1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer, 12 * without modification. 13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 14 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any 15 * redistribution must be conditioned upon including a substantially 16 * similar Disclaimer requirement for further binary redistribution. 17 * 18 * NO WARRANTY 19 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 20 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 21 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY 22 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL 23 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, 24 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 25 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 26 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER 27 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 28 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 29 * THE POSSIBILITY OF SUCH DAMAGES. 30 */ 31 32 #include <sys/cdefs.h> 33 __FBSDID("$FreeBSD$"); 34 35 /* 36 * Driver for the Atheros Wireless LAN controller. 37 * 38 * This software is derived from work of Atsushi Onoe; his contribution 39 * is greatly appreciated. 40 */ 41 42 #include "opt_inet.h" 43 #include "opt_ath.h" 44 /* 45 * This is needed for register operations which are performed 46 * by the driver - eg, calls to ath_hal_gettsf32(). 47 * 48 * It's also required for any AH_DEBUG checks in here, eg the 49 * module dependencies. 50 */ 51 #include "opt_ah.h" 52 #include "opt_wlan.h" 53 54 #include <sys/param.h> 55 #include <sys/systm.h> 56 #include <sys/sysctl.h> 57 #include <sys/mbuf.h> 58 #include <sys/malloc.h> 59 #include <sys/lock.h> 60 #include <sys/mutex.h> 61 #include <sys/kernel.h> 62 #include <sys/socket.h> 63 #include <sys/sockio.h> 64 #include <sys/errno.h> 65 #include <sys/callout.h> 66 #include <sys/bus.h> 67 #include <sys/endian.h> 68 #include <sys/kthread.h> 69 #include <sys/taskqueue.h> 70 #include <sys/priv.h> 71 #include <sys/module.h> 72 #include <sys/ktr.h> 73 #include <sys/smp.h> /* for mp_ncpus */ 74 75 #include <machine/bus.h> 76 77 #include <net/if.h> 78 #include <net/if_var.h> 79 #include <net/if_dl.h> 80 #include <net/if_media.h> 81 #include <net/if_types.h> 82 #include <net/if_arp.h> 83 #include <net/ethernet.h> 84 #include <net/if_llc.h> 85 86 #include <net80211/ieee80211_var.h> 87 #include <net80211/ieee80211_regdomain.h> 88 #ifdef IEEE80211_SUPPORT_SUPERG 89 #include <net80211/ieee80211_superg.h> 90 #endif 91 #ifdef IEEE80211_SUPPORT_TDMA 92 #include <net80211/ieee80211_tdma.h> 93 #endif 94 95 #include <net/bpf.h> 96 97 #ifdef INET 98 #include <netinet/in.h> 99 #include <netinet/if_ether.h> 100 #endif 101 102 #include <dev/ath/if_athvar.h> 103 #include <dev/ath/ath_hal/ah_devid.h> /* XXX for softled */ 104 #include <dev/ath/ath_hal/ah_diagcodes.h> 105 106 #include <dev/ath/if_ath_debug.h> 107 #include <dev/ath/if_ath_misc.h> 108 #include <dev/ath/if_ath_tsf.h> 109 #include <dev/ath/if_ath_tx.h> 110 #include <dev/ath/if_ath_sysctl.h> 111 #include <dev/ath/if_ath_led.h> 112 #include <dev/ath/if_ath_keycache.h> 113 #include <dev/ath/if_ath_rx.h> 114 #include <dev/ath/if_ath_beacon.h> 115 #include <dev/ath/if_athdfs.h> 116 117 #ifdef ATH_TX99_DIAG 118 #include <dev/ath/ath_tx99/ath_tx99.h> 119 #endif 120 121 #ifdef ATH_DEBUG_ALQ 122 #include <dev/ath/if_ath_alq.h> 123 #endif 124 125 #ifdef IEEE80211_SUPPORT_TDMA 126 #include <dev/ath/if_ath_tdma.h> 127 128 static void ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt, 129 u_int32_t bintval); 130 static void ath_tdma_bintvalsetup(struct ath_softc *sc, 131 const struct ieee80211_tdma_state *tdma); 132 #endif /* IEEE80211_SUPPORT_TDMA */ 133 134 #ifdef IEEE80211_SUPPORT_TDMA 135 static void 136 ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt, u_int32_t bintval) 137 { 138 struct ath_hal *ah = sc->sc_ah; 139 HAL_BEACON_TIMERS bt; 140 141 bt.bt_intval = bintval | HAL_BEACON_ENA; 142 bt.bt_nexttbtt = nexttbtt; 143 bt.bt_nextdba = (nexttbtt<<3) - sc->sc_tdmadbaprep; 144 bt.bt_nextswba = (nexttbtt<<3) - sc->sc_tdmaswbaprep; 145 bt.bt_nextatim = nexttbtt+1; 146 /* Enables TBTT, DBA, SWBA timers by default */ 147 bt.bt_flags = 0; 148 #if 0 149 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 150 "%s: intval=%d (0x%08x) nexttbtt=%u (0x%08x), nextdba=%u (0x%08x), nextswba=%u (0x%08x),nextatim=%u (0x%08x)\n", 151 __func__, 152 bt.bt_intval, 153 bt.bt_intval, 154 bt.bt_nexttbtt, 155 bt.bt_nexttbtt, 156 bt.bt_nextdba, 157 bt.bt_nextdba, 158 bt.bt_nextswba, 159 bt.bt_nextswba, 160 bt.bt_nextatim, 161 bt.bt_nextatim); 162 #endif 163 164 #ifdef ATH_DEBUG_ALQ 165 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_SET)) { 166 struct if_ath_alq_tdma_timer_set t; 167 t.bt_intval = htobe32(bt.bt_intval); 168 t.bt_nexttbtt = htobe32(bt.bt_nexttbtt); 169 t.bt_nextdba = htobe32(bt.bt_nextdba); 170 t.bt_nextswba = htobe32(bt.bt_nextswba); 171 t.bt_nextatim = htobe32(bt.bt_nextatim); 172 t.bt_flags = htobe32(bt.bt_flags); 173 t.sc_tdmadbaprep = htobe32(sc->sc_tdmadbaprep); 174 t.sc_tdmaswbaprep = htobe32(sc->sc_tdmaswbaprep); 175 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_SET, 176 sizeof(t), (char *) &t); 177 } 178 #endif 179 180 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 181 "%s: nexttbtt=%u (0x%08x), nexttbtt tsf=%lld (0x%08llx)\n", 182 __func__, 183 bt.bt_nexttbtt, 184 bt.bt_nexttbtt, 185 (long long) ( ((u_int64_t) (bt.bt_nexttbtt)) << 10), 186 (long long) ( ((u_int64_t) (bt.bt_nexttbtt)) << 10)); 187 ath_hal_beaconsettimers(ah, &bt); 188 } 189 190 /* 191 * Calculate the beacon interval. This is periodic in the 192 * superframe for the bss. We assume each station is configured 193 * identically wrt transmit rate so the guard time we calculate 194 * above will be the same on all stations. Note we need to 195 * factor in the xmit time because the hardware will schedule 196 * a frame for transmit if the start of the frame is within 197 * the burst time. When we get hardware that properly kills 198 * frames in the PCU we can reduce/eliminate the guard time. 199 * 200 * Roundup to 1024 is so we have 1 TU buffer in the guard time 201 * to deal with the granularity of the nexttbtt timer. 11n MAC's 202 * with 1us timer granularity should allow us to reduce/eliminate 203 * this. 204 */ 205 static void 206 ath_tdma_bintvalsetup(struct ath_softc *sc, 207 const struct ieee80211_tdma_state *tdma) 208 { 209 /* copy from vap state (XXX check all vaps have same value?) */ 210 sc->sc_tdmaslotlen = tdma->tdma_slotlen; 211 212 sc->sc_tdmabintval = roundup((sc->sc_tdmaslotlen+sc->sc_tdmaguard) * 213 tdma->tdma_slotcnt, 1024); 214 sc->sc_tdmabintval >>= 10; /* TSF -> TU */ 215 if (sc->sc_tdmabintval & 1) 216 sc->sc_tdmabintval++; 217 218 if (tdma->tdma_slot == 0) { 219 /* 220 * Only slot 0 beacons; other slots respond. 