xref: /freebsd/sys/contrib/device-tree/Bindings/pinctrl/st,stm32-hdp.yaml (revision 833e5d42ab135b0238e61c5b3c19b8619677cbfa)

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (C) STMicroelectronics 2025.
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/st,stm32-hdp.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: STM32 Hardware Debug Port Mux/Config

maintainers:
  - Clément LE GOFFIC <legoffic.clement@gmail.com>

description:
  STMicroelectronics's STM32 MPUs integrate a Hardware Debug Port (HDP).
  It allows to output internal signals on SoC's GPIO.

properties:
  compatible:
    enum:
      - st,stm32mp131-hdp
      - st,stm32mp151-hdp
      - st,stm32mp251-hdp

  reg:
    maxItems: 1

  clocks:
    maxItems: 1

patternProperties:
  "^hdp[0-7]-pins$":
    type: object
    $ref: pinmux-node.yaml#
    additionalProperties: false

    properties:
      pins:
        pattern: '^HDP[0-7]$'

      function: true

    required:
      - function
      - pins

allOf:
  - $ref: pinctrl.yaml#
  - if:
      properties:
        compatible:
          contains:
            const: st,stm32mp131-hdp
    then:
      patternProperties:
        "^hdp[0-7]-pins$":
          properties:
            function:
              enum: [ pwr_pwrwake_sys, pwr_stop_forbidden, pwr_stdby_wakeup, pwr_encomp_vddcore,
                      bsec_out_sec_niden, aiec_sys_wakeup, none, ddrctrl_lp_req,
                      pwr_ddr_ret_enable_n, dts_clk_ptat, sram3ctrl_tamp_erase_act, gpoval0,
                      pwr_sel_vth_vddcpu, pwr_mpu_ram_lowspeed, ca7_naxierrirq, pwr_okin_mr,
                      bsec_out_sec_dbgen, aiec_c1_wakeup, rcc_pwrds_mpu, ddrctrl_dfi_ctrlupd_req,
                      ddrctrl_cactive_ddrc_asr, sram3ctrl_hw_erase_act, nic400_s0_bready, gpoval1,
                      pwr_pwrwake_mpu, pwr_mpu_clock_disable_ack, ca7_ndbgreset_i,
                      bsec_in_rstcore_n, bsec_out_sec_bsc_dis, ddrctrl_dfi_init_complete,
                      ddrctrl_perf_op_is_refresh, ddrctrl_gskp_dfi_lp_req, sram3ctrl_sw_erase_act,
                      nic400_s0_bvalid, gpoval2, pwr_sel_vth_vddcore, pwr_mpu_clock_disable_req,
                      ca7_npmuirq0, ca7_nfiqout0, bsec_out_sec_dftlock, bsec_out_sec_jtag_dis,
                      rcc_pwrds_sys, sram3ctrl_tamp_erase_req, ddrctrl_stat_ddrc_reg_selfref_type0,
                      dts_valobus1_0, dts_valobus2_0, tamp_potential_tamp_erfcfg, nic400_s0_wready,
                      nic400_s0_rready, gpoval3, pwr_stop2_active, ca7_nl2reset_i,
                      ca7_npreset_varm_i, bsec_out_sec_dften, bsec_out_sec_dbgswenable,
                      eth1_out_pmt_intr_o, eth2_out_pmt_intr_o, ddrctrl_stat_ddrc_reg_selfref_type1,
                      ddrctrl_cactive_0, dts_valobus1_1, dts_valobus2_1, tamp_nreset_sram_ercfg,
                      nic400_s0_wlast, nic400_s0_rlast, gpoval4, ca7_standbywfil2,
                      pwr_vth_vddcore_ack, ca7_ncorereset_i, ca7_nirqout0, bsec_in_pwrok,
                      bsec_out_sec_deviceen, eth1_out_lpi_intr_o, eth2_out_lpi_intr_o,
                      ddrctrl_cactive_ddrc, ddrctrl_wr_credit_cnt, dts_valobus1_2, dts_valobus2_2,
                      pka_pka_itamp_out, nic400_s0_wvalid, nic400_s0_rvalid, gpoval5,
                      ca7_standbywfe0, pwr_vth_vddcpu_ack, ca7_evento, bsec_in_tamper_det,
