xref: /freebsd/sys/contrib/device-tree/Bindings/clock/zynq-7000.txt (revision c66ec88fed842fbaad62c30d510644ceb7bd2d71)

Device Tree Clock bindings for the Zynq 7000 EPP

The Zynq EPP has several different clk providers, each with there own bindings.
The purpose of this document is to document their usage.

See clock_bindings.txt for more information on the generic clock bindings.
See Chapter 25 of Zynq TRM for more information about Zynq clocks.

== Clock Controller ==
The clock controller is a logical abstraction of Zynq's clock tree. It reads
required input clock frequencies from the devicetree and acts as clock provider
for all clock consumers of PS clocks.

Required properties:
 - #clock-cells : Must be 1
 - compatible : "xlnx,ps7-clkc"
 - reg : SLCR offset and size taken via syscon < 0x100 0x100 >
 - ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ
		      (usually 33 MHz oscillators are used for Zynq platforms)
 - clock-output-names : List of strings used to name the clock outputs. Shall be
			a list of the outputs given below.

Optional properties:
 - clocks : as described in the clock bindings
 - clock-names : as described in the clock bindings
 - fclk-enable : Bit mask to enable FCLKs statically at boot time.
		 Bit [0..3] correspond to FCLK0..FCLK3. The corresponding
		 FCLK will only be enabled if it is actually running at
		 boot time.

Clock inputs:
The following strings are optional parameters to the 'clock-names' property in
order to provide an optional (E)MIO clock source.
 - swdt_ext_clk
 - gem0_emio_clk
 - gem1_emio_clk
 - mio_clk_XX		# with XX = 00..53
...

Clock outputs:
 0:  armpll
 1:  ddrpll
 2:  iopll
 3:  cpu_6or4x
 4:  cpu_3or2x
 5:  cpu_2x
 6:  cpu_1x
 7:  ddr2x
 8:  ddr3x
 9:  dci
 10: lqspi
 11: smc
 12: pcap
 13: gem0
 14: gem1
 15: fclk0
 16: fclk1
 17: fclk2
 18: fclk3
 19: can0
 20: can1
 21: sdio0
 22: sdio1
 23: uart0
 24: uart1
 25: spi0
 26: spi1
 27: dma
 28: usb0_aper
 29: usb1_aper
 30: gem0_aper
 31: gem1_aper
 32: sdio0_aper
 33: sdio1_aper
 34: spi0_aper
 35: spi1_aper
 36: can0_aper
 37: can1_aper
 38: i2c0_aper
 39: i2c1_aper
 40: uart0_aper
 41: uart1_aper
 42: gpio_aper
 43: lqspi_aper
 44: smc_aper
 45: swdt
 46: dbg_trc
 47: dbg_apb

Example:
	clkc: clkc@100 {
		#clock-cells = <1>;
		compatible = "xlnx,ps7-clkc";
		ps-clk-frequency = <33333333>;
		reg = <0x100 0x100>;
		clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
				"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
				"dci", "lqspi", "smc", "pcap", "gem0", "gem1",
				"fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
				"sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1",
				"dma", "usb0_aper", "usb1_aper", "gem0_aper",
				"gem1_aper", "sdio0_aper", "sdio1_aper",
				"spi0_aper", "spi1_aper", "can0_aper", "can1_aper",
				"i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper",
				"gpio_aper", "lqspi_aper", "smc_aper", "swdt",
				"dbg_trc", "dbg_apb";
		# optional props
		clocks = <&clkc 16>, <&clk_foo>;
		clock-names = "gem1_emio_clk", "can_mio_clk_23";
	};