/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2009 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ /* * Common x86 and SPARC PCI-E to PCI bus bridge nexus driver */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* prom_printf */ #include #include #include "pcieb.h" #ifdef PX_PLX #include #endif /* PX_PLX */ /*LINTLIBRARY*/ /* panic flag */ int pcieb_die = PF_ERR_FATAL_FLAGS; /* flag to turn on MSI support */ int pcieb_enable_msi = 1; #if defined(DEBUG) uint_t pcieb_dbg_print = 0; static char *pcieb_debug_sym [] = { /* same sequence as pcieb_debug_bit */ /* 0 */ "attach", /* 1 */ "pwr", /* 2 */ "intr" }; #endif /* DEBUG */ static int pcieb_bus_map(dev_info_t *, dev_info_t *, ddi_map_req_t *, off_t, off_t, caddr_t *); static int pcieb_ctlops(dev_info_t *, dev_info_t *, ddi_ctl_enum_t, void *, void *); static int pcieb_fm_init(pcieb_devstate_t *pcieb_p); static void pcieb_fm_fini(pcieb_devstate_t *pcieb_p); static int pcieb_fm_init_child(dev_info_t *dip, dev_info_t *cdip, int cap, ddi_iblock_cookie_t *ibc_p); static int pcieb_dma_allochdl(dev_info_t *dip, dev_info_t *rdip, ddi_dma_attr_t *attr_p, int (*waitfp)(caddr_t), caddr_t arg, ddi_dma_handle_t *handlep); static int pcieb_dma_mctl(dev_info_t *dip, dev_info_t *rdip, ddi_dma_handle_t handle, enum ddi_dma_ctlops cmd, off_t *offp, size_t *lenp, caddr_t *objp, uint_t cache_flags); static int pcieb_intr_ops(dev_info_t *dip, dev_info_t *rdip, ddi_intr_op_t intr_op, ddi_intr_handle_impl_t *hdlp, void *result); static struct bus_ops pcieb_bus_ops = { BUSO_REV, pcieb_bus_map, 0, 0, 0, i_ddi_map_fault, ddi_dma_map, pcieb_dma_allochdl, ddi_dma_freehdl, ddi_dma_bindhdl, ddi_dma_unbindhdl, ddi_dma_flush, ddi_dma_win, pcieb_dma_mctl, pcieb_ctlops, ddi_bus_prop_op, ndi_busop_get_eventcookie, /* (*bus_get_eventcookie)(); */ ndi_busop_add_eventcall, /* (*bus_add_eventcall)(); */ ndi_busop_remove_eventcall, /* (*bus_remove_eventcall)(); */ ndi_post_event, /* (*bus_post_event)(); */ NULL, /* (*bus_intr_ctl)(); */ NULL, /* (*bus_config)(); */ NULL, /* (*bus_unconfig)(); */ pcieb_fm_init_child, /* (*bus_fm_init)(); */ NULL, /* (*bus_fm_fini)(); */ i_ndi_busop_access_enter, /* (*bus_fm_access_enter)(); */ i_ndi_busop_access_exit, /* (*bus_fm_access_exit)(); */ pcie_bus_power, /* (*bus_power)(); */ pcieb_intr_ops /* (*bus_intr_op)(); */ }; static int pcieb_open(dev_t *, int, int, cred_t *); static int pcieb_close(dev_t, int, int, cred_t *); static int pcieb_ioctl(dev_t, int, intptr_t, int, cred_t *, int *); static int pcieb_prop_op(dev_t, dev_info_t *, ddi_prop_op_t, int, char *, caddr_t, int *); static int pcieb_info(dev_info_t *, ddi_info_cmd_t, void *, void **); static uint_t pcieb_intr_handler(caddr_t arg1, caddr_t arg2); /* PM related functions */ static int pcieb_pwr_setup(dev_info_t *dip); static int pcieb_pwr_init_and_raise(dev_info_t *dip, pcie_pwr_t *pwr_p); static void pcieb_pwr_teardown(dev_info_t *dip); static int pcieb_pwr_disable(dev_info_t *dip); /* Hotplug related functions */ static int pcieb_pciehpc_probe(dev_info_t *dip, ddi_acc_handle_t config_handle); static int pcieb_pcishpc_probe(dev_info_t *dip, ddi_acc_handle_t config_handle); static int pcieb_init_hotplug(pcieb_devstate_t *pcieb); static void pcieb_id_props(pcieb_devstate_t *pcieb); /* * soft state pointer */ void *pcieb_state; static struct cb_ops pcieb_cb_ops = { pcieb_open, /* open */ pcieb_close, /* close */ nodev, /* strategy */ nodev, /* print */ nodev, /* dump */ nodev, /* read */ nodev, /* write */ pcieb_ioctl, /* ioctl */ nodev, /* devmap */ nodev, /* mmap */ nodev, /* segmap */ nochpoll, /* poll */ pcieb_prop_op, /* cb_prop_op */ NULL, /* streamtab */ D_NEW | D_MP | D_HOTPLUG, /* Driver compatibility flag */ CB_REV, /* rev */ nodev, /* int (*cb_aread)() */ nodev /* int (*cb_awrite)() */ }; static int pcieb_probe(dev_info_t *); static int pcieb_attach(dev_info_t *devi, ddi_attach_cmd_t cmd); static int pcieb_detach(dev_info_t *devi, ddi_detach_cmd_t cmd); static struct dev_ops pcieb_ops = { DEVO_REV, /* devo_rev */ 0, /* refcnt */ pcieb_info, /* info */ nulldev, /* identify */ pcieb_probe, /* probe */ pcieb_attach, /* attach */ pcieb_detach, /* detach */ nulldev, /* reset */ &pcieb_cb_ops, /* driver operations */ &pcieb_bus_ops, /* bus operations */ pcie_power, /* power */ ddi_quiesce_not_needed, /* quiesce */ }; /* * Module linkage information for the kernel. */ static struct modldrv modldrv = { &mod_driverops, /* Type of module */ "PCIe to PCI nexus driver", &pcieb_ops, /* driver ops */ }; static struct modlinkage modlinkage = { MODREV_1, (void *)&modldrv, NULL }; /* * forward function declarations: */ static void pcieb_uninitchild(dev_info_t *); static int pcieb_initchild(dev_info_t *child); static void pcieb_create_ranges_prop(dev_info_t *, ddi_acc_handle_t); static boolean_t pcieb_is_pcie_device_type(dev_info_t *dip); /* interrupt related declarations */ static int pcieb_msi_supported(dev_info_t *); static int pcieb_intr_attach(pcieb_devstate_t *pcieb); static int pcieb_intr_init(pcieb_devstate_t *pcieb_p, int intr_type); static void pcieb_intr_fini(pcieb_devstate_t *pcieb_p); int _init(void) { int e; if ((e = ddi_soft_state_init(&pcieb_state, sizeof (pcieb_devstate_t), 1)) == 0 && (e = mod_install(&modlinkage)) != 0) ddi_soft_state_fini(&pcieb_state); return (e); } int _fini(void) { int e; if ((e = mod_remove(&modlinkage)) == 0) { ddi_soft_state_fini(&pcieb_state); } return (e); } int _info(struct modinfo *modinfop) { return (mod_info(&modlinkage, modinfop)); } /*ARGSUSED*/ static int pcieb_probe(dev_info_t *devi) { return (DDI_PROBE_SUCCESS); } static int pcieb_attach(dev_info_t *devi, ddi_attach_cmd_t cmd) { int instance; char device_type[8]; pcieb_devstate_t *pcieb; pcie_bus_t *bus_p = PCIE_DIP2UPBUS(devi); ddi_acc_handle_t config_handle = bus_p->bus_cfg_hdl; uint8_t dev_type = bus_p->bus_dev_type; switch (cmd) { case DDI_RESUME: (void) pcie_pwr_resume(devi); return (DDI_SUCCESS); default: return (DDI_FAILURE); case DDI_ATTACH: break; } if (!