1# 2# For a description of the syntax of this configuration file, 3# see Documentation/kbuild/kconfig-language.txt. 4# 5config M68K 6 bool 7 default y 8 9config MMU 10 bool 11 default y 12 13config UID16 14 bool 15 default y 16 17config RWSEM_GENERIC_SPINLOCK 18 bool 19 default y 20 21config RWSEM_XCHGADD_ALGORITHM 22 bool 23 24config GENERIC_CALIBRATE_DELAY 25 bool 26 default y 27 28mainmenu "Linux/68k Kernel Configuration" 29 30source "init/Kconfig" 31 32menu "Platform dependent setup" 33 34config EISA 35 bool 36 ---help--- 37 The Extended Industry Standard Architecture (EISA) bus was 38 developed as an open alternative to the IBM MicroChannel bus. 39 40 The EISA bus provided some of the features of the IBM MicroChannel 41 bus while maintaining backward compatibility with cards made for 42 the older ISA bus. The EISA bus saw limited use between 1988 and 43 1995 when it was made obsolete by the PCI bus. 44 45 Say Y here if you are building a kernel for an EISA-based machine. 46 47 Otherwise, say N. 48 49config MCA 50 bool 51 help 52 MicroChannel Architecture is found in some IBM PS/2 machines and 53 laptops. It is a bus system similar to PCI or ISA. See 54 <file:Documentation/mca.txt> (and especially the web page given 55 there) before attempting to build an MCA bus kernel. 56 57config PCMCIA 58 tristate 59 ---help--- 60 Say Y here if you want to attach PCMCIA- or PC-cards to your Linux 61 computer. These are credit-card size devices such as network cards, 62 modems or hard drives often used with laptops computers. There are 63 actually two varieties of these cards: the older 16 bit PCMCIA cards 64 and the newer 32 bit CardBus cards. If you want to use CardBus 65 cards, you need to say Y here and also to "CardBus support" below. 66 67 To use your PC-cards, you will need supporting software from David 68 Hinds' pcmcia-cs package (see the file <file:Documentation/Changes> 69 for location). Please also read the PCMCIA-HOWTO, available from 70 <http://www.tldp.org/docs.html#howto>. 71 72 To compile this driver as modules, choose M here: the 73 modules will be called pcmcia_core and ds. 74 75config SUN3 76 bool "Sun3 support" 77 select M68020 78 select MMU_SUN3 if MMU 79 help 80 This option enables support for the Sun 3 series of workstations 81 (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires 82 that all other hardware types must be disabled, as Sun 3 kernels 83 are incompatible with all other m68k targets (including Sun 3x!). 84 85 If you don't want to compile a kernel exclusively for a Sun 3, say N. 86 87config AMIGA 88 bool "Amiga support" 89 depends on !MMU_SUN3 90 help 91 This option enables support for the Amiga series of computers. If 92 you plan to use this kernel on an Amiga, say Y here and browse the 93 material available in <file:Documentation/m68k>; otherwise say N. 94 95config ATARI 96 bool "Atari support" 97 depends on !MMU_SUN3 98 help 99 This option enables support for the 68000-based Atari series of 100 computers (including the TT, Falcon and Medusa). If you plan to use 101 this kernel on an Atari, say Y here and browse the material 102 available in <file:Documentation/m68k>; otherwise say N. 103 104config HADES 105 bool "Hades support" 106 depends on ATARI && BROKEN 107 help 108 This option enables support for the Hades Atari clone. If you plan 109 to use this kernel on a Hades, say Y here; otherwise say N. 110 111config PCI 112 bool 113 depends on HADES 114 default y 115 help 116 Find out whether you have a PCI motherboard. PCI is the name of a 117 bus system, i.e. the way the CPU talks to the other stuff inside 118 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or 119 VESA. If you have PCI, say Y, otherwise N. 120 121 The PCI-HOWTO, available from 122 <http://www.tldp.org/docs.html#howto>, contains valuable 123 information about which PCI hardware does work under Linux and which 124 doesn't. 125 126config MAC 127 bool "Macintosh support" 128 depends on !MMU_SUN3 129 help 130 This option enables support for the Apple Macintosh series of 131 computers (yes, there is experimental support now, at least for part 132 of the series). 