Sync to HEAD@r272516.

Reintegrate head@r272414

Sponsored by: The FreeBSD Foundation

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different R

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.

To make this possible:

* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.

This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.

Tested:

* AR9380 (STA)
* AR9485 CUS198 (STA)

Obtained from: Qualcomm Atheros, Linux ath9k

show more ...

IFC @r269962

Submitted by: Anish Gupta (akgupt3@gmail.com)

Merge head from 7/28

Sync to HEAD@r269943.

Remove ia64.

This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in com

Remove ia64.

This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation

This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h

Discussed at: BSDcan

show more ...

Merge head

IFC @264767

MFC @ r259205 in preparation for some SVM updates. (for real this time)

Merge head r232040 through r257457.
M usr.sbin/portsnap/portsnap/portsnap.8
M usr.sbin/portsnap/portsnap/portsnap.sh
M usr.sbin/tcpdump/tcpdump/Makefile

Include necessary headers that now are available due to pollution
via if_var.h.

Sponsored by: Netflix
Sponsored by: Nginx, Inc.

Merge fresh head.

IFC @247348.

Sync with HEAD.

Create a new TX lock specifically for queuing frames.

This now separates out the act of queuing frames from the act of running
TX and TX completion.

MFC

MFC @ r241285

IFC @ r242684

Sync from head

I give up - introduce a TX lock to serialise TX operations.

I've tried serialising TX using queues and such but unfortunately
due to how this interacts with the locking going on elsewhere in the
net

I give up - introduce a TX lock to serialise TX operations.

I've tried serialising TX using queues and such but unfortunately
due to how this interacts with the locking going on elsewhere in the
networking stack, the TX task gets delayed, resulting in quite a
noticable throughput loss:

* baseline TCP for 2x2 11n HT40 is ~ 170mbit/sec;
* TCP for TX task in the ath taskq, with the RX also going on - 80mbit/sec;
* TCP for TX task in a separate, second taskq - 100mbit/sec.

So for now I'm going with the Linux wireless stack approach - lock tx
early. The linux code does in the wireless stack, before the 802.11
state stuff happens and before it's punted to the driver.
But TX locking needs to also occur at the driver layer as the TX
completion code _also_ begins to drain the ifnet TX queue.

Whilst I'm here, add some KTR traces for the TX path.

Note:

* This really should be done at the net80211 layer (as well, at least.)
But that'll have to wait for a little more thought to happen.

show more ...

Merge head r233826 through r239010.

Flesh out a new DMA map for the EDMA TX completion status, as well
as a lock to go with that whole code path.

Merge head r236710 through r238467.

Create an RX queue lock.

Ideally these locks would go away and there'd be a single driver lock,
like what iwn(4) does. I'll worry about that later.