(PCIE_IS_BDG(bus_p))) { PCIEB_DEBUG(DBG_ATTACH, devi, "This is not a switch or" " bridge\n"); return (DDI_FAILURE); } /* * If PCIE_LINKCTL_LINK_DISABLE bit in the PCIe Config * Space (PCIe Capability Link Control Register) is set, * then do not bind the driver. */ if (PCIE_CAP_GET(16, bus_p, PCIE_LINKCTL) & PCIE_LINKCTL_LINK_DISABLE) return (DDI_FAILURE); /* * Allocate and get soft state structure. */ instance = ddi_get_instance(devi); if (ddi_soft_state_zalloc(pcieb_state, instance) != DDI_SUCCESS) return (DDI_FAILURE); pcieb = ddi_get_soft_state(pcieb_state, instance); pcieb->pcieb_dip = devi; pcieb->pcieb_soft_state = PCIEB_SOFT_STATE_CLOSED; if ((pcieb_fm_init(pcieb)) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, devi, "Failed in pcieb_fm_init\n"); goto fail; } pcieb->pcieb_init_flags |= PCIEB_INIT_FM; mutex_init(&pcieb->pcieb_mutex, NULL, MUTEX_DRIVER, NULL); mutex_init(&pcieb->pcieb_err_mutex, NULL, MUTEX_DRIVER, (void *)pcieb->pcieb_fm_ibc); mutex_init(&pcieb->pcieb_peek_poke_mutex, NULL, MUTEX_DRIVER, (void *)pcieb->pcieb_fm_ibc); /* create special properties for device identification */ pcieb_id_props(pcieb); /* * Power management setup. This also makes sure that switch/bridge * is at D0 during attach. */ if (pwr_common_setup(devi) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_PWR, devi, "pwr_common_setup failed\n"); goto fail; } if (pcieb_pwr_setup(devi) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_PWR, devi, "pxb_pwr_setup failed \n"); goto fail; } /* * Make sure the "device_type" property exists. */ if (pcieb_is_pcie_device_type(devi)) (void) strcpy(device_type, "pciex"); else (void) strcpy(device_type, "pci"); (void) ddi_prop_update_string(DDI_DEV_T_NONE, devi, "device_type", device_type); /* * Check whether the "ranges" property is present. * Otherwise create the ranges property by reading * the configuration registers */ if (ddi_prop_exists(DDI_DEV_T_ANY, devi, DDI_PROP_DONTPASS, "ranges") == 0) { pcieb_create_ranges_prop(devi, config_handle); } if (PCIE_IS_PCI_BDG(bus_p)) pcieb_set_pci_perf_parameters(devi, config_handle); #ifdef PX_PLX pcieb_attach_plx_workarounds(pcieb); #endif /* PX_PLX */ /* Initialize hotplug */ pcieb->pcieb_hotplug_capable = B_FALSE; if ((dev_type == PCIE_PCIECAP_DEV_TYPE_DOWN) || (dev_type == PCIE_PCIECAP_DEV_TYPE_ROOT) || (dev_type == PCIE_PCIECAP_DEV_TYPE_PCIE2PCI) || (dev_type == PCIE_PCIECAP_DEV_TYPE_PCI2PCIE)) { (void) pcieb_init_hotplug(pcieb); } /* * Initialize interrupt handlers. Ignore return value. */ (void) pcieb_intr_attach(pcieb); if (pcieb->pcieb_hotplug_capable == B_FALSE) { /* * (for non hotplug bus) this would create ":devctl" minor * node to support DEVCTL_DEVICE_* and DEVCTL_BUS_* ioctls * to this bus. */ if (ddi_create_minor_node(devi, "devctl", S_IFCHR, PCIHP_AP_MINOR_NUM(instance, PCIHP_DEVCTL_MINOR), DDI_NT_NEXUS, 0) != DDI_SUCCESS) goto fail; } PCIEB_DEBUG(DBG_ATTACH, devi, "pcieb_attach: this nexus %s hotplug slots\n", pcieb->pcieb_hotplug_capable == B_TRUE ? "has":"has no"); /* Do any platform specific workarounds needed at this time */ pcieb_plat_attach_workaround(devi); /* * If this is a root port, determine and set the max payload size. * Since this will involve scanning the fabric, all error enabling * and sw workarounds should be in place before doing this. */ if (PCIE_IS_RP(bus_p)) pcie_init_root_port_mps(devi); ddi_report_dev(devi); return (DDI_SUCCESS); fail: (void) pcieb_detach(devi, DDI_DETACH); return (DDI_FAILURE); } static int pcieb_detach(dev_info_t *devi, ddi_detach_cmd_t cmd) { pcieb_devstate_t *pcieb; int error = DDI_SUCCESS; switch (cmd) { case DDI_SUSPEND: error = pcie_pwr_suspend(devi); return (error); case DDI_DETACH: break; default: return (DDI_FAILURE); } pcieb = ddi_get_soft_state(pcieb_state, ddi_get_instance(devi)); /* remove interrupt handlers */ pcieb_intr_fini(pcieb); if (pcieb->pcieb_hotplug_capable == B_TRUE) { if (pcihp_uninit(devi) == DDI_FAILURE) error = DDI_FAILURE; if (pcieb->pcieb_hpc_type == HPC_PCIE) (void) pciehpc_uninit(devi); else if (pcieb->pcieb_hpc_type == HPC_SHPC) (void) pcishpc_uninit(devi); (void) ndi_prop_remove(DDI_DEV_T_NONE, devi, "hotplug-capable"); } else { ddi_remove_minor_node(devi, "devctl"); } (void) ddi_prop_remove(DDI_DEV_T_NONE, devi, "device_type"); (void) ndi_prop_remove(DDI_DEV_T_NONE, pcieb->pcieb_dip, "pcie_ce_mask"); if (pcieb->pcieb_init_flags & PCIEB_INIT_FM) pcieb_fm_fini(pcieb); pcieb_pwr_teardown(devi); pwr_common_teardown(devi); mutex_destroy(&pcieb->pcieb_peek_poke_mutex); mutex_destroy(&pcieb->pcieb_err_mutex); mutex_destroy(&pcieb->pcieb_mutex); /* * And finally free the per-pci soft state. */ ddi_soft_state_free(pcieb_state, ddi_get_instance(devi)); return (DDI_SUCCESS); } static int pcieb_bus_map(dev_info_t *dip, dev_info_t *rdip, ddi_map_req_t *mp, off_t offset, off_t len, caddr_t *vaddrp) { dev_info_t *pdip; pdip = (dev_info_t *)DEVI(dip)->devi_parent; return ((DEVI(pdip)->devi_ops->devo_bus_ops->bus_map)(pdip, rdip, mp, offset, len, vaddrp)); } static int pcieb_ctlops(dev_info_t *dip, dev_info_t *rdip, ddi_ctl_enum_t ctlop, void *arg, void *result) { pci_regspec_t *drv_regp; int reglen; int rn; int totreg; pcieb_devstate_t *pcieb = ddi_get_soft_state(pcieb_state, ddi_get_instance(dip)); struct detachspec *ds; struct attachspec *as; switch (ctlop) { case DDI_CTLOPS_REPORTDEV: if (rdip == (dev_info_t *)0) return (DDI_FAILURE); cmn_err(CE_CONT, "?PCIE-device: %s@%s, %s%d\n", ddi_node_name(rdip), ddi_get_name_addr(rdip), ddi_driver_name(rdip), ddi_get_instance(rdip)); return (DDI_SUCCESS); case DDI_CTLOPS_INITCHILD: return (pcieb_initchild((dev_info_t *)arg)); case DDI_CTLOPS_UNINITCHILD: pcieb_uninitchild((dev_info_t *)arg); return (DDI_SUCCESS); case DDI_CTLOPS_SIDDEV: return (DDI_SUCCESS); case DDI_CTLOPS_REGSIZE: case DDI_CTLOPS_NREGS: if (rdip == (dev_info_t *)0) return (DDI_FAILURE); break; case DDI_CTLOPS_PEEK: case DDI_CTLOPS_POKE: return (pcieb_plat_peekpoke(dip, rdip, ctlop, arg, result)); case DDI_CTLOPS_ATTACH: if (!pcie_is_child(dip, rdip)) return (DDI_SUCCESS); as = (struct attachspec *)arg; switch (as->when) { case DDI_PRE: if (as->cmd == DDI_RESUME) { pcie_clear_errors(rdip); if (pcieb_plat_ctlops(rdip, ctlop, arg) != DDI_SUCCESS) return (DDI_FAILURE); } if (as->cmd == DDI_ATTACH) return (pcie_pm_hold(dip)); return (DDI_SUCCESS); case DDI_POST: if (as->cmd == DDI_ATTACH && as->result != DDI_SUCCESS) pcie_pm_release(dip); if (as->result == DDI_SUCCESS) { pf_init(rdip, (void *)pcieb->pcieb_fm_ibc, as->cmd); (void) pcieb_plat_ctlops(rdip, ctlop, arg); } /* * For empty hotplug-capable slots, we should explicitly * disable the errors, so that we won't panic upon * unsupported hotplug messages. */ if ((!ddi_prop_exists(DDI_DEV_T_ANY, rdip, DDI_PROP_DONTPASS, "hotplug-capable")) || ddi_get_child(rdip)) { (void) pcie_postattach_child(rdip); return (DDI_SUCCESS); } pcie_disable_errors(rdip); return (DDI_SUCCESS); default: break; } return (DDI_SUCCESS); case DDI_CTLOPS_DETACH: if (!pcie_is_child(dip, rdip)) return (DDI_SUCCESS); ds = (struct detachspec *)arg; switch (ds->when) { case DDI_PRE: pf_fini(rdip, ds->cmd); return (DDI_SUCCESS); case DDI_POST: if (pcieb_plat_ctlops(rdip, ctlop, arg) != DDI_SUCCESS) return (DDI_FAILURE); if (ds->cmd == DDI_DETACH && ds->result == DDI_SUCCESS) { return (pcie_pm_remove_child(dip, rdip)); } return (DDI_SUCCESS); default: break; } return (DDI_SUCCESS); default: return (ddi_ctlops(dip, rdip, ctlop, arg, result)); } *(int *)result = 0; if (ddi_getlongprop(DDI_DEV_T_ANY, rdip, DDI_PROP_DONTPASS | DDI_PROP_CANSLEEP, "reg", (caddr_t)&drv_regp, ®len) != DDI_SUCCESS) return (DDI_FAILURE); totreg = reglen / sizeof (pci_regspec_t); if (ctlop == DDI_CTLOPS_NREGS) *(int *)result = totreg; else if (ctlop == DDI_CTLOPS_REGSIZE) { rn = *(int *)arg; if (rn >= totreg) { kmem_free(drv_regp, reglen); return (DDI_FAILURE); } *(off_t *)result = drv_regp[rn].pci_size_low | ((uint64_t)drv_regp[rn].pci_size_hi << 32); } kmem_free(drv_regp, reglen); return (DDI_SUCCESS); } /* * name_child * * This function is called from init_child to name a node. It is * also passed as a callback for node merging functions. * * return value: DDI_SUCCESS, DDI_FAILURE */ static int pcieb_name_child(dev_info_t *child, char *name, int namelen) { pci_regspec_t *pci_rp; uint_t slot, func; char **unit_addr; uint_t n; /* * For .conf nodes, use unit-address property as name */ if (ndi_dev_is_persistent_node(child) == 0) { if (ddi_prop_lookup_string_array(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "unit-address", &unit_addr, &n) != DDI_PROP_SUCCESS) { cmn_err(CE_WARN, "cannot find unit-address in %s.conf", ddi_driver_name(child)); return (DDI_FAILURE); } if (n != 1 || *unit_addr == NULL || **unit_addr == 0) { cmn_err(CE_WARN, "unit-address property in %s.conf" " not well-formed", ddi_driver_name(child)); ddi_prop_free(unit_addr); return (DDI_FAILURE); } (void) snprintf(name, namelen, "%s", *unit_addr); ddi_prop_free(unit_addr); return (DDI_SUCCESS); } /* * Get the address portion of the node name based on * the function and device number. */ if (ddi_prop_lookup_int_array(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "reg", (int **)&pci_rp, &n) != DDI_SUCCESS) { return (DDI_FAILURE); } /* copy the device identifications */ slot = PCI_REG_DEV_G(pci_rp[0].pci_phys_hi); func = PCI_REG_FUNC_G(pci_rp[0].pci_phys_hi); if (func != 0) (void) snprintf(name, namelen, "%x,%x", slot, func); else (void) snprintf(name, namelen, "%x", slot); ddi_prop_free(pci_rp); return (DDI_SUCCESS); } static int pcieb_initchild(dev_info_t *child) { char name[MAXNAMELEN]; int result = DDI_FAILURE; pcieb_devstate_t *pcieb = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, ddi_get_instance(ddi_get_parent(child))); /* * Name the child */ if (pcieb_name_child(child, name, MAXNAMELEN) != DDI_SUCCESS) { result = DDI_FAILURE; goto done; } ddi_set_name_addr(child, name); /* * Pseudo nodes indicate a prototype node with per-instance * properties to be merged into the real h/w device node. * The interpretation of the unit-address is DD[,F] * where DD is the device id and F is the function. */ if (ndi_dev_is_persistent_node(child) == 0) { extern int pci_allow_pseudo_children; /* * Try to merge the properties from this prototype * node into real h/w nodes. */ if (ndi_merge_node(child, pcieb_name_child) != DDI_SUCCESS) { /* * Merged ok - return failure to remove the node. */ ddi_set_name_addr(child, NULL); result = DDI_FAILURE; goto done; } /* workaround for ddivs to run under PCI-E */ if (pci_allow_pseudo_children) { result = DDI_SUCCESS; goto done; } /* * The child was not merged into a h/w node, * but there's not much we can do with it other * than return failure to cause the node to be removed. */ cmn_err(CE_WARN, "!%s@%s: %s.conf properties not merged", ddi_driver_name(child), ddi_get_name_addr(child), ddi_driver_name(child)); ddi_set_name_addr(child, NULL); result = DDI_NOT_WELL_FORMED; goto done; } /* platform specific initchild */ pcieb_plat_initchild(child); if (pcie_pm_hold(pcieb->pcieb_dip) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_PWR, pcieb->pcieb_dip, "INITCHILD: px_pm_hold failed\n"); result = DDI_FAILURE; goto done; } /* Any return from here must call pcie_pm_release */ /* * If configuration registers were previously saved by * child (before it entered D3), then let the child do the * restore to set up the config regs as it'll first need to * power the device out of D3. */ if (ddi_prop_exists(DDI_DEV_T_ANY, child, DDI_PROP_DONTPASS, "config-regs-saved-by-child") == 1) { PCIEB_DEBUG(DBG_PWR, ddi_get_parent(child), "INITCHILD: config regs to be restored by child" " for %s@%s\n", ddi_node_name(child), ddi_get_name_addr(child)); result = DDI_SUCCESS; goto cleanup; } PCIEB_DEBUG(DBG_PWR, ddi_get_parent(child), "INITCHILD: config regs setup for %s@%s\n", ddi_node_name(child), ddi_get_name_addr(child)); if (!pcie_init_bus(child) || pcie_initchild(child) != DDI_SUCCESS) { result = DDI_FAILURE; goto cleanup; } #ifdef PX_PLX if (pcieb_init_plx_workarounds(pcieb, child) == DDI_FAILURE) { result = DDI_FAILURE; goto cleanup; } #endif /* PX_PLX */ result = DDI_SUCCESS; cleanup: pcie_pm_release(pcieb->pcieb_dip); done: return (result); } static void pcieb_uninitchild(dev_info_t *dip) { pcie_uninitchild(dip); pcieb_plat_uninitchild(dip); ddi_set_name_addr(dip, NULL); /* * Strip the node to properly convert