'\" te
.\" Copyright (c) 2008, Sun Microsystems, Inc. All Rights Reserved
.\" The contents of this file are subject to the terms of the Common Development and Distribution License (the "License").  You may not use this file except in compliance with the License.
.\" You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing.  See the License for the specific language governing permissions and limitations under the License.
.\" When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE.  If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
.TH MTIO 7I "Sep 15, 2007"
.SH NAME
mtio \- general magnetic tape interface
.SH SYNOPSIS
.LP
.nf
#include <sys/types.h>
#include <sys/ioctl.h>
#include <sys/mtio.h>
.fi

.SH DESCRIPTION
.sp
.LP
1/2", 1/4", 4mm, and 8mm magnetic tape drives all share the same general
character device interface.
.sp
.LP
There are two types of tape records: data records and end-of-file (EOF)
records. S\fBEOF\fR records are also known as tape marks and file marks. A
record is separated by interrecord (or tape) gaps on a tape.
.sp
.LP
End-of-recorded-media (EOM) is indicated by two \fBEOF\fR marks on 1/2" tape;
by one \fBEOF\fR mark on 1/4", 4mm, and 8mm cartridge tapes.
.SS "1/2" Reel Tape"
.sp
.LP
Data bytes are recorded in parallel onto the 9-track tape. Since it is a
variable-length tape device, the number of bytes in a  physical record may
vary.
.sp
.LP
The recording formats available (check specific tape drive) are 800 \fBBPI,\fR
1600 \fBBPI,\fR 6250 \fBBPI,\fR and data compression. Actual storage capacity
is a function of the recording format and the length of the tape reel. For
example, using a 2400 foot tape, 20 Mbyte can be stored using 800 \fBBPI,\fR 40
Mbyte using 1600 \fBBPI,\fR 140 Mbyte using 6250 \fBBPI,\fR or up to 700 Mbyte
using data compression.
.SS "1/4" Cartridge Tape"
.sp
.LP
Data is recorded serially onto 1/4" cartridge tape. The number of bytes per
record is determined by the physical record size of the device. The I/O request
size must be a multiple of the physical record size of the device. For
\fBQIC-11,\fR \fBQIC-24,\fR and \fBQIC-150\fR tape drives, the block size is
512 bytes.
.sp
.LP
The records are recorded on tracks in a serpentine motion. As one track is
completed, the drive switches to the next and begins writing in the opposite
direction, eliminating the wasted motion of rewinding. Each file, including the
last, ends with one file mark.
.sp
.LP
Storage capacity is based on the number of tracks the drive is capable of
recording. For example, 4-track drives can only record 20 Mbyte of data on a
450 foot tape; 9-track drives can record up to 45 Mbyte of data on a tape of
the same length. \fBQIC-11\fR is the only tape format available for 4-track
tape drives. In contrast, 9-track tape drives can use either \fBQIC-24\fR or
\fBQIC-11.\fR Storage capacity is not appreciably affected by using either
format. \fBQIC-24\fR is preferable to \fBQIC-11\fR because it records a
reference signal to mark the position of the first track on the tape, and each
block has a unique block number.
.sp
.LP
The \fBQIC-150\fR tape drives require \fBDC-6150\fR (or equivalent) tape
cartridges for writing. However, they can read other tape cartridges in
\fBQIC-11,\fR \fBQIC-24,\fR or \fBQIC-120\fR tape formats.
.SS "8mm Cartridge Tape"
.sp
.LP
Data is recorded serially onto 8mm helical scan cartridge tape. Since it is a
variable-length tape device, the number of bytes in a  physical record may
vary. The recording formats available (check specific tape drive) are standard
2Gbyte, 5Gbyte, and compressed format.
.SS "4mm DAT Tape"
.sp
.LP
Data is recorded either in Digital Data Storage (DDS) tape format or in Digital
Data Storage, Data Compressed (DDS-DC) tape format. Since it is a
variable-length tape device, the number of bytes in a  physical record may
vary. The recording formats available are standard 2Gbyte and compressed
format.
.SS "Persistent Error Handling"
.sp
.LP
Persistent error handling is a modification of the current error handling
behaviors, BSD and SVR4. With persistent error handling enabled, all tape
operations after an error or exception will return immediately with an error.
Persistent error handling can be most useful with asynchronous tape operations
that use the \fBaioread\fR(3C) and \fBaiowrite\fR(3C) functions.
.sp
.LP
To enable persistent error handling, the ioctl \fBMTIOCPERSISTENT\fR must be
issued. If this ioctl succeeds, then persistent error handling is enabled and
changes the current error behavior. This ioctl will fail if the device driver
does not support persistent error handling.
.sp
.LP
With persistent error handling enabled, all tape operations after an exception
or error will return with the same error as the first command that failed; the
