1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (C) 2012 Ben Gray <bgray@freebsd.org>. 5 * Copyright (C) 2018 The FreeBSD Foundation. 6 * 7 * This software was developed by Arshan Khanifar <arshankhanifar@gmail.com> 8 * under sponsorship from the FreeBSD Foundation. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 23 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 29 * SUCH DAMAGE. 30 * 31 * $FreeBSD$ 32 */ 33 34 #include <sys/cdefs.h> 35 __FBSDID("$FreeBSD$"); 36 37 /* 38 * USB-To-Ethernet adapter driver for Microchip's LAN78XX and related families. 39 * 40 * USB 3.1 to 10/100/1000 Mbps Ethernet 41 * LAN7800 http://www.microchip.com/wwwproducts/en/LAN7800 42 * 43 * USB 2.0 to 10/100/1000 Mbps Ethernet 44 * LAN7850 http://www.microchip.com/wwwproducts/en/LAN7850 45 * 46 * USB 2 to 10/100/1000 Mbps Ethernet with built-in USB hub 47 * LAN7515 (no datasheet available, but probes and functions as LAN7800) 48 * 49 * This driver is based on the if_smsc driver, with lan78xx-specific 50 * functionality modelled on Microchip's Linux lan78xx driver. 51 * 52 * UNIMPLEMENTED FEATURES 53 * ------------------ 54 * A number of features supported by the lan78xx are not yet implemented in 55 * this driver: 56 * 57 * - TX checksum offloading: Nothing has been implemented yet. 58 * - Direct address translation filtering: Implemented but untested. 59 * - VLAN tag removal. 60 * - Support for USB interrupt endpoints. 61 * - Latency Tolerance Messaging (LTM) support. 62 * - TCP LSO support. 63 * 64 */ 65 66 #include <sys/param.h> 67 #include <sys/bus.h> 68 #include <sys/callout.h> 69 #include <sys/condvar.h> 70 #include <sys/kernel.h> 71 #include <sys/lock.h> 72 #include <sys/malloc.h> 73 #include <sys/module.h> 74 #include <sys/mutex.h> 75 #include <sys/priv.h> 76 #include <sys/queue.h> 77 #include <sys/random.h> 78 #include <sys/socket.h> 79 #include <sys/stddef.h> 80 #include <sys/stdint.h> 81 #include <sys/sx.h> 82 #include <sys/sysctl.h> 83 #include <sys/systm.h> 84 #include <sys/unistd.h> 85 86 #include <net/if.h> 87 #include <net/if_var.h> 88 #include <net/if_media.h> 89 90 #include <dev/mii/mii.h> 91 #include <dev/mii/miivar.h> 92 93 #include <netinet/in.h> 94 #include <netinet/ip.h> 95 96 #include "opt_platform.h" 97 98 #ifdef FDT 99 #include <dev/fdt/fdt_common.h> 100 #include <dev/ofw/ofw_bus.h> 101 #include <dev/ofw/ofw_bus_subr.h> 102 #include <dev/usb/usb_fdt_support.h> 103 #endif 104 105 #include <dev/usb/usb.h> 106 #include <dev/usb/usbdi.h> 107 #include <dev/usb/usbdi_util.h> 108 #include "usbdevs.h" 109 110 #define USB_DEBUG_VAR lan78xx_debug 111 #include <dev/usb/usb_debug.h> 112 #include <dev/usb/usb_process.h> 113 114 #include <dev/usb/net/usb_ethernet.h> 115 116 #include <dev/usb/net/if_mugereg.h> 117 118 #include "miibus_if.h" 119 120 #ifdef USB_DEBUG 121 static int muge_debug = 0; 122 123 SYSCTL_NODE(_hw_usb, OID_AUTO, muge, CTLFLAG_RW | CTLFLAG_MPSAFE, 0, 124 "Microchip LAN78xx USB-GigE"); 125 SYSCTL_INT(_hw_usb_muge, OID_AUTO, debug, CTLFLAG_RWTUN, &muge_debug, 0, 126 "Debug level"); 127 #endif 128 129 #define MUGE_DEFAULT_TX_CSUM_ENABLE (false) 130 #define MUGE_DEFAULT_TSO_ENABLE (false) 131 132 /* Supported Vendor and Product IDs. */ 133 static const struct usb_device_id lan78xx_devs[] = { 134 #define MUGE_DEV(p,i) { USB_VPI(USB_VENDOR_SMC2, USB_PRODUCT_SMC2_##p, i) } 135 MUGE_DEV(LAN7800_ETH, 0), 136 MUGE_DEV(LAN7801_ETH, 0), 137 MUGE_DEV(LAN7850_ETH, 0), 138 #undef MUGE_DEV 139 }; 140 141 #ifdef USB_DEBUG 142 #define muge_dbg_printf(sc, fmt, args...) \ 143 do { \ 144 if (muge_debug > 0) \ 145 device_printf((sc)->sc_ue.ue_dev, "debug: " fmt, ##args); \ 146 } while(0) 147 #else 148 #define muge_dbg_printf(sc, fmt, args...) do { } while (0) 149 #endif 150 151 #define muge_warn_printf(sc, fmt, args...) \ 152 device_printf((sc)->sc_ue.ue_dev, "warning: " fmt, ##args) 153 154 #define muge_err_printf(sc, fmt, args...) \ 155 device_printf((sc)->sc_ue.ue_dev, "error: " fmt, ##args) 156 157 #define ETHER_IS_VALID(addr) \ 158 (!ETHER_IS_MULTICAST(addr) && !ETHER_IS_ZERO(addr)) 159 160 /* USB endpoints. */ 161 162 enum { 163 MUGE_BULK_DT_RD, 164 MUGE_BULK_DT_WR, 165 #if 0 /* Ignore interrupt endpoints for now as we poll on MII status. */ 166 MUGE_INTR_DT_WR, 167 MUGE_INTR_DT_RD, 168 #endif 169 MUGE_N_TRANSFER, 170 }; 171 172 struct muge_softc { 173 struct usb_ether sc_ue; 174 struct mtx sc_mtx; 175 struct usb_xfer *sc_xfer[MUGE_N_TRANSFER]; 176 int sc_phyno; 177 uint32_t sc_leds; 178 uint16_t sc_led_modes; 179 uint16_t sc_led_modes_mask; 180 181 /* Settings for the mac control (MAC_CSR) register. */ 182 uint32_t sc_rfe_ctl; 183 uint32_t sc_mdix_ctl; 184 uint16_t chipid; 185 uint16_t chiprev; 186 uint32_t sc_mchash_table[ETH_DP_SEL_VHF_HASH_LEN]; 187 uint32_t sc_pfilter_table[MUGE_NUM_PFILTER_ADDRS_][2]; 188 189 uint32_t sc_flags; 190 #define MUGE_FLAG_LINK 0x0001 191 #define MUGE_FLAG_INIT_DONE 0x0002 192 }; 193 194 #define MUGE_IFACE_IDX 0 195 196 #define MUGE_LOCK(_sc) mtx_lock(&(_sc)->sc_mtx) 197 #define MUGE_UNLOCK(_sc) mtx_unlock(&(_sc)->sc_mtx) 198 #define MUGE_LOCK_ASSERT(_sc, t) mtx_assert(&(_sc)->sc_mtx, t) 199 200 static device_probe_t muge_probe; 201 static device_attach_t muge_attach; 202 static device_detach_t muge_detach; 203 204 static usb_callback_t muge_bulk_read_callback; 205 static usb_callback_t muge_bulk_write_callback; 206 207 static miibus_readreg_t lan78xx_miibus_readreg; 208 static miibus_writereg_t lan78xx_miibus_writereg; 209 static miibus_statchg_t lan78xx_miibus_statchg; 210 211 static int muge_attach_post_sub(struct usb_ether *ue); 212 static uether_fn_t muge_attach_post; 213 static uether_fn_t muge_init; 214 static uether_fn_t muge_stop; 215 static uether_fn_t muge_start; 216 static uether_fn_t muge_tick; 217 static uether_fn_t muge_setmulti; 218 static uether_fn_t muge_setpromisc; 219 220 static int muge_ifmedia_upd(struct ifnet *); 221 static void muge_ifmedia_sts(struct ifnet *, struct ifmediareq *); 222 223 static int lan78xx_chip_init(struct muge_softc *sc); 224 static int muge_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data); 225 226 static const struct usb_config muge_config[MUGE_N_TRANSFER] = { 227 [MUGE_BULK_DT_WR] = { 228 .type = UE_BULK, 229 .endpoint = UE_ADDR_ANY, 230 .direction = UE_DIR_OUT, 231 .frames = 16, 232 .bufsize = 16 * (MCLBYTES + 16), 233 .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, 234 .callback = muge_bulk_write_callback, 235 .timeout = 10000, /* 10 seconds */ 236 }, 237 238 [MUGE_BULK_DT_RD] = { 239 .type = UE_BULK, 240 .endpoint = UE_ADDR_ANY, 241 .direction = UE_DIR_IN, 242 .bufsize = 20480, /* bytes */ 243 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 244 .callback = muge_bulk_read_callback, 245 .timeout = 0, /* no timeout */ 246 }, 247 /* 248 * The chip supports interrupt endpoints, however they aren't 249 * needed as we poll on the MII status. 250 */ 251 }; 252 253 static const struct usb_ether_methods muge_ue_methods = { 254 .ue_attach_post = muge_attach_post, 255 .ue_attach_post_sub = muge_attach_post_sub, 256 .ue_start = muge_start, 257 .ue_ioctl = muge_ioctl, 258 .ue_init = muge_init, 259 .ue_stop = muge_stop, 260 .ue_tick = muge_tick, 261 .ue_setmulti = muge_setmulti, 262 .ue_setpromisc = muge_setpromisc, 263 .ue_mii_upd = muge_ifmedia_upd, 264 .ue_mii_sts = muge_ifmedia_sts, 265 }; 266 267 /** 268 * lan78xx_read_reg - Read a 32-bit register on the device 269 * @sc: driver soft context 270 * @off: offset of the register 271 * @data: pointer a value that will be populated with the register value 272 * 273 * LOCKING: 274 * The device lock must be held before calling this function. 275 * 276 * RETURNS: 277 * 0 on success, a USB_ERR_?? error code on failure. 278 */ 279 static int 280 lan78xx_read_reg(struct muge_softc *sc, uint32_t off, uint32_t *data) 281 { 282 struct usb_device_request req; 283 uint32_t buf; 284 usb_error_t err; 285 286 MUGE_LOCK_ASSERT(sc, MA_OWNED); 287 288 req.bmRequestType = UT_READ_VENDOR_DEVICE; 289 req.bRequest = UVR_READ_REG; 290 USETW(req.wValue, 0); 291 USETW(req.wIndex, off); 292 USETW(req.wLength, 4); 293 294 err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); 295 if (err != 0) 296 muge_warn_printf(sc, "Failed to read register 0x%0x\n", off); 297 *data = le32toh(buf); 298 return (err); 299 } 300 301 /** 302 * lan78xx_write_reg - Write a 32-bit register on the device 303 * @sc: driver soft context 304 * @off: offset of the register 305 * @data: the 32-bit value to write into the register 306 * 307 * LOCKING: 308 * The device lock must be held before calling this function. 