Merge the NETGRAPH branch into HEAD. tty devices now use netgraph's line
discipline to do the async escaping, but no other benefits are available yet.

Change ``ifdef HAVE_DES'' to ``ifndef NODES''

Merge the NETGRAPH branch into HEAD. tty devices now use netgraph's line
discipline to do the async escaping, but no other benefits are available yet.

Change ``ifdef HAVE_DES'' to ``ifndef NODES'' for consistency.

Make the Makefile a little more sane WRT RELEASE_CRUNCH.

show more ...

socket()s first argument should be a protocol family rather than an
address family.

socket's first argument is an address family, not a protocol family.

Handle hardware-imposed MTU/MRU limitations. PPPoE will no longer
allow MRU/MTU negotiations to exceed 1492.

Add an optional ``max'' specifier to ``set m[rt]u'', ie.

set mtu max 1480

Bump the pp

Handle hardware-imposed MTU/MRU limitations. PPPoE will no longer
allow MRU/MTU negotiations to exceed 1492.

Add an optional ``max'' specifier to ``set m[rt]u'', ie.

set mtu max 1480

Bump the ppp version number.

Sponsored by: Monzoon Networks AG and FreeBSD Services Limited

show more ...

Use fstat to check if descriptor 0 is a socket.

Suggested by: julian

Return -2 when tcp_OpenConnection() fails so that ppp doesn't
report that the device name is of an invalid format.

Change ``set cd'' so that its default value is device specific. The
default is still 1 second for ttys, but is now 6 seconds for i4b (ISDN)
devices and 5 seconds for ethernet (PPPoE) devices.

Support PPPoE

Help (lots) from: julian, archie
Facilities from: ahebert@pubnix.net

Back out the bogus #ifdef __NetBSD__ #include <signal.h> lines.
The original report was due to a mis-installation of the NetBS
header files :-/

Submitted by: Kazuyoshi Kato <kazk@yyy.or.jp>

NetBSD has moved ``extern int errno;'' to signal.h :-/

Submitted by: Kazuyoshi Kato <kazk@yyy.or.jp>

$Id$ -> $FreeBSD$

Add ISDN support via isdnd & i4b. This requires version
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.

Ppp controls the phone number, but idle timers and
S

Add ISDN support via isdnd & i4b. This requires version
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.

Ppp controls the phone number, but idle timers and
SYNC/RAW decisions are still made by isdnd (in isdnd.rc).

This involves a new datalink state machine phase. The
``wait for carrier'' phase happens after dialing but
before logging in. The whole dial state should really
be abstracted so that each device type can deal with it
in its own way (thinking about PPPoE) - but that'll have
to wait.

The ``set cd'' symantics remain the same for tty devices,
but we now delay until we either get CD or timeout waiting
(at which time we drop the link if we require CD).

For i4b devices we always insist on carrier.

Thanks to hm@ for his help, and especially for pointing out
that I *don't* need to re-implement isdnd (that was a huge
waste of time !) :-]

show more ...

Correct the way ppp transfers links on the server side in MP
mode by padding out the ``struct device'' to the maximum
device size.
Bump the ppp version number to indicate the transfer format
change.

Correct the way ppp transfers links on the server side in MP
mode by padding out the ``struct device'' to the maximum
device size.
Bump the ppp version number to indicate the transfer format
change.

This should make MP over tty and udp devices functional again.

show more ...

Correct the ``ignoring sync/async'' warnings so that they show
up with the correct device type.
Reassign the correct tcpdevice or execdevice after transfering
a link in MP server mode.

Allow ``host:port/udp'' devices and support ``host:port/tcp'' as
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.

A udp device uses synchronous ppp rathe

Allow ``host:port/udp'' devices and support ``host:port/tcp'' as
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.

A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.

This proves that PPPoE is plausable in userland....

This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !

iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.

The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').

Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.

Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.

Assign our physical device name for incoming tcp connections by
calling getpeername().

Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().

show more ...

o Redesign the layering mechanism and make the aliasing code part of
the layering.

We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static

o Redesign the layering mechanism and make the aliasing code part of
the layering.

We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.

Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.

o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.

show more ...