operations will not be executed. An exception is some event that might stop
normal tape operations, such as an End Of File (EOF) mark or  an End Of Tape
(EOT) mark. An example of an error is a media error. The \fBMTIOCLRERR\fR ioctl
must be issued to allow normal tape operations to continue and to clear the
error.
.sp
.LP
Disabling persistent error handling returns the error behavior to normal SVR4
error handling, and will not occur until all outstanding operations are
completed. Applications should wait for all outstanding operations to complete
before disabling persistent error handling. Closing the device will also
disable persistent error handling and clear any errors or exceptions.
.sp
.LP
The \fBRead Operation\fR and \fBWrite Operation\fR subsections contain more
pertinent information reguarding persistent error handling.
.SS "Read Operation"
.sp
.LP
The \fBread\fR(2) function reads the next record on the tape. The record size
is passed back as the number of bytes read, provided it is not greater than the
number requested. When a tape mark or end of data is read, a zero byte count is
returned; all successive reads after the zero read will return an error and
\fBerrno\fR will be set to \fBEIO\fR. To move to the next file, an \fBMTFSF\fR
ioctl can be issued before or after the read causing the error. This error
handling behavior is different from the older \fBBSD\fR behavior, where another
read will fetch the first record of the next tape file. If the \fBBSD\fR
behavior is required, device names containing the letter \fBb\fR (for \fBBSD\fR
behavior) in the final component should be used. If persistent error handling
was enabled with either the BSD or SVR4 tape device behavior, all operations
after this read error will return \fBEIO\fR errors until the \fBMTIOCLRERR\fR
ioctl is issued. An \fBMTFSF\fR ioctl can then he issued.
.sp
.LP
Two successful successive reads that both return zero byte counts indicate
\fBEOM\fR on the tape. No further reading should be performed past the
\fBEOM.\fR
.sp
.LP
Fixed-length I/O tape devices require the number of bytes read to be a multiple
of the physical record size. For example, 1/4" cartridge tape devices only read
multiples of 512 bytes. If the blocking factor is greater than 64,512 bytes
(minphys limit), fixed-length I/O tape devices read multiple records.
.sp
.LP
Most tape devices which support variable-length I/O operations may read a range
of 1 to 65,535 bytes. If the record size exceeds 65,535 bytes, the driver reads
multiple records to satisfy the request. These multiple records are limited to
65,534 bytes. Newer variable-length tape drivers may relax the above limitation
and allow applications to read record sizes larger than 65,534. Refer to the
specific tape driver man page for details.
.sp
.LP
Reading past logical \fBEOT\fR is transparent to the user. A read operation
should never hit physical EOT.
.sp
.LP
Read requests that are lesser than a physical tape record are not allowed.
Appropriate error is returned.
.SS "Write Operation"
.sp
.LP
The \fBwrite\fR(2) function writes the next record on the tape. The record has
the same length as the given buffer.
.sp
.LP
Writing is allowed on 1/4" tape at either the beginning of tape or after the
last written file on the tape. With the Exabyte 8200, data may be appended only
at the beginning of tape, before a filemark, or after the last written file on
the tape.
.sp
.LP
Writing is not so restricted on 1/2", 4mm, and the other 8mm cartridge tape
drives. Care should be used when appending files onto 1/2" reel tape devices,
since an extra file mark is appended after the last file to mark the \fBEOM.\fR
This extra file mark must be overwritten to prevent the creation of a null
file. To facilitate write append operations, a space to the \fBEOM\fR ioctl is
provided. Care should be taken when overwriting records; the erase head is just
forward of the write head and any following records will also be erased.
.sp
.LP
Fixed-length I/O tape devices require the number of bytes written to be a
multiple of the physical record size. For example, 1/4" cartridge tape devices
only write multiples of 512 bytes.
.sp
.LP
Fixed-length I/O tape devices write multiple records if the blocking factor is
greater than 64,512 bytes (minphys limit). These multiple writes are limited to
64,512 bytes. For example, if a write request is issued for 65,536 bytes using
a 1/4" cartridge tape, two writes are issued; the first for 64,512 bytes and
the second for 1024 bytes.
.sp
.LP
Most tape devices which support variable-length I/O operations may write a
range of 1 to 65,535 bytes. If the record size exceeds 65,535 bytes, the driver
writes multiple records to satisfy the request. These multiple records are
limited to 65,534 bytes. As an example, if a write request for 65,540 bytes is
