1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Device Tree Source for common parts of Salvator-X board variants 4 * 5 * Copyright (C) 2015-2016 Renesas Electronics Corp. 6 */ 7 8/* 9 * SSI-AK4613 10 * 11 * This command is required when Playback/Capture 12 * 13 * amixer set "DVC Out" 100% 14 * amixer set "DVC In" 100% 15 * 16 * You can use Mute 17 * 18 * amixer set "DVC Out Mute" on 19 * amixer set "DVC In Mute" on 20 * 21 * You can use Volume Ramp 22 * 23 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 24 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 25 * amixer set "DVC Out Ramp" on 26 * aplay xxx.wav & 27 * amixer set "DVC Out" 80% // Volume Down 28 * amixer set "DVC Out" 100% // Volume Up 29 */ 30 31#include <dt-bindings/gpio/gpio.h> 32#include <dt-bindings/input/input.h> 33 34/ { 35 aliases { 36 serial0 = &scif2; 37 serial1 = &hscif1; 38 ethernet0 = &avb; 39 mmc0 = &sdhi2; 40 mmc1 = &sdhi0; 41 mmc2 = &sdhi3; 42 }; 43 44 chosen { 45 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; 46 stdout-path = "serial0:115200n8"; 47 }; 48 49 audio_clkout: audio-clkout { 50 /* 51 * This is same as <&rcar_sound 0> 52 * but needed to avoid cs2000/rcar_sound probe dead-lock 53 */ 54 compatible = "fixed-clock"; 55 #clock-cells = <0>; 56 clock-frequency = <12288000>; 57 }; 58 59 backlight: backlight { 60 compatible = "pwm-backlight"; 61 pwms = <&pwm1 0 50000>; 62 63 brightness-levels = <256 128 64 16 8 4 0>; 64 default-brightness-level = <6>; 65 66 power-supply = <®_12v>; 67 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; 68 }; 69 70 cvbs-in { 71 compatible = "composite-video-connector"; 72 label = "CVBS IN"; 73 74 port { 75 cvbs_con: endpoint { 76 remote-endpoint = <&adv7482_ain7>; 77 }; 78 }; 79 }; 80 81 hdmi-in { 82 compatible = "hdmi-connector"; 83 label = "HDMI IN"; 84 type = "a"; 85 86 port { 87 hdmi_in_con: endpoint { 88 remote-endpoint = <&adv7482_hdmi>; 89 }; 90 }; 91 }; 92 93 hdmi0-out { 94 compatible = "hdmi-connector"; 95 label = "HDMI0 OUT"; 96 type = "a"; 97 98 port { 99 hdmi0_con: endpoint { 100 remote-endpoint = <&rcar_dw_hdmi0_out>; 101 }; 102 }; 103 }; 104 105 hdmi1-out { 106 compatible = "hdmi-connector"; 107 label = "HDMI1 OUT"; 108 type = "a"; 109 110 port { 111 hdmi1_con: endpoint { 112 }; 113 }; 114 }; 115 116 keys { 117 compatible = "gpio-keys"; 118 119 pinctrl-0 = <&keys_pins>; 120 pinctrl-names = "default"; 121 122 key-1 { 123 gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; 124 linux,code = <KEY_1>; 125 label = "SW4-1"; 126 wakeup-source; 127 debounce-interval = <20>; 128 }; 129 key-2 { 130 gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; 131 linux,code = <KEY_2>; 132 label = "SW4-2"; 133 wakeup-source; 134 debounce-interval = <20>; 135 }; 136 key-3 { 137 gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; 138 linux,code = <KEY_3>; 139 label = "SW4-3"; 140 wakeup-source; 141 debounce-interval = <20>; 142 }; 143 key-4 { 144 gpios = <&gpio5 23 GPIO_ACTIVE_LOW>; 145 linux,code = <KEY_4>; 146 