309 * 310 * RETURNS: 311 * 0 on success, a USB_ERR_?? error code on failure. 312 */ 313 static int 314 lan78xx_write_reg(struct muge_softc *sc, uint32_t off, uint32_t data) 315 { 316 struct usb_device_request req; 317 uint32_t buf; 318 usb_error_t err; 319 320 MUGE_LOCK_ASSERT(sc, MA_OWNED); 321 322 buf = htole32(data); 323 324 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 325 req.bRequest = UVR_WRITE_REG; 326 USETW(req.wValue, 0); 327 USETW(req.wIndex, off); 328 USETW(req.wLength, 4); 329 330 err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); 331 if (err != 0) 332 muge_warn_printf(sc, "Failed to write register 0x%0x\n", off); 333 return (err); 334 } 335 336 /** 337 * lan78xx_wait_for_bits - Poll on a register value until bits are cleared 338 * @sc: soft context 339 * @reg: offset of the register 340 * @bits: if the bits are clear the function returns 341 * 342 * LOCKING: 343 * The device lock must be held before calling this function. 344 * 345 * RETURNS: 346 * 0 on success, or a USB_ERR_?? error code on failure. 347 */ 348 static int 349 lan78xx_wait_for_bits(struct muge_softc *sc, uint32_t reg, uint32_t bits) 350 { 351 usb_ticks_t start_ticks; 352 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 353 uint32_t val; 354 int err; 355 356 MUGE_LOCK_ASSERT(sc, MA_OWNED); 357 358 start_ticks = (usb_ticks_t)ticks; 359 do { 360 if ((err = lan78xx_read_reg(sc, reg, &val)) != 0) 361 return (err); 362 if (!(val & bits)) 363 return (0); 364 uether_pause(&sc->sc_ue, hz / 100); 365 } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); 366 367 return (USB_ERR_TIMEOUT); 368 } 369 370 /** 371 * lan78xx_eeprom_read_raw - Read the attached EEPROM 372 * @sc: soft context 373 * @off: the eeprom address offset 374 * @buf: stores the bytes 375 * @buflen: the number of bytes to read 376 * 377 * Simply reads bytes from an attached eeprom. 378 * 379 * LOCKING: 380 * The function takes and releases the device lock if not already held. 381 * 382 * RETURNS: 383 * 0 on success, or a USB_ERR_?? error code on failure. 384 */ 385 static int 386 lan78xx_eeprom_read_raw(struct muge_softc *sc, uint16_t off, uint8_t *buf, 387 uint16_t buflen) 388 { 389 usb_ticks_t start_ticks; 390 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 391 int err; 392 uint32_t val, saved; 393 uint16_t i; 394 bool locked; 395 396 locked = mtx_owned(&sc->sc_mtx); /* XXX */ 397 if (!locked) 398 MUGE_LOCK(sc); 399 400 if (sc->chipid == ETH_ID_REV_CHIP_ID_7800_) { 401 /* EEDO/EECLK muxed with LED0/LED1 on LAN7800. */ 402 err = lan78xx_read_reg(sc, ETH_HW_CFG, &val); 403 saved = val; 404 405 val &= ~(ETH_HW_CFG_LEDO_EN_ | ETH_HW_CFG_LED1_EN_); 406 err = lan78xx_write_reg(sc, ETH_HW_CFG, val); 407 } 408 409 err = lan78xx_wait_for_bits(sc, ETH_E2P_CMD, ETH_E2P_CMD_BUSY_); 410 if (err != 0) { 411 muge_warn_printf(sc, "eeprom busy, failed to read data\n"); 412 goto done; 413 } 414 415 /* Start reading the bytes, one at a time. */ 416 for (i = 0; i < buflen; i++) { 417 val = ETH_E2P_CMD_BUSY_ | ETH_E2P_CMD_READ_; 418 val |= (ETH_E2P_CMD_ADDR_MASK_ & (off + i)); 419 if ((err = lan78xx_write_reg(sc, ETH_E2P_CMD, val)) != 0) 420 goto done; 421 422 start_ticks = (usb_ticks_t)ticks; 423 do { 424 if ((err = lan78xx_read_reg(sc, ETH_E2P_CMD, &val)) != 425 0) 426 goto done; 427 if (!(val & ETH_E2P_CMD_BUSY_) || 428 (val & ETH_E2P_CMD_TIMEOUT_)) 429 break; 430 431 uether_pause(&sc->sc_ue, hz / 100); 432 } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); 433 434 if (val & (ETH_E2P_CMD_BUSY_ | ETH_E2P_CMD_TIMEOUT_)) { 435 muge_warn_printf(sc, "eeprom command failed\n"); 436 err = USB_ERR_IOERROR; 437 break; 438 } 439 440 if ((err = lan78xx_read_reg(sc, ETH_E2P_DATA, &val)) != 0) 441 goto done; 442 443 buf[i] = (val & 0xff); 444 } 445 446 done: 447 if (!locked) 448 MUGE_UNLOCK(sc); 449 if (sc->chipid == ETH_ID_REV_CHIP_ID_7800_) { 450 /* Restore saved LED configuration. */ 451 lan78xx_write_reg(sc, ETH_HW_CFG, saved); 452 } 453 return (err); 454 } 455 456 static bool 457 lan78xx_eeprom_present(struct muge_softc *sc) 458 { 459 int ret; 460 uint8_t sig; 461 462 ret = lan78xx_eeprom_read_raw(sc, ETH_E2P_INDICATOR_OFFSET, &sig, 1); 463 return (ret == 0 && sig == ETH_E2P_INDICATOR); 464 } 465 466 /** 467 * lan78xx_otp_read_raw 468 * @sc: soft context 469 * @off: the otp address offset 470 * @buf: stores the bytes 471 * @buflen: the number of bytes to read 472 * 473 * Simply reads bytes from the OTP. 474 * 475 * LOCKING: 476 * The function takes and releases the device lock if not already held. 477 * 478 * RETURNS: 479 * 0 on success, or a USB_ERR_?? error code on failure. 480 * 481 */ 482 static int 483 lan78xx_otp_read_raw(struct muge_softc *sc, uint16_t off, uint8_t *buf, 484 uint16_t buflen) 485 { 486 int err; 487 uint32_t val; 488 uint16_t i; 489 bool locked; 490 locked = mtx_owned(&sc->sc_mtx); 491 if (!locked) 492 MUGE_LOCK(sc); 493 494 err = lan78xx_read_reg(sc, OTP_PWR_DN, &val); 495 496 /* Checking if bit is set. */ 497 if (val & OTP_PWR_DN_PWRDN_N) { 498 /* Clear it, then wait for it to be cleared. */ 499 lan78xx_write_reg(sc, OTP_PWR_DN, 0); 500 err = lan78xx_wait_for_bits(sc, OTP_PWR_DN, OTP_PWR_DN_PWRDN_N); 501 if (err != 0) { 502 muge_warn_printf(sc, "OTP off? failed to read data\n"); 503 goto done; 504 } 505 } 506 /* Start reading the bytes, one at a time. */ 507 for (i = 0; i < buflen; i++) { 508 err = lan78xx_write_reg(sc, OTP_ADDR1, 509 ((off + i) >> 8) & OTP_ADDR1_15_11); 510 err = lan78xx_write_reg(sc, OTP_ADDR2, 511 ((off + i) & OTP_ADDR2_10_3)); 512 err = lan78xx_write_reg(sc, OTP_FUNC_CMD, OTP_FUNC_CMD_READ_); 513 err = lan78xx_write_reg(sc, OTP_CMD_GO, OTP_CMD_GO_GO_); 514 515 err = lan78xx_wait_for_bits(sc, OTP_STATUS, OTP_STATUS_BUSY_); 516 if (err != 0) { 517 muge_warn_printf(sc, "OTP busy failed to read data\n"); 518 goto done; 519 } 520 521 if ((err = lan78xx_read_reg(sc, OTP_RD_DATA, &val)) != 0) 522 goto done; 523 524 buf[i] = (uint8_t)(val & 0xff); 525 } 526 527 done: 528 if (!locked) 529 MUGE_UNLOCK(sc); 530 return (err); 531 } 532 533 /** 534 * lan78xx_otp_read 535 * @sc: soft context 536 * @off: the otp address offset 537 * @buf: stores the bytes 538 * @buflen: the number of bytes to read 539 * 540 * Simply reads bytes from the otp. 541 * 542 * LOCKING: 543 * The function takes and releases device lock if it is not already held. 544 * 545 * RETURNS: 546 * 0 on success, or a USB_ERR_?? error code on failure. 547 */ 548 static int 549 lan78xx_otp_read(struct muge_softc *sc, uint16_t off, uint8_t *buf, 550 uint16_t buflen) 551 { 552 uint8_t sig; 553 int err; 554 555 err = lan78xx_otp_read_raw(sc, OTP_INDICATOR_OFFSET, &sig, 1); 556 if (err == 0) { 557 if (sig == OTP_INDICATOR_1) { 558 } else if (sig == OTP_INDICATOR_2) { 559 off += 0x100; /* XXX */ 560 } else { 561 err = -EINVAL; 562 } 563 if (!err) 564 err = lan78xx_otp_read_raw(sc, off, buf, buflen); 565 } 566 return (err); 567 } 568 569 /** 570 * lan78xx_setmacaddress - Set the mac address in the device 571 * @sc: driver soft context 572 * @addr: pointer to array contain at least 6 bytes of the mac 573 * 574 * LOCKING: 575 * Should be called with the MUGE lock held. 576 * 577 * RETURNS: 578 * Returns 0 on success or a negative error code. 579 */ 580 static int 581 lan78xx_setmacaddress(struct muge_softc *sc, const uint8_t *addr) 582 { 583 int err; 584 uint32_t val; 585 586 muge_dbg_printf(sc, 587 "setting mac address to %02x:%02x:%02x:%02x:%02x:%02x\n", 588 addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); 589 590 MUGE_LOCK_ASSERT(sc, MA_OWNED); 591 592 val = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0]; 593 if ((err = lan78xx_write_reg(sc, ETH_RX_ADDRL, val)) != 0) 594 goto done; 595 596 val = (addr[5] << 8) | addr[4]; 597 err = lan78xx_write_reg(sc, ETH_RX_ADDRH, val); 598 599 done: 600 return (err); 601 } 602 603 /** 604 * lan78xx_set_rx_max_frame_length 605 * @sc: driver soft context 606 * @size: pointer to array contain at least 6 bytes of the mac 607 * 608 * Sets the maximum frame length to be received. Frames bigger than 609 * this size are aborted. 