1 /* 2 * This file contains work-arounds for many known PCI hardware 3 * bugs. Devices present only on certain architectures (host 4 * bridges et cetera) should be handled in arch-specific code. 5 * 6 * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. 7 * 8 * Copyright (c) 1999 Martin Mares <mj@ucw.cz> 9 * 10 * Init/reset quirks for USB host controllers should be in the 11 * USB quirks file, where their drivers can access reuse it. 12 * 13 * The bridge optimization stuff has been removed. If you really 14 * have a silly BIOS which is unable to set your host bridge right, 15 * use the PowerTweak utility (see http://powertweak.sourceforge.net). 16 */ 17 18 #include <linux/config.h> 19 #include <linux/types.h> 20 #include <linux/kernel.h> 21 #include <linux/pci.h> 22 #include <linux/init.h> 23 #include <linux/delay.h> 24 #include <linux/acpi.h> 25 #include "pci.h" 26 27 /* Deal with broken BIOS'es that neglect to enable passive release, 28 which can cause problems in combination with the 82441FX/PPro MTRRs */ 29 static void __devinit quirk_passive_release(struct pci_dev *dev) 30 { 31 struct pci_dev *d = NULL; 32 unsigned char dlc; 33 34 /* We have to make sure a particular bit is set in the PIIX3 35 ISA bridge, so we have to go out and find it. */ 36 while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { 37 pci_read_config_byte(d, 0x82, &dlc); 38 if (!(dlc & 1<<1)) { 39 printk(KERN_ERR "PCI: PIIX3: Enabling Passive Release on %s\n", pci_name(d)); 40 dlc |= 1<<1; 41 pci_write_config_byte(d, 0x82, dlc); 42 } 43 } 44 } 45 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release ); 46 47 /* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround 48 but VIA don't answer queries. If you happen to have good contacts at VIA 49 ask them for me please -- Alan 50 51 This appears to be BIOS not version dependent. So presumably there is a 52 chipset level fix */ 53 int isa_dma_bridge_buggy; /* Exported */ 54 55 static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev) 56 { 57 if (!isa_dma_bridge_buggy) { 58 isa_dma_bridge_buggy=1; 59 printk(KERN_INFO "Activating ISA DMA hang workarounds.\n"); 60 } 61 } 62 /* 63 * Its not totally clear which chipsets are the problematic ones 64 * We know 82C586 and 82C596 variants are affected. 65 */ 66 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs ); 67 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs ); 68 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs ); 69 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs ); 70 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs ); 71 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs ); 72 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs ); 73 74 int pci_pci_problems; 75 76 /* 77 * Chipsets where PCI->PCI transfers vanish or hang 78 */ 79 static void __devinit quirk_nopcipci(struct pci_dev *dev) 80 { 81 if ((pci_pci_problems & PCIPCI_FAIL)==0) { 82 printk(KERN_INFO "Disabling direct PCI/PCI transfers.\n"); 83 pci_pci_problems |= PCIPCI_FAIL; 84 } 85 } 86 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci ); 87 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci ); 88 89 /* 90 * Triton requires workarounds to be used by the drivers 91 */ 92 static void __devinit quirk_triton(struct pci_dev *dev) 93 { 94 if ((pci_pci_problems&PCIPCI_TRITON)==0) { 95 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 96 pci_pci_problems |= PCIPCI_TRITON; 97 } 98 } 99 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton ); 100 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton ); 101 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton ); 102 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton ); 103 104 /* 105 * VIA Apollo KT133 needs PCI latency patch 106 * Made according to a windows driver based patch by George E. Breese 107 * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm 108 * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for 109 * the info on which Mr Breese based his work. 110 * 111 * Updated based on further information from the site and also on 112 * information provided by VIA 113 */ 114 static void __devinit quirk_vialatency(struct pci_dev *dev) 115 { 116 struct pci_dev *p; 117 u8 rev; 118 u8 busarb; 119 /* Ok we have a potential problem chipset here. Now see if we have 120 a buggy southbridge */ 121 122 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); 123 if (p!=NULL) { 124 pci_read_config_byte(p, PCI_CLASS_REVISION, &rev); 125 /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */ 126 /* Check for buggy part revisions */ 127 if (rev < 0x40 || rev > 0x42) 128 goto exit; 129 } else { 130 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); 131 if (p==NULL) /* No problem parts */ 132 goto exit; 133 pci_read_config_byte(p, PCI_CLASS_REVISION, &rev); 134 /* Check for buggy part revisions */ 135 if (rev < 0x10 || rev > 0x12) 136 goto exit; 137 } 138 139 /* 140 * Ok we have the problem. Now set the PCI master grant to 141 * occur every master grant. The apparent bug is that under high 142 * PCI load (quite common in Linux of course) you can get data 143 * loss when the CPU is held off the bus for 3 bus master requests 144 * This happens to include the IDE controllers.... 145 * 146 * VIA only apply this fix when an SB Live! is present but under 147 * both Linux and Windows this isnt enough, and we have seen 148 * corruption without SB Live! but with things like 3 UDMA IDE 149 * controllers. So we ignore that bit of the VIA recommendation.. 150 */ 151 152 pci_read_config_byte(dev, 0x76, &busarb); 153 /* Set bit 4 and bi 5 of byte 76 to 0x01 154 "Master priority rotation on every PCI master grant */ 155 busarb &= ~(1<<5); 156 busarb |= (1<<4); 157 pci_write_config_byte(dev, 0x76, busarb); 158 printk(KERN_INFO "Applying VIA southbridge workaround.