issued, two records are written; one for 65,534 bytes followed by another
record for 6 bytes. Newer variable-length tape drivers may relax the above
limitation and allow applications to write record sizes larger  than 65,534.
Refer to the specific tape driver man page for details.
.sp
.LP
When logical \fBEOT\fR is encountered during a write, that write operation
completes and the number of bytes successfully transferred is returned (note
that a 'short write' may have occurred and not all the requested bytes would
have been transferred. The actual amount of data written will depend on the
type of device being used). The next write will return a zero byte count. A
third write will successfully transfer some bytes (as indicated by the returned
byte count, which again could be a short write); the fourth will transfer zero
bytes, and so on, until the physical \fBEOT\fR is reached and all writes will
fail with \fBEIO\fR.
.sp
.LP
When logical \fBEOT\fR is encountered with persistent error handling enabled,
the current write may complete or be a short write. The next write will return
a zero byte count. At this point an application should act appropriately for
end of tape cleanup or issue yet another write, which will return the error
\fBENOSPC\fR. After clearing the exception with \fBMTIOCLRERR\fR, the next
write will succeed (possibly short), followed by another zero byte write count,
and then another \fBENOSPC\fR error.
.sp
.LP
Allowing writes after \fBLEOT\fR has been encountered enables the flushing of
buffers. However, it is strongly recommended to terminate the writing and close
the file as soon as possible.
.sp
.LP
Seeks are ignored in tape I/O.
.SS "Close Operation"
.sp
.LP
Magnetic tapes are rewound when closed, except when the "no-rewind" devices
have been specified. The names of no-rewind device files use the letter \fBn\fR
as the end of the final component. The no-rewind version of \fB/dev/rmt/0l\fR
is \fB/dev/rmt/0ln\fR. In case of error for a no-rewind device, the next open
rewinds the device.
.sp
.LP
If the driver was opened for reading and a no-rewind device has been specified,
the close advances the tape past the next filemark (unless the current file
position is at \fBEOM),\fR leaving the tape correctly positioned to read the
first record of the next file. However, if the tape is at the first record of a
file it doesn't advance again to the first record of the next file. These
semantics are different from the older \fBBSD\fR behavior. If \fBBSD\fR
behavior is required where no implicit space operation is executed on close,
the non-rewind device name containing the letter \fBb\fR (for \fBBSD\fR
behavior) in the final component should be specified.
.sp
.LP
If data was written, a file mark is automatically written by the driver upon
close. If the rewinding device was specified, the tape will be rewound after
the file mark is written. If the user wrote a file mark prior to closing, then
no file mark is written upon close. If a file positioning ioctl, like rewind,
is issued after writing, a file mark is written before repositioning the tape.
.sp
.LP
All buffers are flushed on closing a tape device. Hence, it is strongly
recommended that the application wait for all buffers to be flushed before
closing the device. This can be done by writing a filemark via \fBMTWEOF,\fR
even with a zero count.
.sp
.LP
Note that for 1/2" reel tape devices, two file marks are written to mark the
\fBEOM\fR before rewinding or performing a file positioning ioctl. If the user
wrote a file mark before closing a 1/2" reel tape device, the driver will
always write a file mark before closing to insure that the end of recorded
media is marked properly. If the non-rewinding device was specified, two file
marks are written and the tape is left positioned between the two so that the
second one is overwritten on a subsequent \fBopen\fR(2) and \fBwrite\fR(2).
.sp
.LP
If no data was written and the driver was opened for \fBWRITE-ONLY\fR access,
one or two file marks are written, thus creating a null file.
.sp
.LP
After closing the device, persistent error handling will be disabled and any
error or exception will be cleared.
.SH IOCTLS
.sp
.LP
Not all devices support all \fBioctls\fR. The driver returns an \fBENOTTY\fR
error on unsupported ioctls.
.sp
.LP
The following structure definitions for magnetic tape \fBioctl \fRcommands are
from \fB<sys/mtio.h>\fR\&.
.sp
.LP
The minor device byte structure is::
.sp
.in +2
.nf
15      7      6          5          4         3          2       1   0
________________________________________________________________________
Unit #       BSD      Reserved   Density   Density   No rewind    Unit #
Bits 7-15   behavior              Select    Select    on Close    Bits 0-1
.fi
.in -2