133 134 Say N unless you're willing to code the remaining necessary support. 135 ;) 136 137config NUBUS 138 bool 139 depends on MAC 140 default y 141 142config M68K_L2_CACHE 143 bool 144 depends on MAC 145 default y 146 147config APOLLO 148 bool "Apollo support" 149 depends on !MMU_SUN3 150 help 151 Say Y here if you want to run Linux on an MC680x0-based Apollo 152 Domain workstation such as the DN3500. 153 154config VME 155 bool "VME (Motorola and BVM) support" 156 depends on !MMU_SUN3 157 help 158 Say Y here if you want to build a kernel for a 680x0 based VME 159 board. Boards currently supported include Motorola boards MVME147, 160 MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and 161 BVME6000 boards from BVM Ltd are also supported. 162 163config MVME147 164 bool "MVME147 support" 165 depends on VME 166 help 167 Say Y to include support for early Motorola VME boards. This will 168 build a kernel which can run on MVME147 single-board computers. If 169 you select this option you will have to select the appropriate 170 drivers for SCSI, Ethernet and serial ports later on. 171 172config MVME16x 173 bool "MVME162, 166 and 167 support" 174 depends on VME 175 help 176 Say Y to include support for Motorola VME boards. This will build a 177 kernel which can run on MVME162, MVME166, MVME167, MVME172, and 178 MVME177 boards. If you select this option you will have to select 179 the appropriate drivers for SCSI, Ethernet and serial ports later 180 on. 181 182config BVME6000 183 bool "BVME4000 and BVME6000 support" 184 depends on VME 185 help 186 Say Y to include support for VME boards from BVM Ltd. This will 187 build a kernel which can run on BVME4000 and BVME6000 boards. If 188 you select this option you will have to select the appropriate 189 drivers for SCSI, Ethernet and serial ports later on. 190 191config HP300 192 bool "HP9000/300 and HP9000/400 support" 193 depends on !MMU_SUN3 194 help 195 This option enables support for the HP9000/300 and HP9000/400 series 196 of workstations. Support for these machines is still somewhat 197 experimental. If you plan to try to use the kernel on such a machine 198 say Y here. 199 Everybody else says N. 200 201config DIO 202 bool "DIO bus support" 203 depends on HP300 204 default y 205 help 206 Say Y here to enable support for the "DIO" expansion bus used in 207 HP300 machines. If you are using such a system you almost certainly 208 want this. 209 210config SUN3X 211 bool "Sun3x support" 212 depends on !MMU_SUN3 213 select M68030 214 help 215 This option enables support for the Sun 3x series of workstations. 216 Be warned that this support is very experimental. 217 Note that Sun 3x kernels are not compatible with Sun 3 hardware. 218 General Linux information on the Sun 3x series (now discontinued) 219 is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. 220 221 If you don't want to compile a kernel for a Sun 3x, say N. 222 223config Q40 224 bool "Q40/Q60 support" 225 depends on !MMU_SUN3 226 help 227 The Q40 is a Motorola 68040-based successor to the Sinclair QL 228 manufactured in Germany. There is an official Q40 home page at 229 <http://www.q40.de/>. This option enables support for the Q40 and 230 Q60. Select your CPU below. For 68LC060 don't forget to enable FPU 231 emulation. 232 233comment "Processor type" 234 235config M68020 236 bool "68020 support" 237 help 238 If you anticipate running this kernel on a computer with a MC68020 239 processor, say Y. Otherwise, say N. Note that the 68020 requires a 240 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the 241 Sun 3, which provides its own version. 