label = "SW4-4"; 147 wakeup-source; 148 debounce-interval = <20>; 149 }; 150 key-a { 151 gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; 152 linux,code = <KEY_A>; 153 label = "TSW0"; 154 wakeup-source; 155 debounce-interval = <20>; 156 }; 157 key-b { 158 gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; 159 linux,code = <KEY_B>; 160 label = "TSW1"; 161 wakeup-source; 162 debounce-interval = <20>; 163 }; 164 key-c { 165 gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; 166 linux,code = <KEY_C>; 167 label = "TSW2"; 168 wakeup-source; 169 debounce-interval = <20>; 170 }; 171 }; 172 173 reg_1p8v: regulator0 { 174 compatible = "regulator-fixed"; 175 regulator-name = "fixed-1.8V"; 176 regulator-min-microvolt = <1800000>; 177 regulator-max-microvolt = <1800000>; 178 regulator-boot-on; 179 regulator-always-on; 180 }; 181 182 reg_3p3v: regulator1 { 183 compatible = "regulator-fixed"; 184 regulator-name = "fixed-3.3V"; 185 regulator-min-microvolt = <3300000>; 186 regulator-max-microvolt = <3300000>; 187 regulator-boot-on; 188 regulator-always-on; 189 }; 190 191 reg_12v: regulator2 { 192 compatible = "regulator-fixed"; 193 regulator-name = "fixed-12V"; 194 regulator-min-microvolt = <12000000>; 195 regulator-max-microvolt = <12000000>; 196 regulator-boot-on; 197 regulator-always-on; 198 }; 199 200 sound_card: sound { 201 compatible = "audio-graph-card"; 202 203 label = "rcar-sound"; 204 205 dais = <&rsnd_port0 /* ak4613 */ 206 &rsnd_port1 /* HDMI0 */ 207#ifdef SOC_HAS_HDMI1 208 &rsnd_port2 /* HDMI1 */ 209#endif 210 >; 211 }; 212 213 vbus0_usb2: regulator-vbus0-usb2 { 214 compatible = "regulator-fixed"; 215 216 regulator-name = "USB20_VBUS0"; 217 regulator-min-microvolt = <5000000>; 218 regulator-max-microvolt = <5000000>; 219 220 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>; 221 enable-active-high; 222 }; 223 224 vcc_sdhi0: regulator-vcc-sdhi0 { 225 compatible = "regulator-fixed"; 226 227 regulator-name = "SDHI0 Vcc"; 228 regulator-min-microvolt = <3300000>; 229 regulator-max-microvolt = <3300000>; 230 231 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; 232 enable-active-high; 233 }; 234 235 vccq_sdhi0: regulator-vccq-sdhi0 { 236 compatible = "regulator-gpio"; 237 238 regulator-name = "SDHI0 VccQ"; 239 regulator-min-microvolt = <1800000>; 240 regulator-max-microvolt = <3300000>; 241 242 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; 243 gpios-states = <1>; 244 states = <3300000 1>, <1800000 0>; 245 }; 246 247 vcc_sdhi3: regulator-vcc-sdhi3 { 248 compatible = "regulator-fixed"; 249 250 regulator-name = "SDHI3 Vcc"; 251 regulator-min-microvolt = <3300000>; 252 regulator-max-microvolt = <3300000>; 253 254 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; 255 enable-active-high; 256 }; 257 258 vccq_sdhi3: regulator-vccq-sdhi3 { 259 compatible = "regulator-gpio"; 260 261 regulator-name = "SDHI3 VccQ"; 262 regulator-min-microvolt = <1800000>; 263 regulator-max-microvolt = <3300000>; 264 265 