                      bsec_out_sec_spniden, eth1_out_mac_speed_o1, eth2_out_mac_speed_o1,
                      ddrctrl_csysack_ddrc, ddrctrl_lpr_credit_cnt, dts_valobus1_3, dts_valobus2_3,
                      saes_tamper_out, nic400_s0_awready, nic400_s0_arready, gpoval6,
                      ca7_standbywfi0, pwr_rcc_vcpu_rdy, ca7_eventi, ca7_dbgack0, bsec_out_fuse_ok,
                      bsec_out_sec_spiden, eth1_out_mac_speed_o0, eth2_out_mac_speed_o0,
                      ddrctrl_csysreq_ddrc, ddrctrl_hpr_credit_cnt, dts_valobus1_4, dts_valobus2_4,
                      rng_tamper_out, nic400_s0_awavalid, nic400_s0_aravalid, gpoval7 ]
  - if:
      properties:
        compatible:
          contains:
            const: st,stm32mp151-hdp
    then:
      patternProperties:
        "^hdp[0-7]-pins$":
          properties:
            function:
              enum: [ pwr_pwrwake_sys, cm4_sleepdeep, pwr_stdby_wkup, pwr_encomp_vddcore,
                      bsec_out_sec_niden, none, rcc_cm4_sleepdeep, gpu_dbg7, ddrctrl_lp_req,
                      pwr_ddr_ret_enable_n, dts_clk_ptat, gpoval0, pwr_pwrwake_mcu, cm4_halted,
                      ca7_naxierrirq, pwr_okin_mr, bsec_out_sec_dbgen, exti_sys_wakeup,
                      rcc_pwrds_mpu, gpu_dbg6, ddrctrl_dfi_ctrlupd_req, ddrctrl_cactive_ddrc_asr,
                      gpoval1, pwr_pwrwake_mpu, cm4_rxev, ca7_npmuirq1, ca7_nfiqout1,
                      bsec_in_rstcore_n, exti_c2_wakeup, rcc_pwrds_mcu, gpu_dbg5,
                      ddrctrl_dfi_init_complete, ddrctrl_perf_op_is_refresh,
                      ddrctrl_gskp_dfi_lp_req, gpoval2, pwr_sel_vth_vddcore, cm4_txev, ca7_npmuirq0,
                      ca7_nfiqout0, bsec_out_sec_dftlock, exti_c1_wakeup, rcc_pwrds_sys, gpu_dbg4,
                      ddrctrl_stat_ddrc_reg_selfref_type0, ddrctrl_cactive_1, dts_valobus1_0,
                      dts_valobus2_0, gpoval3, pwr_mpu_pdds_not_cstbydis, cm4_sleeping, ca7_nreset1,
                      ca7_nirqout1, bsec_out_sec_dften, bsec_out_sec_dbgswenable,
                      eth_out_pmt_intr_o, gpu_dbg3, ddrctrl_stat_ddrc_reg_selfref_type1,
                      ddrctrl_cactive_0, dts_valobus1_1, dts_valobus2_1, gpoval4, ca7_standbywfil2,
                      pwr_vth_vddcore_ack, ca7_nreset0, ca7_nirqout0, bsec_in_pwrok,
                      bsec_out_sec_deviceen, eth_out_lpi_intr_o, gpu_dbg2, ddrctrl_cactive_ddrc,
                      ddrctrl_wr_credit_cnt, dts_valobus1_2, dts_valobus2_2, gpoval5,
                      ca7_standbywfi1, ca7_standbywfe1, ca7_evento, ca7_dbgack1,
                      bsec_out_sec_spniden, eth_out_mac_speed_o1, gpu_dbg1, ddrctrl_csysack_ddrc,
                      ddrctrl_lpr_credit_cnt, dts_valobus1_3, dts_valobus2_3, gpoval6,
                      ca7_standbywfi0, ca7_standbywfe0, ca7_dbgack0, bsec_out_fuse_ok,
                      bsec_out_sec_spiden, eth_out_mac_speed_o0, gpu_dbg0, ddrctrl_csysreq_ddrc,
                      ddrctrl_hpr_credit_cnt, dts_valobus1_4, dts_valobus2_4, gpoval7 ]
  - if:
      properties:
        compatible:
          contains:
            const: st,stm32mp251-hdp
    then:
      patternProperties:
        "^hdp[0-7]-pins$":
          properties:
            function:
              enum: [ pwr_pwrwake_sys, cpu2_sleep_deep, bsec_out_tst_sdr_unlock_or_disable_scan,
