/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2006 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #ifndef _SYS_NXGE_NXGE_COMMON_H #define _SYS_NXGE_NXGE_COMMON_H #pragma ident "%Z%%M% %I% %E% SMI" #ifdef __cplusplus extern "C" { #endif #define NXGE_DMA_START B_TRUE #define NXGE_DMA_STOP B_FALSE /* * Default DMA configurations. */ #define NXGE_RDMA_PER_NIU_PORT (NXGE_MAX_RDCS/NXGE_PORTS_NIU) #define NXGE_TDMA_PER_NIU_PORT (NXGE_MAX_TDCS_NIU/NXGE_PORTS_NIU) #define NXGE_RDMA_PER_NEP_PORT (NXGE_MAX_RDCS/NXGE_PORTS_NEPTUNE) #define NXGE_TDMA_PER_NEP_PORT (NXGE_MAX_TDCS/NXGE_PORTS_NEPTUNE) #define NXGE_RDCGRP_PER_NIU_PORT (NXGE_MAX_RDC_GROUPS/NXGE_PORTS_NIU) #define NXGE_RDCGRP_PER_NEP_PORT (NXGE_MAX_RDC_GROUPS/NXGE_PORTS_NEPTUNE) #define NXGE_TIMER_RESO 2 #define NXGE_TIMER_LDG 2 /* * Receive and Transmit DMA definitions */ #if defined(sun4v) && defined(NIU_LP_WORKAROUND) /* * N2/NIU: Maximum descriptors if we need to call * Hypervisor to set up the logical pages * and the driver must use contiguous memory. */ #define NXGE_NIU_MAX_ENTRY (1 << 9) /* 512 */ #define NXGE_NIU_CONTIG_RBR_MAX (NXGE_NIU_MAX_ENTRY) #define NXGE_NIU_CONTIG_RCR_MAX (NXGE_NIU_MAX_ENTRY) #define NXGE_NIU_CONTIG_TX_MAX (NXGE_NIU_MAX_ENTRY) #endif #ifdef _DMA_USES_VIRTADDR #ifdef NIU_PA_WORKAROUND #define NXGE_DMA_BLOCK (16 * 64 * 4) #else #define NXGE_DMA_BLOCK 1 #endif #else #define NXGE_DMA_BLOCK (64 * 64) #endif #define NXGE_RBR_RBB_MIN (128) #define NXGE_RBR_RBB_MAX (64 * 128 -1) #if defined(sun4v) && defined(NIU_LP_WORKAROUND) #define NXGE_RBR_RBB_DEFAULT 512 #define NXGE_RBR_SPARE 0 #else #define NXGE_RBR_RBB_DEFAULT (64 * 16) /* x86 hello */ #define NXGE_RBR_SPARE 0 #endif #define NXGE_RCR_MIN (NXGE_RBR_RBB_MIN * 2) #if defined(sun4v) && defined(NIU_LP_WORKAROUND) #define NXGE_RCR_MAX (NXGE_NIU_CONTIG_RCR_MAX) #define NXGE_RCR_DEFAULT (512) #define NXGE_TX_RING_DEFAULT (512) #else #ifndef NIU_PA_WORKAROUND #define NXGE_RCR_MAX (65355) /* MAX hardware supported */ #if defined(_BIG_ENDIAN) #define NXGE_RCR_DEFAULT (NXGE_RBR_RBB_DEFAULT * 8) #else #ifdef USE_RX_BIG_BUF #define NXGE_RCR_DEFAULT (NXGE_RBR_RBB_DEFAULT * 8) #else #define NXGE_RCR_DEFAULT (NXGE_RBR_RBB_DEFAULT * 4) #endif #endif #define NXGE_TX_RING_DEFAULT (1024) #define NXGE_TX_RING_MAX (64 * 128 - 1) #else #define NXGE_RCR_DEFAULT (512) #define NXGE_TX_RING_DEFAULT (512) #define NXGE_RCR_MAX (1024) #define NXGE_TX_RING_MAX (1024) #endif #endif #define NXGE_TX_RECLAIM 32 /* per receive DMA channel configuration data structure */ typedef struct nxge_rdc_cfg { uint32_t flag; /* 0: not configured, 1: configured */ struct nxge_hw_list *nxge_hw_p; uint32_t partition_id; uint32_t port; /* function number */ uint32_t rx_group_id; /* Partitioning, DMC function zero. */ uint32_t rx_log_page_vld_page0; /* TRUE or FALSE */ uint32_t rx_log_page_vld_page1; /* TRUE or FALSE */ uint64_t rx_log_mask1; uint64_t rx_log_value1; uint64_t rx_log_mask2; uint64_t rx_log_value2; uint64_t rx_log_page_relo1; uint64_t rx_log_page_relo2; uint64_t rx_log_page_hdl; /* WRED parameters, DMC function zero */ uint32_t red_enable; uint32_t thre_syn; uint32_t win_syn; uint32_t threshold; uint32_t win_non_syn; /* RXDMA configuration, DMC */ char *rdc_mbaddr_p; /* mailbox address */ uint32_t min_flag; /* TRUE for 18 bytes header */ /* Software Reserved