.sp
.in +2
.nf
/*
 * Layout of minor device byte:
 */
#define MTUNIT(dev)	(((minor(dev) & 0xff80) >> 5) +
(minor(dev) & 0x3))
#define MT_NOREWIND	(1 <<2)
#define MT_DENSITY_MASK	(3 <<3)
#define MT_DENSITY1	(0 <<3)	/* Lowest density/format */
#define MT_DENSITY2	(1 <<3)
#define MT_DENSITY3	(2 <<3)
#define MT_DENSITY4	(3 <<3)	/* Highest density/format */
#define MTMINOR(unit)	(((unit & 0x7fc) << 5) + (unit & 0x3))
#define MT_BSD	(1 <<6)       /* BSD behavior on close */


/* Structure for MTIOCTOP \(mi magnetic tape operation command */

struct  mtop {
  short   mt_op;       /* operation */
  daddr_t mt_count;    /* number of operations */
};
.fi
.in -2

.sp
.in +2
.nf
/* Structure for MTIOCLTOP - magnetic tape operation command */
Works exactly like MTIOCTOP except passes 64 bit mt_count values.
struct  mtlop    {
        short           mt_op;
        short           pad[3];
        int64_t         mt_count;
};
.fi
.in -2

.sp
.LP
The following operations of \fBMTIOCTOP\fR and \fBMTIOCLTOP\fR ioctls are
supported:
.sp
.ne 2
.na
\fBMTWEOF\fR
.ad
.RS 17n
write an end-of-file record
.RE

.sp
.ne 2
.na
\fBMTFSF\fR
.ad
.RS 17n
forward space over file mark
.RE

.sp
.ne 2
.na
\fBMTBSF\fR
.ad
.RS 17n
backward space over file mark (1/2", 8mm only)
.RE

.sp
.ne 2
.na
\fBMTFSR\fR
.ad
.RS 17n
forward space to inter-record gap
.RE

.sp
.ne 2
.na
\fBMTBSR\fR
.ad
.RS 17n
backward space to inter-record gap
.RE

.sp
.ne 2
.na
\fBMTREW\fR
.ad
.RS 17n
rewind
.RE

.sp
.ne 2
.na
\fBMTOFFL\fR
.ad
.RS 17n
rewind and take the drive off-line
.RE

.sp
.ne 2
.na
\fBMTNOP\fR
.ad
.RS 17n
no operation, sets status only
.RE

.sp
.ne 2
.na
\fBMTRETEN\fR
.ad
.RS 17n
retension the tape (cartridge tape only)
.RE

.sp
.ne 2
.na
\fBMTERASE\fR
.ad
.RS 17n
erase the entire tape and rewind
.RE

.sp
.ne 2
.na
\fBMTEOM\fR
.ad
.RS 17n
position to EOM
.RE

.sp
.ne 2
.na
\fBMTNBSF\fR
.ad
.RS 17n
backward space file to beginning of file
.RE

