Lines Matching +full:pre +full:- +full:configurable
1 <!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
6 <meta http-equiv="Content-Type" content="text/html;charset=iso-8859-1">
15 <!-- #BeginDate format:En2m -->21-Oct-2010 23:44<!-- #EndDate -->
22 Serial Port: <tt>/dev/arc<i>u</i></tt>; 300 baud, 8-bits, 2-stop, no parity<br>
26 … and v1.2 include patches to work with the new ntp-4 code, clock support for DCF and WWVB configur…
28 …-5.90 on Solaris-1 (SunOS 4.1.3_U1 on an SS1 serving as a router and firewall) and against ntpd3-5…
30 …omething approaching the 2.5 years expected in the usual stand-alone mode, but no battery-life mea…
31 …-Davis</a>. Thanks also to <a href="mailto:lyndond@sentinet.co.uk">Lyndon David</a> for some of th…
34 …-time). In the default or original MSF mode, the time is in `local' format, including the daylight…
35 …-5 or -4, -4 being used in this code, which builds in a reported dispersion of over 63ms (ie says …
37 …k's reported time, you might fudge the clock to stratum 1 to allow a stratum-2 secondary server to…
38 …ality reported by the clock. If the signal quality is too low (0--2 out of a range of 0--5), we ch…
41 …<p>When alternate modes 1-3 are selected, the driver can be configured to ignore the resync reques…
44 <li>Your RS232 interface must drive both +ve and -ve
81 <dt>bit 2--0
82 …<dd>reception signal quality in the range 0--5 (very poor to very good); if in the range 0--2 no s…
87 …<dd>Request timestamp. Start bit of first byte of response is on-time, so may be delayed up to 1 s…
115 0 = non-leap year<br>
145 (WWVB) resets if not successful between 0300-0400
147 …<dd>= 1 if the clock has valid time---reset to zero when clock is reset (eg at power-up), and set …
153 <pre># hostname(n) means we expect (n) to be the stratum at which hostname runs.
155 #------------------------------------------------------------------------------
168 peer 11.22.33.9 # tick(1--2).
174 #------------------------------------------------------------------------------
190 restrict 127.0.0.1</pre>
196 … negative) offset implied by any such character, ie with the smallest kernel-induced display, and …
198 …-second insertion or deletion would happen if it is going to. This should help compensate for the …
200 …<dd>Currently set to <tt>-4</tt>, but you may wish to set it to <tt>-5</tt> if you are more conser…
203 …n to the <tt>clockstats</tt> file with a signal quality value appended (`0'--`5' as reported by th…
206 <pre>May 10 10:15:24 oolong ntpd[615]: ARCRON: unit 0: sending resync command
209 May 10 11:14:06 oolong ntpd[615]: ARCRON: sync finished, signal quality -1: UNKNOWN, will use clock…
213 May 10 12:41:34 oolong ntpd[615]: ARCRON: sync finished, signal quality 3: OK, will use clock</pre>
220 <dd>0 - Default, Original MSF
221 <dd>1 - Updated MSF
222 <dd>2 - New DCF77
223 <dd>3 - New WWVB
231 …rom one to four characters, with default <tt>MSFa</tt>. When used in modes 1-3, the driver will re…
233 …<dd>(Modes 1-3) If set to 0 (the default), the clock is set to UTC time. If set to 1, the clock is…
235 …<dd>(Modes 1-3) If set to 0 (the default), the clock will be forced to resync approximately every …