Merge from HEAD

Provide the tty-layer mutex when initializing the pps api. This allows
time_pps_fetch() to be used in blocking mode.

Also, don't init the pps api for system devices (consoles) that provide a
custom

Provide the tty-layer mutex when initializing the pps api. This allows
time_pps_fetch() to be used in blocking mode.

Also, don't init the pps api for system devices (consoles) that provide a
custom attach routine. The device may actually be a keyboard or other non-
tty device. If it wants to do pps processing (unlikely) it must handle
everything for itself. (In reality, only a sun keyboard uses a custom
attach routine, and it doesn't make a good pps device.)

show more ...

Merge ^/head r285793 through r285923.

- Since r253161, uart_intr() abuses FILTER_SCHEDULE_THREAD for signaling
uart_bus_attach() during its test that 20 iterations weren't sufficient
for clearing all pending interrupts, assuming this

- Since r253161, uart_intr() abuses FILTER_SCHEDULE_THREAD for signaling
uart_bus_attach() during its test that 20 iterations weren't sufficient
for clearing all pending interrupts, assuming this means that hardware
is broken and doesn't deassert interrupts. However, under pressure, 20
iterations also can be insufficient for clearing all pending interrupts,
leading to a panic as intr_event_handle() tries to schedule an interrupt
handler not registered. Solve this by introducing a flag that is set in
test mode and otherwise restores pre-r253161 behavior of uart_intr(). The
approach of additionally registering uart_intr() as handler as suggested
in PR 194979 is not taken as that in turn would abuse special pccard and
pccbb handling code of intr_event_handle(). [1]
- Const'ify uart_driver_name.
- Fix some minor style bugs.

PR: 194979 [1]
Reviewed by: marcel (earlier version)
MFC after: 3 days

show more ...

Catch up with HEAD (r280229-r284686).

Merge sync of head

Merge from head

MFH: r280643-r281852

Sponsored by: The FreeBSD Foundation

Add support for the uart classes to set their default register shift value.
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the

Add support for the uart classes to set their default register shift value.
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.

This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.

MFC after: 1 week

show more ...

Merge fresh head.

IFC @247348.

Sync with HEAD.

uart: add resume method and enable it for attachments on the most common
x86 buses

Otherwise the uart hardware could be in such a state after the resume
where IER is cleared and thus no interrupts a

uart: add resume method and enable it for attachments on the most common
x86 buses

Otherwise the uart hardware could be in such a state after the resume
where IER is cleared and thus no interrupts are generated.

This behavior is observed and tested with QEMU, so I am comitting this
change to help with my debugging.
There has been no feedback from users of serial ports on real hardware.

MFC after: 20 days

show more ...

MFC

Merge head r233826 through r234834.

IFC @ r234692

sys/amd64/include/cpufunc.h
sys/amd64/include/fpu.h
sys/amd64/amd64/fpu.c
sys/amd64/vmm/vmm.c

- Add API to allow vmm FPU state init/save/restore.

FP stuff discussed with: kib

Complete polled-mode operation by using a callout if the device will be
used in polled-mode. The callout invokes uart_intr, which rearms the timeout.
Implemented for bhyve, but generically useful for

Complete polled-mode operation by using a callout if the device will be
used in polled-mode. The callout invokes uart_intr, which rearms the timeout.
Implemented for bhyve, but generically useful for e.g. embedded bringup
when the interrupt controller hasn't been setup, or if it's not deemed
worthy to wire an interrupt line from a serial port.

Submitted by: neel
Reviewed by: marcel
Obtained from: NetApp
MFC after: 3 weeks

show more ...

IFH@204581

MFC @199204

MFC change 197721:
Fix RTS/CTS flow control, broken by the TTY overhaul. The new TTY
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-fro

MFC change 197721:
Fix RTS/CTS flow control, broken by the TTY overhaul. The new TTY
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.

Approved by: re (kib)

show more ...

Fix RTS/CTS flow control, broken by the TTY overhaul. The new TTY
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
fro

Fix RTS/CTS flow control, broken by the TTY overhaul. The new TTY
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.

MFC after: 1 week

show more ...

Don't expose the uart_ops structure directly, but instead have
it obtained through the uart_class structure. This allows us
to declare the uart_class structure as weak and as such allows
us to refere

Don't expose the uart_ops structure directly, but instead have
it obtained through the uart_class structure. This allows us
to declare the uart_class structure as weak and as such allows
us to reference it even when it's not compiled-in.
It also allows is to get the uart_ops structure by name, which
makes it possible to implement the dt tag handling in uart_getenv().
The side-effect of all this is that we're using the uart_class
structure more consistently which means that we now also have
access to the size of the bus space block needed by the hardware
when we map the bus space, eliminating any hardcoding.

show more ...

Implement the ipend() method of the serdev I/F.

Eliminate the sc_hasfifo flag from the softc. It was only used by
the NS8250 class driver. The UART has FIFOs if sc_rxfifosz>1, so
test for that instead.
While here properly initialize sc_rxfifosz an

Eliminate the sc_hasfifo flag from the softc. It was only used by
the NS8250 class driver. The UART has FIFOs if sc_rxfifosz>1, so
test for that instead.
While here properly initialize sc_rxfifosz and sc_txfifosz in the
case the UART doesn't have FIFOs.

show more ...

Add support for scc(4).