242 243config M68030 244 bool "68030 support" 245 depends on !MMU_SUN3 246 help 247 If you anticipate running this kernel on a computer with a MC68030 248 processor, say Y. Otherwise, say N. Note that a MC68EC030 will not 249 work, as it does not include an MMU (Memory Management Unit). 250 251config M68040 252 bool "68040 support" 253 depends on !MMU_SUN3 254 help 255 If you anticipate running this kernel on a computer with a MC68LC040 256 or MC68040 processor, say Y. Otherwise, say N. Note that an 257 MC68EC040 will not work, as it does not include an MMU (Memory 258 Management Unit). 259 260config M68060 261 bool "68060 support" 262 depends on !MMU_SUN3 263 help 264 If you anticipate running this kernel on a computer with a MC68060 265 processor, say Y. Otherwise, say N. 266 267config MMU_MOTOROLA 268 bool 269 depends on MMU && !MMU_SUN3 270 default y 271 272config MMU_SUN3 273 bool 274 275config M68KFPU_EMU 276 bool "Math emulation support (EXPERIMENTAL)" 277 depends on EXPERIMENTAL 278 help 279 At some point in the future, this will cause floating-point math 280 instructions to be emulated by the kernel on machines that lack a 281 floating-point math coprocessor. Thrill-seekers and chronically 282 sleep-deprived psychotic hacker types can say Y now, everyone else 283 should probably wait a while. 284 285config M68KFPU_EMU_EXTRAPREC 286 bool "Math emulation extra precision" 287 depends on M68KFPU_EMU 288 help 289 The fpu uses normally a few bit more during calculations for 290 correct rounding, the emulator can (often) do the same but this 291 extra calculation can cost quite some time, so you can disable 292 it here. The emulator will then "only" calculate with a 64 bit 293 mantissa and round slightly incorrect, what is more then enough 294 for normal usage. 295 296config M68KFPU_EMU_ONLY 297 bool "Math emulation only kernel" 298 depends on M68KFPU_EMU 299 help 300 This option prevents any floating-point instructions from being 301 compiled into the kernel, thereby the kernel doesn't save any 302 floating point context anymore during task switches, so this 303 kernel will only be usable on machines without a floating-point 304 math coprocessor. This makes the kernel a bit faster as no tests 305 needs to be executed whether a floating-point instruction in the 306 kernel should be executed or not. 307 308config ADVANCED 309 bool "Advanced configuration options" 310 ---help--- 311 This gives you access to some advanced options for the CPU. The 312 defaults should be fine for most users, but these options may make 313 it possible for you to improve performance somewhat if you know what 314 you are doing. 315 316 Note that the answer to this question won't directly affect the 317 kernel: saying N will just cause the configurator to skip all 318 the questions about these options. 319 320 Most users should say N to this question. 321 322config RMW_INSNS 323 bool "Use read-modify-write instructions" 324 depends on ADVANCED 325 ---help--- 326 This allows to use certain instructions that work with indivisible 327 read-modify-write bus cycles. While this is faster than the 328 workaround of disabling interrupts, it can conflict with DMA 329 ( = direct memory access) on many Amiga systems, and it is also said 330 to destabilize other machines. It is very likely that this will 331 cause serious problems on any Amiga or Atari Medusa if set. The only 332 configuration where it should work are 68030-based Ataris, where it 333 apparently improves performance. But you've been warned! Unless you 334 really know what you are doing, say N. Try Y only if you're quite 335 adventurous. 