\n"); 159 exit: 160 pci_dev_put(p); 161 } 162 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency ); 163 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency ); 164 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency ); 165 166 /* 167 * VIA Apollo VP3 needs ETBF on BT848/878 168 */ 169 static void __devinit quirk_viaetbf(struct pci_dev *dev) 170 { 171 if ((pci_pci_problems&PCIPCI_VIAETBF)==0) { 172 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 173 pci_pci_problems |= PCIPCI_VIAETBF; 174 } 175 } 176 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf ); 177 178 static void __devinit quirk_vsfx(struct pci_dev *dev) 179 { 180 if ((pci_pci_problems&PCIPCI_VSFX)==0) { 181 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 182 pci_pci_problems |= PCIPCI_VSFX; 183 } 184 } 185 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx ); 186 187 /* 188 * Ali Magik requires workarounds to be used by the drivers 189 * that DMA to AGP space. Latency must be set to 0xA and triton 190 * workaround applied too 191 * [Info kindly provided by ALi] 192 */ 193 static void __init quirk_alimagik(struct pci_dev *dev) 194 { 195 if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) { 196 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 197 pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; 198 } 199 } 200 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik ); 201 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik ); 202 203 /* 204 * Natoma has some interesting boundary conditions with Zoran stuff 205 * at least 206 */ 207 static void __devinit quirk_natoma(struct pci_dev *dev) 208 { 209 if ((pci_pci_problems&PCIPCI_NATOMA)==0) { 210 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 211 pci_pci_problems |= PCIPCI_NATOMA; 212 } 213 } 214 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma ); 215 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma ); 216 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma ); 217 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma ); 218 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma ); 219 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma ); 220 221 /* 222 * This chip can cause PCI parity errors if config register 0xA0 is read 223 * while DMAs are occurring. 224 */ 225 static void __devinit quirk_citrine(struct pci_dev *dev) 226 { 227 dev->cfg_size = 0xA0; 228 } 229 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine ); 230 231 /* 232 * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. 233 * If it's needed, re-allocate the region. 234 */ 235 static void __devinit quirk_s3_64M(struct pci_dev *dev) 236 { 237 struct resource *r = &dev->resource[0]; 238 239 if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { 240 r->start = 0; 241 r->end = 0x3ffffff; 242 } 243 } 244 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M ); 245 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M ); 246 247 static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, 248 unsigned size, int nr, const char *name) 249 { 250 region &= ~(size-1); 251 if (region) { 252 struct pci_bus_region bus_region; 253 struct resource *res = dev->resource + nr; 254 255 res->name = pci_name(dev); 256 res->start = region; 257 res->end = region + size - 1; 258 res->flags = IORESOURCE_IO; 259 260 /* Convert from PCI bus to resource space. */ 261 bus_region.start = res->start; 262 bus_region.end = res->end; 263 pcibios_bus_to_resource(dev, res, &bus_region); 264 265 pci_claim_resource(dev, nr); 266 printk("PCI quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name); 267 } 268 } 269 270 /* 271 * ATI Northbridge setups MCE the processor if you even 272 * read somewhere between 0x3b0->0x3bb or read 0x3d3 273 */ 274 static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev) 275 { 276 printk(KERN_INFO "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.\n"); 277 /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ 278 request_region(0x3b0, 0x0C, "RadeonIGP"); 279 request_region(0x3d3, 0x01, "RadeonIGP"); 280 } 281 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce ); 282 283 /* 284 * Let's make the southbridge information explicit instead 285 * of having to worry about people probing the ACPI areas, 286 * for example.. (Yes, it happens, and if you read the wrong 287 * ACPI register it will put the machine to sleep with no 288 * way of waking it up again. Bummer). 289 * 290 * ALI M7101: Two IO regions pointed to by words at 291 * 0xE0 (64 bytes of ACPI registers) 292 * 0xE2 (32 bytes of SMB registers) 293 */ 294 static void __devinit quirk_ali7101_acpi(struct pci_dev *dev) 295 { 296 u16 region; 297 298 pci_read_config_word(dev, 0xE0, ®ion); 299 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); 300 pci_read_config_word(dev, 0xE2, ®ion); 301 quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); 302 } 303 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi ); 304 305 static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 306 { 307 u32 devres; 308 u32 mask, size, base; 309 310 pci_read_config_dword(dev, port, &devres); 311 if ((devres & enable) != enable) 312 return; 313 mask = (devres >> 16) & 15; 314 base = devres & 0xffff; 315 size = 16; 316 for (;;) { 317 unsigned bit = size >> 1; 318 if ((bit & mask) == bit) 319 break; 320 size = bit; 321 } 322 /* 323 * For now we only print it out. Eventually we'll want to 324 * reserve it (at least if it's in the 0x1000+ range), but 325 * let's get enough confirmation reports first. 326 */ 327 base &= -size; 328 printk("%s PIO at %04x-%04x\n", name, base, base + size - 1); 329 } 330 331 static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 332 { 333 u32 devres; 334 u32 mask, size, base; 335 336 pci_read_config_dword(dev, port, &devres); 337 if ((devres & enable) != enable) 338 return; 339 base = devres & 0xffff0000; 340 mask = (devres & 0x3f) << 16; 341 size = 128 << 16; 342 for (;;) { 343 unsigned bit = size >> 1; 344 if ((bit & mask) == bit) 345 break; 346 size = bit; 347 } 348 /* 349 * For now we only print it out. Eventually we'll want to 350 * reserve it, but let's get enough confirmation reports first. 351 */ 352 base &= -size; 353 printk("%s MMIO at %04x-%04x\n", name, base, base + size - 1); 354 } 355 356 /* 357 * PIIX4 ACPI: Two IO regions pointed to by longwords at 358 * 0x40 (64 bytes of ACPI registers) 359 * 0x90 (16 bytes of SMB registers) 360 * and a few strange programmable PIIX4 device resources. 