221 */ 222 sc->sc_imask |= HAL_INT_SWBA; 223 sc->sc_tdmaswba = 0; /* beacon immediately */ 224 } else { 225 /* XXX all vaps must be slot 0 or slot !0 */ 226 sc->sc_imask &= ~HAL_INT_SWBA; 227 } 228 } 229 230 /* 231 * Max 802.11 overhead. This assumes no 4-address frames and 232 * the encapsulation done by ieee80211_encap (llc). We also 233 * include potential crypto overhead. 234 */ 235 #define IEEE80211_MAXOVERHEAD \ 236 (sizeof(struct ieee80211_qosframe) \ 237 + sizeof(struct llc) \ 238 + IEEE80211_ADDR_LEN \ 239 + IEEE80211_WEP_IVLEN \ 240 + IEEE80211_WEP_KIDLEN \ 241 + IEEE80211_WEP_CRCLEN \ 242 + IEEE80211_WEP_MICLEN \ 243 + IEEE80211_CRC_LEN) 244 245 /* 246 * Setup initially for tdma operation. Start the beacon 247 * timers and enable SWBA if we are slot 0. Otherwise 248 * we wait for slot 0 to arrive so we can sync up before 249 * starting to transmit. 250 */ 251 void 252 ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap) 253 { 254 struct ath_hal *ah = sc->sc_ah; 255 struct ieee80211com *ic = &sc->sc_ic; 256 const struct ieee80211_txparam *tp; 257 const struct ieee80211_tdma_state *tdma = NULL; 258 int rix; 259 260 if (vap == NULL) { 261 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */ 262 if (vap == NULL) { 263 device_printf(sc->sc_dev, "%s: no vaps?\n", __func__); 264 return; 265 } 266 } 267 /* XXX should take a locked ref to iv_bss */ 268 tp = vap->iv_bss->ni_txparms; 269 /* 270 * Calculate the guard time for each slot. This is the 271 * time to send a maximal-size frame according to the 272 * fixed/lowest transmit rate. Note that the interface 273 * mtu does not include the 802.11 overhead so we must 274 * tack that on (ath_hal_computetxtime includes the 275 * preamble and plcp in its calculation). 276 */ 277 tdma = vap->iv_tdma; 278 if (tp->ucastrate != IEEE80211_FIXED_RATE_NONE) 279 rix = ath_tx_findrix(sc, tp->ucastrate); 280 else 281 rix = ath_tx_findrix(sc, tp->mcastrate); 282 283 /* 284 * If the chip supports enforcing TxOP on transmission, 285 * we can just delete the guard window. It isn't at all required. 286 */ 287 if (sc->sc_hasenforcetxop) { 288 sc->sc_tdmaguard = 0; 289 } else { 290 /* XXX short preamble assumed */ 291 /* XXX non-11n rate assumed */ 292 sc->sc_tdmaguard = ath_hal_computetxtime(ah, sc->sc_currates, 293 if_getmtu(vap->iv_ifp) + IEEE80211_MAXOVERHEAD, rix, AH_TRUE, 294 AH_TRUE); 295 } 296 297 ath_hal_intrset(ah, 0); 298 299 ath_beaconq_config(sc); /* setup h/w beacon q */ 300 if (sc->sc_setcca) 301 ath_hal_setcca(ah, AH_FALSE); /* disable CCA */ 302 ath_tdma_bintvalsetup(sc, tdma); /* calculate beacon interval */ 303 ath_tdma_settimers(sc, sc->sc_tdmabintval, 304 sc->sc_tdmabintval | HAL_BEACON_RESET_TSF); 305 sc->sc_syncbeacon = 0; 306 307 sc->sc_avgtsfdeltap = TDMA_DUMMY_MARKER; 308 sc->sc_avgtsfdeltam = TDMA_DUMMY_MARKER; 309 310 ath_hal_intrset(ah, sc->sc_imask); 311 312 DPRINTF(sc, ATH_DEBUG_TDMA, "%s: slot %u len %uus cnt %u " 313 "bsched %u guard %uus bintval %u TU dba prep %u\n", __func__, 314 tdma->tdma_slot, tdma->tdma_slotlen, tdma->tdma_slotcnt, 315 tdma->tdma_bintval, sc->sc_tdmaguard, sc->sc_tdmabintval, 316 sc->sc_tdmadbaprep); 317 318 #ifdef ATH_DEBUG_ALQ 319 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_CONFIG)) { 