336 337config SINGLE_MEMORY_CHUNK 338 bool "Use one physical chunk of memory only" 339 depends on ADVANCED && !SUN3 340 help 341 Ignore all but the first contiguous chunk of physical memory for VM 342 purposes. This will save a few bytes kernel size and may speed up 343 some operations. Say N if not sure. 344 345config 060_WRITETHROUGH 346 bool "Use write-through caching for 68060 supervisor accesses" 347 depends on ADVANCED && M68060 348 ---help--- 349 The 68060 generally uses copyback caching of recently accessed data. 350 Copyback caching means that memory writes will be held in an on-chip 351 cache and only written back to memory some time later. Saying Y 352 here will force supervisor (kernel) accesses to use writethrough 353 caching. Writethrough caching means that data is written to memory 354 straight away, so that cache and memory data always agree. 355 Writethrough caching is less efficient, but is needed for some 356 drivers on 68060 based systems where the 68060 bus snooping signal 357 is hardwired on. The 53c710 SCSI driver is known to suffer from 358 this problem. 359 360source "mm/Kconfig" 361 362endmenu 363 364menu "General setup" 365 366source "fs/Kconfig.binfmt" 367 368config ZORRO 369 bool "Amiga Zorro (AutoConfig) bus support" 370 depends on AMIGA 371 help 372 This enables support for the Zorro bus in the Amiga. If you have 373 expansion cards in your Amiga that conform to the Amiga 374 AutoConfig(tm) specification, say Y, otherwise N. Note that even 375 expansion cards that do not fit in the Zorro slots but fit in e.g. 376 the CPU slot may fall in this category, so you have to say Y to let 377 Linux use these. 378 379config AMIGA_PCMCIA 380 bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)" 381 depends on AMIGA && EXPERIMENTAL 382 help 383 Include support in the kernel for pcmcia on Amiga 1200 and Amiga 384 600. If you intend to use pcmcia cards say Y; otherwise say N. 385 386config STRAM_SWAP 387 bool "Support for ST-RAM as swap space" 388 depends on ATARI && BROKEN 389 ---help--- 390 Some Atari 68k machines (including the 520STF and 1020STE) divide 391 their addressable memory into ST and TT sections. The TT section 392 (up to 512MB) is the main memory; the ST section (up to 4MB) is 393 accessible to the built-in graphics board, runs slower, and is 394 present mainly for backward compatibility with older machines. 395 396 This enables support for using (parts of) ST-RAM as swap space, 397 instead of as normal system memory. This can first enhance system 398 performance if you have lots of alternate RAM (compared to the size 399 of ST-RAM), because executable code always will reside in faster 400 memory. ST-RAM will remain as ultra-fast swap space. On the other 401 hand, it allows much improved dynamic allocations of ST-RAM buffers 402 for device driver modules (e.g. floppy, ACSI, SLM printer, DMA 403 sound). The probability that such allocations at module load time 404 fail is drastically reduced. 405 406config STRAM_PROC 407 bool "ST-RAM statistics in /proc" 408 depends on ATARI 409 help 410 Say Y here to report ST-RAM usage statistics in /proc/stram. See 411 the help for CONFIG_STRAM_SWAP for discussion of ST-RAM and its 412 uses. 413 414config HEARTBEAT 415 bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40 416 default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300 417 help 418 Use the power-on LED on your machine as a load meter. The exact 419 behavior is platform-dependent, but normally the flash frequency is 420 a hyperbolic function of the 5-minute load average. 