.sp
.ne 2
.na
\fBMTSRSZ\fR
.ad
.RS 17n
set record size
.RE

.sp
.ne 2
.na
\fBMTGRSZ\fR
.ad
.RS 17n
get record size
.RE

.sp
.ne 2
.na
\fBMTTELL\fR
.ad
.RS 17n
get current position
.RE

.sp
.ne 2
.na
\fBMTSEEK\fR
.ad
.RS 17n
go to  requested  position
.RE

.sp
.ne 2
.na
\fBMTFSSF\fR
.ad
.RS 17n
forward to requested number of sequential file marks
.RE

.sp
.ne 2
.na
\fBMTBSSF\fR
.ad
.RS 17n
backward to requested number of sequential file marks
.RE

.sp
.ne 2
.na
\fBMTLOCK\fR
.ad
.RS 17n
prevent media removal
.RE

.sp
.ne 2
.na
\fBMTUNLOCK\fR
.ad
.RS 17n
allow media removal
.RE

.sp
.ne 2
.na
\fBMTLOAD\fR
.ad
.RS 17n
load the next tape cartridge into the tape drive
.RE

.sp
.ne 2
.na
\fBMTIOCGETERROR\fR
.ad
.RS 17n
retrieve error records from the st driver
.RE

.sp
.in +2
.nf
/* structure for MTIOCGET \(mi magnetic tape get status command */

struct  mtget {
  short	mt_type;	/* type of magtape device */
/* the following two registers are device dependent */
  short  mt_dsreg;      /* "drive status" register */
  short  mt_erreg;      /* "error" register */
/* optional error info. */
  daddr_t   mt_resid;   /* residual count */
  daddr_t   mt_fileno;  /* file number of current position */
  daddr_t   mt_blkno;   /* block number of current position */
  ushort_t  mt_flags;
  short     mt_bf;      /* optimum blocking factor */
};
/* structure for MTIOCGETDRIVETYPE \(mi get tape config data command */
struct mtdrivetype_request {
  int  size;
  struct  mtdrivetype	*mtdtp;
};
struct mtdrivetype {
  char    name[64];                  /* Name, for debug */
  char    vid[25];                   /* Vendor id and product id */
  char    type;                      /* Drive type for driver */
  int     bsize;                     /* Block size */
  int     options;                   /* Drive options */
  int     max_rretries;              /* Max read retries */
  int     max_wretries;              /* Max write retries */
  uchar_t densities[MT_NDENSITIES];  /* density codes,low->hi */
  uchar_t default_density;           /* Default density chosen */
  uchar_t speeds[MT_NSPEEDS];        /* speed codes, low->hi */
  ushort_t non_motion_timeout;       /* Seconds for non-motion */
  ushort_t io_timeout;               /* Seconds for data to from tape */
  ushort_t rewind_timeout;           /* Seconds to rewind */
  ushort_t space_timeout;            /* Seconds to space anywhere */
  ushort_t load_timeout;             /* Seconds to load tape and ready */
  ushort_t unload_timeout;           /* Seconds to unload */
  ushort_t erase_timeout;            /* Seconds to do long erase */
};
.fi
.in -2

.sp
.in +2
.nf
/* structure for MTIOCGETPOS and MTIOCRESTPOS - get/set tape position */
 	/*
  * eof/eot/eom codes.
 	 */
 typedef enum {
       ST_NO_EOF,
       ST_EOF_PENDING,         /* filemrk pending */
       ST_EOF,                 /* at filemark */
       ST_EOT_PENDING,         /* logical eot pend. */
       ST_EOT,                 /* at logical eot */
       ST_EOM,                 /* at physical eot */
       ST_WRITE_AFTER_EOM      /* flag allowing writes after EOM */
 	}pstatus;

 	typedef enum { invalid, legacy, logical } posmode;

 	typedef struct tapepos {
 		   uint64_t lgclblkno;	/* Blks from start of partition */
 		   int32_t fileno;		/* Num. of current file */
 		   int32_t blkno;		/* Blk  number in current file */
 		   int32_t partition; 	/* Current partition */
 		   pstatus eof;         /* eof states */
 		   posmode pmode;		 /* which pos. data is valid */
 		   char    pad[4];
 	}tapepos_t;