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; 266 gpios-states = <1>; 267 states = <3300000 1>, <1800000 0>; 268 }; 269 270 vga { 271 compatible = "vga-connector"; 272 273 port { 274 vga_in: endpoint { 275 remote-endpoint = <&adv7123_out>; 276 }; 277 }; 278 }; 279 280 vga-encoder { 281 compatible = "adi,adv7123"; 282 283 ports { 284 #address-cells = <1>; 285 #size-cells = <0>; 286 287 port@0 { 288 reg = <0>; 289 adv7123_in: endpoint { 290 remote-endpoint = <&du_out_rgb>; 291 }; 292 }; 293 port@1 { 294 reg = <1>; 295 adv7123_out: endpoint { 296 remote-endpoint = <&vga_in>; 297 }; 298 }; 299 }; 300 }; 301 302 x12_clk: x12 { 303 compatible = "fixed-clock"; 304 #clock-cells = <0>; 305 clock-frequency = <24576000>; 306 }; 307 308 /* External DU dot clocks */ 309 x21_clk: x21-clock { 310 compatible = "fixed-clock"; 311 #clock-cells = <0>; 312 clock-frequency = <33000000>; 313 }; 314 315 x22_clk: x22-clock { 316 compatible = "fixed-clock"; 317 #clock-cells = <0>; 318 clock-frequency = <33000000>; 319 }; 320 321 x23_clk: x23-clock { 322 compatible = "fixed-clock"; 323 #clock-cells = <0>; 324 clock-frequency = <25000000>; 325 }; 326}; 327 328&a57_0 { 329 cpu-supply = <&dvfs>; 330}; 331 332&audio_clk_a { 333 clock-frequency = <22579200>; 334}; 335 336&avb { 337 pinctrl-0 = <&avb_pins>; 338 pinctrl-names = "default"; 339 phy-handle = <&phy0>; 340 tx-internal-delay-ps = <2000>; 341 status = "okay"; 342 343 phy0: ethernet-phy@0 { 344 compatible = "ethernet-phy-id0022.1622", 345 "ethernet-phy-ieee802.3-c22"; 346 rxc-skew-ps = <1500>; 347 reg = <0>; 348 interrupt-parent = <&gpio2>; 349 interrupts = <11 IRQ_TYPE_LEVEL_LOW>; 350 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; 351 }; 352}; 353 354&csi20 { 355 status = "okay"; 356 357 ports { 358 port@0 { 359 csi20_in: endpoint { 360 clock-lanes = <0>; 361 data-lanes = <1>; 362 remote-endpoint = <&adv7482_txb>; 363 }; 364 }; 365 }; 366}; 367 368&csi40 { 369 status = "okay"; 370 371 ports { 372 port@0 { 373 csi40_in: endpoint { 374 clock-lanes = <0>; 375 data-lanes = <1 2 3 4>; 376 remote-endpoint = <&adv7482_txa>; 377 }; 378 }; 379 }; 380}; 381 382&du { 383 pinctrl-0 = <&du_pins>; 384 pinctrl-names = "default"; 385 status = "okay"; 386 387 ports { 388 port@0 { 389 endpoint { 390 remote-endpoint = <&adv7123_in>; 391 }; 392 }; 393 }; 394}; 395 396&ehci0 { 397 dr_mode = "otg"; 398 status = "okay"; 399}; 400 401&ehci1 { 402 status = "okay"; 403}; 404 405&extalr_clk { 406 clock-frequency = <32768>; 407}; 408 409&hdmi0 { 410 status = "okay"; 411 412 ports { 413 port@1 { 414 reg = <1>; 415 rcar_dw_hdmi0_out: endpoint { 416 remote-endpoint = <&hdmi0_con>; 417 }; 418 }; 419 port@2 { 420 reg = <2>; 421 dw_hdmi0_snd_in: endpoint { 422 remote-endpoint = <&rsnd_endpoint1>; 423 }; 424 }; 425 }; 426}; 427 428#ifdef SOC_HAS_HDMI1 429&hdmi1 { 430 status = "okay"; 431 432 ports { 433 port@1 { 434 reg = <1>; 435 rcar_dw_hdmi1_out: endpoint { 436 remote-endpoint = <&hdmi1_con>; 437 }; 438 }; 439 port@2 { 440 reg = <2>; 441 dw_hdmi1_snd_in: endpoint { 442 remote-endpoint = <&rsnd_endpoint2>; 443 }; 444 }; 445 }; 446}; 447 448&hdmi1_con { 449 remote-endpoint = <&rcar_dw_hdmi1_out>; 450}; 451#endif /* SOC_HAS_HDMI1 */ 452 453&hscif1 { 454 pinctrl-0 = <&hscif1_pins>; 455 pinctrl-names = "default"; 456 457 uart-has-rtscts; 458 /* Please only enable hscif1 or scif1 */ 459 status = "okay"; 460}; 461 462&hsusb { 463 dr_mode = "otg"; 464 status = "okay"; 465}; 466 467&i2c2 { 468 pinctrl-0 = <&i2c2_pins>; 469 pinctrl-names = "default"; 470 471 status = "okay"; 472 473 clock-frequency = <100000>; 474 475 ak4613: codec@10 { 476 compatible = "asahi-kasei,ak4613"; 477 #sound-dai-cells = <0>; 478 reg = <0x10>; 479 clocks = <&rcar_sound 3>; 480 481 asahi-kasei,in1-single-end; 482 asahi-kasei,in2-single-end; 483 asahi-kasei,out1-single-end; 484 asahi-kasei,out2-single-end; 485 asahi-kasei,out3-single-end; 486 asahi-kasei,out4-single-end; 487 asahi-kasei,out5-single-end; 488 asahi-kasei,out6-single-end; 489 490 port { 491 ak4613_endpoint: endpoint { 492 remote-endpoint = <&rsnd_endpoint0>; 493 }; 494 }; 495 }; 496 497 cs2000: clk_multiplier@4f { 498 #clock-cells = <0>; 499 compatible = "cirrus,cs2000-cp"; 500 reg = <0x4f>; 501 clocks = <&audio_clkout>, <&x12_clk>; 502 clock-names = "clk_in", "ref_clk"; 503 504 assigned-clocks = <&cs2000>; 505 assigned-clock-rates = <24576000>; /* 1/1 divide */ 506 }; 507}; 508 509&i2c4 { 510 status = "okay"; 511 512 pca9654: gpio@20 { 513 compatible = "onnn,pca9654"; 514 reg = <0x20>; 515 gpio-controller; 516 #gpio-cells = <2>; 517 }; 518 519 video-receiver@70 { 520 compatible = "adi,adv7482"; 521 reg = <0x70 0x71 0x72 0x73 0x74 0x75 522 0x60 0x61 0x62 0x63 0x64 0x65>; 523 reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", 524 "infoframe", "cbus", "cec", "sdp", "txa", "txb" ; 525 526 interrupt-parent = <&gpio6>; 527 interrupt-names = "intrq1", "intrq2"; 528 interrupts = <30 IRQ_TYPE_LEVEL_LOW>, 529 <31 IRQ_TYPE_LEVEL_LOW>; 530 531 ports { 532 #address-cells = <1>; 533 #size-cells = <0>; 534 535 port@7 { 536 reg = <7>; 537 538 adv7482_ain7: endpoint { 539 remote-endpoint = <&cvbs_con>; 540 }; 541 }; 542 543 port@8 { 544 reg = <8>; 545 546 adv7482_hdmi: endpoint { 547 remote-endpoint = <&hdmi_in_con>; 548 }; 549 }; 550 551 port@a { 552 reg = <10>; 553 554 adv7482_txa: endpoint { 555 clock-lanes = <0>; 556 data-lanes = <1 2 3 4>; 557 remote-endpoint = <&csi40_in>; 558 }; 559 }; 560 561 port@b { 562 reg = <11>; 563 564 adv7482_txb: endpoint { 565 clock-lanes = <0>; 566 data-lanes = <1>; 567 remote-endpoint = <&csi20_in>; 568 }; 569 }; 570 }; 571 }; 572 573 csa_vdd: adc@7c { 574 compatible = "maxim,max9611"; 575 reg = <0x7c>; 576 577 shunt-resistor-micro-ohms = <5000>; 578 }; 579 580 csa_dvfs: adc@7f { 581 compatible = "maxim,max9611"; 582 reg = <0x7f>; 583 584 shunt-resistor-micro-ohms = <5000>; 585 }; 586}; 587 588&i2c_dvfs { 589 status = "okay"; 590 591 clock-frequency = <400000>; 592 593 pmic: pmic@30 { 594 pinctrl-0 = <&irq0_pins>; 595 pinctrl-names = "default"; 596 597 