421 422# We have a dedicated heartbeat LED. :-) 423config PROC_HARDWARE 424 bool "/proc/hardware support" 425 help 426 Say Y here to support the /proc/hardware file, which gives you 427 access to information about the machine you're running on, 428 including the model, CPU, MMU, clock speed, BogoMIPS rating, 429 and memory size. 430 431config ISA 432 bool 433 depends on Q40 || AMIGA_PCMCIA || GG2 434 default y 435 help 436 Find out whether you have ISA slots on your motherboard. ISA is the 437 name of a bus system, i.e. the way the CPU talks to the other stuff 438 inside your box. Other bus systems are PCI, EISA, MicroChannel 439 (MCA) or VESA. ISA is an older system, now being displaced by PCI; 440 newer boards don't support it. If you have ISA, say Y, otherwise N. 441 442config GENERIC_ISA_DMA 443 bool 444 depends on Q40 || AMIGA_PCMCIA || GG2 445 default y 446 447source "drivers/pci/Kconfig" 448 449source "drivers/zorro/Kconfig" 450 451endmenu 452 453source "drivers/Kconfig" 454 455menu "Character devices" 456 457config ATARI_MFPSER 458 tristate "Atari MFP serial support" 459 depends on ATARI 460 ---help--- 461 If you like to use the MFP serial ports ("Modem1", "Serial1") under 462 Linux, say Y. The driver equally supports all kinds of MFP serial 463 ports and automatically detects whether Serial1 is available. 464 465 To compile this driver as a module, choose M here. 466 467 Note for Falcon users: You also have an MFP port, it's just not 468 wired to the outside... But you could use the port under Linux. 469 470config ATARI_SCC 471 tristate "Atari SCC serial support" 472 depends on ATARI 473 ---help--- 474 If you have serial ports based on a Zilog SCC chip (Modem2, Serial2, 475 LAN) and like to use them under Linux, say Y. All built-in SCC's are 476 supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have 477 two connectors for channel A (Serial2 and LAN), they are visible as 478 two separate devices. 479 480 To compile this driver as a module, choose M here. 481 482config ATARI_SCC_DMA 483 bool "Atari SCC serial DMA support" 484 depends on ATARI_SCC 485 help 486 This enables DMA support for receiving data on channel A of the SCC. 487 If you have a TT you may say Y here and read 488 drivers/char/atari_SCC.README. All other users should say N here, 489 because only the TT has SCC-DMA, even if your machine keeps claiming 490 so at boot time. 491 492config ATARI_MIDI 493 tristate "Atari MIDI serial support" 494 depends on ATARI 495 help 496 If you want to use your Atari's MIDI port in Linux, say Y. 497 498 To compile this driver as a module, choose M here. 499 500config ATARI_DSP56K 501 tristate "Atari DSP56k support (EXPERIMENTAL)" 502 depends on ATARI && EXPERIMENTAL 503 help 504 If you want to be able to use the DSP56001 in Falcons, say Y. This 505 driver is still experimental, and if you don't know what it is, or 506 if you don't have this processor, just say N. 507 508 To compile this driver as a module, choose M here. 509 510config AMIGA_BUILTIN_SERIAL 511 tristate "Amiga builtin serial support" 512 depends on AMIGA 513 help 514 If you want to use your Amiga's built-in serial port in Linux, 515 answer Y. 516 517 To compile this driver as a module, choose M here. 518 519config WHIPPET_SERIAL 520 tristate "Hisoft Whippet PCMCIA serial support" 521 depends on AMIGA_PCMCIA 522 help 523 HiSoft has a web page at <http://www.hisoft.co.uk/>, but there 524 is no listing for the Whippet in their Amiga section. 525 526config MULTIFACE_III_TTY 527 tristate "Multiface Card III serial support" 528 depends on AMIGA 529 help 530 If you want to use a Multiface III card's serial port in Linux, 531 answer Y. 532 533 To compile this driver as a module, choose M here. 534 535config GVPIOEXT 536 tristate "GVP IO-Extender support" 537 depends on PARPORT=n && ZORRO 538 help 539 If you want to use a GVP IO-Extender serial card in Linux, say Y. 540 Otherwise, say N. 541 542config GVPIOEXT_LP 543 tristate "GVP IO-Extender parallel printer support" 544 depends on GVPIOEXT 545 help 546 Say Y to enable driving a printer from the parallel port on your 547 GVP IO-Extender card, N otherwise. 548 549config GVPIOEXT_PLIP 550 tristate "GVP IO-Extender PLIP support" 551 depends on GVPIOEXT 552 help 553 Say Y to enable doing IP over the parallel port on your GVP 554 IO-Extender card, N otherwise. 