     If the pmode is legacy,fileno and blkno fields are valid.
     If the pmode is logical, lgclblkno field is valid.
.fi
.in -2

.sp
.LP
The \fBMTWEOF\fR ioctl is used for writing file marks to tape. Not only does
this signify the end of a file, but also usually has the side effect of
flushing all buffers in the tape drive to the tape medium. A zero count
\fBMTWEOF\fR will just flush all the buffers and will not write any file marks.
Because a successful completion of this tape operation will guarantee that all
tape data has been written to the tape medium, it is recommended that this tape
operation be issued before closing a tape device.
.sp
.LP
When spacing forward over a record (either data or \fBEOF),\fR the tape head is
positioned in the tape gap between the record just skipped and the next record.
When spacing forward over file marks (EOF records), the tape head is positioned
in the tape gap between the next \fBEOF\fR record and the record that follows
it.
.sp
.LP
When spacing backward over a record (either data or \fBEOF),\fR the tape head
is positioned in the tape gap immediately preceding the tape record where the
tape head is currently positioned. When spacing backward over file marks (EOF
records), the tape head is positioned in the tape gap preceding the \fBEOF.\fR
Thus the next read would fetch the \fBEOF.\fR
.sp
.LP
Record skipping does not go past a file mark; file skipping does not go past
the \fBEOM.\fR After an \fBMTFSR\fR <huge number> command, the driver leaves
the tape logically positioned \fIbefore\fR the \fBEOF.\fR A related feature is
that \fBEOFs\fR remain pending until the tape is closed. For example, a program
which first reads all the records of a file up to and including the \fBEOF\fR
and then performs an \fBMTFSF\fR command will leave the tape positioned just
after that same \fBEOF,\fR rather than skipping the next file.
.sp
.LP
The \fBMTNBSF\fR and \fBMTFSF\fR operations are inverses. Thus, an "
\fBMTFSF\fR \(mi1" is equivalent to an " \fBMTNBSF\fR 1". An " \fBMTNBSF\fR 0"
is the same as " \fBMTFSF\fR 0"; both position the tape device at the beginning
of the current file.
.sp
.LP
\fBMTBSF\fR moves the tape backwards by file marks. The tape position will end
on the beginning of the tape side of the desired file mark. An " \fBMTBSF\fR 0"
will position the tape at the end of the current file, before the filemark.
.sp
.LP
\fBMTBSR\fR and \fBMTFSR\fR operations perform much like space file operations,
except that they move by records instead of files. Variable-length I/O devices
(1/2" reel, for example) space actual records; fixed-length I/O devices space
physical records (blocks). 1/4" cartridge tape, for example, spaces 512 byte
physical records. The status ioctl residual count contains the number of files
or records not skipped.
.sp
.LP
MTFSSF and MTBSSF space forward or backward, respectively, to the next
occurrence of the requested number of file marks, one following another. If
there are more sequential file marks on tape than were requested, it spaces
over the requested number and positions after the requested file mark. Note
that not all drives support this command and if a request is sent to a drive
that does not, \fBENOTTY\fR is returned.
.sp
.LP
\fBMTOFFL\fR rewinds and, if appropriate, takes the device off-line by
unloading the tape. It is recommended that the device be closed after offlining
and then re-opened after a tape has been inserted to facilitate portability to
other platforms and other operating systems. Attempting to re-open the device
with no tape will result in an error unless the \fBO_NDELAY\fR flag is used.
(See \fBopen\fR(2).)
.sp
.LP
The \fBMTRETEN\fR retension ioctl applies only to 1/4" cartridge tape devices.
It is used to restore tape tension, improving the tape's soft error rate after
extensive start-stop operations or long-term storage.
.sp
.LP
\fBMTERASE\fR rewinds the tape, erases it completely, and returns to the
beginning of tape. Erasing may take a long time depending on the device and/or
tapes.  For time details, refer to the the drive specific manual.
.sp
.LP
\fBMTEOM\fR positions the tape at a location just after the last file written