610 * 611 * RETURNS: 612 * Returns 0 on success or a negative error code. 613 */ 614 static int 615 lan78xx_set_rx_max_frame_length(struct muge_softc *sc, int size) 616 { 617 int err = 0; 618 uint32_t buf; 619 bool rxenabled; 620 621 /* First we have to disable rx before changing the length. */ 622 err = lan78xx_read_reg(sc, ETH_MAC_RX, &buf); 623 rxenabled = ((buf & ETH_MAC_RX_EN_) != 0); 624 625 if (rxenabled) { 626 buf &= ~ETH_MAC_RX_EN_; 627 err = lan78xx_write_reg(sc, ETH_MAC_RX, buf); 628 } 629 630 /* Setting max frame length. */ 631 buf &= ~ETH_MAC_RX_MAX_FR_SIZE_MASK_; 632 buf |= (((size + 4) << ETH_MAC_RX_MAX_FR_SIZE_SHIFT_) & 633 ETH_MAC_RX_MAX_FR_SIZE_MASK_); 634 err = lan78xx_write_reg(sc, ETH_MAC_RX, buf); 635 636 /* If it were enabled before, we enable it back. */ 637 638 if (rxenabled) { 639 buf |= ETH_MAC_RX_EN_; 640 err = lan78xx_write_reg(sc, ETH_MAC_RX, buf); 641 } 642 643 return (0); 644 } 645 646 /** 647 * lan78xx_miibus_readreg - Read a MII/MDIO register 648 * @dev: usb ether device 649 * @phy: the number of phy reading from 650 * @reg: the register address 651 * 652 * LOCKING: 653 * Takes and releases the device mutex lock if not already held. 654 * 655 * RETURNS: 656 * Returns the 16-bits read from the MII register, if this function fails 657 * 0 is returned. 658 */ 659 static int 660 lan78xx_miibus_readreg(device_t dev, int phy, int reg) 661 { 662 struct muge_softc *sc = device_get_softc(dev); 663 uint32_t addr, val; 664 bool locked; 665 666 val = 0; 667 locked = mtx_owned(&sc->sc_mtx); 668 if (!locked) 669 MUGE_LOCK(sc); 670 671 if (lan78xx_wait_for_bits(sc, ETH_MII_ACC, ETH_MII_ACC_MII_BUSY_) != 672 0) { 673 muge_warn_printf(sc, "MII is busy\n"); 674 goto done; 675 } 676 677 addr = (phy << 11) | (reg << 6) | 678 ETH_MII_ACC_MII_READ_ | ETH_MII_ACC_MII_BUSY_; 679 lan78xx_write_reg(sc, ETH_MII_ACC, addr); 680 681 if (lan78xx_wait_for_bits(sc, ETH_MII_ACC, ETH_MII_ACC_MII_BUSY_) != 682 0) { 683 muge_warn_printf(sc, "MII read timeout\n"); 684 goto done; 685 } 686 687 lan78xx_read_reg(sc, ETH_MII_DATA, &val); 688 val = le32toh(val); 689 690 done: 691 if (!locked) 692 MUGE_UNLOCK(sc); 693 694 return (val & 0xFFFF); 695 } 696 697 /** 698 * lan78xx_miibus_writereg - Writes a MII/MDIO register 699 * @dev: usb ether device 700 * @phy: the number of phy writing to 701 * @reg: the register address 702 * @val: the value to write 703 * 704 * Attempts to write a PHY register through the usb controller registers. 705 * 706 * LOCKING: 707 * Takes and releases the device mutex lock if not already held. 708 * 709 * RETURNS: 710 * Always returns 0 regardless of success or failure. 711 */ 712 static int 713 lan78xx_miibus_writereg(device_t dev, int phy, int reg, int val) 714 { 715 struct muge_softc *sc = device_get_softc(dev); 716 uint32_t addr; 717 bool locked; 718 719 if (sc->sc_phyno != phy) 720 return (0); 721 722 locked = mtx_owned(&sc->sc_mtx); 723 if (!locked) 724 MUGE_LOCK(sc); 725 726 if (lan78xx_wait_for_bits(sc, ETH_MII_ACC, ETH_MII_ACC_MII_BUSY_) != 727 0) { 728 muge_warn_printf(sc, "MII is busy\n"); 729 goto done; 730 } 731 732 val = htole32(val); 733 lan78xx_write_reg(sc, ETH_MII_DATA, val); 734 735 addr = (phy << 11) | (reg << 6) | 736 ETH_MII_ACC_MII_WRITE_ | ETH_MII_ACC_MII_BUSY_; 737 lan78xx_write_reg(sc, ETH_MII_ACC, addr); 738 739 if (lan78xx_wait_for_bits(sc, ETH_MII_ACC, ETH_MII_ACC_MII_BUSY_) != 0) 740 muge_warn_printf(sc, "MII write timeout\n"); 741 742 done: 743 if (!locked) 744 MUGE_UNLOCK(sc); 745 return (0); 746 } 747 748 /* 749 * lan78xx_miibus_statchg - Called to detect phy status change 750 * @dev: usb ether device 751 * 752 * This function is called periodically by the system to poll for status 753 * changes of the link. 754 * 755 * LOCKING: 756 * Takes and releases the device mutex lock if not already held. 757 */ 758 static void 759 lan78xx_miibus_statchg(device_t dev) 760 { 761 struct muge_softc *sc = device_get_softc(dev); 762 struct mii_data *mii = uether_getmii(&sc->sc_ue); 763 struct ifnet *ifp; 764 int err; 765 uint32_t flow = 0; 766 uint32_t fct_flow = 0; 767 bool locked; 768 769 locked = mtx_owned(&sc->sc_mtx); 770 if (!locked) 771 MUGE_LOCK(sc); 772 773 ifp = uether_getifp(&sc->sc_ue); 774 if (mii == NULL || ifp == NULL || 775 (ifp->if_drv_flags & IFF_DRV_RUNNING) == 0) 776 goto done; 777 778 /* Use the MII status to determine link status */ 779 sc->sc_flags &= ~MUGE_FLAG_LINK; 780 if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) == 781 (IFM_ACTIVE | IFM_AVALID)) { 782 muge_dbg_printf(sc, "media is active\n"); 783 switch (IFM_SUBTYPE(mii->mii_media_active)) { 784 case IFM_10_T: 785 case IFM_100_TX: 786 sc->sc_flags |= MUGE_FLAG_LINK; 787 muge_dbg_printf(sc, "10/100 ethernet\n"); 788 break; 789 case IFM_1000_T: 790 sc->sc_flags |= MUGE_FLAG_LINK; 791 muge_dbg_printf(sc, "Gigabit ethernet\n"); 792 break; 793 default: 794 break; 795 } 796 } 797 /* Lost link, do nothing. */ 798 if ((sc->sc_flags & MUGE_FLAG_LINK) == 0) { 799 muge_dbg_printf(sc, "link flag not set\n"); 800 goto done; 801 } 802 803 err = lan78xx_read_reg(sc, ETH_FCT_FLOW, &fct_flow); 804 if (err) { 805 muge_warn_printf(sc, 806 "failed to read initial flow control thresholds, error %d\n", 807 err); 808 goto done; 809 } 810 811 /* Enable/disable full duplex operation and TX/RX pause. */ 812 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_FDX) != 0) { 813 muge_dbg_printf(sc, "full duplex operation\n"); 814 815 /* Enable transmit MAC flow control function. */ 816 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_TXPAUSE) != 0) 817 flow |= ETH_FLOW_CR_TX_FCEN_ | 0xFFFF; 818 819 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_RXPAUSE) != 0) 820 flow |= ETH_FLOW_CR_RX_FCEN_; 821 } 822 823 /* XXX Flow control settings obtained from Microchip's driver. */ 824 switch(usbd_get_speed(sc->sc_ue.ue_udev)) { 825 case USB_SPEED_SUPER: 826 fct_flow = 0x817; 827 break; 828 case USB_SPEED_HIGH: 829 fct_flow = 0x211; 830 break; 831 default: 832 break; 833 } 834 835 err += lan78xx_write_reg(sc, ETH_FLOW, flow); 836 err += lan78xx_write_reg(sc, ETH_FCT_FLOW, fct_flow); 837 if (err) 838 muge_warn_printf(sc, "media change failed, error %d\n", err); 839 840 done: 841 if (!locked) 842 MUGE_UNLOCK(sc); 843 } 844 845 /* 846 * lan78xx_set_mdix_auto - Configure the device to enable automatic 847 * crossover and polarity detection. LAN7800 provides HP Auto-MDIX 848 * functionality for seamless crossover and polarity detection. 849 * 850 * @sc: driver soft context 851 * 852 * LOCKING: 853 * Takes and releases the device mutex lock if not already held. 854 */ 855 static void 856 lan78xx_set_mdix_auto(struct muge_softc *sc) 857 { 858 uint32_t buf, err; 859 860 err = lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, 861 MUGE_EXT_PAGE_ACCESS, MUGE_EXT_PAGE_SPACE_1); 862 863 buf = lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, 864 MUGE_EXT_MODE_CTRL); 865 buf &= ~MUGE_EXT_MODE_CTRL_MDIX_MASK_; 866 buf |= MUGE_EXT_MODE_CTRL_AUTO_MDIX_; 867 868 lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); 869 err += lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, 870 MUGE_EXT_MODE_CTRL, buf); 871 872 err += lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, 873 MUGE_EXT_PAGE_ACCESS, MUGE_EXT_PAGE_SPACE_0); 874 875 if (err != 0) 876 muge_warn_printf(sc, "error setting PHY's MDIX status\n"); 877 878 sc->sc_mdix_ctl = buf; 879 } 880 881 /** 882 * lan78xx_phy_init - Initialises the in-built MUGE phy 883 * @sc: driver soft context 884 * 885 * Resets the PHY part of the chip and then initialises it to default 886 * values. The 'link down' and 'auto-negotiation complete' interrupts 887 * from the PHY are also enabled, however we don't monitor the interrupt 888 * endpoints for the moment. 889 * 890 * RETURNS: 891 * Returns 0 on success or EIO if failed to reset the PHY. 892 */ 893 static int 894 lan78xx_phy_init(struct muge_softc *sc) 895 { 896 muge_dbg_printf(sc, "Initializing PHY.