it back to prototype form */ ddi_remove_minor_node(dip, NULL); ddi_prop_remove_all(dip); } static boolean_t pcieb_is_pcie_device_type(dev_info_t *dip) { pcie_bus_t *bus_p = PCIE_DIP2BUS(dip); if (PCIE_IS_SW(bus_p) || PCIE_IS_RP(bus_p) || PCIE_IS_PCI2PCIE(bus_p)) return (B_TRUE); return (B_FALSE); } static int pcieb_intr_attach(pcieb_devstate_t *pcieb) { int intr_types; dev_info_t *dip = pcieb->pcieb_dip; /* Allow platform specific code to do any initialization first */ pcieb_plat_intr_attach(pcieb); /* * Initialize interrupt handlers. * If both MSI and FIXED are supported, try to attach MSI first. * If MSI fails for any reason, then try FIXED, but only allow one * type to be attached. */ if (ddi_intr_get_supported_types(dip, &intr_types) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, dip, "ddi_intr_get_supported_types" " failed\n"); goto FAIL; } if ((intr_types & DDI_INTR_TYPE_MSI) && (pcieb_msi_supported(dip) == DDI_SUCCESS)) { if (pcieb_intr_init(pcieb, DDI_INTR_TYPE_MSI) == DDI_SUCCESS) intr_types = DDI_INTR_TYPE_MSI; else { PCIEB_DEBUG(DBG_ATTACH, dip, "Unable to attach MSI" " handler\n"); } } if (intr_types != DDI_INTR_TYPE_MSI) { /* * MSIs are not supported or MSI initialization failed. For Root * Ports mark this so error handling might try to fallback to * some other mechanism if available (machinecheck etc.). */ if (PCIE_IS_RP(PCIE_DIP2UPBUS(dip))) pcieb->pcieb_no_aer_msi = B_TRUE; } if (intr_types & DDI_INTR_TYPE_FIXED) { if (pcieb_intr_init(pcieb, DDI_INTR_TYPE_FIXED) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, dip, "Unable to attach INTx handler\n"); goto FAIL; } } return (DDI_SUCCESS); FAIL: return (DDI_FAILURE); } /* * This function initializes internally generated interrupts only. * It does not affect any interrupts generated by downstream devices * or the forwarding of them. * * Enable Device Specific Interrupts or Hotplug features here. * Enabling features may change how many interrupts are requested * by the device. If features are not enabled first, the * device might not ask for any interrupts. */ static int pcieb_intr_init(pcieb_devstate_t *pcieb, int intr_type) { dev_info_t *dip = pcieb->pcieb_dip; int nintrs, request, count, x; int intr_cap = 0; int inum = 0; int ret, hp_msi_off; pcie_bus_t *bus_p = PCIE_DIP2UPBUS(dip); uint16_t vendorid = bus_p->bus_dev_ven_id & 0xFFFF; boolean_t is_hp = B_FALSE; boolean_t is_pme = B_FALSE; PCIEB_DEBUG(DBG_ATTACH, dip, "pcieb_intr_init: Attaching %s handler\n", (intr_type == DDI_INTR_TYPE_MSI) ? "MSI" : "INTx"); request = 0; if (pcieb->pcieb_hotplug_capable) { request++; is_hp = B_TRUE; } /* * Hotplug and PME share the same MSI vector. If hotplug is not * supported check if MSI is needed for PME. */ if ((intr_type == DDI_INTR_TYPE_MSI) && PCIE_IS_RP(bus_p) && (vendorid == NVIDIA_VENDOR_ID)) { is_pme = B_TRUE; if (!is_hp) request++; } /* * Setup MSI if this device is a Rootport and has AER. Currently no * SPARC Root Port supports fabric errors being reported through it. */ if (intr_type == DDI_INTR_TYPE_MSI) { if (PCIE_IS_RP(bus_p) && PCIE_HAS_AER(bus_p)) request++; } if (request == 0) return (DDI_SUCCESS); /* * Get number of supported interrupts. * * Several Bridges/Switches will not have this property set, resulting * in a FAILURE, if the device is not configured in a way that * interrupts are needed. (eg. hotplugging) */ ret = ddi_intr_get_nintrs(dip, intr_type, &nintrs); if ((ret != DDI_SUCCESS) || (nintrs == 0)) { PCIEB_DEBUG(DBG_ATTACH, dip, "ddi_intr_get_nintrs ret:%d" " req:%d\n", ret, nintrs); return (DDI_FAILURE); } PCIEB_DEBUG(DBG_ATTACH, dip, "bdf 0x%x: ddi_intr_get_nintrs: nintrs %d", " request %d\n", bus_p->bus_bdf, nintrs, request); if (request > nintrs) request = nintrs; /* Allocate an array of interrupt handlers */ pcieb->pcieb_htable_size = sizeof (ddi_intr_handle_t) * request; pcieb->pcieb_htable = kmem_zalloc(pcieb->pcieb_htable_size, KM_SLEEP); pcieb->pcieb_init_flags |= PCIEB_INIT_HTABLE; ret = ddi_intr_alloc(dip, pcieb->pcieb_htable, intr_type, inum, request, &count, DDI_INTR_ALLOC_NORMAL); if ((ret != DDI_SUCCESS) || (count == 0)) { PCIEB_DEBUG(DBG_ATTACH, dip, "ddi_intr_alloc() ret: %d ask: %d" " actual: %d\n", ret, request, count); goto FAIL; } pcieb->pcieb_init_flags |= PCIEB_INIT_ALLOC; /* Save the actual number of interrupts allocated */ pcieb->pcieb_intr_count = count; if (count < request) { PCIEB_DEBUG(DBG_ATTACH, dip, "bdf 0%x: Requested Intr: %d" " Received: %d\n", bus_p->bus_bdf, request, count); } /* * NVidia (MCP55 and other) chipsets have a errata that if the number * of requested MSI intrs is not allocated we have to fall back to INTx. */ if (intr_type == DDI_INTR_TYPE_MSI) { if (PCIE_IS_RP(bus_p) && (vendorid == NVIDIA_VENDOR_ID)) { if (request != count) goto FAIL; } } /* Get interrupt priority */ ret = ddi_intr_get_pri(pcieb->pcieb_htable[0], &pcieb->pcieb_intr_priority); if (ret != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, dip, "ddi_intr_get_pri() ret: %d\n", ret); goto FAIL; } if (pcieb->pcieb_intr_priority >= LOCK_LEVEL) { pcieb->pcieb_intr_priority = LOCK_LEVEL - 1; ret = ddi_intr_set_pri(pcieb->pcieb_htable[0], pcieb->pcieb_intr_priority); if (ret != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, dip, "ddi_intr_set_pri() ret:" " %d\n", ret); goto FAIL; } } mutex_init(&pcieb->pcieb_intr_mutex, NULL, MUTEX_DRIVER, NULL); pcieb->pcieb_init_flags |= PCIEB_INIT_MUTEX; for (count = 0; count < pcieb->pcieb_intr_count; count++) { ret = ddi_intr_add_handler(pcieb->pcieb_htable[count], pcieb_intr_handler, (caddr_t)pcieb, (caddr_t)(uintptr_t)(inum + count)); if (ret != DDI_SUCCESS) { PCIEB_DEBUG(DBG_ATTACH, dip, "Cannot add " "interrupt(%d)\n", ret); break; } } /* If unsucessful, remove the added handlers */ if (ret != DDI_SUCCESS) { for (x = 0; x < count; x++) { (void) ddi_intr_remove_handler(pcieb->pcieb_htable[x]); } goto FAIL; } pcieb->pcieb_init_flags |= PCIEB_INIT_HANDLER; (void) ddi_intr_get_cap(pcieb->pcieb_htable[0], &intr_cap); /* * Get this intr lock because we are not quite ready to handle * interrupts immediately after enabling it. The MSI multi register * gets programmed