361 */ 362 static void __devinit quirk_piix4_acpi(struct pci_dev *dev) 363 { 364 u32 region, res_a; 365 366 pci_read_config_dword(dev, 0x40, ®ion); 367 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); 368 pci_read_config_dword(dev, 0x90, ®ion); 369 quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); 370 371 /* Device resource A has enables for some of the other ones */ 372 pci_read_config_dword(dev, 0x5c, &res_a); 373 374 piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); 375 piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); 376 377 /* Device resource D is just bitfields for static resources */ 378 379 /* Device 12 enabled? */ 380 if (res_a & (1 << 29)) { 381 piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); 382 piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); 383 } 384 /* Device 13 enabled? */ 385 if (res_a & (1 << 30)) { 386 piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); 387 piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); 388 } 389 piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); 390 piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); 391 } 392 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi ); 393 394 /* 395 * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at 396 * 0x40 (128 bytes of ACPI, GPIO & TCO registers) 397 * 0x58 (64 bytes of GPIO I/O space) 398 */ 399 static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev) 400 { 401 u32 region; 402 403 pci_read_config_dword(dev, 0x40, ®ion); 404 quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH4 ACPI/GPIO/TCO"); 405 406 pci_read_config_dword(dev, 0x58, ®ion); 407 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH4 GPIO"); 408 } 409 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi ); 410 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi ); 411 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi ); 412 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi ); 413 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi ); 414 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi ); 415 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi ); 416 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi ); 417 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi ); 418 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi ); 419 420 static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev) 421 { 422 u32 region; 423 424 pci_read_config_dword(dev, 0x40, ®ion); 425 quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH6 ACPI/GPIO/TCO"); 426 427 pci_read_config_dword(dev, 0x48, ®ion); 428 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH6 GPIO"); 429 } 430 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi ); 431 432 /* 433 * VIA ACPI: One IO region pointed to by longword at 434 * 0x48 or 0x20 (256 bytes of ACPI registers) 435 */ 436 static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev) 437 { 438 u8 rev; 439 u32 region; 440 441 pci_read_config_byte(dev, PCI_CLASS_REVISION, &rev); 442 if (rev & 0x10) { 443 pci_read_config_dword(dev, 0x48, ®ion); 444 region &= PCI_BASE_ADDRESS_IO_MASK; 445 quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES, "vt82c586 ACPI"); 446 } 447 } 448 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi ); 449 450 /* 451 * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at 452 * 0x48 (256 bytes of ACPI registers) 453 * 0x70 (128 bytes of hardware monitoring register) 454 * 0x90 (16 bytes of SMB registers) 455 */ 456 static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev) 457 { 458 u16 hm; 459 u32 smb; 460 461 quirk_vt82c586_acpi(dev); 462 463 pci_read_config_word(dev, 0x70, &hm); 464 hm &= PCI_BASE_ADDRESS_IO_MASK; 465 quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon"); 466 467 pci_read_config_dword(dev, 0x90, &smb); 468 smb &= PCI_BASE_ADDRESS_IO_MASK; 469 quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB"); 470 } 471 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi ); 472 473 /* 474 * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at 475 * 0x88 (128 bytes of power management registers) 476 * 0xd0 (16 bytes of SMB registers) 477 */ 478 static void __devinit quirk_vt8235_acpi(struct pci_dev *dev) 479 { 480 u16 pm, smb; 481 482 pci_read_config_word(dev, 0x88, &pm); 483 pm &= PCI_BASE_ADDRESS_IO_MASK; 484 quirk_io_region(dev, pm, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); 485 486 pci_read_config_word(dev, 0xd0, &smb); 487 smb &= PCI_BASE_ADDRESS_IO_MASK; 488 quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 1, "vt8235 SMB"); 489 } 490 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); 491 492 493 #ifdef CONFIG_X86_IO_APIC 494 495 #include <asm/io_apic.h> 496 497 /* 498 * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip 499 * devices to the external APIC. 500 * 501 * TODO: When we have device-specific interrupt routers, 502 * this code will go away from quirks. 503 */ 504 static void __devinit quirk_via_ioapic(struct pci_dev *dev) 505 { 506 u8 tmp; 507 508 if (nr_ioapics < 1) 509 tmp = 0; /* nothing routed to external APIC */ 510 else 511 tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ 512 513 printk(KERN_INFO "PCI: %sbling Via external APIC routing\n", 514 tmp == 0 ? "Disa" : "Ena"); 515 516 /* Offset 0x58: External APIC IRQ output control */ 517 pci_write_config_byte (dev, 0x58, tmp); 518 } 519 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic ); 520 521 /* 522 * VIA 8237: Some BIOSs don't set the 'Bypass APIC De-Assert Message' Bit. 523 * This leads to doubled level interrupt rates. 524 * Set this bit to get rid of cycle wastage. 525 * Otherwise uncritical. 526 */ 527 static void __devinit quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) 528 { 529 u8 misc_control2; 530 #define BYPASS_APIC_DEASSERT 8 531 532 pci_read_config_byte(dev, 0x5B, &misc_control2); 533 if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { 534 printk(KERN_INFO "PCI: Bypassing VIA 8237 APIC De-Assert Message\n"); 535 pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); 536 } 537 } 538 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 539 540 /* 541 * The AMD io apic can hang the box when an apic irq is masked. 