\n"); 897 uint16_t bmcr, lmsr; 898 usb_ticks_t start_ticks; 899 uint32_t hw_reg; 900 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 901 902 MUGE_LOCK_ASSERT(sc, MA_OWNED); 903 904 /* Reset phy and wait for reset to complete. */ 905 lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, 906 BMCR_RESET); 907 908 start_ticks = ticks; 909 do { 910 uether_pause(&sc->sc_ue, hz / 100); 911 bmcr = lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, 912 MII_BMCR); 913 } while ((bmcr & BMCR_RESET) && ((ticks - start_ticks) < max_ticks)); 914 915 if (((usb_ticks_t)(ticks - start_ticks)) >= max_ticks) { 916 muge_err_printf(sc, "PHY reset timed-out\n"); 917 return (EIO); 918 } 919 920 /* Setup phy to interrupt upon link down or autoneg completion. */ 921 lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, 922 MUGE_PHY_INTR_STAT); 923 lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, 924 MUGE_PHY_INTR_MASK, 925 (MUGE_PHY_INTR_ANEG_COMP | MUGE_PHY_INTR_LINK_CHANGE)); 926 927 /* Enable Auto-MDIX for crossover and polarity detection. */ 928 lan78xx_set_mdix_auto(sc); 929 930 /* Enable all modes. */ 931 lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_ANAR, 932 ANAR_10 | ANAR_10_FD | ANAR_TX | ANAR_TX_FD | 933 ANAR_CSMA | ANAR_FC | ANAR_PAUSE_ASYM); 934 935 /* Restart auto-negotation. */ 936 bmcr |= BMCR_STARTNEG; 937 bmcr |= BMCR_AUTOEN; 938 lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, bmcr); 939 bmcr = lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); 940 941 /* Configure LED Modes. */ 942 if (sc->sc_led_modes_mask != 0) { 943 lmsr = lan78xx_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, 944 MUGE_PHY_LED_MODE); 945 lmsr &= ~sc->sc_led_modes_mask; 946 lmsr |= sc->sc_led_modes; 947 lan78xx_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, 948 MUGE_PHY_LED_MODE, lmsr); 949 } 950 951 /* Enable appropriate LEDs. */ 952 if (sc->sc_leds != 0 && 953 lan78xx_read_reg(sc, ETH_HW_CFG, &hw_reg) == 0) { 954 hw_reg &= ~(ETH_HW_CFG_LEDO_EN_ | ETH_HW_CFG_LED1_EN_ | 955 ETH_HW_CFG_LED2_EN_ | ETH_HW_CFG_LED3_EN_ ); 956 hw_reg |= sc->sc_leds; 957 lan78xx_write_reg(sc, ETH_HW_CFG, hw_reg); 958 } 959 return (0); 960 } 961 962 /** 963 * lan78xx_chip_init - Initialises the chip after power on 964 * @sc: driver soft context 965 * 966 * This initialisation sequence is modelled on the procedure in the Linux 967 * driver. 968 * 969 * RETURNS: 970 * Returns 0 on success or an error code on failure. 971 */ 972 static int 973 lan78xx_chip_init(struct muge_softc *sc) 974 { 975 int err; 976 uint32_t buf; 977 uint32_t burst_cap; 978 979 MUGE_LOCK_ASSERT(sc, MA_OWNED); 980 981 /* Enter H/W config mode. */ 982 lan78xx_write_reg(sc, ETH_HW_CFG, ETH_HW_CFG_LRST_); 983 984 if ((err = lan78xx_wait_for_bits(sc, ETH_HW_CFG, ETH_HW_CFG_LRST_)) != 985 0) { 986 muge_warn_printf(sc, 987 "timed-out waiting for lite reset to complete\n"); 988 goto init_failed; 989 } 990 991 /* Set the mac address. */ 992 if ((err = lan78xx_setmacaddress(sc, sc->sc_ue.ue_eaddr)) != 0) { 993 muge_warn_printf(sc, "failed to set the MAC address\n"); 994 goto init_failed; 995 } 996 997 /* Read and display the revision register. */ 998 if ((err = lan78xx_read_reg(sc, ETH_ID_REV, &buf)) < 0) { 999 muge_warn_printf(sc, "failed to read ETH_ID_REV (err = %d)\n", 1000 err); 1001 goto init_failed; 1002 } 1003 sc->chipid = (buf & ETH_ID_REV_CHIP_ID_MASK_) >> 16; 1004 sc->chiprev = buf & ETH_ID_REV_CHIP_REV_MASK_; 1005 switch (sc->chipid) { 1006 case ETH_ID_REV_CHIP_ID_7800_: 1007 case ETH_ID_REV_CHIP_ID_7850_: 1008 break; 1009 default: 1010 muge_warn_printf(sc, "Chip ID 0x%04x not yet supported\n", 1011 sc->chipid); 1012 goto init_failed; 1013 } 1014 device_printf(sc->sc_ue.ue_dev, "Chip ID 0x%04x rev %04x\n", sc->chipid, 1015 sc->chiprev); 1016 1017 /* Respond to BULK-IN tokens with a NAK when RX FIFO is empty. */ 1018 if ((err = lan78xx_read_reg(sc, ETH_USB_CFG0, &buf)) != 0) { 1019 muge_warn_printf(sc, "failed to read ETH_USB_CFG0 (err=%d)\n", err); 1020 goto init_failed; 1021 } 1022 buf |= ETH_USB_CFG_BIR_; 1023 lan78xx_write_reg(sc, ETH_USB_CFG0, buf); 1024 1025 /* 1026 * XXX LTM support will go here. 1027 */ 1028 1029 /* Configuring the burst cap. */ 1030 switch (usbd_get_speed(sc->sc_ue.ue_udev)) { 1031 case USB_SPEED_SUPER: 1032 burst_cap = MUGE_DEFAULT_BURST_CAP_SIZE/MUGE_SS_USB_PKT_SIZE; 1033 break; 1034 case USB_SPEED_HIGH: 1035 burst_cap = MUGE_DEFAULT_BURST_CAP_SIZE/MUGE_HS_USB_PKT_SIZE; 1036 break; 1037 default: 1038 burst_cap = MUGE_DEFAULT_BURST_CAP_SIZE/MUGE_FS_USB_PKT_SIZE; 1039 } 1040 1041 lan78xx_write_reg(sc, ETH_BURST_CAP, burst_cap); 1042 1043 /* Set the default bulk in delay (same value from Linux driver). */ 1044 lan78xx_write_reg(sc, ETH_BULK_IN_DLY, MUGE_DEFAULT_BULK_IN_DELAY); 1045 1046 /* Multiple ethernet frames per USB packets. */ 1047 err = lan78xx_read_reg(sc, ETH_HW_CFG, &buf); 1048 buf |= ETH_HW_CFG_MEF_; 1049 err = lan78xx_write_reg(sc, ETH_HW_CFG, buf); 1050 1051 /* Enable burst cap. */ 1052 if ((err = lan78xx_read_reg(sc, ETH_USB_CFG0, &buf)) < 0) { 1053 muge_warn_printf(sc, "failed to read ETH_USB_CFG0 (err=%d)\n", 1054 err); 1055 goto init_failed; 1056 } 1057 buf |= ETH_USB_CFG_BCE_; 1058 err = lan78xx_write_reg(sc, ETH_USB_CFG0, buf); 1059 1060 /* 1061 * Set FCL's RX and TX FIFO sizes: according to data sheet this is 1062 * already the default value. But we initialize it to the same value 1063 * anyways, as that's what the Linux driver does. 1064 * 1065 */ 1066 buf = (MUGE_MAX_RX_FIFO_SIZE - 512) / 512; 1067 err = lan78xx_write_reg(sc, ETH_FCT_RX_FIFO_END, buf); 1068 1069 buf = (MUGE_MAX_TX_FIFO_SIZE - 512) / 512; 1070 err = lan78xx_write_reg(sc, ETH_FCT_TX_FIFO_END, buf); 1071 1072 /* Enabling interrupts. (Not using them for now) */ 1073 err = lan78xx_write_reg(sc, ETH_INT_STS, ETH_INT_STS_CLEAR_ALL_); 1074 1075 /* 1076 * Initializing flow control registers to 0. These registers are 1077 * properly set is handled in link-reset function in the Linux driver. 1078 */ 1079 err = lan78xx_write_reg(sc, ETH_FLOW, 0); 1080 err = lan78xx_write_reg(sc, ETH_FCT_FLOW, 0); 1081 1082 /* 1083 * Settings for the RFE, we enable broadcast and destination address 1084 * perfect filtering. 1085 */ 1086 err = lan78xx_read_reg(sc, ETH_RFE_CTL, &buf); 1087 buf |= ETH_RFE_CTL_BCAST_EN_ | ETH_RFE_CTL_DA_PERFECT_; 1088 err = lan78xx_write_reg(sc, ETH_RFE_CTL, buf); 1089 1090 /* 1091 * At this point the Linux driver writes multicast tables, and enables 1092 * checksum engines. But in FreeBSD that gets done in muge_init, 1093 * which gets called when the interface is brought up. 1094 */ 1095 1096 /* Reset the PHY. */ 1097 lan78xx_write_reg(sc, ETH_PMT_CTL, ETH_PMT_CTL_PHY_RST_); 1098 if ((err = lan78xx_wait_for_bits(sc, ETH_PMT_CTL, 1099 ETH_PMT_CTL_PHY_RST_)) != 0) { 1100 muge_warn_printf(sc, 1101 "timed-out waiting for phy reset to complete\n"); 1102 goto init_failed; 1103 } 1104 1105 err = lan78xx_read_reg(sc, ETH_MAC_CR, &buf); 1106 if (sc->chipid == ETH_ID_REV_CHIP_ID_7800_ && 1107 !lan78xx_eeprom_present(sc)) { 1108 /* Set automatic duplex and speed on LAN7800 without EEPROM. */ 1109 buf |= ETH_MAC_CR_AUTO_DUPLEX_ | ETH_MAC_CR_AUTO_SPEED_; 1110 } 1111 err = lan78xx_write_reg(sc, ETH_MAC_CR, buf); 1112 1113 /* 1114 * Enable PHY interrupts (Not really getting used for now) 1115 * ETH_INT_EP_CTL: interrupt endpoint control register 1116 * phy events cause interrupts to be issued 1117 */ 1118 err = lan78xx_read_reg(sc, ETH_INT_EP_CTL, &buf); 1119 buf |= ETH_INT_ENP_PHY_INT; 1120 err = lan78xx_write_reg(sc, ETH_INT_EP_CTL, buf); 1121 1122 /* 1123 * Enables mac's transmitter. It will transmit frames from the buffer 1124 * onto the cable. 1125 */ 1126 err = lan78xx_read_reg(sc, ETH_MAC_TX, &buf); 1127 buf |= ETH_MAC_TX_TXEN_; 1128 err = lan78xx_write_reg(sc, ETH_MAC_TX, buf); 1129 1130 /* FIFO is capable of transmitting frames to MAC. */ 1131 err = lan78xx_read_reg(sc, ETH_FCT_TX_CTL, &buf); 1132 buf |= ETH_FCT_TX_CTL_EN_; 1133 err = lan78xx_write_reg(sc, ETH_FCT_TX_CTL, buf); 1134 1135 /* 1136 * Set max frame length. In linux this is dev->mtu (which by default 1137 * is 1500) + VLAN_ETH_HLEN = 1518. 