555 556config MAC_SCC 557 tristate "Macintosh serial support" 558 depends on MAC 559 560config MAC_HID 561 bool 562 depends on INPUT_ADBHID 563 default y 564 565config MAC_ADBKEYCODES 566 bool "Support for ADB raw keycodes" 567 depends on INPUT_ADBHID 568 help 569 This provides support for sending raw ADB keycodes to console 570 devices. This is the default up to 2.4.0, but in future this may be 571 phased out in favor of generic Linux keycodes. If you say Y here, 572 you can dynamically switch via the 573 /proc/sys/dev/mac_hid/keyboard_sends_linux_keycodes 574 sysctl and with the "keyboard_sends_linux_keycodes=" kernel 575 argument. 576 577 If unsure, say Y here. 578 579config ADB_KEYBOARD 580 bool "Support for ADB keyboard (old driver)" 581 depends on MAC && !INPUT_ADBHID 582 help 583 This option allows you to use an ADB keyboard attached to your 584 machine. Note that this disables any other (ie. PS/2) keyboard 585 support, even if your machine is physically capable of using both at 586 the same time. 587 588 If you use an ADB keyboard (4 pin connector), say Y here. 589 If you use a PS/2 keyboard (6 pin connector), say N here. 590 591config HPDCA 592 tristate "HP DCA serial support" 593 depends on DIO && SERIAL_8250 594 help 595 If you want to use the internal "DCA" serial ports on an HP300 596 machine, say Y here. 597 598config HPAPCI 599 tristate "HP APCI serial support" 600 depends on HP300 && SERIAL_8250 && EXPERIMENTAL 601 help 602 If you want to use the internal "APCI" serial ports on an HP400 603 machine, say Y here. 604 605config MVME147_SCC 606 bool "SCC support for MVME147 serial ports" 607 depends on MVME147 608 help 609 This is the driver for the serial ports on the Motorola MVME147 610 boards. Everyone using one of these boards should say Y here. 611 612config SERIAL167 613 bool "CD2401 support for MVME166/7 serial ports" 614 depends on MVME16x && BROKEN 615 help 616 This is the driver for the serial ports on the Motorola MVME166, 617 167, and 172 boards. Everyone using one of these boards should say 618 Y here. 619 620config MVME162_SCC 621 bool "SCC support for MVME162 serial ports" 622 depends on MVME16x 623 help 624 This is the driver for the serial ports on the Motorola MVME162 and 625 172 boards. Everyone using one of these boards should say Y here. 626 627config BVME6000_SCC 628 bool "SCC support for BVME6000 serial ports" 629 depends on BVME6000 630 help 631 This is the driver for the serial ports on the BVME4000 and BVME6000 632 boards from BVM Ltd. Everyone using one of these boards should say 633 Y here. 634 635config DN_SERIAL 636 bool "Support for DN serial port (dummy)" 637 depends on APOLLO 638 639config SERIAL_CONSOLE 640 bool "Support for serial port console" 641 depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) 642 ---help--- 643 If you say Y here, it will be possible to use a serial port as the 644 system console (the system console is the device which receives all 645 kernel messages and warnings and which allows logins in single user 646 mode). This could be useful if some terminal or printer is connected 647 to that serial port. 648 649 Even if you say Y here, the currently visible virtual console 650 (/dev/tty0) will still be used as the system console by default, but 651 you can alter that using a kernel command line option such as 652 "console=ttyS1". (Try "man bootparam" or see the documentation of 653 your boot loader (lilo or loadlin) about how to pass options to the 654 kernel at boot time.) 655 656 If you don't have a VGA card installed and you say Y here, the 657 kernel will automatically use the first serial line, /dev/ttyS0, as 658 system console. 659 660 If unsure, say N. 661 662endmenu 663 664source "fs/Kconfig" 665 666source "arch/m68k/Kconfig.debug" 667 668source "security/Kconfig" 669 670source "crypto/Kconfig" 671 672source "lib/Kconfig" 673