320 struct if_ath_alq_tdma_timer_config t; 321 322 t.tdma_slot = htobe32(tdma->tdma_slot); 323 t.tdma_slotlen = htobe32(tdma->tdma_slotlen); 324 t.tdma_slotcnt = htobe32(tdma->tdma_slotcnt); 325 t.tdma_bintval = htobe32(tdma->tdma_bintval); 326 t.tdma_guard = htobe32(sc->sc_tdmaguard); 327 t.tdma_scbintval = htobe32(sc->sc_tdmabintval); 328 t.tdma_dbaprep = htobe32(sc->sc_tdmadbaprep); 329 330 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_CONFIG, 331 sizeof(t), (char *) &t); 332 } 333 #endif /* ATH_DEBUG_ALQ */ 334 } 335 336 /* 337 * Update tdma operation. Called from the 802.11 layer 338 * when a beacon is received from the TDMA station operating 339 * in the slot immediately preceding us in the bss. Use 340 * the rx timestamp for the beacon frame to update our 341 * beacon timers so we follow their schedule. Note that 342 * by using the rx timestamp we implicitly include the 343 * propagation delay in our schedule. 344 * 345 * XXX TODO: since the changes for the AR5416 and later chips 346 * involved changing the TSF/TU calculations, we need to make 347 * sure that various calculations wrap consistently. 348 * 349 * A lot of the problems stemmed from the calculations wrapping 350 * at 65,535 TU. Since a lot of the math is still being done in 351 * TU, please audit it to ensure that when the TU values programmed 352 * into the timers wrap at (2^31)-1 TSF, all the various terms 353 * wrap consistently. 354 */ 355 void 356 ath_tdma_update(struct ieee80211_node *ni, 357 const struct ieee80211_tdma_param *tdma, int changed) 358 { 359 #define TSF_TO_TU(_h,_l) \ 360 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10)) 361 #define TU_TO_TSF(_tu) (((u_int64_t)(_tu)) << 10) 362 struct ieee80211vap *vap = ni->ni_vap; 363 struct ieee80211com *ic = ni->ni_ic; 364 struct ath_softc *sc = ic->ic_softc; 365 struct ath_hal *ah = sc->sc_ah; 366 const HAL_RATE_TABLE *rt = sc->sc_currates; 367 u_int64_t tsf, rstamp, nextslot, nexttbtt, nexttbtt_full; 368 u_int32_t txtime, nextslottu; 369 int32_t tudelta, tsfdelta; 370 const struct ath_rx_status *rs; 371 int rix; 372 373 sc->sc_stats.ast_tdma_update++; 374 375 /* 376 * Check for and adopt configuration changes. 377 */ 378 if (changed != 0) { 379 const struct ieee80211_tdma_state *ts = vap->iv_tdma; 380 381 ath_tdma_bintvalsetup(sc, ts); 382 if (changed & TDMA_UPDATE_SLOTLEN) 383 ath_wme_update(ic); 384 385 DPRINTF(sc, ATH_DEBUG_TDMA, 386 "%s: adopt slot %u slotcnt %u slotlen %u us " 387 "bintval %u TU\n", __func__, 388 ts->tdma_slot, ts->tdma_slotcnt, ts->tdma_slotlen, 389 sc->sc_tdmabintval); 390 391 /* XXX right? */ 392 ath_hal_intrset(ah, sc->sc_imask); 393 /* NB: beacon timers programmed below */ 394 } 395 396 /* extend rx timestamp to 64 bits */ 397 rs = sc->sc_lastrs; 398 tsf = ath_hal_gettsf64(ah); 399 rstamp = ath_extend_tsf(sc, rs->rs_tstamp, tsf); 400 /* 401 * The rx timestamp is set by the hardware on completing 402 * reception (at the point where the rx descriptor is DMA'd 403 * to the host). To find the start of our next slot we 404 * must adjust this time by the time required to send 405 * the packet just received. 406 */ 407 rix = rt->rateCodeToIndex[rs->rs_rate]; 408 409 /* 410 * To calculate the packet duration for legacy rates, we 411 * only need the rix and preamble. 412 * 413 * For 11n non-aggregate frames, we also need the channel 414 * width and short/long guard interval. 