1138 */ 1139 err = lan78xx_set_rx_max_frame_length(sc, ETHER_MAX_LEN); 1140 1141 /* Initialise the PHY. */ 1142 if ((err = lan78xx_phy_init(sc)) != 0) 1143 goto init_failed; 1144 1145 /* Enable MAC RX. */ 1146 err = lan78xx_read_reg(sc, ETH_MAC_RX, &buf); 1147 buf |= ETH_MAC_RX_EN_; 1148 err = lan78xx_write_reg(sc, ETH_MAC_RX, buf); 1149 1150 /* Enable FIFO controller RX. */ 1151 err = lan78xx_read_reg(sc, ETH_FCT_RX_CTL, &buf); 1152 buf |= ETH_FCT_TX_CTL_EN_; 1153 err = lan78xx_write_reg(sc, ETH_FCT_RX_CTL, buf); 1154 1155 sc->sc_flags |= MUGE_FLAG_INIT_DONE; 1156 return (0); 1157 1158 init_failed: 1159 muge_err_printf(sc, "lan78xx_chip_init failed (err=%d)\n", err); 1160 return (err); 1161 } 1162 1163 static void 1164 muge_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) 1165 { 1166 struct muge_softc *sc = usbd_xfer_softc(xfer); 1167 struct usb_ether *ue = &sc->sc_ue; 1168 struct ifnet *ifp = uether_getifp(ue); 1169 struct mbuf *m; 1170 struct usb_page_cache *pc; 1171 uint32_t rx_cmd_a, rx_cmd_b; 1172 uint16_t rx_cmd_c; 1173 int pktlen; 1174 int off; 1175 int actlen; 1176 1177 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 1178 muge_dbg_printf(sc, "rx : actlen %d\n", actlen); 1179 1180 switch (USB_GET_STATE(xfer)) { 1181 case USB_ST_TRANSFERRED: 1182 /* 1183 * There is always a zero length frame after bringing the 1184 * interface up. 1185 */ 1186 if (actlen < (sizeof(rx_cmd_a) + ETHER_CRC_LEN)) 1187 goto tr_setup; 1188 1189 /* 1190 * There may be multiple packets in the USB frame. Each will 1191 * have a header and each needs to have its own mbuf allocated 1192 * and populated for it. 1193 */ 1194 pc = usbd_xfer_get_frame(xfer, 0); 1195 off = 0; 1196 1197 while (off < actlen) { 1198 /* The frame header is aligned on a 4 byte boundary. */ 1199 off = ((off + 0x3) & ~0x3); 1200 1201 /* Extract RX CMD A. */ 1202 if (off + sizeof(rx_cmd_a) > actlen) 1203 goto tr_setup; 1204 usbd_copy_out(pc, off, &rx_cmd_a, sizeof(rx_cmd_a)); 1205 off += (sizeof(rx_cmd_a)); 1206 rx_cmd_a = le32toh(rx_cmd_a); 1207 1208 /* Extract RX CMD B. */ 1209 if (off + sizeof(rx_cmd_b) > actlen) 1210 goto tr_setup; 1211 usbd_copy_out(pc, off, &rx_cmd_b, sizeof(rx_cmd_b)); 1212 off += (sizeof(rx_cmd_b)); 1213 rx_cmd_b = le32toh(rx_cmd_b); 1214 1215 /* Extract RX CMD C. */ 1216 if (off + sizeof(rx_cmd_c) > actlen) 1217 goto tr_setup; 1218 usbd_copy_out(pc, off, &rx_cmd_c, sizeof(rx_cmd_c)); 1219 off += (sizeof(rx_cmd_c)); 1220 rx_cmd_c = le16toh(rx_cmd_c); 1221 1222 if (off > actlen) 1223 goto tr_setup; 1224 1225 pktlen = (rx_cmd_a & RX_CMD_A_LEN_MASK_); 1226 1227 muge_dbg_printf(sc, 1228 "rx_cmd_a 0x%08x rx_cmd_b 0x%08x rx_cmd_c 0x%04x " 1229 " pktlen %d actlen %d off %d\n", 1230 rx_cmd_a, rx_cmd_b, rx_cmd_c, pktlen, actlen, off); 1231 1232 if (rx_cmd_a & RX_CMD_A_RED_) { 1233 muge_dbg_printf(sc, 1234 "rx error (hdr 0x%08x)\n", rx_cmd_a); 1235 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 1236 } else { 1237 /* Ethernet frame too big or too small? */ 1238 if ((pktlen < ETHER_HDR_LEN) || 1239 (pktlen > (actlen - off))) 1240 goto tr_setup; 1241 1242 /* Create a new mbuf to store the packet. */ 1243 m = uether_newbuf(); 1244 if (m == NULL) { 1245 muge_warn_printf(sc, 1246 "failed to create new mbuf\n"); 1247 if_inc_counter(ifp, IFCOUNTER_IQDROPS, 1248 1); 1249 goto tr_setup; 1250 } 1251 if (pktlen > m->m_len) { 1252 muge_dbg_printf(sc, 1253 "buffer too small %d vs %d bytes", 1254 pktlen, m->m_len); 1255 if_inc_counter(ifp, IFCOUNTER_IQDROPS, 1); 1256 m_freem(m); 1257 goto tr_setup; 1258 } 1259 usbd_copy_out(pc, off, mtod(m, uint8_t *), 1260 pktlen); 1261 1262 /* 1263 * Check if RX checksums are computed, and 1264 * offload them 1265 */ 1266 if ((ifp->if_capenable & IFCAP_RXCSUM) && 1267 !(rx_cmd_a & RX_CMD_A_ICSM_)) { 1268 struct ether_header *eh; 1269 eh = mtod(m, struct ether_header *); 1270 /* 1271 * Remove the extra 2 bytes of the csum 1272 * 1273 * The checksum appears to be 1274 * simplistically calculated over the 1275 * protocol headers up to the end of the 1276 * eth frame. Which means if the eth 1277 * frame is padded the csum calculation 1278 * is incorrectly performed over the 1279 * padding bytes as well. Therefore to 1280 * be safe we ignore the H/W csum on 1281 * frames less than or equal to 1282 * 64 bytes. 1283 * 1284 * Protocols checksummed: 1285 * TCP, UDP, ICMP, IGMP, IP 1286 */ 1287 if (pktlen > ETHER_MIN_LEN) { 1288 m->m_pkthdr.csum_flags |= 1289 CSUM_DATA_VALID | 1290 CSUM_PSEUDO_HDR; 1291 1292 /* 1293 * Copy the checksum from the 1294 * last 2 bytes of the transfer 1295 * and put in the csum_data 1296 * field. 1297 */ 1298 usbd_copy_out(pc, 1299 (off + pktlen), 1300 &m->m_pkthdr.csum_data, 2); 1301 1302 /* 1303 * The data is copied in network 1304 * order, but the csum algorithm 1305 * in the kernel expects it to 1306 * be in host network order. 1307 */ 1308 m->m_pkthdr.csum_data = 1309 ntohs(0xffff); 1310 1311 muge_dbg_printf(sc, 1312 "RX checksum offloaded (0x%04x)\n", 1313 m->m_pkthdr.csum_data); 1314 } 1315 } 1316 1317 /* Enqueue the mbuf on the receive queue. */ 1318 if (pktlen < (4 + ETHER_HDR_LEN)) { 1319 m_freem(m); 1320 goto tr_setup; 1321 } 1322 /* Remove 4 trailing bytes */ 1323 uether_rxmbuf(ue, m, pktlen - 4); 1324 } 1325 1326 /* 1327 * Update the offset to move to the next potential 1328 * packet. 1329 */ 1330 off += pktlen; 1331 } 1332 /* FALLTHROUGH */ 1333 case USB_ST_SETUP: 1334 tr_setup: 1335 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 1336 usbd_transfer_submit(xfer); 1337 uether_rxflush(ue); 1338 return; 1339 default: 1340 if (error != USB_ERR_CANCELLED) { 1341 muge_warn_printf(sc, "bulk read error, %s\n", 1342 usbd_errstr(error)); 1343 usbd_xfer_set_stall(xfer); 1344 goto tr_setup; 1345 } 1346 return; 1347 } 1348 } 1349 1350 /** 1351 * muge_bulk_write_callback - Write callback used to send ethernet frame(s) 1352 * @xfer: the USB transfer 1353 * @error: error code if the transfers is in an errored state 1354 * 1355 * The main write function that pulls ethernet frames off the queue and 1356 * sends them out. 1357 * 1358 */ 1359 static void 1360 muge_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) 1361 { 1362 struct muge_softc *sc = usbd_xfer_softc(xfer); 1363 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 1364 struct usb_page_cache *pc; 1365 struct mbuf *m; 1366 int nframes; 1367 uint32_t frm_len = 0, tx_cmd_a = 0, tx_cmd_b = 0; 1368 1369 switch (USB_GET_STATE(xfer)) { 1370 case USB_ST_TRANSFERRED: 1371 muge_dbg_printf(sc, 1372 "USB TRANSFER status: USB_ST_TRANSFERRED\n"); 1373 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1374 /* FALLTHROUGH */ 1375 case USB_ST_SETUP: 1376 muge_dbg_printf(sc, "USB TRANSFER status: USB_ST_SETUP\n"); 1377 tr_setup: 1378 if ((sc->sc_flags & MUGE_FLAG_LINK) == 0 || 1379 (ifp->if_drv_flags & IFF_DRV_OACTIVE) != 0) { 1380 muge_dbg_printf(sc, 1381 "sc->sc_flags & MUGE_FLAG_LINK: %d\n", 1382 (sc->sc_flags & MUGE_FLAG_LINK)); 1383 muge_dbg_printf(sc, 1384 "ifp->if_drv_flags & IFF_DRV_OACTIVE: %d\n", 1385 (ifp->if_drv_flags & IFF_DRV_OACTIVE)); 1386 muge_dbg_printf(sc, 1387 "USB TRANSFER not sending: no link or controller is busy \n"); 1388 /* 1389 * Don't send anything if there is no link or 1390 * controller is busy. 1391 */ 1392 return; 1393 } 1394 for (nframes = 0; 1395 nframes < 16 && !IFQ_DRV_IS_EMPTY(&ifp->if_snd); 1396 nframes++) { 1397 IFQ_DRV_DEQUEUE(&ifp->if_snd, m); 1398 if (m == NULL) 1399 break; 1400 usbd_xfer_set_frame_offset(xfer, nframes * MCLBYTES, 1401 nframes); 1402 frm_len = 0; 1403 pc = usbd_xfer_get_frame(xfer, nframes); 1404 1405 /* 1406 * Each frame is prefixed with two 32-bit values 1407 * describing the length of the packet and buffer. 