1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/i3c/i3c.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: I3C bus 8 9maintainers: 10 - Alexandre Belloni <alexandre.belloni@bootlin.com> 11 - Miquel Raynal <miquel.raynal@bootlin.com> 12 13description: | 14 I3C busses can be described with a node for the primary I3C controller device 15 and a set of child nodes for each I2C or I3C slave on the bus. Each of them 16 may, during the life of the bus, request mastership. 17 18properties: 19 $nodename: 20 pattern: "^i3c@[0-9a-f]+$" 21 22 "#address-cells": 23 const: 3 24 description: | 25 Each I2C device connected to the bus should be described in a subnode. 26 27 All I3C devices are supposed to support DAA (Dynamic Address Assignment), 28 and are thus discoverable. So, by default, I3C devices do not have to be 29 described in the device tree. This being said, one might want to attach 30 extra resources to these devices, and those resources may have to be 31 described in the device tree, which in turn means we have to describe 32 I3C devices. 33 34 Another use case for describing an I3C device in the device tree is when 35 this I3C device has a static I2C address and we want to assign it a 36 specific I3C dynamic address before the DAA takes place (so that other 37 devices on the bus can't take this dynamic address). 38 39 "#size-cells": 40 const: 0 41 42 i3c-scl-hz: 43 description: | 44 Frequency of the SCL signal used for I3C transfers. When undefined, the 45 default value should be 12.5MHz. 46 47 May not be supported by all controllers. 48 49 i2c-scl-hz: 50 description: | 51 Frequency of the SCL signal used for I2C transfers. When undefined, the 52 default should be to look at LVR (Legacy Virtual Register) values of 53 I2C devices described in the device tree to determine the maximum I2C 54 frequency. 55 56 May not be supported by all controllers. 57 58 mctp-controller: 59 type: boolean 60 description: | 61 Indicates that the system is accessible via this bus as an endpoint for 62 MCTP over I3C transport. 63 64required: 65 - "#address-cells" 66 - "#size-cells" 67 68patternProperties: 69 "@[0-9a-f]+$": 70 type: object 71 description: | 72 I2C child, should be named: <device-type>@<i2c-address> 73 74 All properties described in dtschema schemas/i2c/i2c-controller.yaml 75 are valid here, except the reg property whose content is changed. 76 77 properties: 78 compatible: 79 description: 80 Compatible of the I2C device. 81 82 reg: 83 items: 84 - items: 85 - description: | 86 I2C address. 10 bit addressing is not supported. Devices with 87 10-bit address can't be properly passed through DEFSLVS 88 command. 89 minimum: 0 90 maximum: 0x7f 91 - const: 0 92 - description: | 93 Shall encode the I3C LVR (Legacy Virtual Register): 94 See include/dt-bindings/i3c/i3c.h 95 bit[31:8]: unused/ignored 96 bit[7:5]: I2C device index. Possible values: 97 * 0: I2C device has a 50 ns spike filter 98 * 1: I2C device does not have a 50 ns spike filter but 99 supports high frequency on SCL 100 * 2: I2C device does not have a 50 ns spike filter and is 101 not tolerant to high frequencies 102 * 3-7: reserved 103 bit[4]: tell whether the device operates in FM (Fast Mode) 104 or FM+ mode: 105 * 0: FM+ mode 106 * 1: FM mode 107 bit[3:0]: device type 108 * 0-15: reserved 109 110 required: 111 - compatible 112 - reg 113 114 "@[0-9a-f]+,[0-9a-f]+$": 115 type: object 116 description: | 117 I3C child, should be named: <device-type>@<static-i2c-address>,<i3c-pid> 118 119 properties: 120 reg: 121 items: 122 - items: 123 - description: | 124 Encodes the static I2C address. Should be 0 if the device does 125 not have one (0 is not a valid I2C address). 126 minimum: 0 127 maximum: 0x7f 128 - description: | 129 First half of the Provisioned ID (following the PID 130 definition provided by the I3C specification). 131 132 Contains the manufacturer ID left-shifted by 1. 133 - description: | 134 Second half of the Provisioned ID (following the PID 135 definition provided by the I3C specification). 136 137 Contains the ORing of the part ID left-shifted by 16, 138 the instance ID left-shifted by 12 and extra information. 139 140 assigned-address: 141 $ref: /schemas/types.yaml#/definitions/uint32 142 minimum: 0x1 143 maximum: 0xff 144 description: | 145 Dynamic address to be assigned to this device. In case static address is 146 present (first cell of the reg property != 0), this address is assigned 147 through SETDASA. If static address is not present, this address is assigned 148 through SETNEWDA after assigning a temporary address via ENTDAA. 149 150 required: 151 - reg 152 153additionalProperties: true 154 155examples: 156 - | 157 #include <dt-bindings/i3c/i3c.h> 158 159 i3c@d040000 { 160 compatible = "cdns,i3c-master"; 161 clocks = <&coreclock>, <&i3csysclock>; 162 clock-names = "pclk", "sysclk"; 163 interrupts = <3 0>; 164 reg = <0x0d040000 0x1000>; 165 #address-cells = <3>; 166 #size-cells = <0>; 167 i2c-scl-hz = <100000>; 168 169 /* I2C device. */ 170 eeprom@57 { 171 compatible = "atmel,24c01"; 172 reg = <0x57 0x0 (I2C_FM | I2C_FILTER)>; 173 pagesize = <0x8>; 174 }; 175 176 /* I3C device with a static I2C address and assigned address. */ 177 thermal_sensor: sensor@68,39200144004 { 178 reg = <0x68 0x392 0x144004>; 179 assigned-address = <0xa>; 180 }; 181 182 /* I3C device with only assigned address. */ 183 pressure_sensor: sensor@0,39200124004 { 184 reg = <0x0 0x392 0x124000>; 185 assigned-address = <0xc>; 186 }; 187 188 /* 189 * I3C device without a static I2C address but requiring 190 * resources described in the DT. 191 */ 192 sensor@0,39200154004 { 193 reg = <0x0 0x392 0x154004>; 194 clocks = <&clock_provider 0>; 195 }; 196 }; 197