Fix a few issues with HyperTransport devices and MSI interrupts:
- Always enable the HyperTransport MSI mapping window for HyperTransport
to PCI bridges (these show up as HyperTransport slave devic

Fix a few issues with HyperTransport devices and MSI interrupts:
- Always enable the HyperTransport MSI mapping window for HyperTransport
to PCI bridges (these show up as HyperTransport slave devices).
The mapping windows in PCI-PCI bridges are enabled by existing code
in the PCI-PCI bridge driver as MSI requests propagate up the device
tree, but Host-PCI bridges don't really show up in that tree.
- If the PCI device at domain 0 bus 0 slot 0 function 0 is not a
HyperTransport device, then blacklist MSI on any other HT devices in
the system. Linux has a similar quirk.

PR: kern/155442
Tested by: Zack Dannar zdannar of gmail
MFC after: 1 week

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@214309

Sync: merge r214077 through r214219 from ^/head.

Update PCI power management registers per PCI Bus Power Management Interface
Specification Rev. 1.2. Rename pp_pcmcsr field of PM capabilities to pp_bse
to avoid further confusions and adjust some c

Update PCI power management registers per PCI Bus Power Management Interface
Specification Rev. 1.2. Rename pp_pcmcsr field of PM capabilities to pp_bse
to avoid further confusions and adjust some comments accordingly. The real
PMCSR (Power Management Control/Status Register) is PCIR_POWER_STATUS and
it is actually BSE (PCI-to-PCI Bridge Support Extensions) register.

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@209749

Virtualize pci_remap_msi_irq() call from general MSI code. It allows MSI
(FSB interrupts) to be used by non-PCI devices, such as HPET.

IFH@204581

MFC r203528:
Add pci_get|set_max_read_req() helper functions to control maximum PCIe
read request size.

Add pci_get|set_max_read_req() helper functions to control maximum PCIe
read request size.

Reviewed by: jhb@

- MFC

Merge from head

MFC r197077: pci: remove definitions of duplicate constants

Suggested by: jhb
Reviewed by: jhb
Approved by: re (kib)

pci: remove definitions of duplicate constants

Suggested by: jhb
Reviewed by: jhb
MFC after: 1 week

- Merge from HEAD

Adjust some comments.

SATA device on some nForce based boards could get confused if MSI is not
used but MSI to HyperTransport IRQ mapping is enabled, and would act as
if MSI is turned on, resulting in interrupt loss.

Thi

SATA device on some nForce based boards could get confused if MSI is not
used but MSI to HyperTransport IRQ mapping is enabled, and would act as
if MSI is turned on, resulting in interrupt loss.

This commit will,
1. enable MSI mapping on a device only when MSI is enabled for that
device and the MSI address matches the HT mapping window.
2. enable MSI mapping on a bridge only when a downstream device is
allocated an MSI address in the mapping window

PR: kern/118842
Reviewed by: jhb
MFC after: 1 week

show more ...

Remove some remnant alpha hacks.

Approved by: PCI-maintainers (imp, jhb)

Remove a trailing comma which FlexeLint whines about.

Make the PCI code aware of PCI domains (aka PCI segments) so we can
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
d

Make the PCI code aware of PCI domains (aka PCI segments) so we can
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.

Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)

show more ...

Revamp the MSI/MSI-X code a bit to achieve two main goals:
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
-

Revamp the MSI/MSI-X code a bit to achieve two main goals:
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.

The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.

MFC after: 1 month

show more ...

Change the VPD code to read the VPD data on-demand when a driver asks for
it via pci_get_vpd_*() rather than always reading it for each device during
boot. I've left the tunable so that it can still

Change the VPD code to read the VPD data on-demand when a driver asks for
it via pci_get_vpd_*() rather than always reading it for each device during
boot. I've left the tunable so that it can still be turned off if a device
driver causes a lockup via a query to a broken device, but devices whose
drivers do not use VPD (the vast majority) should no longer result in
lockups during boot, and most folks should not need to tweak the tunable
now.

Tested on: bge(4)
Silence from: jmg

show more ...

Expand the MSI/MSI-X API to address some deficiencies in the MSI-X support.
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating

Expand the MSI/MSI-X API to address some deficiencies in the MSI-X support.
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating powerof2() messages for
example where MSI-X does not. To address this, split out the MSI-X
support from pci_msi_count() and pci_alloc_msi() into new driver-visible
functions pci_msix_count() and pci_alloc_msix(). As a result,
pci_msi_count() now just returns a count of the max supported MSI
messages for the device, and pci_alloc_msi() only tries to allocate MSI
messages. To get a count of the max supported MSI-X messages, use
pci_msix_count(). To allocate MSI-X messages, use pci_alloc_msix().
pci_release_msi() still handles both MSI and MSI-X messages, however.
As a result of this change, drivers using the existing API will only
use MSI messages and will no longer try to use MSI-X messages.
- Because MSI-X allows for each message to have its own data and address
values (and thus does not require all of the messages to have their
MD vectors allocated as a group), some devices allow for "sparse" use
of MSI-X message slots. For example, if a device supports 8 messages
but the OS is only able to allocate 2 messages, the device may make the
best use of 2 IRQs if it enables the messages at slots 1 and 4 rather
than default of using the first N slots (or indicies) at 1 and 2. To
support this, add a new pci_remap_msix() function that a driver may call
after a successful pci_alloc_msix() (but before allocating any of the
SYS_RES_IRQ resources) to allow the allocated IRQ resources to be
assigned to different message indices. For example, from the earlier
example, after pci_alloc_msix() returned a value of 2, the driver would
call pci_remap_msix() passing in array of integers { 1, 4 } as the
new message indices to use. The rid's for the SYS_RES_IRQ resources
will always match the message indices. Thus, after the call to
pci_remap_msix() the driver would be able to access the first message
in slot 1 at SYS_RES_IRQ rid 1, and the second message at slot 4 at
SYS_RES_IRQ rid 4. Note that the message slots/indices are 1-based
rather than 0-based so that they will always correspond to the rid
values (SYS_RES_IRQ rid 0 is reserved for the legacy INTx interrupt).
To support this API, a new PCIB_REMAP_MSIX() method was added to the
pcib interface to change the message index for a single IRQ.

Tested by: scottl

show more ...

Add a first pass at a way to blacklist MSI on systems where it doesn't
work:
- A new PCI quirk (PCI_QUIRK_DISABLE_MSI) is added to the quirk table.
- A new pci_msi_device_blacklisted() determines if

Add a first pass at a way to blacklist MSI on systems where it doesn't
work:
- A new PCI quirk (PCI_QUIRK_DISABLE_MSI) is added to the quirk table.
- A new pci_msi_device_blacklisted() determines if a passed in device
matches an MSI quirk in the quirk table. This can be overridden (all
quirks ignored) by setting the hw.pci.honor_msi_blacklist to 0.
- A global blacklist check is performed in the MI PCI bus code by checking
to see if the device at 0:0:0 is blacklisted.

Tested by: jdp

show more ...

Replace #define<space> with #define<tab> so the code is consistent with
style(9) and avoids mixing the two formats.

Fix a couple of comment typos.

Reported by: ru