1408 */ 1409 tx_cmd_a = (m->m_pkthdr.len & TX_CMD_A_LEN_MASK_) | 1410 TX_CMD_A_FCS_; 1411 tx_cmd_a = htole32(tx_cmd_a); 1412 usbd_copy_in(pc, 0, &tx_cmd_a, sizeof(tx_cmd_a)); 1413 1414 tx_cmd_b = 0; 1415 1416 /* TCP LSO Support will probably be implemented here. */ 1417 tx_cmd_b = htole32(tx_cmd_b); 1418 usbd_copy_in(pc, 4, &tx_cmd_b, sizeof(tx_cmd_b)); 1419 1420 frm_len += 8; 1421 1422 /* Next copy in the actual packet */ 1423 usbd_m_copy_in(pc, frm_len, m, 0, m->m_pkthdr.len); 1424 frm_len += m->m_pkthdr.len; 1425 1426 if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1); 1427 1428 /* 1429 * If there's a BPF listener, bounce a copy of this 1430 * frame to it. 1431 */ 1432 BPF_MTAP(ifp, m); 1433 m_freem(m); 1434 1435 /* Set frame length. */ 1436 usbd_xfer_set_frame_len(xfer, nframes, frm_len); 1437 } 1438 1439 muge_dbg_printf(sc, "USB TRANSFER nframes: %d\n", nframes); 1440 if (nframes != 0) { 1441 muge_dbg_printf(sc, "USB TRANSFER submit attempt\n"); 1442 usbd_xfer_set_frames(xfer, nframes); 1443 usbd_transfer_submit(xfer); 1444 ifp->if_drv_flags |= IFF_DRV_OACTIVE; 1445 } 1446 return; 1447 1448 default: 1449 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1); 1450 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1451 1452 if (error != USB_ERR_CANCELLED) { 1453 muge_err_printf(sc, 1454 "usb error on tx: %s\n", usbd_errstr(error)); 1455 usbd_xfer_set_stall(xfer); 1456 goto tr_setup; 1457 } 1458 return; 1459 } 1460 } 1461 1462 /** 1463 * muge_set_mac_addr - Initiailizes NIC MAC address 1464 * @ue: the USB ethernet device 1465 * 1466 * Tries to obtain MAC address from number of sources: registers, 1467 * EEPROM, DTB blob. If all sources fail - generates random MAC. 1468 */ 1469 static void 1470 muge_set_mac_addr(struct usb_ether *ue) 1471 { 1472 struct muge_softc *sc = uether_getsc(ue); 1473 uint32_t mac_h, mac_l; 1474 1475 memset(ue->ue_eaddr, 0xff, ETHER_ADDR_LEN); 1476 1477 uint32_t val; 1478 lan78xx_read_reg(sc, 0, &val); 1479 1480 /* Read current MAC address from RX_ADDRx registers. */ 1481 if ((lan78xx_read_reg(sc, ETH_RX_ADDRL, &mac_l) == 0) && 1482 (lan78xx_read_reg(sc, ETH_RX_ADDRH, &mac_h) == 0)) { 1483 ue->ue_eaddr[5] = (uint8_t)((mac_h >> 8) & 0xff); 1484 ue->ue_eaddr[4] = (uint8_t)((mac_h) & 0xff); 1485 ue->ue_eaddr[3] = (uint8_t)((mac_l >> 24) & 0xff); 1486 ue->ue_eaddr[2] = (uint8_t)((mac_l >> 16) & 0xff); 1487 ue->ue_eaddr[1] = (uint8_t)((mac_l >> 8) & 0xff); 1488 ue->ue_eaddr[0] = (uint8_t)((mac_l) & 0xff); 1489 } 1490 1491 /* 1492 * If RX_ADDRx did not provide a valid MAC address, try EEPROM. If that 1493 * doesn't work, try OTP. Whether any of these methods work or not, try 1494 * FDT data, because it is allowed to override the EEPROM/OTP values. 1495 */ 1496 if (ETHER_IS_VALID(ue->ue_eaddr)) { 1497 muge_dbg_printf(sc, "MAC assigned from registers\n"); 1498 } else if (lan78xx_eeprom_present(sc) && lan78xx_eeprom_read_raw(sc, 1499 ETH_E2P_MAC_OFFSET, ue->ue_eaddr, ETHER_ADDR_LEN) == 0 && 1500 ETHER_IS_VALID(ue->ue_eaddr)) { 1501 muge_dbg_printf(sc, "MAC assigned from EEPROM\n"); 1502 } else if (lan78xx_otp_read(sc, OTP_MAC_OFFSET, ue->ue_eaddr, 1503 ETHER_ADDR_LEN) == 0 && ETHER_IS_VALID(ue->ue_eaddr)) { 1504 muge_dbg_printf(sc, "MAC assigned from OTP\n"); 1505 } 1506 1507 #ifdef FDT 1508 /* ue->ue_eaddr modified only if config exists for this dev instance. */ 1509 usb_fdt_get_mac_addr(ue->ue_dev, ue); 1510 if (ETHER_IS_VALID(ue->ue_eaddr)) { 1511 muge_dbg_printf(sc, "MAC assigned from FDT data\n"); 1512 } 1513 #endif 1514 1515 if (!ETHER_IS_VALID(ue->ue_eaddr)) { 1516 muge_dbg_printf(sc, "MAC assigned randomly\n"); 1517 arc4rand(ue->ue_eaddr, ETHER_ADDR_LEN, 0); 1518 ue->ue_eaddr[0] &= ~0x01; /* unicast */ 1519 ue->ue_eaddr[0] |= 0x02; /* locally administered */ 1520 } 1521 } 1522 1523 /** 1524 * muge_set_leds - Initializes NIC LEDs pattern 1525 * @ue: the USB ethernet device 1526 * 1527 * Tries to store the LED modes. 1528 * Supports only DTB blob like the Linux driver does. 1529 */ 1530 static void 1531 muge_set_leds(struct usb_ether *ue) 1532 { 1533 #ifdef FDT 1534 struct muge_softc *sc = uether_getsc(ue); 1535 phandle_t node; 1536 pcell_t modes[4]; /* 4 LEDs are possible */ 1537 ssize_t proplen; 1538 uint32_t count; 1539 1540 if ((node = usb_fdt_get_node(ue->ue_dev, ue->ue_udev)) != -1 && 1541 (proplen = OF_getencprop(node, "microchip,led-modes", modes, 1542 sizeof(modes))) > 0) { 1543 count = proplen / sizeof( uint32_t ); 1544 sc->sc_leds = (count > 0) * ETH_HW_CFG_LEDO_EN_ | 1545 (count > 1) * ETH_HW_CFG_LED1_EN_ | 1546 (count > 2) * ETH_HW_CFG_LED2_EN_ | 1547 (count > 3) * ETH_HW_CFG_LED3_EN_; 1548 while (count-- > 0) { 1549 sc->sc_led_modes |= (modes[count] & 0xf) << (4 * count); 1550 sc->sc_led_modes_mask |= 0xf << (4 * count); 1551 } 1552 muge_dbg_printf(sc, "LED modes set from FDT data\n"); 1553 } 1554 #endif 1555 } 1556 1557 /** 1558 * muge_attach_post - Called after the driver attached to the USB interface 1559 * @ue: the USB ethernet device 1560 * 1561 * This is where the chip is intialised for the first time. This is 1562 * different from the muge_init() function in that that one is designed to 1563 * setup the H/W to match the UE settings and can be called after a reset. 1564 * 1565 */ 1566 static void 1567 muge_attach_post(struct usb_ether *ue) 1568 { 1569 struct muge_softc *sc = uether_getsc(ue); 1570 1571 muge_dbg_printf(sc, "Calling muge_attach_post.\n"); 1572 1573 /* Setup some of the basics */ 1574 sc->sc_phyno = 1; 1575 1576 muge_set_mac_addr(ue); 1577 muge_set_leds(ue); 1578 1579 /* Initialise the chip for the first time */ 1580 lan78xx_chip_init(sc); 1581 } 1582 1583 /** 1584 * muge_attach_post_sub - Called after attach to the USB interface 1585 * @ue: the USB ethernet device 1586 * 1587 * Most of this is boilerplate code and copied from the base USB ethernet 1588 * driver. It has been overriden so that we can indicate to the system 1589 * that the chip supports H/W checksumming. 1590 * 1591 * RETURNS: 1592 * Returns 0 on success or a negative error code. 1593 */ 1594 static int 1595 muge_attach_post_sub(struct usb_ether *ue) 1596 { 1597 struct muge_softc *sc; 1598 struct ifnet *ifp; 1599 int error; 1600 1601 sc = uether_getsc(ue); 1602 muge_dbg_printf(sc, "Calling muge_attach_post_sub.\n"); 1603 ifp = ue->ue_ifp; 1604 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 1605 ifp->if_start = uether_start; 1606 ifp->if_ioctl = muge_ioctl; 1607 ifp->if_init = uether_init; 1608 IFQ_SET_MAXLEN(&ifp->if_snd, ifqmaxlen); 1609 ifp->if_snd.ifq_drv_maxlen = ifqmaxlen; 1610 IFQ_SET_READY(&ifp->if_snd); 1611 1612 /* 1613 * The chip supports TCP/UDP checksum offloading on TX and RX paths, 1614 * however currently only RX checksum is supported in the driver 1615 * (see top of file). 1616 */ 1617 ifp->if_capabilities |= IFCAP_VLAN_MTU; 1618 ifp->if_hwassist = 0; 1619 ifp->if_capabilities |= IFCAP_RXCSUM; 1620 1621 if (MUGE_DEFAULT_TX_CSUM_ENABLE) 1622 ifp->if_capabilities |= IFCAP_TXCSUM; 1623 1624 /* 1625 * In the Linux driver they also enable scatter/gather (NETIF_F_SG) 1626 * here, that's something related to socket buffers used in Linux. 1627 * FreeBSD doesn't have that as an interface feature. 1628 */ 1629 if (MUGE_DEFAULT_TSO_ENABLE) 1630 ifp->if_capabilities |= IFCAP_TSO4 | IFCAP_TSO6; 1631 1632 #if 0 1633 /* TX checksuming is disabled since not yet implemented. */ 1634 ifp->if_capabilities |= IFCAP_TXCSUM; 1635 ifp->if_capenable |= IFCAP_TXCSUM; 1636 ifp->if_hwassist = CSUM_TCP | CSUM_UDP; 1637 #endif 1638 1639 ifp->if_capenable = ifp->if_capabilities; 1640 1641 mtx_lock(&Giant); 1642 error = mii_attach(ue->ue_dev, &ue->ue_miibus, ifp, uether_ifmedia_upd, 1643 ue->ue_methods->ue_mii_sts, BMSR_DEFCAPMASK, sc->sc_phyno, 1644 MII_OFFSET_ANY, 0); 1645 mtx_unlock(&Giant); 1646 1647 return (0); 1648 } 1649 1650 /** 1651 * muge_start - Starts communication with the LAN78xx chip 1652 * @ue: USB ether interface 1653 */ 1654 static void 1655 muge_start(struct usb_ether *ue) 1656 { 1657 struct muge_softc *sc = uether_getsc(ue); 1658 1659 /* 1660 * Start the USB transfers, if not already started. 1661 */ 1662 usbd_transfer_start(sc->sc_xfer[MUGE_BULK_DT_RD]); 1663 usbd_transfer_start(sc->sc_xfer[MUGE_BULK_DT_WR]); 1664 } 1665 1666 /** 1667 * muge_ioctl - ioctl function for the device 1668 * @ifp: interface pointer 1669 * @cmd: the ioctl command 1670 * @data: data passed in the ioctl call, typically a pointer to struct 1671 * ifreq. 1672 * 1673 * The ioctl routine is overridden to detect change requests for the H/W 1674 * checksum capabilities. 1675 * 1676 * RETURNS: 1677 * 0 on success and an error code on failure. 