in ddi_intr_enable after which we need to get the * MSI offsets for Hotplug/AER. */ mutex_enter(&pcieb->pcieb_intr_mutex); if (intr_cap & DDI_INTR_FLAG_BLOCK) { (void) ddi_intr_block_enable(pcieb->pcieb_htable, pcieb->pcieb_intr_count); pcieb->pcieb_init_flags |= PCIEB_INIT_BLOCK; } else { for (count = 0; count < pcieb->pcieb_intr_count; count++) { (void) ddi_intr_enable(pcieb->pcieb_htable[count]); } } pcieb->pcieb_init_flags |= PCIEB_INIT_ENABLE; /* Save the interrupt type */ pcieb->pcieb_intr_type = intr_type; /* Get the MSI offset for hotplug/PME from the PCIe cap reg */ if (intr_type == DDI_INTR_TYPE_MSI) { hp_msi_off = PCI_CAP_GET16(bus_p->bus_cfg_hdl, NULL, bus_p->bus_pcie_off, PCIE_PCIECAP) & PCIE_PCIECAP_INT_MSG_NUM; if (hp_msi_off >= count) { PCIEB_DEBUG(DBG_ATTACH, dip, "MSI number %d in PCIe " "cap > max allocated %d\n", hp_msi_off, count); mutex_exit(&pcieb->pcieb_intr_mutex); goto FAIL; } if (is_hp) pcieb->pcieb_isr_tab[hp_msi_off] |= PCIEB_INTR_SRC_HP; if (is_pme) pcieb->pcieb_isr_tab[hp_msi_off] |= PCIEB_INTR_SRC_PME; } else { /* INTx handles only Hotplug interrupts */ if (is_hp) pcieb->pcieb_isr_tab[0] |= PCIEB_INTR_SRC_HP; } /* * Get the MSI offset for errors from the AER Root Error status * register. */ if ((intr_type == DDI_INTR_TYPE_MSI) && PCIE_IS_RP(bus_p)) { if (PCIE_HAS_AER(bus_p)) { int aer_msi_off; aer_msi_off = (PCI_XCAP_GET32(bus_p->bus_cfg_hdl, NULL, bus_p->bus_aer_off, PCIE_AER_RE_STS) >> PCIE_AER_RE_STS_MSG_NUM_SHIFT) & PCIE_AER_RE_STS_MSG_NUM_MASK; if (aer_msi_off >= count) { PCIEB_DEBUG(DBG_ATTACH, dip, "MSI number %d in" " AER cap > max allocated %d\n", aer_msi_off, count); mutex_exit(&pcieb->pcieb_intr_mutex); goto FAIL; } pcieb->pcieb_isr_tab[aer_msi_off] |= PCIEB_INTR_SRC_AER; } else { /* * This RP does not have AER. Fallback to the * SERR+Machinecheck approach if available. */ pcieb->pcieb_no_aer_msi = B_TRUE; } } mutex_exit(&pcieb->pcieb_intr_mutex); return (DDI_SUCCESS); FAIL: pcieb_intr_fini(pcieb); return (DDI_FAILURE); } static void pcieb_intr_fini(pcieb_devstate_t *pcieb) { int x; int count = pcieb->pcieb_intr_count; int flags = pcieb->pcieb_init_flags; if ((flags & PCIEB_INIT_ENABLE) && (flags & PCIEB_INIT_BLOCK)) { (void) ddi_intr_block_disable(pcieb->pcieb_htable, count); flags &= ~(PCIEB_INIT_ENABLE | PCIEB_INIT_BLOCK); } if (flags & PCIEB_INIT_MUTEX) mutex_destroy(&pcieb->pcieb_intr_mutex); for (x = 0; x < count; x++) { if (flags & PCIEB_INIT_ENABLE) (void) ddi_intr_disable(pcieb->pcieb_htable[x]); if (flags & PCIEB_INIT_HANDLER) (void) ddi_intr_remove_handler(pcieb->pcieb_htable[x]); if (flags & PCIEB_INIT_ALLOC) (void) ddi_intr_free(pcieb->pcieb_htable[x]); } flags &= ~(PCIEB_INIT_ENABLE | PCIEB_INIT_HANDLER | PCIEB_INIT_ALLOC | PCIEB_INIT_MUTEX); if (flags & PCIEB_INIT_HTABLE) kmem_free(pcieb->pcieb_htable, pcieb->pcieb_htable_size); flags &= ~PCIEB_INIT_HTABLE; pcieb->pcieb_init_flags &= flags; } /* * Checks if this device needs MSIs enabled or not. */ /*ARGSUSED*/ static int pcieb_msi_supported(dev_info_t *dip) { return ((pcieb_enable_msi && pcieb_plat_msi_supported(dip)) ? DDI_SUCCESS: DDI_FAILURE); } /*ARGSUSED*/ static int pcieb_fm_init_child(dev_info_t *dip, dev_info_t *tdip, int cap, ddi_iblock_cookie_t *ibc) { pcieb_devstate_t *pcieb = ddi_get_soft_state(pcieb_state, ddi_get_instance(dip)); ASSERT(ibc != NULL); *ibc = pcieb->pcieb_fm_ibc; return (DEVI(dip)->devi_fmhdl->fh_cap | DDI_FM_ACCCHK_CAPABLE | DDI_FM_DMACHK_CAPABLE); } static int pcieb_fm_init(pcieb_devstate_t *pcieb_p) { dev_info_t *dip = pcieb_p->pcieb_dip; int fm_cap = DDI_FM_EREPORT_CAPABLE; /* * Request our capability level and get our parents capability * and ibc. */ ddi_fm_init(dip, &fm_cap, &pcieb_p->pcieb_fm_ibc); return (DDI_SUCCESS); } /* * Breakdown our FMA resources */ static void pcieb_fm_fini(pcieb_devstate_t *pcieb_p) { /* * Clean up allocated fm structures */ ddi_fm_fini(pcieb_p->pcieb_dip); } static int pcieb_open(dev_t *devp, int flags, int otyp, cred_t *credp) { pcieb_devstate_t *pcieb_p; minor_t minor = getminor(*devp); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); /* * Make sure the open is for the right file type. */ if (otyp != OTYP_CHR) return (EINVAL); /* * Get the soft state structure for the device. */ pcieb_p = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, instance); if (pcieb_p == NULL) return (ENXIO); if (pcieb_p->pcieb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_open(devp, flags, otyp, credp)); /* * Handle the open by tracking the device state. */ mutex_enter(&pcieb_p->pcieb_mutex); if (flags & FEXCL) { if (pcieb_p->pcieb_soft_state != PCIEB_SOFT_STATE_CLOSED) { mutex_exit(&pcieb_p->pcieb_mutex); return (EBUSY); } pcieb_p->pcieb_soft_state = PCIEB_SOFT_STATE_OPEN_EXCL; } else { if (pcieb_p->pcieb_soft_state == PCIEB_SOFT_STATE_OPEN_EXCL) { mutex_exit(&pcieb_p->pcieb_mutex); return (EBUSY); } pcieb_p->pcieb_soft_state = PCIEB_SOFT_STATE_OPEN; } mutex_exit(&pcieb_p->pcieb_mutex); return (0); } static int pcieb_close(dev_t dev, int flags, int otyp, cred_t *credp) { pcieb_devstate_t *pcieb_p; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); if (otyp != OTYP_CHR) return (EINVAL); pcieb_p = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, instance); if (pcieb_p == NULL) return (ENXIO); if (pcieb_p->pcieb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_close(dev, flags, otyp, credp)); mutex_enter(&pcieb_p->pcieb_mutex); pcieb_p->pcieb_soft_state = PCIEB_SOFT_STATE_CLOSED; mutex_exit(&pcieb_p->pcieb_mutex); return (0); } static int pcieb_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *credp, int *rvalp) { pcieb_devstate_t *pcieb_p; dev_info_t *self; struct devctl_iocdata *dcp; uint_t bus_state; int rv = 0; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pcieb_p = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, instance); if (pcieb_p == NULL) return (ENXIO); self = pcieb_p->pcieb_dip; if (pcieb_p->pcieb_hotplug_capable == B_TRUE) { rv = ((pcihp_get_cb_ops())->cb_ioctl(dev, cmd, arg, mode, credp, rvalp)); pcieb_plat_ioctl_hotplug(self, rv, cmd); return (rv); } /* * We can use the generic implementation for these ioctls */ switch (cmd) { case DEVCTL_DEVICE_GETSTATE: case DEVCTL_DEVICE_ONLINE: case DEVCTL_DEVICE_OFFLINE: case DEVCTL_BUS_GETSTATE: return (ndi_devctl_ioctl(self, cmd, arg, mode, 0)); } /* * read devctl ioctl data */ if (ndi_dc_allochdl((void *)arg, &dcp) != NDI_SUCCESS) return (EFAULT); switch (cmd) { case DEVCTL_DEVICE_RESET: rv = ENOTSUP; break; case DEVCTL_BUS_QUIESCE: if (ndi_get_bus_state(self, &bus_state) == NDI_SUCCESS) if (bus_state == BUS_QUIESCED) break; (void) ndi_set_bus_state(self, BUS_QUIESCED); break; case DEVCTL_BUS_UNQUIESCE: if (ndi_get_bus_state(self, &bus_state) == NDI_SUCCESS) if (bus_state == BUS_ACTIVE) break; (void) ndi_set_bus_state(self, BUS_ACTIVE); break; case DEVCTL_BUS_RESET: rv = ENOTSUP; break; case DEVCTL_BUS_RESETALL: rv = ENOTSUP; break; default: rv = ENOTTY; } ndi_dc_freehdl(dcp); return (rv); } static int pcieb_prop_op(dev_t dev, dev_info_t *dip, ddi_prop_op_t prop_op, int flags, char *name, caddr_t valuep, int *lengthp) { pcieb_devstate_t *pcieb_p; minor_t minor = getminor(dev); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pcieb_p = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, instance); if (pcieb_p == NULL) return (ENXIO); if (pcieb_p->pcieb_hotplug_capable == B_TRUE) return ((pcihp_get_cb_ops())->cb_prop_op(dev, dip, prop_op, flags, name, valuep, lengthp)); return (ddi_prop_op(dev, dip, prop_op, flags, name, valuep, lengthp)); } /*ARGSUSED*/ static int pcieb_info(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, void **result) { pcieb_devstate_t *pcieb_p; /* per pcieb state pointer */ minor_t minor = getminor((dev_t)arg); int instance = PCIHP_AP_MINOR_NUM_TO_INSTANCE(minor); pcieb_p = (pcieb_devstate_t *)ddi_get_soft_state(pcieb_state, instance); switch (infocmd) { default: return (DDI_FAILURE); case DDI_INFO_DEVT2INSTANCE: *result = (void *)(intptr_t)instance; return (DDI_SUCCESS); case DDI_INFO_DEVT2DEVINFO: if (pcieb_p == NULL) return (DDI_FAILURE); *result = (void *)pcieb_p->pcieb_dip; return (DDI_SUCCESS); } } /* * Common interrupt handler for hotplug, PME and errors. */ static uint_t pcieb_intr_handler(caddr_t arg1, caddr_t arg2) { pcieb_devstate_t *pcieb_p = (pcieb_devstate_t *)arg1; dev_info_t *dip = pcieb_p->pcieb_dip; ddi_fm_error_t derr; int sts = 0; int ret = DDI_INTR_UNCLAIMED; int isrc; if (!(pcieb_p->pcieb_init_flags & PCIEB_INIT_ENABLE)) goto FAIL; mutex_enter(&pcieb_p->pcieb_intr_mutex); isrc = pcieb_p->pcieb_isr_tab[(int)(uintptr_t)arg2]; mutex_exit(&pcieb_p->pcieb_intr_mutex); PCIEB_DEBUG(DBG_INTR, dip, "Received intr number %d\n", (int)(uintptr_t)arg2); if (isrc == PCIEB_INTR_SRC_UNKNOWN) goto FAIL; if (isrc & PCIEB_INTR_SRC_HP) { if (pcieb_p->pcieb_hpc_type == HPC_PCIE) ret = pciehpc_intr(dip); else if (pcieb_p->pcieb_hpc_type == HPC_SHPC) ret = pcishpc_intr(dip); } if (isrc & PCIEB_INTR_SRC_PME) ret = DDI_INTR_CLAIMED; /* AER Error */ if (isrc & PCIEB_INTR_SRC_AER) { /* * If MSI is shared with PME/hotplug then check Root Error * Status Reg before claiming it. For now it's ok since * we know we get 2 MSIs. */ ret = DDI_INTR_CLAIMED; bzero(&derr, sizeof (ddi_fm_error_t)); derr.fme_version = DDI_FME_VERSION; mutex_enter(&pcieb_p->pcieb_peek_poke_mutex); mutex_enter(&pcieb_p->pcieb_err_mutex); if ((DEVI(dip)->devi_fmhdl->fh_cap) & DDI_FM_EREPORT_CAPABLE) sts = pf_scan_fabric(dip, &derr, NULL); mutex_exit(&pcieb_p->pcieb_err_mutex); mutex_exit(&pcieb_p->pcieb_peek_poke_mutex); if (pcieb_die & sts) fm_panic("%s-%d: PCI(-X) Express Fatal Error. (0x%x)", ddi_driver_name(dip), ddi_get_instance(dip), sts); } FAIL: return (ret); } /* * Some PCI-X to PCI-E bridges do not support full 64-bit addressing on the * PCI-X side of the bridge. We build a special version of this driver for * those bridges, which uses PCIEB_ADDR_LIMIT_LO and/or PCIEB_ADDR_LIMIT_HI * to define the range of values which the chip can handle. The code below * then clamps the DMA address range supplied by the driver, preventing the * PCI-E nexus driver from allocating any memory the bridge can't deal * with. */ static int pcieb_dma_allochdl(dev_info_t *dip, dev_info_t *rdip, ddi_dma_attr_t *attr_p, int (*waitfp)(caddr_t), caddr_t arg, ddi_dma_handle_t *handlep) { int ret; #ifdef BCM_SW_WORKAROUNDS uint64_t lim; /* * If the leaf device's limits are outside than what the Broadcom * bridge can handle, we need to clip the values passed up the chain. */ lim = attr_p->dma_attr_addr_lo; attr_p->dma_attr_addr_lo = MAX(lim, PCIEB_ADDR_LIMIT_LO); lim = attr_p->dma_attr_addr_hi; attr_p->dma_attr_addr_hi = MIN(lim, PCIEB_ADDR_LIMIT_HI); #endif /* BCM_SW_WORKAROUNDS */ /* * This is a software workaround to fix the Broadcom 5714/5715 PCIe-PCI * bridge prefetch bug. Intercept the DMA alloc handle request and set * PX_DMAI_FLAGS_MAP_BUFZONE flag in the handle. If this flag is set, * the px nexus driver will allocate an extra page & make it valid one, * for any DVMA request that comes from any of the Broadcom bridge child * devices. */ if ((ret = ddi_dma_allochdl(dip, rdip, attr_p, waitfp, arg, handlep)) == DDI_SUCCESS) { ddi_dma_impl_t *mp = (ddi_dma_impl_t *)*handlep; #ifdef BCM_SW_WORKAROUNDS mp->dmai_inuse |= PX_DMAI_FLAGS_MAP_BUFZONE; #endif /* BCM_SW_WORKAROUNDS */ /* * For a given rdip, update mp->dmai_bdf with the bdf value * of pcieb's immediate child or secondary bus-id of the * PCIe2PCI bridge. */ mp->dmai_minxfer = pcie_get_bdf_for_dma_xfer(dip, rdip); } return (ret); } /* * FDVMA feature is not supported for any child device of Broadcom 5714/5715 * PCIe-PCI bridge due to prefetch bug. Return failure immediately, so that * these drivers will switch to regular DVMA path. */ /*ARGSUSED*/ static int pcieb_dma_mctl(dev_info_t *dip, dev_info_t *rdip, ddi_dma_handle_t handle, enum ddi_dma_ctlops cmd, off_t *offp, size_t *lenp, caddr_t *objp, uint_t cache_flags) { int ret; #ifdef BCM_SW_WORKAROUNDS if (cmd == DDI_DMA_RESERVE) return (DDI_FAILURE); #endif /* BCM_SW_WORKAROUNDS */ if (((ret = ddi_dma_mctl(dip, rdip, handle, cmd, offp, lenp, objp, cache_flags)) == DDI_SUCCESS) && (cmd == DDI_DMA_RESERVE)) { ddi_dma_impl_t *mp = (ddi_dma_impl_t *)*objp; /* * For a given rdip, update mp->dmai_bdf