542 * We check all revs >= B0 (yet not in the pre production!) as the bug 543 * is currently marked NoFix 544 * 545 * We have multiple reports of hangs with this chipset that went away with 546 * noapic specified. For the moment we assume its the errata. We may be wrong 547 * of course. However the advice is demonstrably good even if so.. 548 */ 549 static void __devinit quirk_amd_ioapic(struct pci_dev *dev) 550 { 551 u8 rev; 552 553 pci_read_config_byte(dev, PCI_REVISION_ID, &rev); 554 if (rev >= 0x02) { 555 printk(KERN_WARNING "I/O APIC: AMD Errata #22 may be present. In the event of instability try\n"); 556 printk(KERN_WARNING " : booting with the \"noapic\" option.\n"); 557 } 558 } 559 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic ); 560 561 static void __init quirk_ioapic_rmw(struct pci_dev *dev) 562 { 563 if (dev->devfn == 0 && dev->bus->number == 0) 564 sis_apic_bug = 1; 565 } 566 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw ); 567 568 int pci_msi_quirk; 569 570 #define AMD8131_revA0 0x01 571 #define AMD8131_revB0 0x11 572 #define AMD8131_MISC 0x40 573 #define AMD8131_NIOAMODE_BIT 0 574 static void __init quirk_amd_8131_ioapic(struct pci_dev *dev) 575 { 576 unsigned char revid, tmp; 577 578 if (dev->subordinate) { 579 printk(KERN_WARNING "PCI: MSI quirk detected. " 580 "PCI_BUS_FLAGS_NO_MSI set for subordinate bus.\n"); 581 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 582 } 583 584 if (nr_ioapics == 0) 585 return; 586 587 pci_read_config_byte(dev, PCI_REVISION_ID, &revid); 588 if (revid == AMD8131_revA0 || revid == AMD8131_revB0) { 589 printk(KERN_INFO "Fixing up AMD8131 IOAPIC mode\n"); 590 pci_read_config_byte( dev, AMD8131_MISC, &tmp); 591 tmp &= ~(1 << AMD8131_NIOAMODE_BIT); 592 pci_write_config_byte( dev, AMD8131_MISC, tmp); 593 } 594 } 595 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_APIC, quirk_amd_8131_ioapic ); 596 597 static void __init quirk_svw_msi(struct pci_dev *dev) 598 { 599 pci_msi_quirk = 1; 600 printk(KERN_WARNING "PCI: MSI quirk detected. pci_msi_quirk set.\n"); 601 } 602 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_svw_msi ); 603 #endif /* CONFIG_X86_IO_APIC */ 604 605 606 /* 607 * FIXME: it is questionable that quirk_via_acpi 608 * is needed. It shows up as an ISA bridge, and does not 609 * support the PCI_INTERRUPT_LINE register at all. Therefore 610 * it seems like setting the pci_dev's 'irq' to the 611 * value of the ACPI SCI interrupt is only done for convenience. 612 * -jgarzik 613 */ 614 static void __devinit quirk_via_acpi(struct pci_dev *d) 615 { 616 /* 617 * VIA ACPI device: SCI IRQ line in PCI config byte 0x42 618 */ 619 u8 irq; 620 pci_read_config_byte(d, 0x42, &irq); 621 irq &= 0xf; 622 if (irq && (irq != 2)) 623 d->irq = irq; 624 } 625 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi ); 626 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi ); 627 628 /* 629 * Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip 630 * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature: 631 * when written, it makes an internal connection to the PIC. 632 * For these devices, this register is defined to be 4 bits wide. 633 * Normally this is fine. However for IO-APIC motherboards, or 634 * non-x86 architectures (yes Via exists on PPC among other places), 635 * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get 636 * interrupts delivered properly. 637 */ 638 static void quirk_via_irq(struct pci_dev *dev) 639 { 640 u8 irq, new_irq; 641 642 new_irq = dev->irq & 0xf; 643 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); 644 if (new_irq != irq) { 645 printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n", 646 pci_name(dev), irq, new_irq); 647 udelay(15); /* unknown if delay really needed */ 648 pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); 649 } 650 } 651 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq); 652 653 /* 654 * VIA VT82C598 has its device ID settable and many BIOSes 655 * set it to the ID of VT82C597 for backward compatibility. 656 * We need to switch it off to be able to recognize the real 657 * type of the chip. 658 */ 659 static void __devinit quirk_vt82c598_id(struct pci_dev *dev) 660 { 661 pci_write_config_byte(dev, 0xfc, 0); 662 pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); 663 } 664 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id ); 665 666 /* 667 * CardBus controllers have a legacy base address that enables them 668 * to respond as i82365 pcmcia controllers. We don't want them to 669 * do this even if the Linux CardBus driver is not loaded, because 670 * the Linux i82365 driver does not (and should not) handle CardBus. 671 */ 672 static void __devinit quirk_cardbus_legacy(struct pci_dev *dev) 673 { 674 if ((PCI_CLASS_BRIDGE_CARDBUS << 8) ^ dev->class) 675 return; 676 pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); 677 } 678 DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy); 679 680 /* 681 * Following the PCI ordering rules is optional on the AMD762. I'm not 682 * sure what the designers were smoking but let's not inhale... 683 * 684 * To be fair to AMD, it follows the spec by default, its BIOS people 685 * who turn it off! 686 */ 687 static void __devinit quirk_amd_ordering(struct pci_dev *dev) 688 { 689 u32 pcic; 690 pci_read_config_dword(dev, 0x4C, &pcic); 691 if ((pcic&6)!=6) { 692 pcic |= 6; 693 printk(KERN_WARNING "BIOS failed to enable PCI standards compliance, fixing this error.\n"); 694 pci_write_config_dword(dev, 0x4C, pcic); 695 pci_read_config_dword(dev, 0x84, &pcic); 696 pcic |= (1<<23); /* Required in this mode */ 697 pci_write_config_dword(dev, 0x84, pcic); 698 } 699 } 700 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering ); 701 702 /* 703 * DreamWorks provided workaround for Dunord I-3000 problem 704 * 705 * This card decodes and responds to addresses not apparently 706 * assigned to it. We force a larger allocation to ensure that 707 * nothing gets put too close to it. 708 */ 709 static void __devinit quirk_dunord ( struct pci_dev * dev ) 710 { 711 struct resource *r = &dev->resource [1]; 712 r->start = 0; 713 r->end = 0xffffff; 714 } 715 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord ); 716 717 /* 718 * i82380FB mobile docking controller: its PCI-to-PCI bridge 719 * is subtractive decoding (transparent), and does indicate this 720 * in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80 721 * instead of 0x01. 