xref: /linux/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml (revision a1c613ae4c322ddd58d5a8539dbfba2a0380a8c0)

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8183-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: MediaTek MT8183 Pin Controller

maintainers:
  - Sean Wang <sean.wang@kernel.org>

description:
  The MediaTek's MT8183 Pin controller is used to control SoC pins.

properties:
  compatible:
    const: mediatek,mt8183-pinctrl

  reg:
    minItems: 10
    maxItems: 10

  reg-names:
    items:
      - const: iocfg0
      - const: iocfg1
      - const: iocfg2
      - const: iocfg3
      - const: iocfg4
      - const: iocfg5
      - const: iocfg6
      - const: iocfg7
      - const: iocfg8
      - const: eint

  gpio-controller: true

  "#gpio-cells":
    const: 2
    description:
      Number of cells in GPIO specifier. Since the generic GPIO binding is used,
      the amount of cells must be specified as 2. See the below mentioned gpio
      binding representation for description of particular cells.

  gpio-ranges:
    minItems: 1
    maxItems: 5
    description:
      GPIO valid number range.

  interrupt-controller: true

  interrupts:
    maxItems: 1

  "#interrupt-cells":
    const: 2

allOf:
  - $ref: pinctrl.yaml#

required:
  - compatible
  - reg
  - gpio-controller
  - "#gpio-cells"
  - gpio-ranges

patternProperties:
  '-pins(-[a-z]+)?$':
    type: object
    additionalProperties: false
    patternProperties:
      '^pins':
        type: object
        additionalProperties: false
        description:
          A pinctrl node should contain at least one subnodes representing the
          pinctrl groups available on the machine. Each subnode will list the
          pins it needs, and how they should be configured, with regard to muxer
          configuration, pullups, drive strength, input enable/disable and input
          schmitt.
        $ref: /schemas/pinctrl/pincfg-node.yaml

        properties:
          pinmux:
            description:
              Integer array, represents gpio pin number and mux setting.
              Supported pin number and mux varies for different SoCs, and are
              defined as macros in <soc>-pinfunc.h directly.

          bias-disable: true

          bias-pull-up: true

          bias-pull-down: true

          input-enable: true

          input-disable: true

          output-low: true

          output-high: true

          input-schmitt-enable: true

          input-schmitt-disable: true

          drive-strength:
            enum: [2, 4, 6, 8, 10, 12, 14, 16]

          drive-strength-microamp:
            enum: [125, 250, 500, 1000]

          mediatek,drive-strength-adv:
            deprecated: true
            description: |
              DEPRECATED: Please use drive-strength-microamp instead.
              Describe the specific driving setup property.
              For I2C pins, the existing generic driving setup can only support
              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
              driving setup, the existing generic setup will be disabled.
              The specific driving setup is controlled by E1E0EN.
              When E1=0/E0=0, the strength is 0.125mA.
              When E1=0/E0=1, the strength is 0.25mA.
              When E1=1/E0=0, the strength is 0.5mA.
              When E1=1/E0=1, the strength is 1mA.
              EN is used to enable or disable the specific driving setup.
              Valid arguments are described as below:
              0: (E1, E0, EN) = (0, 0, 0)
              1: (E1, E0, EN) = (0, 0, 1)
              2: (E1, E0, EN) = (0, 1, 0)
              3: (E1, E0, EN) = (0, 1, 1)
              4: (E1, E0, EN) = (1, 0, 0)
              5: (E1, E0, EN) = (1, 0, 1)
              6: (E1, E0, EN) = (1, 1, 0)
              7: (E1, E0, EN) = (1, 1, 1)
              So the valid arguments are from 0 to 7.
            $ref: /schemas/types.yaml#/definitions/uint32
            enum: [0, 1, 2, 3, 4, 5, 6, 7]

          mediatek,pull-up-adv:
            description: |
              Pull up settings for 2 pull resistors, R0 and R1. User can
              configure those special pins. Valid arguments are described as
              below:
              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
            $ref: /schemas/types.yaml#/definitions/uint32
            enum: [0, 1, 2, 3]

          mediatek,pull-down-adv:
            description: |
              Pull down settings for 2 pull resistors, R0 and R1. User can
              configure those special pins. Valid arguments are described as
              below:
              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
            $ref: /schemas/types.yaml#/definitions/uint32
            enum: [0, 1, 2, 3]

          mediatek,tdsel:
            description:
              An integer describing the steps for output level shifter duty
              cycle when asserted (high pulse width adjustment). Valid arguments
              are from 0 to 15.
            $ref: /schemas/types.yaml#/definitions/uint32

          mediatek,rdsel:
            description:
              An integer describing the steps for input level shifter duty cycle
              when asserted (high pulse width adjustment). Valid arguments are
              from 0 to 63.
            $ref: /schemas/types.yaml#/definitions/uint32

        required:
          - pinmux

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/pinctrl/mt8183-pinfunc.h>

    soc {
        #address-cells = <2>;
        #size-cells = <2>;

        pio: pinctrl@10005000 {
          compatible = "mediatek,mt8183-pinctrl";
          reg = <0 0x10005000 0 0x1000>,
                <0 0x11f20000 0 0x1000>,
                <0 0x11e80000 0 0x1000>,
                <0 0x11e70000 0 0x1000>,
                <0 0x11e90000 0 0x1000>,
                <0 0x11d30000 0 0x1000>,
                <0 0x11d20000 0 0x1000>,
                <0 0x11c50000 0 0x1000>,
                <0 0x11f30000 0 0x1000>,
                <0 0x1000b000 0 0x1000>;
          reg-names = "iocfg0", "iocfg1", "iocfg2",
                "iocfg3", "iocfg4", "iocfg5",
                "iocfg6", "iocfg7", "iocfg8",
                "eint";
          gpio-controller;
          #gpio-cells = <2>;
          gpio-ranges = <&pio 0 0 192>;
          interrupt-controller;
          interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
          #interrupt-cells = <2>;

          i2c0_pins_a: i2c0-pins {
            pins1 {
              pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
                <PINMUX_GPIO49__FUNC_SDA5>;
              mediatek,pull-up-adv = <3>;
              drive-strength-microamp = <1000>;
            };
          };

          i2c1_pins_a: i2c1-pins {
            pins {
              pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
                <PINMUX_GPIO51__FUNC_SDA3>;
              mediatek,pull-down-adv = <2>;
            };
          };
        };
    };