Packet Buffer Offset, DMC */ uint32_t sw_offset; /* RBR Configuration A */ uint64_t rbr_staddr; /* starting address of RBR */ uint32_t rbr_nblks; /* # of RBR entries */ uint32_t rbr_len; /* # of RBR entries in 64B lines */ /* RBR Configuration B */ uint32_t bksize; /* Block size is fixed. */ #define RBR_BKSIZE_4K 0 #define RBR_BKSIZE_4K_BYTES (4 * 1024) #define RBR_BKSIZE_8K 1 #define RBR_BKSIZE_8K_BYTES (8 * 1024) #define RBR_BKSIZE_16K 2 #define RBR_BKSIZE_16K_BYTES (16 * 1024) #define RBR_BKSIZE_32K 3 #define RBR_BKSIZE_32K_BYTES (32 * 1024) uint32_t bufsz2; #define RBR_BUFSZ2_2K 0 #define RBR_BUFSZ2_2K_BYTES (2 * 1024) #define RBR_BUFSZ2_4K 1 #define RBR_BUFSZ2_4K_BYTES (4 * 1024) #define RBR_BUFSZ2_8K 2 #define RBR_BUFSZ2_8K_BYTES (8 * 1024) #define RBR_BUFSZ2_16K 3 #define RBR_BUFSZ2_16K_BYTES (16 * 1024) uint32_t bufsz1; #define RBR_BUFSZ1_1K 0 #define RBR_BUFSZ1_1K_BYTES 1024 #define RBR_BUFSZ1_2K 1 #define RBR_BUFSZ1_2K_BYTES (2 * 1024) #define RBR_BUFSZ1_4K 2 #define RBR_BUFSZ1_4K_BYTES (4 * 1024) #define RBR_BUFSZ1_8K 3 #define RBR_BUFSZ1_8K_BYTES (8 * 1024) uint32_t bufsz0; #define RBR_BUFSZ0_256B 0 #define RBR_BUFSZ0_256_BYTES 256 #define RBR_BUFSZ0_512B 1 #define RBR_BUFSZ0_512B_BYTES 512 #define RBR_BUFSZ0_1K 2 #define RBR_BUFSZ0_1K_BYTES (1024) #define RBR_BUFSZ0_2K 3 #define RBR_BUFSZ0_2K_BYTES (2 * 1024) /* Receive buffers added by the software */ uint32_t bkadd; /* maximum size is 1 million */ /* Receive Completion Ring Configuration A */ uint32_t rcr_len; /* # of 64B blocks, each RCR is 8B */ uint64_t rcr_staddr; /* Receive Completion Ring Configuration B */ uint32_t pthres; /* packet threshold */ uint32_t entout; /* enable timeout */ uint32_t timeout; /* timeout value */ /* Logical Device Group Number */ uint16_t rx_ldg; uint16_t rx_ld_state_flags; /* Receive DMA Channel Event Mask */ uint64_t rx_dma_ent_mask; /* 32 bit (set to 1) or 64 bit (set to 0) addressing mode */ uint32_t rx_addr_md; } nxge_rdc_cfg_t, *p_nxge_rdc_cfg_t; /* * Per Transmit DMA Channel Configuration Data Structure (32 TDC) */ typedef struct nxge_tdc_cfg { uint32_t flag; /* 0: not configured 1: configured */ struct nxge_hw_list *nxge_hw_p; uint32_t partition_id; uint32_t port; /* function number */ /* partitioning, DMC function zero (All 0s for non-partitioning) */ uint32_t tx_log_page_vld_page0; /* TRUE or FALSE */ uint32_t tx_log_page_vld_page1; /* TRUE or FALSE */ uint64_t tx_log_mask1; uint64_t tx_log_value1; uint64_t tx_log_mask2; uint64_t tx_log_value2; uint64_t tx_log_page_relo1; uint64_t tx_log_page_relo2; uint64_t tx_log_page_hdl; /* Transmit Ring Configuration */ uint64_t tx_staddr; uint64_t tx_rng_len; /* in 64 B Blocks */ #define TX_MAX_BUF_SIZE 4096 /* TXDMA configuration, DMC */ char *tdc_mbaddr_p; /* mailbox address */ /* Logical Device Group Number */ uint16_t tx_ldg; uint16_t tx_ld_state_flags; /* TXDMA event flags */ uint64_t tx_event_mask; /* Transmit threshold before reclamation */ uint32_t tx_rng_threshold; #define TX_RING_THRESHOLD (TX_DEFAULT_MAX_GPS/4) #define TX_RING_JUMBO_THRESHOLD (TX_DEFAULT_JUMBO_MAX_GPS/4) /* For reclaim: a wrap-around counter (packets transmitted) */ uint32_t tx_pkt_cnt; /* last packet with the mark bit set */ uint32_t tx_lastmark; } nxge_tdc_cfg_t, *p_nxge_tdc_cfg_t; #define RDC_TABLE_ENTRY_METHOD_SEQ 0 #define