722 */ 723 static void __devinit quirk_transparent_bridge(struct pci_dev *dev) 724 { 725 dev->transparent = 1; 726 } 727 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge ); 728 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge ); 729 730 /* 731 * Common misconfiguration of the MediaGX/Geode PCI master that will 732 * reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 733 * datasheets found at http://www.national.com/ds/GX for info on what 734 * these bits do. <christer@weinigel.se> 735 */ 736 static void __init quirk_mediagx_master(struct pci_dev *dev) 737 { 738 u8 reg; 739 pci_read_config_byte(dev, 0x41, ®); 740 if (reg & 2) { 741 reg &= ~2; 742 printk(KERN_INFO "PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg); 743 pci_write_config_byte(dev, 0x41, reg); 744 } 745 } 746 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master ); 747 748 /* 749 * As per PCI spec, ignore base address registers 0-3 of the IDE controllers 750 * running in Compatible mode (bits 0 and 2 in the ProgIf for primary and 751 * secondary channels respectively). If the device reports Compatible mode 752 * but does use BAR0-3 for address decoding, we assume that firmware has 753 * programmed these BARs with standard values (0x1f0,0x3f4 and 0x170,0x374). 754 * Exceptions (if they exist) must be handled in chip/architecture specific 755 * fixups. 756 * 757 * Note: for non x86 people. You may need an arch specific quirk to handle 758 * moving IDE devices to native mode as well. Some plug in card devices power 759 * up in compatible mode and assume the BIOS will adjust them. 760 * 761 * Q: should we load the 0x1f0,0x3f4 into the registers or zap them as 762 * we do now ? We don't want is pci_enable_device to come along 763 * and assign new resources. Both approaches work for that. 764 */ 765 static void __devinit quirk_ide_bases(struct pci_dev *dev) 766 { 767 struct resource *res; 768 int first_bar = 2, last_bar = 0; 769 770 if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE) 771 return; 772 773 res = &dev->resource[0]; 774 775 /* primary channel: ProgIf bit 0, BAR0, BAR1 */ 776 if (!(dev->class & 1) && (res[0].flags || res[1].flags)) { 777 res[0].start = res[0].end = res[0].flags = 0; 778 res[1].start = res[1].end = res[1].flags = 0; 779 first_bar = 0; 780 last_bar = 1; 781 } 782 783 /* secondary channel: ProgIf bit 2, BAR2, BAR3 */ 784 if (!(dev->class & 4) && (res[2].flags || res[3].flags)) { 785 res[2].start = res[2].end = res[2].flags = 0; 786 res[3].start = res[3].end = res[3].flags = 0; 787 last_bar = 3; 788 } 789 790 if (!last_bar) 791 return; 792 793 printk(KERN_INFO "PCI: Ignoring BAR%d-%d of IDE controller %s\n", 794 first_bar, last_bar, pci_name(dev)); 795 } 796 DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_ide_bases); 797 798 /* 799 * Ensure C0 rev restreaming is off. This is normally done by 800 * the BIOS but in the odd case it is not the results are corruption 801 * hence the presence of a Linux check 802 */ 803 static void __init quirk_disable_pxb(struct pci_dev *pdev) 804 { 805 u16 config; 806 u8 rev; 807 808 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); 809 if (rev != 0x04) /* Only C0 requires this */ 810 return; 811 pci_read_config_word(pdev, 0x40, &config); 812 if (config & (1<<6)) { 813 config &= ~(1<<6); 814 pci_write_config_word(pdev, 0x40, config); 815 printk(KERN_INFO "PCI: C0 revision 450NX. Disabling PCI restreaming.\n"); 816 } 817 } 818 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb ); 819 820 821 /* 822 * Serverworks CSB5 IDE does not fully support native mode 823 */ 824 static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev) 825 { 826 u8 prog; 827 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 828 if (prog & 5) { 829 prog &= ~5; 830 pdev->class &= ~5; 831 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 832 /* need to re-assign BARs for compat mode */ 833 quirk_ide_bases(pdev); 834 } 835 } 836 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide ); 837 838 /* 839 * Intel 82801CAM ICH3-M datasheet says IDE modes must be the same 840 */ 841 static void __init quirk_ide_samemode(struct pci_dev *pdev) 842 { 843 u8 prog; 844 845 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 846 847 if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { 848 printk(KERN_INFO "PCI: IDE mode mismatch; forcing legacy mode\n"); 849 prog &= ~5; 850 pdev->class &= ~5; 851 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 852 /* need to re-assign BARs for compat mode */ 853 quirk_ide_bases(pdev); 854 } 855 } 856 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); 857 858 /* This was originally an Alpha specific thing, but it really fits here. 859 * The i82375 PCI/EISA bridge appears as non-classified. Fix that. 860 */ 861 static void __init quirk_eisa_bridge(struct pci_dev *dev) 862 { 863 dev->class = PCI_CLASS_BRIDGE_EISA << 8; 864 } 865 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge ); 866 867 /* 868 * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge 869 * is not activated. The myth is that Asus said that they do not want the 870 * users to be irritated by just another PCI Device in the Win98 device 871 * manager. (see the file prog/hotplug/README.p4b in the lm_sensors 872 * package 2.7.0 for details) 873 * 874 * The SMBus PCI Device can be activated by setting a bit in the ICH LPC 875 * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it 876 * becomes necessary to do this tweak in two steps -- I've chosen the Host 877 * bridge as trigger. 