compatible = "rohm,bd9571mwv"; 598 reg = <0x30>; 599 interrupt-parent = <&intc_ex>; 600 interrupts = <0 IRQ_TYPE_LEVEL_LOW>; 601 interrupt-controller; 602 #interrupt-cells = <2>; 603 gpio-controller; 604 #gpio-cells = <2>; 605 rohm,ddr-backup-power = <0xf>; 606 rohm,rstbmode-level; 607 608 regulators { 609 dvfs: dvfs { 610 regulator-name = "dvfs"; 611 regulator-min-microvolt = <750000>; 612 regulator-max-microvolt = <1030000>; 613 regulator-boot-on; 614 regulator-always-on; 615 }; 616 }; 617 }; 618 619 eeprom@50 { 620 compatible = "rohm,br24t01", "atmel,24c01"; 621 reg = <0x50>; 622 pagesize = <8>; 623 }; 624}; 625 626&ohci0 { 627 dr_mode = "otg"; 628 status = "okay"; 629}; 630 631&ohci1 { 632 status = "okay"; 633}; 634 635&pcie_bus_clk { 636 clock-frequency = <100000000>; 637}; 638 639&pciec0 { 640 status = "okay"; 641}; 642 643&pciec1 { 644 status = "okay"; 645}; 646 647&pfc { 648 pinctrl-0 = <&scif_clk_pins>; 649 pinctrl-names = "default"; 650 651 avb_pins: avb { 652 mux { 653 groups = "avb_link", "avb_mdio", "avb_mii"; 654 function = "avb"; 655 }; 656 657 pins_mdio { 658 groups = "avb_mdio"; 659 drive-strength = <24>; 660 }; 661 662 pins_mii_tx { 663 pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0", 664 "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3"; 665 drive-strength = <12>; 666 }; 667 }; 668 669 du_pins: du { 670 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0"; 671 function = "du"; 672 }; 673 674 hscif1_pins: hscif1 { 675 groups = "hscif1_data_a", "hscif1_ctrl_a"; 676 function = "hscif1"; 677 }; 678 679 i2c2_pins: i2c2 { 680 groups = "i2c2_a"; 681 function = "i2c2"; 682 }; 683 684 irq0_pins: irq0 { 685 groups = "intc_ex_irq0"; 686 function = "intc_ex"; 687 }; 688 689 keys_pins: keys { 690 pins = "GP_5_17", "GP_5_20", "GP_5_22"; 691 bias-pull-up; 692 }; 693 694 pwm1_pins: pwm1 { 695 groups = "pwm1_a"; 696 function = "pwm1"; 697 }; 698 699 scif1_pins: scif1 { 700 groups = "scif1_data_a", "scif1_ctrl"; 701 function = "scif1"; 702 }; 703 704 scif2_pins: scif2 { 705 groups = "scif2_data_a"; 706 function = "scif2"; 707 }; 708 709 scif_clk_pins: scif_clk { 710 groups = "scif_clk_a"; 711 function = "scif_clk"; 712 }; 713 714 sdhi0_pins: sd0 { 715 groups = "sdhi0_data4", "sdhi0_ctrl"; 716 function = "sdhi0"; 717 power-source = <3300>; 718 }; 719 720 sdhi0_pins_uhs: sd0_uhs { 721 groups = "sdhi0_data4", "sdhi0_ctrl"; 722 function = "sdhi0"; 723 power-source = <1800>; 724 }; 725 726 sdhi2_pins: sd2 { 727 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; 728 function = "sdhi2"; 729 power-source = <1800>; 730 }; 731 732 sdhi3_pins: sd3 { 733 groups = "sdhi3_data4", "sdhi3_ctrl"; 734 function = "sdhi3"; 735 power-source = <3300>; 736 }; 737 738 sdhi3_pins_uhs: sd3_uhs { 739 groups = "sdhi3_data4", "sdhi3_ctrl"; 740 function = "sdhi3"; 741 power-source = <1800>; 742 }; 743 744 sound_pins: sound { 745 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; 746 function = "ssi"; 747 }; 748 749 sound_clk_pins: sound_clk { 750 