RDC_TABLE_ENTRY_METHOD_REP 1 /* per receive DMA channel table group data structure */ typedef struct nxge_rdc_grp { uint32_t flag; /* 0:not configured 1: configured */ uint8_t port; uint8_t partition_id; uint8_t rx_group_id; uint8_t start_rdc; /* assume assigned in sequence */ uint8_t max_rdcs; uint8_t def_rdc; uint8_t rdc[NXGE_MAX_RDCS]; uint16_t config_method; } nxge_rdc_grp_t, *p_nxge_rdc_grp_t; /* Common RDC and TDC configuration of DMC */ typedef struct _nxge_dma_common_cfg_t { uint16_t rdc_red_ran_init; /* RED initial seed value */ /* Transmit Ring */ } nxge_dma_common_cfg_t, *p_nxge_dma_common_cfg_t; /* * VLAN and MAC table configurations: * Each VLAN ID should belong to at most one RDC group. * Each port could own multiple RDC groups. * Each MAC should belong to one RDC group. */ typedef struct nxge_mv_cfg { uint8_t flag; /* 0:unconfigure 1:configured */ uint8_t rdctbl; /* RDC channel table group */ uint8_t mpr_npr; /* MAC and VLAN preference */ uint8_t odd_parity; } nxge_mv_cfg_t, *p_nxge_mv_cfg_t; typedef struct nxge_param_map { #if defined(_BIG_ENDIAN) uint32_t rsrvd2:2; /* [30:31] rsrvd */ uint32_t remove:1; /* [29] Remove */ uint32_t pref:1; /* [28] preference */ uint32_t rsrv:4; /* [27:24] preference */ uint32_t map_to:8; /* [23:16] map to resource */ uint32_t param_id:16; /* [15:0] Param ID */ #else uint32_t param_id:16; /* [15:0] Param ID */ uint32_t map_to:8; /* [23:16] map to resource */ uint32_t rsrv:4; /* [27:24] preference */ uint32_t pref:1; /* [28] preference */ uint32_t remove:1; /* [29] Remove */ uint32_t rsrvd2:2; /* [30:31] rsrvd */ #endif } nxge_param_map_t, *p_nxge_param_map_t; typedef struct nxge_rcr_param { #if defined(_BIG_ENDIAN) uint32_t rsrvd2:2; /* [30:31] rsrvd */ uint32_t remove:1; /* [29] Remove */ uint32_t rsrv:5; /* [28:24] preference */ uint32_t rdc:8; /* [23:16] rdc # */ uint32_t cfg_val:16; /* [15:0] interrupt parameter */ #else uint32_t cfg_val:16; /* [15:0] interrupt parameter */ uint32_t rdc:8; /* [23:16] rdc # */ uint32_t rsrv:5; /* [28:24] preference */ uint32_t remove:1; /* [29] Remove */ uint32_t rsrvd2:2; /* [30:31] rsrvd */ #endif } nxge_rcr_param_t, *p_nxge_rcr_param_t; /* Needs to have entries in the ndd table */ /* * Hardware properties created by fcode. * In order for those properties visible to the user * command ndd, we need to add the following properties * to the ndd defined parameter array and data structures. * * Use default static configuration for x86. */ typedef struct nxge_hw_pt_cfg { uint32_t partition_id; /* partition Id */ uint32_t read_write_mode; /* read write permission mode */ uint32_t function_number; /* function number */ uint32_t start_tdc; /* start TDC (0 - 31) */ uint32_t max_tdcs; /* max TDC in sequence */ uint32_t start_rdc; /* start RDC (0 - 31) */ uint32_t max_rdcs; /* max rdc in sequence */ uint32_t ninterrupts; /* obp interrupts(mac/mif/syserr) */ uint32_t mac_ldvid; uint32_t mif_ldvid; uint32_t ser_ldvid; uint32_t def_rdc; /* default RDC */ uint32_t drr_wt; /* port DRR weight */ uint32_t rx_full_header; /* select the header flag */ uint32_t start_grpid; /* starting group ID */ uint32_t max_grpids; /* max group ID */ uint32_t start_rdc_grpid; /* starting RDC group ID */ uint32_t max_rdc_grpids; /* max RDC group ID */ uint32_t start_ldg; /* starting logical group # */ uint32_t max_ldgs; /* max