878 */ 879 static int __initdata asus_hides_smbus = 0; 880 881 static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev) 882 { 883 if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 884 if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) 885 switch(dev->subsystem_device) { 886 case 0x8025: /* P4B-LX */ 887 case 0x8070: /* P4B */ 888 case 0x8088: /* P4B533 */ 889 case 0x1626: /* L3C notebook */ 890 asus_hides_smbus = 1; 891 } 892 if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) 893 switch(dev->subsystem_device) { 894 case 0x80b1: /* P4GE-V */ 895 case 0x80b2: /* P4PE */ 896 case 0x8093: /* P4B533-V */ 897 asus_hides_smbus = 1; 898 } 899 if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) 900 switch(dev->subsystem_device) { 901 case 0x8030: /* P4T533 */ 902 asus_hides_smbus = 1; 903 } 904 if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) 905 switch (dev->subsystem_device) { 906 case 0x8070: /* P4G8X Deluxe */ 907 asus_hides_smbus = 1; 908 } 909 if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 910 switch (dev->subsystem_device) { 911 case 0x1751: /* M2N notebook */ 912 case 0x1821: /* M5N notebook */ 913 asus_hides_smbus = 1; 914 } 915 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 916 switch (dev->subsystem_device) { 917 case 0x184b: /* W1N notebook */ 918 case 0x186a: /* M6Ne notebook */ 919 asus_hides_smbus = 1; 920 } 921 if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) { 922 switch (dev->subsystem_device) { 923 case 0x1882: /* M6V notebook */ 924 asus_hides_smbus = 1; 925 } 926 } 927 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { 928 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 929 switch(dev->subsystem_device) { 930 case 0x088C: /* HP Compaq nc8000 */ 931 case 0x0890: /* HP Compaq nc6000 */ 932 asus_hides_smbus = 1; 933 } 934 if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 935 switch (dev->subsystem_device) { 936 case 0x12bc: /* HP D330L */ 937 case 0x12bd: /* HP D530 */ 938 asus_hides_smbus = 1; 939 } 940 if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) { 941 switch (dev->subsystem_device) { 942 case 0x099c: /* HP Compaq nx6110 */ 943 asus_hides_smbus = 1; 944 } 945 } 946 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_TOSHIBA)) { 947 if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 948 switch(dev->subsystem_device) { 949 case 0x0001: /* Toshiba Satellite A40 */ 950 asus_hides_smbus = 1; 951 } 952 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 953 switch(dev->subsystem_device) { 954 case 0x0001: /* Toshiba Tecra M2 */ 955 asus_hides_smbus = 1; 956 } 957 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { 958 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 959 switch(dev->subsystem_device) { 960 case 0xC00C: /* Samsung P35 notebook */ 961 asus_hides_smbus = 1; 962 } 963 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { 964 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 965 switch(dev->subsystem_device) { 966 case 0x0058: /* Compaq Evo N620c */ 967 asus_hides_smbus = 1; 968 } 969 } 970 } 971 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge ); 972 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge ); 973 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge ); 974 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge ); 975 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge ); 976 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge ); 977 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge ); 978 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge ); 979 980 static void __init asus_hides_smbus_lpc(struct pci_dev *dev) 981 { 982 u16 val; 983 984 if (likely(!asus_hides_smbus)) 985 return; 986 987 pci_read_config_word(dev, 0xF2, &val); 988 if (val & 0x8) { 989 pci_write_config_word(dev, 0xF2, val & (~0x8)); 990 pci_read_config_word(dev, 0xF2, &val); 991 if (val & 0x8) 992 printk(KERN_INFO "PCI: i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val); 993 else 994 printk(KERN_INFO "PCI: Enabled i801 SMBus device\n"); 995 } 996 } 997 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc ); 998 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc ); 999 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc ); 1000 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc ); 1001 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc ); 1002 1003 static void __init asus_hides_smbus_lpc_ich6(struct pci_dev *dev) 1004 { 1005 u32 val, rcba; 1006 void __iomem *base; 1007 1008 if (likely(!asus_hides_smbus)) 1009 return; 1010 pci_read_config_dword(dev, 0xF0, &rcba); 1011 base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000); /* use bits 31:14, 16 kB aligned */ 1012 if (base == NULL) return; 1013 val=readl(base + 0x3418); /* read the Function Disable register, dword mode only */ 1014 writel(val & 0xFFFFFFF7, base + 0x3418); /* enable the SMBus device */ 1015 iounmap(base); 1016 printk(KERN_INFO "PCI: Enabled ICH6/i801 SMBus device\n"); 1017 } 1018 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6 ); 1019 1020 /* 1021 * SiS 96x south bridge: BIOS typically hides SMBus device... 1022 */ 1023 static void __init quirk_sis_96x_smbus(struct pci_dev *dev) 1024 { 1025 u8 val = 0; 1026 printk(KERN_INFO "Enabling SiS 96x SMBus.\n"); 1027 pci_read_config_byte(dev, 0x77, &val); 1028 pci_write_config_byte(dev, 0x77, val & ~0x10); 1029 pci_read_config_byte(dev, 0x77, &val); 1030 } 1031 1032 /* 1033 * ... This is further complicated by the fact that some SiS96x south 1034 * bridges pretend to be 85C503/5513 instead. In that case see if we 1035 * spotted a compatible north bridge to make sure. 1036 * (pci_find_device doesn't work yet) 1037 * 1038 * We can also enable the sis96x bit in the discovery register.. 