <dd>2 - New DCF77
223 <dd>3 - New WWVB
224 <dt><tt>time1 <i>time</i></tt>
225 …<dd>Specifies the time offset calibration factor, in seconds and fraction, with default 0.0. On a …
226 <dt><tt>time2 <i>time</i></tt>
229 … clock be not be fudged higher than stratum 1 so that it is used a backup time source rather than …
231 …rom one to four characters, with default <tt>MSFa</tt>. When used in modes 1-3, the driver will re…
233 …<dd>(Modes 1-3) If set to 0 (the default), the clock is set to UTC time. If set to 1, the clock is…
235 …<dd>(Modes 1-3) If set to 0 (the default), the clock will be forced to resync approximately every …
237 …<dd>If set to 1, better precision is reported (and thus lower dispersion) while clock's received s…