Make CAM report devices with ATA/SATA transport to devstat(9) as IDE.

IFH@204581

MFC r203108:
Large set of CAM improvements:
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from

MFC r203108:
Large set of CAM improvements:
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.

show more ...

MFp4: Large set of CAM inprovements.

- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many

MFp4: Large set of CAM inprovements.

- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.

show more ...

Merge from head at r201628.

# This hasn't been tested, and there are at least three bad commits
# that need to be backed out before the branch will be stable again.

MFC r199279, r199280, r199281:
- Fix several device freeze counting bugs.
- Remove code that years ago was closing race between request submission
to SIM and device/SIM freeze. That race become impos

MFC r199279, r199280, r199281:
- Fix several device freeze counting bugs.
- Remove code that years ago was closing race between request submission
to SIM and device/SIM freeze. That race become impossible after moving from
spl to mutex locking, while this workaround causes some unexpected effects.

show more ...

MFC r198382, r198385:
Replace most of priority numbers with defines. No logical changes.

MFp4:
Fix several device freeze counting bugs.

MFC @199204

Replace most of priority numbers with defines. No logical changes.

Merge from head

Merge from head up to r188941 (last revision before the USB stack switch)

- MFC @196061

Separate the parallel scsi knowledge out of the core of the XPT, and
modularize it so that new transports can be created.

Add a transport for SATA

Add a periph+protocol layer for ATA

Add a driver

Separate the parallel scsi knowledge out of the core of the XPT, and
modularize it so that new transports can be created.

Add a transport for SATA

Add a periph+protocol layer for ATA

Add a driver for AHCI-compliant hardware.

Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.

The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.

ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.

This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.

Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.

The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.

Submitted by: scottl, mav
Approved by: re

show more ...

Don't call destroy_dev(9) with a mutex held. While here, shuffle
things around so the periph destructors look alike. Based on a patch
by Jaakko Heinonen.

Submitted by: Jaakko Heinonen
Reviewed by:

Don't call destroy_dev(9) with a mutex held. While here, shuffle
things around so the periph destructors look alike. Based on a patch
by Jaakko Heinonen.

Submitted by: Jaakko Heinonen
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation

show more ...

Add a helper function for registering async callbacks. Besides
eliminating a lot of duplicated code, this also fixes a locking edge case.

Eliminate the use of M_TEMP.

Remove Giant from CAM. Drivers (SIMs) now register a mutex that CAM will
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant a

Remove Giant from CAM. Drivers (SIMs) now register a mutex that CAM will
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.

The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.

show more ...

Add an xpt_print function to reduce most of the xpt_print_path/printf
pairs. Convert the core code to use it.

Reviewed by: scsi (various folks weighing in with good advice)
MFC after: 2 weeks

Fix a place where we were referencing a pointer after it had been freed.

Submitted by: "Henry Miller" <hank@blackhole.com>
MFC after: 3 days

Start each of the license/copyright comments with /*-

Do the dreaded s/dev_t/struct cdev */
Bump __FreeBSD_version accordingly.

Device megapatch 4/6:

Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.

Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT fl

Device megapatch 4/6:

Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.

Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.

show more ...

Device megapatch 1/6:

Free approx 86 major numbers with a mostly automatically generated patch.

A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use

Device megapatch 1/6:

Free approx 86 major numbers with a mostly automatically generated patch.

A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.

show more ...

Use __FBSDID().