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", 751 "audio_clkout_a", "audio_clkout3_a"; 752 function = "audio_clk"; 753 }; 754 755 usb0_pins: usb0 { 756 groups = "usb0"; 757 function = "usb0"; 758 }; 759 760 usb1_pins: usb1 { 761 mux { 762 groups = "usb1"; 763 function = "usb1"; 764 }; 765 766 ovc { 767 pins = "GP_6_27"; 768 bias-pull-up; 769 }; 770 771 pwen { 772 pins = "GP_6_26"; 773 bias-pull-down; 774 }; 775 }; 776 777 usb30_pins: usb30 { 778 groups = "usb30"; 779 function = "usb30"; 780 }; 781}; 782 783&pwm1 { 784 pinctrl-0 = <&pwm1_pins>; 785 pinctrl-names = "default"; 786 787 status = "okay"; 788}; 789 790&rcar_sound { 791 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; 792 pinctrl-names = "default"; 793 794 /* Single DAI */ 795 #sound-dai-cells = <0>; 796 797 /* audio_clkout0/1/2/3 */ 798 #clock-cells = <1>; 799 clock-frequency = <12288000 11289600>; 800 801 status = "okay"; 802 803 /* update <audio_clk_b> to <cs2000> */ 804 clocks = <&cpg CPG_MOD 1005>, 805 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, 806 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, 807 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, 808 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, 809 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, 810 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, 811 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, 812 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, 813 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, 814 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, 815 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 816 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 817 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, 818 <&audio_clk_a>, <&cs2000>, 819 <&audio_clk_c>, 820 <&cpg CPG_CORE CPG_AUDIO_CLK_I>; 821 822 ports { 823 #address-cells = <1>; 824 #size-cells = <0>; 825 rsnd_port0: port@0 { 826 reg = <0>; 827 rsnd_endpoint0: endpoint { 828 remote-endpoint = <&ak4613_endpoint>; 829 830 dai-format = "left_j"; 831 bitclock-master = <&rsnd_endpoint0>; 832 frame-master = <&rsnd_endpoint0>; 833 834 playback = <&ssi0>, <&src0>, <&dvc0>; 835 capture = <&ssi1>, <&src1>, <&dvc1>; 836 }; 837 }; 838 839 rsnd_port1: port@1 { 840 reg = <1>; 841 rsnd_endpoint1: endpoint { 842 remote-endpoint = <&dw_hdmi0_snd_in>; 843 844 dai-format = "i2s"; 845 bitclock-master = <&rsnd_endpoint1>; 846 frame-master = <&rsnd_endpoint1>; 847 848 playback = <&ssi2>; 849 }; 850 }; 851 852#ifdef SOC_HAS_HDMI1 853 rsnd_port2: port@2 { 854 reg = <2>; 855 rsnd_endpoint2: endpoint { 856 remote-endpoint = <&dw_hdmi1_snd_in>; 857 858 dai-format = "i2s"; 859 bitclock-master = <&rsnd_endpoint2>; 860 frame-master = <&rsnd_endpoint2>; 861 862 playback = <&ssi3>; 863 }; 864 }; 865#endif /* SOC_HAS_HDMI1 */ 866 }; 867}; 868 869&rwdt { 870 timeout-sec = <60>; 871 status = "okay"; 872}; 873 874#ifdef SOC_HAS_SATA 875&sata { 876 status = "okay"; 877}; 878#endif /* SOC_HAS_SATA */ 879 880&scif1 { 881 pinctrl-0 = <&scif1_pins>; 882 pinctrl-names = "default"; 883 884 uart-has-rtscts; 885 /* Please only enable hscif1 or scif1 */ 886 /* status = "okay"; */ 887}; 888 889&scif2 { 890 pinctrl-0 = <&scif2_pins>; 891 pinctrl-names = "default"; 892 893 status = "okay"; 894}; 895 896&scif_clk { 897 clock-frequency = <14745600>; 898}; 899 900&sdhi0 { 901 pinctrl-0 = <&sdhi0_pins>; 902 pinctrl-1 = <&sdhi0_pins_uhs>; 903 pinctrl-names = "default", "state_uhs"; 904 905 vmmc-supply = <&vcc_sdhi0>; 906 vqmmc-supply = <&vccq_sdhi0>; 907 cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; 908 wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; 909 bus-width = <4>; 910 sd-uhs-sdr50; 911 sd-uhs-sdr104; 912 status = "okay"; 913}; 914 915&sdhi2 { 916 /* used for on-board 8bit eMMC */ 917 pinctrl-0 = <&sdhi2_pins>; 918 pinctrl-1 = <&sdhi2_pins>; 919 pinctrl-names = "default", "state_uhs"; 920 921 vmmc-supply = <®_3p3v>; 922 vqmmc-supply = <®_1p8v>; 923 bus-width = <8>; 924 mmc-hs200-1_8v; 925 mmc-hs400-1_8v; 926 no-sd; 927 no-sdio; 928 non-removable; 929 fixed-emmc-driver-type = <1>; 930 full-pwr-cycle-in-suspend; 931 status = "okay"; 932}; 933 934&sdhi3 { 935 pinctrl-0 = <&sdhi3_pins>; 936 pinctrl-1 = <&sdhi3_pins_uhs>; 937 pinctrl-names = "default", "state_uhs"; 938 939 vmmc-supply = <&vcc_sdhi3>; 940 vqmmc-supply = <&vccq_sdhi3>; 941 cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; 942 wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; 943 bus-width = <4>; 944 sd-uhs-sdr50; 945 sd-uhs-sdr104; 946 status = "okay"; 947}; 948 949&ssi1 { 950 shared-pin; 951}; 952 953&usb_extal_clk { 954 clock-frequency = <50000000>; 955}; 956 957&usb2_phy0 { 958 pinctrl-0 = <&usb0_pins>; 959 pinctrl-names = "default"; 960 961 vbus-supply = <&vbus0_usb2>; 962 status = "okay"; 963}; 964 965&usb2_phy1 { 966 pinctrl-0 = <&usb1_pins>; 967 pinctrl-names = "default"; 968 969 status = "okay"; 970}; 971 972&usb3_peri0 { 973 phys = <&usb3_phy0>; 974 phy-names = "usb"; 975 976 companion = <&xhci0>; 977 978 status = "okay"; 979}; 980 981&usb3_phy0 { 982 status = "okay"; 983}; 984 985&usb3s0_clk { 986 clock-frequency = <100000000>; 987}; 988 989&vin0 { 990 status = "okay"; 991}; 992 993&vin1 { 994 status = "okay"; 995}; 996 997&vin2 { 998 status = "okay"; 999}; 1000 1001&vin3 { 1002 status = "okay"; 1003}; 1004 1005&vin4 { 1006 status = "okay"; 1007}; 1008 1009&vin5 { 1010 status = "okay"; 1011}; 1012 1013&vin6 { 1014 status = "okay"; 1015}; 1016 1017&vin7 { 1018 status = "okay"; 1019}; 1020 1021&xhci0 { 1022 pinctrl-0 = <&usb30_pins>; 1023 pinctrl-names = "default"; 1024 1025 status = "okay"; 1026}; 1027 1028#ifdef SOC_HAS_USB2_CH2 1029&ehci2 { 1030 status = "okay"; 1031}; 1032 1033&ohci2 { 1034 status = "okay"; 1035}; 1036 1037&pfc { 1038 usb2_pins: usb2 { 1039 groups = "usb2"; 1040 function = "usb2"; 1041 }; 1042}; 1043 1044&usb2_phy2 { 1045 pinctrl-0 = <&usb2_pins>; 1046 pinctrl-names = "default"; 1047 1048 status = "okay"; 1049}; 1050#endif /* SOC_HAS_USB2_CH2 */ 1051