1 /* 2 * CDDL HEADER START 3 * 4 * The contents of this file are subject to the terms of the 5 * Common Development and Distribution License (the "License"). 6 * You may not use this file except in compliance with the License. 7 * 8 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9 * or http://www.opensolaris.org/os/licensing. 10 * See the License for the specific language governing permissions 11 * and limitations under the License. 12 * 13 * When distributing Covered Code, include this CDDL HEADER in each 14 * file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15 * If applicable, add the following below this CDDL HEADER, with the 16 * fields enclosed by brackets "[]" replaced with your own identifying 17 * information: Portions Copyright [yyyy] [name of copyright owner] 18 * 19 * CDDL HEADER END 20 */ 21 /* 22 * Copyright 2006 Sun Microsystems, Inc. All rights reserved. 23 * Use is subject to license terms. 24 */ 25 26 #ifndef _SYS_SCSI_SCSI_PKT_H 27 #define _SYS_SCSI_SCSI_PKT_H 28 29 #pragma ident "%Z%%M% %I% %E% SMI" 30 31 #include <sys/scsi/scsi_types.h> 32 33 #ifdef __cplusplus 34 extern "C" { 35 #endif 36 37 #ifdef _KERNEL 38 /* 39 * SCSI packet definition. 40 * 41 * This structure defines the packet which is allocated by a library 42 * function and handed to a target driver. The target driver fills 43 * in some information, and passes it to the library for transport 44 * to an addressed SCSI device. The host adapter found by 45 * the library fills in some other information as the command is 46 * processed. When the command completes (or can be taken no further) 47 * the function specified in the packet is called with a pointer to 48 * the packet as it argument. From fields within the packet, the target 49 * driver can determine the success or failure of the command. 50 */ 51 struct scsi_pkt { 52 opaque_t pkt_ha_private; /* private data for host adapter */ 53 struct scsi_address pkt_address; /* destination packet is for */ 54 opaque_t pkt_private; /* private data for target driver */ 55 void (*pkt_comp)(struct scsi_pkt *); /* completion routine */ 56 uint_t pkt_flags; /* flags */ 57 int pkt_time; /* time allotted to complete command */ 58 uchar_t *pkt_scbp; /* pointer to status block */ 59 uchar_t *pkt_cdbp; /* pointer to command block */ 60 ssize_t pkt_resid; /* data bytes not transferred */ 61 uint_t pkt_state; /* state of command */ 62 uint_t pkt_statistics; /* statistics */ 63 uchar_t pkt_reason; /* reason completion called */ 64 uint_t pkt_cdblen; 65 uint_t pkt_tgtlen; 66 uint_t pkt_scblen; 67 ddi_dma_handle_t pkt_handle; 68 uint_t pkt_numcookies; 69 off_t pkt_dma_offset; 70 size_t pkt_dma_len; 71 uint_t pkt_dma_flags; 72 ddi_dma_cookie_t *pkt_cookies; 73 }; 74 #endif /* _KERNEL */ 75 76 /* 77 * Definitions for the pkt_flags field. 78 */ 79 80 /* 81 * Following defines are generic. 82 */ 83 #define FLAG_STAG 0x4000 /* Run command with Simple attribute */ 84 #define FLAG_OTAG 0x2000 /* Run command with Ordered attribute */ 85 #define FLAG_HTAG 0x1000 /* Run command with Head of Queue attribute */ 86 #define FLAG_TAGMASK (FLAG_HTAG|FLAG_OTAG|FLAG_STAG) 87 88 #define FLAG_ACA 0x0100 /* internal; do not use */ 89 #define FLAG_HEAD 0x8000 /* This cmd should be put at the head */ 90 /* of the HBA driver's queue */ 91 #define FLAG_SENSING 0x0400 /* Running request sense for failed pkt */ 92 #define FLAG_NOINTR 0x0001 /* Run command with no cmd completion */ 93 /* callback; command has been completed */ 94 /* upon return from scsi_transport(9F) */ 95 96 /* 97 * Following defines are appropriate for SCSI parallel bus. 98 */ 99 #define FLAG_NODISCON 0x0002 /* Run command without disconnects */ 100 #define FLAG_NOPARITY 0x0008 /* Run command without parity checking */ 101 #define FLAG_RENEGOTIATE_WIDE_SYNC \ 102 0x1000000 /* Do wide and sync renegotiation before */ 103 /* transporting this command to target */ 104 105 /* 106 * Following defines are internal i.e. not part of DDI. 107 */ 108 #define FLAG_IMMEDIATE_CB \ 109 0x0800 /* Immediate callback on command */ 110 /* completion, ie. do not defer */ 111 112 /* 113 * Following defines are for USCSI options. 