1678 */ 1679 static int 1680 muge_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data) 1681 { 1682 struct usb_ether *ue = ifp->if_softc; 1683 struct muge_softc *sc; 1684 struct ifreq *ifr; 1685 int rc; 1686 int mask; 1687 int reinit; 1688 1689 if (cmd == SIOCSIFCAP) { 1690 sc = uether_getsc(ue); 1691 ifr = (struct ifreq *)data; 1692 1693 MUGE_LOCK(sc); 1694 1695 rc = 0; 1696 reinit = 0; 1697 1698 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 1699 1700 /* Modify the RX CSUM enable bits. */ 1701 if ((mask & IFCAP_RXCSUM) != 0 && 1702 (ifp->if_capabilities & IFCAP_RXCSUM) != 0) { 1703 ifp->if_capenable ^= IFCAP_RXCSUM; 1704 1705 if (ifp->if_drv_flags & IFF_DRV_RUNNING) { 1706 ifp->if_drv_flags &= ~IFF_DRV_RUNNING; 1707 reinit = 1; 1708 } 1709 } 1710 1711 MUGE_UNLOCK(sc); 1712 if (reinit) 1713 uether_init(ue); 1714 } else { 1715 rc = uether_ioctl(ifp, cmd, data); 1716 } 1717 1718 return (rc); 1719 } 1720 1721 /** 1722 * muge_reset - Reset the SMSC chip 1723 * @sc: device soft context 1724 * 1725 * LOCKING: 1726 * Should be called with the SMSC lock held. 1727 */ 1728 static void 1729 muge_reset(struct muge_softc *sc) 1730 { 1731 struct usb_config_descriptor *cd; 1732 usb_error_t err; 1733 1734 cd = usbd_get_config_descriptor(sc->sc_ue.ue_udev); 1735 1736 err = usbd_req_set_config(sc->sc_ue.ue_udev, &sc->sc_mtx, 1737 cd->bConfigurationValue); 1738 if (err) 1739 muge_warn_printf(sc, "reset failed (ignored)\n"); 1740 1741 /* Wait a little while for the chip to get its brains in order. */ 1742 uether_pause(&sc->sc_ue, hz / 100); 1743 1744 /* Reinitialize controller to achieve full reset. */ 1745 lan78xx_chip_init(sc); 1746 } 1747 1748 /** 1749 * muge_set_addr_filter 1750 * 1751 * @sc: device soft context 1752 * @index: index of the entry to the perfect address table 1753 * @addr: address to be written 1754 * 1755 */ 1756 static void 1757 muge_set_addr_filter(struct muge_softc *sc, int index, 1758 uint8_t addr[ETHER_ADDR_LEN]) 1759 { 1760 uint32_t tmp; 1761 1762 if ((sc) && (index > 0) && (index < MUGE_NUM_PFILTER_ADDRS_)) { 1763 tmp = addr[3]; 1764 tmp |= addr[2] | (tmp << 8); 1765 tmp |= addr[1] | (tmp << 8); 1766 tmp |= addr[0] | (tmp << 8); 1767 sc->sc_pfilter_table[index][1] = tmp; 1768 tmp = addr[5]; 1769 tmp |= addr[4] | (tmp << 8); 1770 tmp |= ETH_MAF_HI_VALID_ | ETH_MAF_HI_TYPE_DST_; 1771 sc->sc_pfilter_table[index][0] = tmp; 1772 } 1773 } 1774 1775 /** 1776 * lan78xx_dataport_write - write to the selected RAM 1777 * @sc: The device soft context. 1778 * @ram_select: Select which RAM to access. 1779 * @addr: Starting address to write to. 1780 * @buf: word-sized buffer to write to RAM, starting at @addr. 1781 * @length: length of @buf 1782 * 1783 * 1784 * RETURNS: 1785 * 0 if write successful. 1786 */ 1787 static int 1788 lan78xx_dataport_write(struct muge_softc *sc, uint32_t ram_select, 1789 uint32_t addr, uint32_t length, uint32_t *buf) 1790 { 1791 uint32_t dp_sel; 1792 int i, ret; 1793 1794 MUGE_LOCK_ASSERT(sc, MA_OWNED); 1795 ret = lan78xx_wait_for_bits(sc, ETH_DP_SEL, ETH_DP_SEL_DPRDY_); 1796 if (ret < 0) 1797 goto done; 1798 1799 ret = lan78xx_read_reg(sc, ETH_DP_SEL, &dp_sel); 1800 1801 dp_sel &= ~ETH_DP_SEL_RSEL_MASK_; 1802 dp_sel |= ram_select; 1803 1804 ret = lan78xx_write_reg(sc, ETH_DP_SEL, dp_sel); 1805 1806 for (i = 0; i < length; i++) { 1807 ret = lan78xx_write_reg(sc, ETH_DP_ADDR, addr + i); 1808 ret = lan78xx_write_reg(sc, ETH_DP_DATA, buf[i]); 1809 ret = lan78xx_write_reg(sc, ETH_DP_CMD, ETH_DP_CMD_WRITE_); 1810 ret = lan78xx_wait_for_bits(sc, ETH_DP_SEL, ETH_DP_SEL_DPRDY_); 1811 if (ret != 0) 1812 goto done; 1813 } 1814 1815 done: 1816 return (ret); 1817 } 1818 1819 /** 1820 * muge_multicast_write 1821 * @sc: device's soft context 1822 * 1823 * Writes perfect addres filters and hash address filters to their 1824 * corresponding registers and RAMs. 1825 * 1826 */ 1827 static void 1828 muge_multicast_write(struct muge_softc *sc) 1829 { 1830 int i, ret; 1831 lan78xx_dataport_write(sc, ETH_DP_SEL_RSEL_VLAN_DA_, 1832 ETH_DP_SEL_VHF_VLAN_LEN, ETH_DP_SEL_VHF_HASH_LEN, 1833 sc->sc_mchash_table); 1834 1835 for (i = 1; i < MUGE_NUM_PFILTER_ADDRS_; i++) { 1836 ret = lan78xx_write_reg(sc, PFILTER_HI(i), 0); 1837 ret = lan78xx_write_reg(sc, PFILTER_LO(i), 1838 sc->sc_pfilter_table[i][1]); 1839 ret = lan78xx_write_reg(sc, PFILTER_HI(i), 1840 sc->sc_pfilter_table[i][0]); 1841 } 1842 } 1843 1844 /** 1845 * muge_hash - Calculate the hash of a mac address 1846 * @addr: The mac address to calculate the hash on 1847 * 1848 * This function is used when configuring a range of multicast mac 1849 * addresses to filter on. The hash of the mac address is put in the 1850 * device's mac hash table. 1851 * 1852 * RETURNS: 1853 * Returns a value from 0-63 value which is the hash of the mac address. 1854 */ 1855 static inline uint32_t 1856 muge_hash(uint8_t addr[ETHER_ADDR_LEN]) 1857 { 1858 return (ether_crc32_be(addr, ETHER_ADDR_LEN) >> 23) & 0x1ff; 1859 } 1860 1861 static u_int 1862 muge_hash_maddr(void *arg, struct sockaddr_dl *sdl, u_int cnt) 1863 { 1864 struct muge_softc *sc = arg; 1865 uint32_t bitnum; 1866 1867 /* First fill up the perfect address table. */ 1868 if (cnt < 32 /* XXX */) 1869 muge_set_addr_filter(sc, cnt + 1, LLADDR(sdl)); 1870 else { 1871 bitnum = muge_hash(LLADDR(sdl)); 1872 sc->sc_mchash_table[bitnum / 32] |= (1 << (bitnum % 32)); 1873 sc->sc_rfe_ctl |= ETH_RFE_CTL_MCAST_HASH_; 1874 } 1875 1876 return (1); 1877 } 1878 1879 /** 1880 * muge_setmulti - Setup multicast 1881 * @ue: usb ethernet device context 1882 * 1883 * Tells the device to either accept frames with a multicast mac address, 1884 * a select group of m'cast mac addresses or just the devices mac address. 1885 * 1886 * LOCKING: 1887 * Should be called with the MUGE lock held. 1888 */ 1889 static void 1890 muge_setmulti(struct usb_ether *ue) 1891 { 1892 struct muge_softc *sc = uether_getsc(ue); 1893 struct ifnet *ifp = uether_getifp(ue); 1894 uint8_t i; 1895 1896 MUGE_LOCK_ASSERT(sc, MA_OWNED); 1897 1898 sc->sc_rfe_ctl &= ~(ETH_RFE_CTL_UCAST_EN_ | ETH_RFE_CTL_MCAST_EN_ | 1899 ETH_RFE_CTL_DA_PERFECT_ | ETH_RFE_CTL_MCAST_HASH_); 1900 1901 /* Initialize hash filter table. */ 1902 for (i = 0; i < ETH_DP_SEL_VHF_HASH_LEN; i++) 1903 sc->sc_mchash_table[i] = 0; 1904 1905 /* Initialize perfect filter table. */ 1906 for (i = 1; i < MUGE_NUM_PFILTER_ADDRS_; i++) { 1907 sc->sc_pfilter_table[i][0] = sc->sc_pfilter_table[i][1] = 0; 1908 } 1909 1910 sc->sc_rfe_ctl |= ETH_RFE_CTL_BCAST_EN_; 1911 1912 if (ifp->if_flags & IFF_PROMISC) { 1913 muge_dbg_printf(sc, "promiscuous mode enabled\n"); 1914 sc->sc_rfe_ctl |= ETH_RFE_CTL_MCAST_EN_ | ETH_RFE_CTL_UCAST_EN_; 1915 } else if (ifp->if_flags & IFF_ALLMULTI) { 1916 muge_dbg_printf(sc, "receive all multicast enabled\n"); 1917 sc->sc_rfe_ctl |= ETH_RFE_CTL_MCAST_EN_; 1918 } else { 1919 if_foreach_llmaddr(ifp, muge_hash_maddr, sc); 1920 muge_multicast_write(sc); 1921 } 1922 lan78xx_write_reg(sc, ETH_RFE_CTL, sc->sc_rfe_ctl); 1923 } 1924 1925 /** 1926 * muge_setpromisc - Enables/disables promiscuous mode 1927 * @ue: usb ethernet device context 1928 * 1929 * LOCKING: 1930 * Should be called with the MUGE lock held. 1931 */ 1932 static void 1933 muge_setpromisc(struct usb_ether *ue) 1934 { 1935 struct muge_softc *sc = uether_getsc(ue); 1936 struct ifnet *ifp = uether_getifp(ue); 1937 1938 muge_dbg_printf(sc, "promiscuous mode %sabled\n", 1939 (ifp->if_flags & IFF_PROMISC) ? "en" : "dis"); 1940 1941 MUGE_LOCK_ASSERT(sc, MA_OWNED); 1942 1943 if (ifp->if_flags & IFF_PROMISC) 1944 sc->sc_rfe_ctl |= ETH_RFE_CTL_MCAST_EN_ | ETH_RFE_CTL_UCAST_EN_; 1945 else 1946 sc->sc_rfe_ctl &= ~(ETH_RFE_CTL_MCAST_EN_); 1947 1948 lan78xx_write_reg(sc, ETH_RFE_CTL, sc->sc_rfe_ctl); 1949 } 1950 1951 /** 1952 * muge_sethwcsum - Enable or disable H/W UDP and TCP checksumming 1953 * @sc: driver soft context 1954 * 1955 * LOCKING: 1956 * Should be called with the MUGE lock held. 1957 * 1958 * RETURNS: 1959 * Returns 0 on success or a negative error code. 1960 */ 1961 static int 1962 muge_sethwcsum(struct muge_softc *sc) 1963 { 1964 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 1965 int err; 1966 1967 if (!ifp) 1968 return (-EIO); 1969 1970 MUGE_LOCK_ASSERT(sc, MA_OWNED); 1971 1972 if (ifp->if_capenable & IFCAP_RXCSUM) { 1973 sc->sc_rfe_ctl |= ETH_RFE_CTL_IGMP_COE_ | ETH_RFE_CTL_ICMP_COE_; 1974 sc->sc_rfe_ctl |= ETH_RFE_CTL_TCPUDP_COE_ | ETH_RFE_CTL_IP_COE_; 1975 } else { 1976 sc->sc_rfe_ctl &= 1977 ~(ETH_RFE_CTL_IGMP_COE_ | ETH_RFE_CTL_ICMP_COE_); 1978 sc->sc_rfe_ctl &= 1979 ~(ETH_RFE_CTL_TCPUDP_COE_ | ETH_RFE_CTL_IP_COE_); 1980 } 1981 1982 sc->sc_rfe_ctl &= ~ETH_RFE_CTL_VLAN_FILTER_; 1983 1984 err = lan78xx_write_reg(sc, ETH_RFE_CTL, sc->sc_rfe_ctl); 1985 1986 if (err != 0) { 1987 muge_warn_printf(sc, "failed to write ETH_RFE_CTL (err=%d)\n", 1988 err); 1989 return (err); 1990 } 1991 1992 return (0); 1993 } 1994 1995 /** 1996 * muge_ifmedia_upd - Set media options 1997 * @ifp: interface pointer 1998 * 1999 * Basically boilerplate code that simply calls the mii functions to set 2000 * the media options. 