415 * 416 * For 11n aggregate frames, the required hacks are a little 417 * more subtle. You need to figure out the frame duration 418 * for each frame, including the delimiters. However, when 419 * a frame isn't received successfully, we won't hear it 420 * (unless you enable reception of CRC errored frames), so 421 * your duration calculation is going to be off. 422 * 423 * However, we can assume that the beacon frames won't be 424 * transmitted as aggregate frames, so we should be okay. 425 * Just add a check to ensure that we aren't handed something 426 * bad. 427 * 428 * For ath_hal_pkt_txtime() - for 11n rates, shortPreamble is 429 * actually short guard interval. For legacy rates, 430 * it's short preamble. 431 */ 432 txtime = ath_hal_pkt_txtime(ah, rt, rs->rs_datalen, 433 rix, 434 !! (rs->rs_flags & HAL_RX_2040), 435 (rix & 0x80) ? 436 (! (rs->rs_flags & HAL_RX_GI)) : rt->info[rix].shortPreamble, 437 AH_TRUE); 438 /* NB: << 9 is to cvt to TU and /2 */ 439 nextslot = (rstamp - txtime) + (sc->sc_tdmabintval << 9); 440 441 /* 442 * For 802.11n chips: nextslottu needs to be the full TSF space, 443 * not just 0..65535 TU. 444 */ 445 nextslottu = TSF_TO_TU(nextslot>>32, nextslot); 446 /* 447 * Retrieve the hardware NextTBTT in usecs 448 * and calculate the difference between what the 449 * other station thinks and what we have programmed. This 450 * lets us figure how to adjust our timers to match. The 451 * adjustments are done by pulling the TSF forward and possibly 452 * rewriting the beacon timers. 453 */ 454 /* 455 * The logic here assumes the nexttbtt counter is in TSF 456 * but the prr-11n NICs are in TU. The HAL shifts them 457 * to TSF but there's two important differences: 458 * 459 * + The TU->TSF values have 0's for the low 9 bits, and 460 * + The counter wraps at TU_TO_TSF(HAL_BEACON_PERIOD + 1) for 461 * the pre-11n NICs, but not for the 11n NICs. 462 * 463 * So for now, just make sure the nexttbtt value we get 464 * matches the second issue or once nexttbtt exceeds this 465 * value, tsfdelta ends up becoming very negative and all 466 * of the adjustments get very messed up. 467 */ 468 469 /* 470 * We need to track the full nexttbtt rather than having it 471 * truncated at HAL_BEACON_PERIOD, as programming the 472 * nexttbtt (and related) registers for the 11n chips is 473 * actually going to take the full 32 bit space, rather than 474 * just 0..65535 TU. 475 */ 476 nexttbtt_full = ath_hal_getnexttbtt(ah); 477 nexttbtt = nexttbtt_full % (TU_TO_TSF(HAL_BEACON_PERIOD + 1)); 478 tsfdelta = (int32_t)((nextslot % TU_TO_TSF(HAL_BEACON_PERIOD + 1)) - nexttbtt); 479 480 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 481 "rs->rstamp %llu rstamp %llu tsf %llu txtime %d, nextslot %llu, " 482 "nextslottu %d, nextslottume %d\n", 483 (unsigned long long) rs->rs_tstamp, 484 (unsigned long long) rstamp, 485 (unsigned long long) tsf, txtime, 486 (unsigned long long) nextslot, 487 nextslottu, TSF_TO_TU(nextslot >> 32, nextslot)); 488 DPRINTF(sc, ATH_DEBUG_TDMA, 489 " beacon tstamp: %llu (0x%016llx)\n", 490 (unsigned long long) le64toh(ni->ni_tstamp.tsf), 491 (unsigned long long) le64toh(ni->ni_tstamp.tsf)); 492 493 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 494 "nexttbtt %llu (0x%08llx) tsfdelta %d avg +%d/-%d\n", 495 (unsigned long long) nexttbtt, 