with the bdf value * of pcieb's immediate child or secondary bus-id of the * PCIe2PCI bridge. */ mp->dmai_minxfer = pcie_get_bdf_for_dma_xfer(dip, rdip); } return (ret); } static int pcieb_intr_ops(dev_info_t *dip, dev_info_t *rdip, ddi_intr_op_t intr_op, ddi_intr_handle_impl_t *hdlp, void *result) { return (pcieb_plat_intr_ops(dip, rdip, intr_op, hdlp, result)); } /*ARGSUSED*/ static int pcieb_pciehpc_probe(dev_info_t *dip, ddi_acc_handle_t config_handle) { uint16_t cap_ptr; if ((PCI_CAP_LOCATE(config_handle, PCI_CAP_ID_PCI_E, &cap_ptr)) != DDI_FAILURE) { uint16_t slotimpl = PCI_CAP_GET16(config_handle, NULL, cap_ptr, PCIE_PCIECAP) & PCIE_PCIECAP_SLOT_IMPL; if (slotimpl) if (PCI_CAP_GET32(config_handle, NULL, cap_ptr, PCIE_SLOTCAP) & PCIE_SLOTCAP_HP_CAPABLE) return (DDI_SUCCESS); } return (DDI_FAILURE); } static int pcieb_pcishpc_probe(dev_info_t *dip, ddi_acc_handle_t config_handle) { return (pcieb_plat_pcishpc_probe(dip, config_handle)); } /* * Initialize hotplug framework if we are hotpluggable. * Sets flag in the soft state if Hot Plug is supported and initialized * properly. */ /*ARGSUSED*/ static int pcieb_init_hotplug(pcieb_devstate_t *pcieb) { int rv = DDI_FAILURE; pcie_bus_t *bus_p = PCIE_DIP2BUS(pcieb->pcieb_dip); ddi_acc_handle_t config_handle = bus_p->bus_cfg_hdl; uint8_t dev_type = bus_p->bus_dev_type; #ifdef PX_PLX uint16_t vid = bus_p->bus_dev_ven_id & 0xFFFF; uint16_t did = bus_p->bus_dev_ven_id >> 16; if ((vid == PXB_VENDOR_PLX) && (did == PXB_DEVICE_PLX_8532) && (bus_p->bus_rev_id <= PXB_DEVICE_PLX_AA_REV)) return (DDI_SUCCESS); #endif /* PX_PLX */ if (((dev_type == PCIE_PCIECAP_DEV_TYPE_DOWN) || (dev_type == PCIE_PCIECAP_DEV_TYPE_PCI2PCIE) || (dev_type == PCIE_PCIECAP_DEV_TYPE_ROOT)) && (pcieb_pciehpc_probe(pcieb->pcieb_dip, config_handle) == DDI_SUCCESS)) { pcieb->pcieb_hpc_type = HPC_PCIE; } else if ((dev_type == PCIE_PCIECAP_DEV_TYPE_PCIE2PCI) && (pcieb_pcishpc_probe(pcieb->pcieb_dip, config_handle) == DDI_SUCCESS)) { pcieb->pcieb_hpc_type = HPC_SHPC; } else { pcieb->pcieb_hpc_type = HPC_NONE; return (DDI_SUCCESS); } pcieb->pcieb_hotplug_capable = B_TRUE; if (pcieb->pcieb_hpc_type == HPC_PCIE) rv = pciehpc_init(pcieb->pcieb_dip, NULL); else if (pcieb->pcieb_hpc_type == HPC_SHPC) rv = pcishpc_init(pcieb->pcieb_dip); if (rv != DDI_SUCCESS) goto fail; if (pcihp_init(pcieb->pcieb_dip) != DDI_SUCCESS) { if (pcieb->pcieb_hpc_type == HPC_PCIE) (void) pciehpc_uninit(pcieb->pcieb_dip); else if (pcieb->pcieb_hpc_type == HPC_SHPC) (void) pcishpc_uninit(pcieb->pcieb_dip); goto fail; } (void) ndi_prop_create_boolean(DDI_DEV_T_NONE, pcieb->pcieb_dip, "hotplug-capable"); return (DDI_SUCCESS); fail: pcieb->pcieb_hpc_type = HPC_NONE; pcieb->pcieb_hotplug_capable = B_FALSE; PCIEB_DEBUG(DBG_ATTACH, pcieb->pcieb_dip, "Failed setting hotplug" " framework\n"); return (DDI_FAILURE); } /* * Power management related initialization specific to pcieb. * Called by pcieb_attach() */ static int pcieb_pwr_setup(dev_info_t *dip) { char *comp_array[5]; int i; ddi_acc_handle_t conf_hdl; uint16_t pmcap, cap_ptr; pcie_pwr_t *pwr_p; /* Some platforms/devices may choose to disable PM */ if (pcieb_plat_pwr_disable(dip)) { (void) pcieb_pwr_disable(dip); return (DDI_SUCCESS); } ASSERT(PCIE_PMINFO(dip)); pwr_p = PCIE_NEXUS_PMINFO(dip); ASSERT(pwr_p); /* Code taken from pci_pci driver */ if (pci_config_setup(dip, &pwr_p->pwr_conf_hdl) != DDI_SUCCESS) { PCIEB_DEBUG(DBG_PWR, dip, "pcieb_pwr_setup: pci_config_setup " "failed\n"); return (DDI_FAILURE); } conf_hdl = pwr_p->pwr_conf_hdl; /* * Walk the capabilities searching for a PM entry. */ if ((PCI_CAP_LOCATE(conf_hdl, PCI_CAP_ID_PM, &cap_ptr)) == DDI_FAILURE) { PCIEB_DEBUG(DBG_PWR, dip, "switch/bridge does not support PM. " " PCI PM data structure not found in config header\n"); pci_config_teardown(&conf_hdl); return (DDI_SUCCESS); } /* * Save offset to pmcsr for future references. */ pwr_p->pwr_pmcsr_offset = cap_ptr + PCI_PMCSR; pmcap = PCI_CAP_GET16(conf_hdl, NULL, cap_ptr, PCI_PMCAP); if (pmcap & PCI_PMCAP_D1) { PCIEB_DEBUG(DBG_PWR, dip, "D1 state supported\n"); pwr_p->pwr_pmcaps |= PCIE_SUPPORTS_D1; } if (pmcap & PCI_PMCAP_D2) { PCIEB_DEBUG(DBG_PWR, dip, "D2 state supported\n"); pwr_p->pwr_pmcaps |= PCIE_SUPPORTS_D2; } i = 0; comp_array[i++] = "NAME=PCIe switch/bridge PM"; comp_array[i++] = "0=Power Off (D3)"; if (pwr_p->pwr_pmcaps & PCIE_SUPPORTS_D2) comp_array[i++] = "1=D2"; if (pwr_p->pwr_pmcaps & PCIE_SUPPORTS_D1) comp_array[i++] = "2=D1"; comp_array[i++] = "3=Full Power D0"; /* * Create pm-components property, if it does not exist already. */ if (ddi_prop_update_string_array(DDI_DEV_T_NONE, dip, "pm-components", comp_array, i) != DDI_PROP_SUCCESS) { PCIEB_DEBUG(DBG_PWR, dip, "could not create pm-components " " prop\n"); pci_config_teardown(&conf_hdl); return (DDI_FAILURE); } return (pcieb_pwr_init_and_raise(dip, pwr_p)); } /* * undo whatever is done in pcieb_pwr_setup. called by pcieb_detach() */ static void pcieb_pwr_teardown(dev_info_t *dip) { pcie_pwr_t *pwr_p; if (!PCIE_PMINFO(dip) || !(pwr_p = PCIE_NEXUS_PMINFO(dip))) return; (void) ddi_prop_remove(DDI_DEV_T_NONE, dip, "pm-components"); if (pwr_p->pwr_conf_hdl) pci_config_teardown(&pwr_p->pwr_conf_hdl); } /* * Initializes the power level and raise the power to D0, if it is * not at D0. */ static int pcieb_pwr_init_and_raise(dev_info_t *dip, pcie_pwr_t *pwr_p) { uint16_t pmcsr; int ret = DDI_SUCCESS; /* * Intialize our power level from PMCSR. The common code initializes * this to UNKNOWN. There is no guarantee that we will be at full * power at attach. If we are not at D0, raise the power. */ pmcsr = pci_config_get16(pwr_p->pwr_conf_hdl, pwr_p->pwr_pmcsr_offset); pmcsr &= PCI_PMCSR_STATE_MASK; switch (pmcsr) { case PCI_PMCSR_D0: pwr_p->pwr_func_lvl = PM_LEVEL_D0; break; case PCI_PMCSR_D1: pwr_p->pwr_func_lvl = PM_LEVEL_D1; break; case PCI_PMCSR_D2: pwr_p->pwr_func_lvl = PM_LEVEL_D2; break; case PCI_PMCSR_D3HOT: pwr_p->pwr_func_lvl = PM_LEVEL_D3; break; default: break; } /* Raise the power to D0. */ if (pwr_p->pwr_func_lvl != PM_LEVEL_D0 && ((ret = pm_raise_power(dip, 0, PM_LEVEL_D0)) != DDI_SUCCESS)) { /* * Read PMCSR