2001 * 2002 * LOCKING: 2003 * The device lock must be held before this function is called. 2004 * 2005 * RETURNS: 2006 * Returns 0 on success or a negative error code. 2007 */ 2008 static int 2009 muge_ifmedia_upd(struct ifnet *ifp) 2010 { 2011 struct muge_softc *sc = ifp->if_softc; 2012 muge_dbg_printf(sc, "Calling muge_ifmedia_upd.\n"); 2013 struct mii_data *mii = uether_getmii(&sc->sc_ue); 2014 struct mii_softc *miisc; 2015 int err; 2016 2017 MUGE_LOCK_ASSERT(sc, MA_OWNED); 2018 2019 LIST_FOREACH(miisc, &mii->mii_phys, mii_list) 2020 PHY_RESET(miisc); 2021 err = mii_mediachg(mii); 2022 return (err); 2023 } 2024 2025 /** 2026 * muge_init - Initialises the LAN95xx chip 2027 * @ue: USB ether interface 2028 * 2029 * Called when the interface is brought up (i.e. ifconfig ue0 up), this 2030 * initialise the interface and the rx/tx pipes. 2031 * 2032 * LOCKING: 2033 * Should be called with the MUGE lock held. 2034 */ 2035 static void 2036 muge_init(struct usb_ether *ue) 2037 { 2038 struct muge_softc *sc = uether_getsc(ue); 2039 muge_dbg_printf(sc, "Calling muge_init.\n"); 2040 struct ifnet *ifp = uether_getifp(ue); 2041 MUGE_LOCK_ASSERT(sc, MA_OWNED); 2042 2043 if (lan78xx_setmacaddress(sc, IF_LLADDR(ifp))) 2044 muge_dbg_printf(sc, "setting MAC address failed\n"); 2045 2046 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) != 0) 2047 return; 2048 2049 /* Cancel pending I/O. */ 2050 muge_stop(ue); 2051 2052 /* Reset the ethernet interface. */ 2053 muge_reset(sc); 2054 2055 /* Load the multicast filter. */ 2056 muge_setmulti(ue); 2057 2058 /* TCP/UDP checksum offload engines. */ 2059 muge_sethwcsum(sc); 2060 2061 usbd_xfer_set_stall(sc->sc_xfer[MUGE_BULK_DT_WR]); 2062 2063 /* Indicate we are up and running. */ 2064 ifp->if_drv_flags |= IFF_DRV_RUNNING; 2065 2066 /* Switch to selected media. */ 2067 muge_ifmedia_upd(ifp); 2068 muge_start(ue); 2069 } 2070 2071 /** 2072 * muge_stop - Stops communication with the LAN78xx chip 2073 * @ue: USB ether interface 2074 */ 2075 static void 2076 muge_stop(struct usb_ether *ue) 2077 { 2078 struct muge_softc *sc = uether_getsc(ue); 2079 struct ifnet *ifp = uether_getifp(ue); 2080 2081 MUGE_LOCK_ASSERT(sc, MA_OWNED); 2082 2083 ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE); 2084 sc->sc_flags &= ~MUGE_FLAG_LINK; 2085 2086 /* 2087 * Stop all the transfers, if not already stopped. 2088 */ 2089 usbd_transfer_stop(sc->sc_xfer[MUGE_BULK_DT_WR]); 2090 usbd_transfer_stop(sc->sc_xfer[MUGE_BULK_DT_RD]); 2091 } 2092 2093 /** 2094 * muge_tick - Called periodically to monitor the state of the LAN95xx chip 2095 * @ue: USB ether interface 2096 * 2097 * Simply calls the mii status functions to check the state of the link. 2098 * 2099 * LOCKING: 2100 * Should be called with the MUGE lock held. 2101 */ 2102 static void 2103 muge_tick(struct usb_ether *ue) 2104 { 2105 2106 struct muge_softc *sc = uether_getsc(ue); 2107 struct mii_data *mii = uether_getmii(&sc->sc_ue); 2108 2109 MUGE_LOCK_ASSERT(sc, MA_OWNED); 2110 2111 mii_tick(mii); 2112 if ((sc->sc_flags & MUGE_FLAG_LINK) == 0) { 2113 lan78xx_miibus_statchg(ue->ue_dev); 2114 if ((sc->sc_flags & MUGE_FLAG_LINK) != 0) 2115 muge_start(ue); 2116 } 2117 } 2118 2119 /** 2120 * muge_ifmedia_sts - Report current media status 2121 * @ifp: inet interface pointer 2122 * @ifmr: interface media request 2123 * 2124 * Call the mii functions to get the media status. 2125 * 2126 * LOCKING: 2127 * Internally takes and releases the device lock. 2128 */ 2129 static void 2130 muge_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 2131 { 2132 struct muge_softc *sc = ifp->if_softc; 2133 struct mii_data *mii = uether_getmii(&sc->sc_ue); 2134 2135 MUGE_LOCK(sc); 2136 mii_pollstat(mii); 2137 ifmr->ifm_active = mii->mii_media_active; 2138 ifmr->ifm_status = mii->mii_media_status; 2139 MUGE_UNLOCK(sc); 2140 } 2141 2142 /** 2143 * muge_probe - Probe the interface. 2144 * @dev: muge device handle 2145 * 2146 * Checks if the device is a match for this driver. 2147 * 2148 * RETURNS: 2149 * Returns 0 on success or an error code on failure. 2150 */ 2151 static int 2152 muge_probe(device_t dev) 2153 { 2154 struct usb_attach_arg *uaa = device_get_ivars(dev); 2155 2156 if (uaa->usb_mode != USB_MODE_HOST) 2157 return (ENXIO); 2158 if (uaa->info.bConfigIndex != MUGE_CONFIG_INDEX) 2159 return (ENXIO); 2160 if (uaa->info.bIfaceIndex != MUGE_IFACE_IDX) 2161 return (ENXIO); 2162 return (usbd_lookup_id_by_uaa(lan78xx_devs, sizeof(lan78xx_devs), uaa)); 2163 } 2164 2165 /** 2166 * muge_attach - Attach the interface. 2167 * @dev: muge device handle 2168 * 2169 * Allocate softc structures, do ifmedia setup and ethernet/BPF attach. 2170 * 2171 * RETURNS: 2172 * Returns 0 on success or a negative error code. 2173 */ 2174 static int 2175 muge_attach(device_t dev) 2176 { 2177 struct usb_attach_arg *uaa = device_get_ivars(dev); 2178 struct muge_softc *sc = device_get_softc(dev); 2179 struct usb_ether *ue = &sc->sc_ue; 2180 uint8_t iface_index; 2181 int err; 2182 2183 sc->sc_flags = USB_GET_DRIVER_INFO(uaa); 2184 2185 device_set_usb_desc(dev); 2186 2187 mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF); 2188 2189 /* Setup the endpoints for the Microchip LAN78xx device. */ 2190 iface_index = MUGE_IFACE_IDX; 2191 err = usbd_transfer_setup(uaa->device, &iface_index, sc->sc_xfer, 2192 muge_config, MUGE_N_TRANSFER, sc, &sc->sc_mtx); 2193 if (err) { 2194 device_printf(dev, "error: allocating USB transfers failed\n"); 2195 goto err; 2196 } 2197 2198 ue->ue_sc = sc; 2199 ue->ue_dev = dev; 2200 ue->ue_udev = uaa->device; 2201 ue->ue_mtx = &sc->sc_mtx; 2202 ue->ue_methods = &muge_ue_methods; 2203 2204 err = uether_ifattach(ue); 2205 if (err) { 2206 device_printf(dev, "error: could not attach interface\n"); 2207 goto err_usbd; 2208 } 2209 2210 /* Wait for lan78xx_chip_init from post-attach callback to complete. */ 2211 uether_ifattach_wait(ue); 2212 if (!(sc->sc_flags & MUGE_FLAG_INIT_DONE)) 2213 goto err_attached; 2214 2215 return (0); 2216 2217 err_attached: 2218 uether_ifdetach(ue); 2219 err_usbd: 2220 usbd_transfer_unsetup(sc->sc_xfer, MUGE_N_TRANSFER); 2221 err: 2222 mtx_destroy(&sc->sc_mtx); 2223 return (ENXIO); 2224 } 2225 2226 /** 2227 * muge_detach - Detach the interface. 2228 * @dev: muge device handle 2229 * 2230 * RETURNS: 2231 * Returns 0. 2232 */ 2233 static int 2234 muge_detach(device_t dev) 2235 { 2236 2237 struct muge_softc *sc = device_get_softc(dev); 2238 struct usb_ether *ue = &sc->sc_ue; 2239 2240 usbd_transfer_unsetup(sc->sc_xfer, MUGE_N_TRANSFER); 2241 uether_ifdetach(ue); 2242 mtx_destroy(&sc->sc_mtx); 2243 2244 return (0); 2245 } 2246 2247 static device_method_t muge_methods[] = { 2248 /* Device interface */ 2249 DEVMETHOD(device_probe, muge_probe), 2250 DEVMETHOD(device_attach, muge_attach), 2251 DEVMETHOD(device_detach, muge_detach), 2252 2253 /* Bus interface */ 2254 DEVMETHOD(bus_print_child, bus_generic_print_child), 2255 DEVMETHOD(bus_driver_added, bus_generic_driver_added), 2256 2257 /* MII interface */ 2258 DEVMETHOD(miibus_readreg, lan78xx_miibus_readreg), 2259 DEVMETHOD(miibus_writereg, lan78xx_miibus_writereg), 2260 DEVMETHOD(miibus_statchg, lan78xx_miibus_statchg), 2261 2262 DEVMETHOD_END 2263 }; 2264 2265 static driver_t muge_driver = { 2266 .name = "muge", 2267 .methods = muge_methods, 2268 .size = sizeof(struct muge_softc), 2269 }; 2270 2271 static devclass_t muge_devclass; 2272 2273 DRIVER_MODULE(muge, uhub, muge_driver, muge_devclass, NULL, NULL); 2274 DRIVER_MODULE(miibus, muge, miibus_driver, miibus_devclass, NULL, NULL); 2275 MODULE_DEPEND(muge, uether, 1, 1, 1); 2276 MODULE_DEPEND(muge, usb, 1, 1, 1); 2277 MODULE_DEPEND(muge, ether, 1, 1, 1); 2278 MODULE_DEPEND(muge, miibus, 1, 1, 1); 2279 MODULE_VERSION(muge, 1); 2280 USB_PNP_HOST_INFO(lan78xx_devs); 2281