114 */ 115 #define FLAG_SILENT 0x00010000 116 #define FLAG_DIAGNOSE 0x00020000 117 #define FLAG_ISOLATE 0x00040000 118 119 /* 120 * Following define is for scsi_vhci. 121 * If pHCI cannot transport the command to the device, do not queue the pkt 122 * in pHCI. Return immediately with TRAN_BUSY. 123 */ 124 #define FLAG_NOQUEUE 0x80000000 125 126 /* 127 * Definitions for the pkt_reason field. 128 */ 129 130 /* 131 * Following defines are generic. 132 */ 133 #define CMD_CMPLT 0 /* no transport errors- normal completion */ 134 #define CMD_INCOMPLETE 1 /* transport stopped with not normal state */ 135 #define CMD_DMA_DERR 2 /* dma direction error occurred */ 136 #define CMD_TRAN_ERR 3 /* unspecified transport error */ 137 #define CMD_RESET 4 /* Target completed hard reset sequence */ 138 #define CMD_ABORTED 5 /* Command transport aborted on request */ 139 #define CMD_TIMEOUT 6 /* Command timed out */ 140 #define CMD_DATA_OVR 7 /* Data Overrun */ 141 #define CMD_CMD_OVR 8 /* Command Overrun */ 142 #define CMD_STS_OVR 9 /* Status Overrun */ 143 #define CMD_TERMINATED 22 /* Command transport terminated on request */ 144 145 /* 146 * Following defines are appropriate for SCSI parallel bus. 147 */ 148 #define CMD_BADMSG 10 /* Message not Command Complete */ 149 #define CMD_NOMSGOUT 11 /* Target refused to go to Message Out phase */ 150 #define CMD_XID_FAIL 12 /* Extended Identify message rejected */ 151 #define CMD_IDE_FAIL 13 /* Initiator Detected Error message rejected */ 152 #define CMD_ABORT_FAIL 14 /* Abort message rejected */ 153 #define CMD_REJECT_FAIL 15 /* Reject message rejected */ 154 #define CMD_NOP_FAIL 16 /* No Operation message rejected */ 155 #define CMD_PER_FAIL 17 /* Message Parity Error message rejected */ 156 #define CMD_BDR_FAIL 18 /* Bus Device Reset message rejected */ 157 #define CMD_ID_FAIL 19 /* Identify message rejected */ 158 #define CMD_UNX_BUS_FREE 20 /* Unexpected Bus Free Phase occurred */ 159 #define CMD_TAG_REJECT 21 /* Target rejected our tag message */ 160 #define CMD_DEV_GONE 24 /* The device has been removed */ 161 162 /* Used by scsi_rname(9F) */ 163 #define CMD_REASON_ASCII { \ 164 "cmplt", "incomplete", "dma_derr", "tran_err", "reset", \ 165 "aborted", "timeout", "data_ovr", "cmd_ovr", "sts_ovr", \ 166 "badmsg", "nomsgout", "xid_fail", "ide_fail", "abort_fail", \ 167 "reject_fail", "nop_fail", "per_fail", "bdr_fail", "id_fail", \ 168 "unexpected_bus_free", "tag reject", "terminated", "", "gone", \ 169 NULL } 170 171 /* 172 * Definitions for the pkt_state field 173 */ 174 #define STATE_GOT_BUS 0x01 /* Success in getting SCSI bus */ 175 #define STATE_GOT_TARGET 0x02 /* Successfully connected with target */ 176 #define STATE_SENT_CMD 0x04 /* Command successfully sent */ 177 #define STATE_XFERRED_DATA 0x08 /* Data transfer took place */ 178 #define STATE_GOT_STATUS 0x10 /* SCSI status received */ 179 #define STATE_ARQ_DONE 0x20 /* auto rqsense took place */ 180 181 /* 182 * Definitions for the pkt_statistics field 183 */ 184 185 /* 186 * Following defines are generic. 187 */ 188 #define STAT_BUS_RESET 0x8 /* Reset operation on interconnect */ 189 #define STAT_DEV_RESET 0x10 /* Target completed hard reset sequence */ 190 #define STAT_ABORTED 0x20 /* Command was aborted */ 191 #define STAT_TERMINATED 0x80 /* Command was terminated */ 192 #define STAT_TIMEOUT 0x40 /* Command experienced a timeout */ 193 194 /* 195 * Following defines are appropriate for SCSI parallel bus. 196 */ 197 #define STAT_DISCON 0x1 /* Command experienced a disconnect */ 198 #define STAT_SYNC 0x2 /* Command did a synchronous data transfer */ 199 #define STAT_PERR 0x4 /* Command experienced a SCSI parity error */ 200 201 /* 202 * Definitions for what scsi_transport returns 203 */ 204 #define TRAN_ACCEPT 1 205 #define TRAN_BUSY 0 206 #define TRAN_BADPKT -1 207 #define TRAN_FATAL_ERROR -2 /* HBA cannot accept any pkts */ 208 209 #ifdef _KERNEL 210 /* 211 * Kernel function declarations 212 */ 213 int scsi_transport(struct scsi_pkt *pkt); 214 215 #define pkt_transport scsi_transport 216 217 #define SCSI_POLL_TIMEOUT 60 218 219 #endif /* _KERNEL */ 220 221 #ifdef __cplusplus 222 } 223 #endif 224 225 #endif /* _SYS_SCSI_SCSI_PKT_H */ 226