1039 */ 1040 static int __devinitdata sis_96x_compatible = 0; 1041 1042 #define SIS_DETECT_REGISTER 0x40 1043 1044 static void __init quirk_sis_503(struct pci_dev *dev) 1045 { 1046 u8 reg; 1047 u16 devid; 1048 1049 pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); 1050 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); 1051 pci_read_config_word(dev, PCI_DEVICE_ID, &devid); 1052 if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { 1053 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); 1054 return; 1055 } 1056 1057 /* Make people aware that we changed the config.. */ 1058 printk(KERN_WARNING "Uncovering SIS%x that hid as a SIS503 (compatible=%d)\n", devid, sis_96x_compatible); 1059 1060 /* 1061 * Ok, it now shows up as a 96x.. The 96x quirks are after 1062 * the 503 quirk in the quirk table, so they'll automatically 1063 * run and enable things like the SMBus device 1064 */ 1065 dev->device = devid; 1066 } 1067 1068 static void __init quirk_sis_96x_compatible(struct pci_dev *dev) 1069 { 1070 sis_96x_compatible = 1; 1071 } 1072 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_645, quirk_sis_96x_compatible ); 1073 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_646, quirk_sis_96x_compatible ); 1074 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_648, quirk_sis_96x_compatible ); 1075 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_650, quirk_sis_96x_compatible ); 1076 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_651, quirk_sis_96x_compatible ); 1077 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_735, quirk_sis_96x_compatible ); 1078 1079 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503 ); 1080 /* 1081 * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller 1082 * and MC97 modem controller are disabled when a second PCI soundcard is 1083 * present. This patch, tweaking the VT8237 ISA bridge, enables them. 1084 * -- bjd 1085 */ 1086 static void __init asus_hides_ac97_lpc(struct pci_dev *dev) 1087 { 1088 u8 val; 1089 int asus_hides_ac97 = 0; 1090 1091 if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1092 if (dev->device == PCI_DEVICE_ID_VIA_8237) 1093 asus_hides_ac97 = 1; 1094 } 1095 1096 if (!asus_hides_ac97) 1097 return; 1098 1099 pci_read_config_byte(dev, 0x50, &val); 1100 if (val & 0xc0) { 1101 pci_write_config_byte(dev, 0x50, val & (~0xc0)); 1102 pci_read_config_byte(dev, 0x50, &val); 1103 if (val & 0xc0) 1104 printk(KERN_INFO "PCI: onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", val); 1105 else 1106 printk(KERN_INFO "PCI: enabled onboard AC97/MC97 devices\n"); 1107 } 1108 } 1109 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc ); 1110 1111 1112 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus ); 1113 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus ); 1114 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus ); 1115 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus ); 1116 1117 #ifdef CONFIG_X86_IO_APIC 1118 static void __init quirk_alder_ioapic(struct pci_dev *pdev) 1119 { 1120 int i; 1121 1122 if ((pdev->class >> 8) != 0xff00) 1123 return; 1124 1125 /* the first BAR is the location of the IO APIC...we must 1126 * not touch this (and it's already covered by the fixmap), so 1127 * forcibly insert it into the resource tree */ 1128 if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) 1129 insert_resource(&iomem_resource, &pdev->resource[0]); 1130 1131 /* The next five BARs all seem to be rubbish, so just clean 1132 * them out */ 1133 for (i=1; i < 6; i++) { 1134 memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); 1135 } 1136 1137 } 1138 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic ); 1139 #endif 1140 1141 enum ide_combined_type { COMBINED = 0, IDE = 1, LIBATA = 2 }; 1142 /* Defaults to combined */ 1143 static enum ide_combined_type combined_mode; 1144 1145 static int __init combined_setup(char *str) 1146 { 1147 if (!strncmp(str, "ide", 3)) 1148 combined_mode = IDE; 1149 else if (!strncmp(str, "libata", 6)) 1150 combined_mode = LIBATA; 1151 else /* "combined" or anything else defaults to old behavior */ 1152 combined_mode = COMBINED; 1153 1154 return 1; 1155 } 1156 __setup("combined_mode=", combined_setup); 1157 1158 #ifdef CONFIG_SCSI_SATA_INTEL_COMBINED 1159 static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev) 1160 { 1161 u8 prog, comb, tmp; 1162 int ich = 0; 1163 1164 /* 1165 * Narrow down to Intel SATA PCI devices. 1166 */ 1167 switch (pdev->device) { 1168 /* PCI ids taken from drivers/scsi/ata_piix.c */ 1169 case 0x24d1: 1170 case 0x24df: 1171 case 0x25a3: 1172 case 0x25b0: 1173 ich = 5; 1174 break; 1175 case 0x2651: 1176 case 0x2652: 1177 case 0x2653: 1178 case 0x2680: /* ESB2 */ 1179 ich = 6; 1180 break; 1181 case 0x27c0: 1182 case 0x27c4: 1183 ich = 7; 1184 break; 1185 case 0x2828: /* ICH8M */ 1186 ich = 8; 1187 break; 1188 default: 1189 /* we do not handle this PCI device */ 1190 return; 1191 } 1192 1193 /* 1194 * Read combined mode register. 1195 */ 1196 pci_read_config_byte(pdev, 0x90, &tmp); /* combined mode reg */ 1197 1198 if (ich == 5) { 1199 tmp &= 0x6; /* interesting bits 2:1, PATA primary/secondary */ 1200 if (tmp == 0x4) /* bits 10x */ 1201 comb = (1 << 0); /* SATA port 0, PATA port 1 */ 1202 else if (tmp == 0x6) /* bits 11x */ 1203 comb = (1 << 2); /* PATA port 0, SATA port 1 */ 1204 else 1205 return; /* not in combined mode */ 1206 } else { 1207 WARN_ON((ich != 6) && (ich != 7) && (ich != 8)); 1208 tmp &= 0x3; /* interesting bits 1:0 */ 1209 if (tmp & (1 << 0)) 1210 comb = (1 << 2); /* PATA port 0, SATA port 1 */ 1211 else if (tmp & (1 << 1)) 1212 comb = (1 << 0); /* SATA port 0, PATA port 1 */ 1213 else 1214 return; /* not in combined mode */ 1215 } 1216 1217 /* 1218 * Read programming interface register. 1219 * (Tells us if it's legacy or native mode) 1220 */ 1221 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1222 1223 /* if SATA port is in native mode, we're ok. */ 1224 if (prog & comb) 1225 return; 1226 1227 /* Don't reserve any so the IDE driver can get them (but only if 1228 * combined_mode=ide). 1229 */ 1230 if (combined_mode == IDE) 1231 return; 1232 1233 /* Grab them both for libata if combined_mode=libata. */ 1234 if (combined_mode == LIBATA) { 1235 request_region(0x1f0, 8, "libata"); /* port 0 */ 1236 request_region(0x170, 8, "libata"); /* port 1 */ 1237 return; 1238 } 1239 1240 /* SATA port is in legacy mode. Reserve port so that 1241 * IDE driver does not attempt to use it. If request_region 1242 * fails, it will be obvious at boot time, so we don't bother 1243 * checking return values. 1244 */ 1245 if (comb == (1 << 0)) 1246 request_region(0x1f0, 8, "libata"); /* port 0 */ 1247 else 1248 request_region(0x170, 8, "libata"); /* port 1 */ 1249 } 1250 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_intel_ide_combined ); 1251 #endif /* CONFIG_SCSI_SATA_INTEL_COMBINED */ 1252 1253 1254 int pcie_mch_quirk; 1255 1256 static void __devinit quirk_pcie_mch(struct pci_dev *pdev) 1257 { 1258 pcie_mch_quirk = 1; 1259 } 1260 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch ); 1261 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch ); 1262 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch ); 1263 1264 1265 /* 1266 * It's possible for the MSI to get corrupted if shpc and acpi 1267 * are used together on certain PXH-based systems. 