again. If it is at D0, ignore the return * value from pm_raise_power. */ pmcsr = pci_config_get16(pwr_p->pwr_conf_hdl, pwr_p->pwr_pmcsr_offset); if ((pmcsr & PCI_PMCSR_STATE_MASK) == PCI_PMCSR_D0) ret = DDI_SUCCESS; else { PCIEB_DEBUG(DBG_PWR, dip, "pcieb_pwr_setup: could not " "raise power to D0 \n"); } } if (ret == DDI_SUCCESS) pwr_p->pwr_func_lvl = PM_LEVEL_D0; return (ret); } /* * Disable PM for x86 and PLX 8532 switch. * For PLX Transitioning one port on this switch to low power causes links * on other ports on the same station to die. Due to PLX erratum #34, we * can't allow the downstream device go to non-D0 state. */ static int pcieb_pwr_disable(dev_info_t *dip) { pcie_pwr_t *pwr_p; ASSERT(PCIE_PMINFO(dip)); pwr_p = PCIE_NEXUS_PMINFO(dip); ASSERT(pwr_p); PCIEB_DEBUG(DBG_PWR, dip, "pcieb_pwr_disable: disabling PM\n"); pwr_p->pwr_func_lvl = PM_LEVEL_D0; pwr_p->pwr_flags = PCIE_NO_CHILD_PM; return (DDI_SUCCESS); } #ifdef DEBUG int pcieb_dbg_intr_print = 0; void pcieb_dbg(uint_t bit, dev_info_t *dip, char *fmt, ...) { va_list ap; if (!pcieb_dbg_print) return; if (dip) prom_printf("%s(%d): %s", ddi_driver_name(dip), ddi_get_instance(dip), pcieb_debug_sym[bit]); va_start(ap, fmt); if (servicing_interrupt()) { if (pcieb_dbg_intr_print) prom_vprintf(fmt, ap); } else { prom_vprintf(fmt, ap); } va_end(ap); } #endif static void pcieb_id_props(pcieb_devstate_t *pcieb) { uint64_t serialid = 0; /* 40b field of EUI-64 serial no. register */ uint16_t cap_ptr; uint8_t fic = 0; /* 1 = first in chassis device */ pcie_bus_t *bus_p = PCIE_DIP2BUS(pcieb->pcieb_dip); ddi_acc_handle_t config_handle = bus_p->bus_cfg_hdl; /* * Identify first in chassis. In the special case of a Sun branded * PLX device, it obviously is first in chassis. Otherwise, in the * general case, look for an Expansion Slot Register and check its * first-in-chassis bit. */ #ifdef PX_PLX uint16_t vendor_id = bus_p->bus_dev_ven_id & 0xFFFF; uint16_t device_id = bus_p->bus_dev_ven_id >> 16; if ((vendor_id == PXB_VENDOR_SUN) && ((device_id == PXB_DEVICE_PLX_PCIX) || (device_id == PXB_DEVICE_PLX_PCIE))) { fic = 1; } #endif /* PX_PLX */ if ((fic == 0) && ((PCI_CAP_LOCATE(config_handle, PCI_CAP_ID_SLOT_ID, &cap_ptr)) != DDI_FAILURE)) { uint8_t esr = PCI_CAP_GET8(config_handle, NULL, cap_ptr, PCI_CAP_ID_REGS_OFF); if (PCI_CAPSLOT_FIC(esr)) fic = 1; } if ((PCI_CAP_LOCATE(config_handle, PCI_CAP_XCFG_SPC(PCIE_EXT_CAP_ID_SER), &cap_ptr)) != DDI_FAILURE) { /* Serialid can be 0 thru a full 40b number */ serialid = PCI_XCAP_GET32(config_handle, NULL, cap_ptr, PCIE_SER_SID_UPPER_DW); serialid <<= 32; serialid |= PCI_XCAP_GET32(config_handle, NULL, cap_ptr, PCIE_SER_SID_LOWER_DW); } if (fic) (void) ndi_prop_create_boolean(DDI_DEV_T_NONE, pcieb->pcieb_dip, "first-in-chassis"); if (serialid) (void) ddi_prop_update_int64(DDI_DEV_T_NONE, pcieb->pcieb_dip, "serialid#", serialid); } static void pcieb_create_ranges_prop(dev_info_t *dip, ddi_acc_handle_t config_handle) { uint32_t base, limit; pcieb_ranges_t ranges[PCIEB_RANGE_LEN]; uint8_t io_base_lo, io_limit_lo; uint16_t io_base_hi, io_limit_hi, mem_base, mem_limit; int i = 0, rangelen = sizeof (pcieb_ranges_t)/sizeof (int); io_base_lo = pci_config_get8(config_handle, PCI_BCNF_IO_BASE_LOW); io_limit_lo = pci_config_get8(config_handle, PCI_BCNF_IO_LIMIT_LOW); io_base_hi = pci_config_get16(config_handle, PCI_BCNF_IO_BASE_HI); io_limit_hi = pci_config_get16(config_handle, PCI_BCNF_IO_LIMIT_HI); mem_base = pci_config_get16(config_handle, PCI_BCNF_MEM_BASE); mem_limit = pci_config_get16(config_handle, PCI_BCNF_MEM_LIMIT); /* * Create ranges for IO space */ ranges[i].size_low = ranges[i].size_high = 0; ranges[i].parent_mid = ranges[i].child_mid = ranges[i].parent_high = 0; ranges[i].child_high = ranges[i].parent_high |= (PCI_REG_REL_M | PCI_ADDR_IO); base = PCIEB_16bit_IOADDR(io_base_lo); limit = PCIEB_16bit_IOADDR(io_limit_lo); if ((io_base_lo & 0xf) == PCIEB_32BIT_IO) { base = PCIEB_LADDR(base, io_base_hi); } if ((io_limit_lo & 0xf) == PCIEB_32BIT_IO) { limit = PCIEB_LADDR(limit, io_limit_hi); } if ((io_base_lo & PCIEB_32BIT_IO) && (io_limit_hi > 0)) { base = PCIEB_LADDR(base, io_base_hi); limit = PCIEB_LADDR(limit, io_limit_hi); } /* * Create ranges for 32bit memory space */ base = PCIEB_32bit_MEMADDR(mem_base); limit = PCIEB_32bit_MEMADDR(mem_limit); ranges[i].size_low = ranges[i].size_high = 0; ranges[i].parent_mid = ranges[i].child_mid = ranges[i].parent_high = 0; ranges[i].child_high = ranges[i].parent_high |= (PCI_REG_REL_M | PCI_ADDR_MEM32); ranges[i].child_low = ranges[i].parent_low = base; if (limit >= base) { ranges[i].size_low = limit - base + PCIEB_MEMGRAIN; i++; } if (i) { (void) ndi_prop_update_int_array(DDI_DEV_T_NONE, dip, "ranges", (int *)ranges, i * rangelen); } } /* * For PCI and PCI-X devices including PCIe2PCI bridge, initialize * cache-line-size and latency timer configuration registers. */ void pcieb_set_pci_perf_parameters(dev_info_t *dip, ddi_acc_handle_t cfg_hdl) { uint_t n; /* Initialize cache-line-size configuration register if needed */ if (ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_DONTPASS, "cache-line-size", 0) == 0) { pci_config_put8(cfg_hdl, PCI_CONF_CACHE_LINESZ, PCIEB_CACHE_LINE_SIZE); n = pci_config_get8(cfg_hdl, PCI_CONF_CACHE_LINESZ); if (n != 0) { (void) ndi_prop_update_int(DDI_DEV_T_NONE, dip, "cache-line-size", n); } } /* Initialize latency timer configuration registers if needed */ if (ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_DONTPASS, "latency-timer", 0) == 0) { uchar_t min_gnt, latency_timer; uchar_t header_type; /* Determine the configuration header type */ header_type = pci_config_get8(cfg_hdl, PCI_CONF_HEADER); if ((header_type & PCI_HEADER_TYPE_M) == PCI_HEADER_ONE) { latency_timer = PCIEB_LATENCY_TIMER; pci_config_put8(cfg_hdl, PCI_BCNF_LATENCY_TIMER, latency_timer); } else { min_gnt = pci_config_get8(cfg_hdl, PCI_CONF_MIN_G); latency_timer = min_gnt * 8; } pci_config_put8(cfg_hdl, PCI_CONF_LATENCY_TIMER, latency_timer); n = pci_config_get8(cfg_hdl, PCI_CONF_LATENCY_TIMER); if (n != 0) { (void) ndi_prop_update_int(DDI_DEV_T_NONE, dip, "latency-timer", n); } } }