1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/media/i2c/onnn,mt9m114.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: onsemi 1/6-inch 720p CMOS Digital Image Sensor 8 9maintainers: 10 - Laurent Pinchart <laurent.pinchart@ideasonboard.com> 11 12description: |- 13 The onsemi MT9M114 is a 1/6-inch 720p (1.26 Mp) CMOS digital image sensor 14 with an active pixel-array size of 1296H x 976V. It is programmable through 15 an I2C interface and outputs image data over a 8-bit parallel or 1-lane MIPI 16 CSI-2 connection. 17 18properties: 19 compatible: 20 const: onnn,mt9m114 21 22 reg: 23 description: I2C device address 24 enum: 25 - 0x48 26 - 0x5d 27 28 clocks: 29 description: EXTCLK clock signal 30 maxItems: 1 31 32 vdd-supply: 33 description: 34 Core digital voltage supply, 1.8V 35 36 vddio-supply: 37 description: 38 I/O digital voltage supply, 1.8V or 2.8V 39 40 vaa-supply: 41 description: 42 Analog voltage supply, 2.8V 43 44 reset-gpios: 45 description: |- 46 Reference to the GPIO connected to the RESET_BAR pin, if any (active 47 low). 48 49 port: 50 $ref: /schemas/graph.yaml#/$defs/port-base 51 additionalProperties: false 52 53 properties: 54 endpoint: 55 $ref: /schemas/media/video-interfaces.yaml# 56 additionalProperties: false 57 58 properties: 59 bus-type: 60 enum: [4, 5, 6] 61 62 link-frequencies: true 63 remote-endpoint: true 64 65 # The number and mapping of lanes (for CSI-2), and the bus width and 66 # signal polarities (for parallel and BT.656) are fixed and must not 67 # be specified. 68 69 required: 70 - bus-type 71 - link-frequencies 72 73required: 74 - compatible 75 - reg 76 - clocks 77 - vdd-supply 78 - vddio-supply 79 - vaa-supply 80 - port 81 82additionalProperties: false 83 84examples: 85 - | 86 #include <dt-bindings/gpio/gpio.h> 87 #include <dt-bindings/media/video-interfaces.h> 88 89 i2c0 { 90 #address-cells = <1>; 91 #size-cells = <0>; 92 93 sensor@48 { 94 compatible = "onnn,mt9m114"; 95 reg = <0x48>; 96 97 clocks = <&clk24m 0>; 98 99 reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; 100 101 vddio-supply = <®_cam_1v8>; 102 vdd-supply = <®_cam_1v8>; 103 vaa-supply = <®_2p8v>; 104 105 port { 106 endpoint { 107 bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>; 108 link-frequencies = /bits/ 64 <384000000>; 109 remote-endpoint = <&mipi_csi_in>; 110 }; 111 }; 112 }; 113 }; 114... 115