| /freebsd/sys/dev/iicbus/mux/ |
| H A D | iicmux.h | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | iicmux_if.m | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | iic_gpiomux.c | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | iicmux.c | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | ltc430x.c | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/share/man/man4/ |
| H A D | iicmux.4 | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | iic_gpiomux.4 | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | ltc430x.4 | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | Makefile | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/modules/i2c/mux/ltc430x/ |
| H A D | Makefile | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/modules/i2c/mux/iic_gpiomux/ |
| H A D | Makefile | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/modules/i2c/mux/ |
| H A D | Makefile | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/modules/i2c/mux/iicmux/ |
| H A D | Makefile | 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/dev/iicbus/ |
| H A D | iiconf.h | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | iiconf.c | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/modules/i2c/ |
| H A D | Makefile | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| /freebsd/sys/conf/ |
| H A D | NOTES | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|
| H A D | files | diff 422d05da14fe063e5d187d81a328fa7b362d069f Thu Jan 02 18:51:49 CET 2020 Ian Lepore <ian@FreeBSD.org> Add support for i2c bus mux hardware.
An i2c bus can be divided into segments which can be selectively connected
and disconnected from the main bus. This is usually done to enable using
multiple slave devices having the same address, by isolating the devices
onto separate bus segments, only one of which is connected to the main bus
at once.
There are several types of i2c bus muxes, which break down into two general
categories...
- Muxes which are themselves i2c slaves. These devices respond to i2c
commands on their upstream bus, and based on those commands, connect
various downstream buses to the upstream. In newbus terms, they are both
a child of an iicbus and the parent of one or more iicbus instances.
- Muxes which are not i2c devices themselves. Such devices are part of the
i2c bus electrically, but in newbus terms their parent is some other
bus. The association with the upstream bus must be established by
separate metadata (such as FDT data).
In both cases, the mux driver has one or more iicbus child instances
representing the downstream buses. The mux driver implements the iicbus_if
interface, as if it were an iichb host bridge/i2c controller driver. It
services the IO requests sent to it by forwarding them to the iicbus
instance representing the upstream bus, after electrically connecting the
upstream bus to the downstream bus that hosts the i2c slave device which
made the IO request.
The net effect is automatic mux switching which is transparent to slaves on
the downstream buses. They just do i2c IO they way they normally do, and the
bus is electrically connected for the duration of the IO and then idled when
it is complete.
The existing iicbus_if callback() method is enhanced so that the parameter
passed to it can be a struct which contains a device_t for the requesting
bus and slave devices. This change is done by adding a flag that indicates
the extra values are present, and making the flags field the first field of
a new args struct. If the flag is set, the iichb or mux driver can recast
the pointer-to-flags into a pointer-to-struct and access the extra
fields. Thus abi compatibility with older drivers is retained (but a mux
cannot exist on the bus with the older iicbus driver in use.)
A new set of core support routines exists in iicbus.c. This code will help
implement mux drivers for any type of mux hardware by supplying all the
boilerplate code that forwards IO requests upstream. It also has code for
parsing metadata and instantiating the child iicbus instances based on it.
Two new hardware mux drivers are added. The ltc430x driver supports the
LTC4305/4306 mux chips which are controlled via i2c commands. The
iic_gpiomux driver supports any mux hardware which is controlled by
manipulating the state of one or more gpio pins. Test Plan
Tested locally using a variety of mux'd bus configurations involving both
ltc4305 and a homebrew gpio-controlled mux. Tested configurations included
cascaded muxes (unlikely in the real world, but useful to prove that 'it all
just works' in terms of the automatic switching and upstream forwarding of
IO requests).
|