                      bsec_out_nidenm, bsec_out_nidena, cpu2_state_0, rcc_pwrds_sys, gpu_dbg7,
                      ddrss_csysreq_ddrc, ddrss_dfi_phyupd_req, cpu3_sleep_deep,
                      d2_gbl_per_clk_bus_req, pcie_usb_cxpl_debug_info_ei_0,
                      pcie_usb_cxpl_debug_info_ei_8, d3_state_0, gpoval0, pwr_pwrwake_cpu2,
                      cpu2_halted, cpu2_state_1, bsec_out_dbgenm, bsec_out_dbgena, exti1_sys_wakeup,
                      rcc_pwrds_cpu2, gpu_dbg6, ddrss_csysack_ddrc, ddrss_dfi_phymstr_req,
                      cpu3_halted, d2_gbl_per_dma_req, pcie_usb_cxpl_debug_info_ei_1,
                      pcie_usb_cxpl_debug_info_ei_9, d3_state_1, gpoval1, pwr_pwrwake_cpu1,
                      cpu2_rxev, cpu1_npumirq1, cpu1_nfiqout1, bsec_out_shdbgen, exti1_cpu2_wakeup,
                      rcc_pwrds_cpu1, gpu_dbg5, ddrss_cactive_ddrc, ddrss_dfi_lp_req, cpu3_rxev,
                      hpdma1_clk_bus_req, pcie_usb_cxpl_debug_info_ei_2,
                      pcie_usb_cxpl_debug_info_ei_10, d3_state_2, gpoval2, pwr_sel_vth_vddcpu,
                      cpu2_txev, cpu1_npumirq0, cpu1_nfiqout0, bsec_out_ddbgen, exti1_cpu1_wakeup,
                      cpu3_state_0, gpu_dbg4, ddrss_mcdcg_en, ddrss_dfi_freq_0, cpu3_txev,
                      hpdma2_clk_bus_req, pcie_usb_cxpl_debug_info_ei_3,
                      pcie_usb_cxpl_debug_info_ei_11, d1_state_0, gpoval3, pwr_sel_vth_vddcore,
                      cpu2_sleeping, cpu1_evento, cpu1_nirqout1, bsec_out_spnidena, exti2_d3_wakeup,
                      eth1_out_pmt_intr_o, gpu_dbg3, ddrss_dphycg_en, ddrss_obsp0, cpu3_sleeping,
                      hpdma3_clk_bus_req, pcie_usb_cxpl_debug_info_ei_4,
                      pcie_usb_cxpl_debug_info_ei_12, d1_state_1, gpoval4, cpu1_standby_wfil2,
                      none, cpu1_nirqout0, bsec_out_spidena, exti2_cpu3_wakeup, eth1_out_lpi_intr_o,
                      gpu_dbg2, ddrctrl_dfi_init_start, ddrss_obsp1, cpu3_state_1,
                      d3_gbl_per_clk_bus_req, pcie_usb_cxpl_debug_info_ei_5,
                      pcie_usb_cxpl_debug_info_ei_13, d1_state_2, gpoval5, cpu1_standby_wfi1,
                      cpu1_standby_wfe1, cpu1_halted1, cpu1_naxierrirq, bsec_out_spnidenm,
                      exti2_cpu2_wakeup, eth2_out_pmt_intr_o, gpu_dbg1, ddrss_dfi_init_complete,
                      ddrss_obsp2, d2_state_0, d3_gbl_per_dma_req, pcie_usb_cxpl_debug_info_ei_6,
                      pcie_usb_cxpl_debug_info_ei_14, cpu1_state_0, gpoval6, cpu1_standby_wfi0,
                      cpu1_standby_wfe0, cpu1_halted0, bsec_out_spidenm, exti2_cpu1__wakeup,
                      eth2_out_lpi_intr_o, gpu_dbg0, ddrss_dfi_ctrlupd_req, ddrss_obsp3, d2_state_1,
                      lpdma1_clk_bus_req, pcie_usb_cxpl_debug_info_ei_7,
                      pcie_usb_cxpl_debug_info_ei_15, cpu1_state_1, gpoval7 ]

required:
  - compatible
  - reg
  - clocks

additionalProperties: false

examples:
  - |
    #include <dt-bindings/clock/stm32mp1-clks.h>

    pinctrl@54090000 {
      compatible = "st,stm32mp151-hdp";
      reg = <0x54090000 0x400>;
      clocks = <&rcc HDP>;
      pinctrl-names = "default";
      pinctrl-0 = <&hdp2_gpo>;
      hdp2_gpo: hdp2-pins {
        function = "gpoval2";
        pins = "HDP2";
      };
    };