1268 */ 1269 static void __devinit quirk_pcie_pxh(struct pci_dev *dev) 1270 { 1271 disable_msi_mode(dev, pci_find_capability(dev, PCI_CAP_ID_MSI), 1272 PCI_CAP_ID_MSI); 1273 dev->no_msi = 1; 1274 1275 printk(KERN_WARNING "PCI: PXH quirk detected, " 1276 "disabling MSI for SHPC device\n"); 1277 } 1278 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); 1279 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); 1280 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); 1281 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); 1282 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); 1283 1284 1285 /* 1286 * Fixup the cardbus bridges on the IBM Dock II docking station 1287 */ 1288 static void __devinit quirk_ibm_dock2_cardbus(struct pci_dev *dev) 1289 { 1290 u32 val; 1291 1292 /* 1293 * tie the 2 interrupt pins to INTA, and configure the 1294 * multifunction routing register to handle this. 1295 */ 1296 if ((dev->subsystem_vendor == PCI_VENDOR_ID_IBM) && 1297 (dev->subsystem_device == 0x0148)) { 1298 printk(KERN_INFO "PCI: Found IBM Dock II Cardbus Bridge " 1299 "applying quirk\n"); 1300 pci_read_config_dword(dev, 0x8c, &val); 1301 val = ((val & 0xffffff00) | 0x1002); 1302 pci_write_config_dword(dev, 0x8c, val); 1303 pci_read_config_dword(dev, 0x80, &val); 1304 val = ((val & 0x00ffff00) | 0x2864c077); 1305 pci_write_config_dword(dev, 0x80, val); 1306 } 1307 } 1308 1309 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1420, 1310 quirk_ibm_dock2_cardbus); 1311 1312 static void __devinit quirk_netmos(struct pci_dev *dev) 1313 { 1314 unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; 1315 unsigned int num_serial = dev->subsystem_device & 0xf; 1316 1317 /* 1318 * These Netmos parts are multiport serial devices with optional 1319 * parallel ports. Even when parallel ports are present, they 1320 * are identified as class SERIAL, which means the serial driver 1321 * will claim them. To prevent this, mark them as class OTHER. 1322 * These combo devices should be claimed by parport_serial. 1323 * 1324 * The subdevice ID is of the form 0x00PS, where <P> is the number 1325 * of parallel ports and <S> is the number of serial ports. 1326 */ 1327 switch (dev->device) { 1328 case PCI_DEVICE_ID_NETMOS_9735: 1329 case PCI_DEVICE_ID_NETMOS_9745: 1330 case PCI_DEVICE_ID_NETMOS_9835: 1331 case PCI_DEVICE_ID_NETMOS_9845: 1332 case PCI_DEVICE_ID_NETMOS_9855: 1333 if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL && 1334 num_parallel) { 1335 printk(KERN_INFO "PCI: Netmos %04x (%u parallel, " 1336 "%u serial); changing class SERIAL to OTHER " 1337 "(use parport_serial)\n", 1338 dev->device, num_parallel, num_serial); 1339 dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | 1340 (dev->class & 0xff); 1341 } 1342 } 1343 } 1344 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos); 1345 1346 1347 static void __devinit fixup_rev1_53c810(struct pci_dev* dev) 1348 { 1349 /* rev 1 ncr53c810 chips don't set the class at all which means 1350 * they don't get their resources remapped. Fix that here. 1351 */ 1352 1353 if (dev->class == PCI_CLASS_NOT_DEFINED) { 1354 printk(KERN_INFO "NCR 53c810 rev 1 detected, setting PCI class.\n"); 1355 dev->class = PCI_CLASS_STORAGE_SCSI; 1356 } 1357 } 1358 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); 1359 1360 1361 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) 1362 { 1363 while (f < end) { 1364 if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) && 1365 (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) { 1366 pr_debug("PCI: Calling quirk %p for %s\n", f->hook, pci_name(dev)); 1367 f->hook(dev); 1368 } 1369 f++; 1370 } 1371 } 1372 1373 extern struct pci_fixup __start_pci_fixups_early[]; 1374 extern struct pci_fixup __end_pci_fixups_early[]; 1375 extern struct pci_fixup __start_pci_fixups_header[]; 1376 extern struct pci_fixup __end_pci_fixups_header[]; 1377 extern struct pci_fixup __start_pci_fixups_final[]; 1378 extern struct pci_fixup __end_pci_fixups_final[]; 1379 extern struct pci_fixup __start_pci_fixups_enable[]; 1380 extern struct pci_fixup __end_pci_fixups_enable[]; 1381 1382 1383 void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) 1384 { 1385 struct pci_fixup *start, *end; 1386 1387 switch(pass) { 1388 case pci_fixup_early: 1389 start = __start_pci_fixups_early; 1390 end = __end_pci_fixups_early; 1391 break; 1392 1393 case pci_fixup_header: 1394 start = __start_pci_fixups_header; 1395 end = __end_pci_fixups_header; 1396 break; 1397 1398 case pci_fixup_final: 1399 start = __start_pci_fixups_final; 1400 end = __end_pci_fixups_final; 1401 break; 1402 1403 case pci_fixup_enable: 1404 start = __start_pci_fixups_enable; 1405 end = __end_pci_fixups_enable; 1406 break; 1407 1408 default: 1409 /* stupid compiler warning, you would think with an enum... */ 1410 return; 1411 } 1412 pci_do_fixups(dev, start, end); 1413 } 1414 1415 /* Enable 1k I/O space granularity on the Intel P64H2 */ 1416 static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev) 1417 { 1418 u16 en1k; 1419 u8 io_base_lo, io_limit_lo; 1420 unsigned long base, limit; 1421 struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES; 1422 1423 pci_read_config_word(dev, 0x40, &en1k); 1424 1425 if (en1k & 0x200) { 1426 printk(KERN_INFO "PCI: Enable I/O Space to 1 KB Granularity\n"); 1427 1428 pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo); 1429 pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo); 1430 base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; 1431 limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; 1432 1433 if (base <= limit) { 1434 res->start = base; 1435 res->end = limit + 0x3ff; 1436 } 1437 } 1438 } 1439 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); 1440 1441 EXPORT_SYMBOL(pcie_mch_quirk); 1442 #ifdef CONFIG_HOTPLUG 1443 EXPORT_SYMBOL(pci_fixup_device); 1444 #endif 1445