logical device group */ uint32_t max_ldvs; /* max logical devices */ uint32_t start_mac_entry; /* where to put the first mac */ uint32_t max_macs; /* the max mac entry allowed */ uint32_t mac_pref; /* preference over VLAN */ uint32_t def_mac_rxdma_grpid; /* default RDC group ID */ uint32_t start_vlan; /* starting VLAN ID */ uint32_t max_vlans; /* max VLAN ID */ uint32_t vlan_pref; /* preference over MAC */ uint32_t def_vlan_rxdma_grpid; /* default RDC group Id */ /* Expand if we have more hardware or default configurations */ uint16_t ldg[NXGE_INT_MAX_LDG]; uint16_t ldg_chn_start; } nxge_hw_pt_cfg_t, *p_nxge_hw_pt_cfg_t; /* per port configuration */ typedef struct nxge_dma_pt_cfg { uint8_t mac_port; /* MAC port (function) */ nxge_hw_pt_cfg_t hw_config; /* hardware configuration */ uint32_t alloc_buf_size; uint32_t rbr_size; uint32_t rcr_size; /* * Configuration for hardware initialization based on the * hardware properties or the default properties. */ uint32_t tx_dma_map; /* Transmit DMA channel bit map */ /* Receive DMA channel */ nxge_rdc_grp_t rdc_grps[NXGE_MAX_RDC_GROUPS]; uint16_t rcr_timeout[NXGE_MAX_RDCS]; uint16_t rcr_threshold[NXGE_MAX_RDCS]; uint8_t rcr_full_header; uint16_t rx_drr_weight; /* Add more stuff later */ } nxge_dma_pt_cfg_t, *p_nxge_dma_pt_cfg_t; /* classification configuration */ typedef struct nxge_class_pt_cfg { /* MAC table */ nxge_mv_cfg_t mac_host_info[NXGE_MAX_MACS]; /* VLAN table */ nxge_mv_cfg_t vlan_tbl[NXGE_MAX_VLANS]; /* class config value */ uint32_t init_h1; uint16_t init_h2; uint8_t mcast_rdcgrp; uint8_t mac_rdcgrp; uint32_t class_cfg[TCAM_CLASS_MAX]; } nxge_class_pt_cfg_t, *p_nxge_class_pt_cfg_t; /* per Neptune sharable resources among ports */ typedef struct nxge_common { uint32_t partition_id; boolean_t mode32; /* DMA Channels: RDC and TDC */ nxge_rdc_cfg_t rdc_config[NXGE_MAX_RDCS]; nxge_tdc_cfg_t tdc_config[NXGE_MAX_TDCS]; nxge_dma_common_cfg_t dma_common_config; uint32_t timer_res; boolean_t ld_sys_error_set; uint8_t sys_error_owner; /* Layer 2/3/4 */ uint16_t class2_etype; uint16_t class3_etype; /* FCRAM (hashing) */ uint32_t hash1_initval; uint32_t hash2_initval; } nxge_common_t, *p_nxge_common_t; /* * Partition (logical domain) configuration per Neptune/NIU. */ typedef struct nxge_part_cfg { uint32_t rdc_grpbits; /* RDC group bit masks */ uint32_t tdc_bitmap; /* bounded TDC */ nxge_dma_pt_cfg_t pt_config[NXGE_MAX_PORTS]; /* Flow Classification Partition (flow partition select register) */ uint8_t hash_lookup; /* external lookup is available */ uint8_t base_mask; /* select bits in base_h1 to replace */ /* bits [19:15} in Hash 1. */ uint8_t base_h1; /* value to replace Hash 1 [19:15]. */ /* Add more here */ uint32_t attributes; /* permission and attribute bits */ #define FZC_SERVICE_ENTITY 0x01 #define FZC_READ_WRITE 0x02 #define FZC_READ_ONLY 0x04 } nxge_part_cfg_t, *p_nxge_part_cfg_t; typedef struct nxge_hw_list { struct nxge_hw_list *next; nxge_os_mutex_t nxge_cfg_lock; nxge_os_mutex_t nxge_tcam_lock; nxge_os_mutex_t nxge_vlan_lock; nxge_os_mutex_t nxge_mdio_lock; nxge_os_mutex_t nxge_mii_lock; nxge_dev_info_t *parent_devp; struct _nxge_t *nxge_p[NXGE_MAX_PORTS]; uint32_t ndevs; uint32_t flags; uint32_t magic; } nxge_hw_list_t, *p_nxge_hw_list_t; #ifdef __cplusplus } #endif #endif /* _SYS_NXGE_NXGE_COMMON_H */