496 (long long) nexttbtt, 497 tsfdelta, 498 TDMA_AVG(sc->sc_avgtsfdeltap), TDMA_AVG(sc->sc_avgtsfdeltam)); 499 500 if (tsfdelta < 0) { 501 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0); 502 TDMA_SAMPLE(sc->sc_avgtsfdeltam, -tsfdelta); 503 tsfdelta = -tsfdelta % 1024; 504 nextslottu++; 505 } else if (tsfdelta > 0) { 506 TDMA_SAMPLE(sc->sc_avgtsfdeltap, tsfdelta); 507 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0); 508 tsfdelta = 1024 - (tsfdelta % 1024); 509 nextslottu++; 510 } else { 511 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0); 512 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0); 513 } 514 tudelta = nextslottu - TSF_TO_TU(nexttbtt_full >> 32, nexttbtt_full); 515 516 #ifdef ATH_DEBUG_ALQ 517 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_BEACON_STATE)) { 518 struct if_ath_alq_tdma_beacon_state t; 519 t.rx_tsf = htobe64(rstamp); 520 t.beacon_tsf = htobe64(le64toh(ni->ni_tstamp.tsf)); 521 t.tsf64 = htobe64(tsf); 522 t.nextslot_tsf = htobe64(nextslot); 523 t.nextslot_tu = htobe32(nextslottu); 524 t.txtime = htobe32(txtime); 525 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_BEACON_STATE, 526 sizeof(t), (char *) &t); 527 } 528 529 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_SLOT_CALC)) { 530 struct if_ath_alq_tdma_slot_calc t; 531 532 t.nexttbtt = htobe64(nexttbtt_full); 533 t.next_slot = htobe64(nextslot); 534 t.tsfdelta = htobe32(tsfdelta); 535 t.avg_plus = htobe32(TDMA_AVG(sc->sc_avgtsfdeltap)); 536 t.avg_minus = htobe32(TDMA_AVG(sc->sc_avgtsfdeltam)); 537 538 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_SLOT_CALC, 539 sizeof(t), (char *) &t); 540 } 541 #endif 542 543 /* 544 * Copy sender's timetstamp into tdma ie so they can 545 * calculate roundtrip time. We submit a beacon frame 546 * below after any timer adjustment. The frame goes out 547 * at the next TBTT so the sender can calculate the 548 * roundtrip by inspecting the tdma ie in our beacon frame. 549 * 550 * NB: This tstamp is subtlely preserved when 551 * IEEE80211_BEACON_TDMA is marked (e.g. when the 552 * slot position changes) because ieee80211_add_tdma 553 * skips over the data. 554 */ 555 memcpy(vap->iv_bcn_off.bo_tdma + 556 __offsetof(struct ieee80211_tdma_param, tdma_tstamp), 557 &ni->ni_tstamp.data, 8); 558 #if 0 559 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 560 "tsf %llu nextslot %llu (%d, %d) nextslottu %u nexttbtt %llu (%d)\n", 561 (unsigned long long) tsf, (unsigned long long) nextslot, 562 (int)(nextslot - tsf), tsfdelta, nextslottu, nexttbtt, tudelta); 563 #endif 564 /* 565 * Adjust the beacon timers only when pulling them forward 566 * or when going back by less than the beacon interval. 567 * Negative jumps larger than the beacon interval seem to 568 * cause the timers to stop and generally cause instability. 569 * This basically filters out jumps due to missed beacons. 570 */ 571 if (tudelta != 0 && (tudelta > 0 || -tudelta < sc->sc_tdmabintval)) { 572 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 573 "%s: calling ath_tdma_settimers; nextslottu=%d, bintval=%d\n", 574 __func__, 575 nextslottu, 576 sc->sc_tdmabintval); 577 ath_tdma_settimers(sc, nextslottu, sc->sc_tdmabintval); 578 sc->sc_stats.ast_tdma_timers++; 579 } 580 if (tsfdelta > 0) { 581 uint64_t tsf; 582 583 /* XXX should just teach ath_hal_adjusttsf() to do this */ 584 tsf = ath_hal_gettsf64(ah); 585 ath_hal_settsf64(ah, tsf + tsfdelta); 586 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER, 587 "%s: calling ath_hal_adjusttsf: TSF=%llu, tsfdelta=%d\n", 588 __func__, 589 (unsigned long long) tsf, 590 tsfdelta); 591 592 #ifdef ATH_DEBUG_ALQ 593 if (if_ath_alq_checkdebug(&sc->sc_alq, 594 ATH_ALQ_TDMA_TSF_ADJUST)) { 595 struct if_ath_alq_tdma_tsf_adjust t; 596 597 t.tsfdelta = htobe32(tsfdelta); 598 t.tsf64_old = htobe64(tsf); 599 t.tsf64_new = htobe64(tsf + tsfdelta); 600 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TSF_ADJUST, 601 sizeof(t), (char *) &t); 602 } 603 #endif /* ATH_DEBUG_ALQ */ 604 sc->sc_stats.ast_tdma_tsf++; 605 } 606 ath_tdma_beacon_send(sc, vap); /* prepare response */ 607 #undef TU_TO_TSF 608 #undef TSF_TO_TU 609 } 610 611 /* 612 * Transmit a beacon frame at SWBA. Dynamic updates 613 * to the frame contents are done as needed. 614 */ 615 void 616 ath_tdma_beacon_send(struct ath_softc *sc, struct ieee80211vap *vap) 617 { 618 struct ath_hal *ah = sc->sc_ah; 619 struct ath_buf *bf; 620 int otherant; 621 622 /* 623 * Check if the previous beacon has gone out. If 624 * not don't try to post another, skip this period 625 * and wait for the next. Missed beacons indicate 626 * a problem and should not occur. If we miss too 627 * many consecutive beacons reset the device. 628 */ 629 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) { 630 sc->sc_bmisscount++; 631 DPRINTF(sc, ATH_DEBUG_BEACON, 632 "%s: missed %u consecutive beacons\n", 633 __func__, sc->sc_bmisscount); 634 if (sc->sc_bmisscount >= ath_bstuck_threshold) 635 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask); 636 return; 637 } 638 if (sc->sc_bmisscount != 0) { 639 DPRINTF(sc, ATH_DEBUG_BEACON, 640 "%s: resume beacon xmit after %u misses\n", 641 __func__, sc->sc_bmisscount); 642 sc->sc_bmisscount = 0; 643 } 644 645 /* 646 * Check recent per-antenna transmit statistics and flip 647 * the default antenna if noticeably more frames went out 648 * on the non-default antenna. 649 * XXX assumes 2 anntenae 650 */ 651 if (!sc->sc_diversity) { 652 otherant = sc->sc_defant & 1 ? 2 : 1; 653 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2) 654 ath_setdefantenna(sc, otherant); 655 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0; 656 } 657 658 bf = ath_beacon_generate(sc, vap); 659 /* XXX We don't do cabq traffic, but just for completeness .. */ 660 ATH_TXQ_LOCK(sc->sc_cabq); 661 ath_beacon_cabq_start(sc); 662 ATH_TXQ_UNLOCK(sc->sc_cabq); 663 664 if (bf != NULL) { 665 /* 666 * Stop any current dma and put the new frame on the queue. 667 * This should never fail since we check above that no frames 668 * are still pending on the queue. 669 */ 670 if ((! sc->sc_isedma) && 671 (! ath_hal_stoptxdma(ah, sc->sc_bhalq))) { 672 DPRINTF(sc, ATH_DEBUG_ANY, 673 "%s: beacon queue %u did not stop?\n", 674 __func__, sc->sc_bhalq); 675 /* NB: the HAL still stops DMA, so proceed */ 676 } 677 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr); 678 ath_hal_txstart(ah, sc->sc_bhalq); 679 680 sc->sc_stats.ast_be_xmit++; /* XXX per-vap? */ 681 682 /* 683 * Record local TSF for our last send for use 684 * in arbitrating slot collisions. 685 */ 686 /* XXX should take a locked ref to iv_bss */ 687 vap->iv_bss->ni_tstamp.tsf = ath_hal_gettsf64(ah); 688 } 689 } 690 #endif /* IEEE80211_SUPPORT_TDMA */ 691