on the tape. For 1/4" cartridge and 8mm tape, this is after the last file mark
on the tape. For 1/2" reel tape, this is just after the first file mark but
before the second (and last) file mark on the tape. Additional files can then
be appended onto the tape from that point.
.sp
.LP
Note the difference between \fBMTBSF\fR (backspace over file mark) and
\fBMTNBSF\fR (backspace file to beginning of file). The former moves the tape
backward until it crosses an \fBEOF\fR mark, leaving the tape positioned
\fIbefore\fR the file mark. The latter leaves the tape positioned \fIafter\fR
the file mark. Hence, "\fBMTNBSF\fR n" is equivalent to "\fBMTBSF\fR (n+1)"
followed by "\fBMTFSF\fR 1". The 1/4" cartridge tape devices do not support
\fBMTBSF.\fR
.sp
.LP
\fBMTSRSZ\fR and \fBMTGRSZ\fR are used to set and get fixed record lengths. The
\fBMTSRSZ\fR ioctl allows variable length and fixed length tape drives that
support multiple record sizes to set the record length. The \fBmt_count\fR
field of the  \fBmtop\fR struct is used to pass the record size to/from the
\fBst\fR driver. A value of \fB0\fR indicates variable record size. The
\fBMTSRSZ\fR ioctl makes a variable-length tape device behave like a
fixed-length tape device. Refer to the specific tape driver man page for
details.
.sp
.LP
\fBMTLOAD\fR loads the next tape cartridge into the tape drive. This is
generally only used with stacker and tower type tape drives which handle
multiple tapes per tape drive. A tape device without a tape inserted can be
opened with the \fBO_NDELAY\fR flag, in order to execute this operation.
.sp
.LP
\fBMTIOCGETERROR\fR allows user-level applications to retrieve error records
from the \fBst\fR driver. An error record consists of the SCSI command cdb
which causes the error and a \fBscsi_arq_status\fR(9S) structure if available.
The user-level application is responsible for allocating and releasing the
memory for mtee_cdb_buf and scsi_arq_status of each mterror_entry. Before
issuing the ioctl, the mtee_arq_status_len value should be at least equal to
"sizeof(struct scsi_arq_status)." If more sense data than the size of
\fBscsi_arq_status\fR(9S) is desired, the mtee_arq_status_len may be larger
than "sizeof(struct scsi_arq_status)" by the amount of additional extended
sense data desired.  The es_add_len field of \fBscsi_extended_sense\fR(9S) can
be used to determine the amount of valid sense data returned by the device.
.sp
.LP
The \fBMTIOCGET\fR get status \fBioctl\fR call returns the drive ID
(\fImt_type\fR), sense key error (\fImt_erreg\fR), file  number
(\fImt_fileno\fR), optimum blocking factor (\fImt_bf\fR) and record number
(\fImt_blkno\fR) of the last error. The residual count (\fImt_resid\fR) is set
to the number of bytes not transferred or files/records not spaced. The flags
word (\fImt_flags\fR) contains information indicating if the device is SCSI, if
the device is a reel device and whether the device supports absolute file
positioning. The \fImt_flags\fR also indicates if the device is requesting
cleaning media be used, whether the device is capable of reporting the
requirement of cleaning media and if the currently loaded media is WORM (Write
Once Read Many) media.
.LP
Note -
.sp
.RS 2
When tape alert cleaning is managed by the st driver, the tape target driver
may continue to return a "drive needs cleaning" status unless an MTIOCGET
ioctl() call is made while the cleaning media is in the drive.
.RE
.sp
.LP
The  \fBMTIOCGETDRIVETYPE\fR get drivetype ioctl call returns the name of the
tape drive as defined in  \fBst.conf\fR (\fIname\fR), Vendor \fBID\fR and model
(\fIproduct\fR), \fBID\fR (\fIvid\fR), type of tape device (\fBtype\fR), block
size  (\fIbsize\fR), drive options  (\fIoptions\fR), maximum read retry count
(\fImax_rretries\fR), maximum write retry count (\fImax_wretries\fR), densities
supported by the drive (\fIdensities\fR), and default density of the tape drive
(\fIdefault_density\fR).
.sp
.LP
The MTIOCGETPOS ioctl returns the current tape position of the drive. It is
returned in struct tapepos as defined in
\fB/usr/include/sys/scsi/targets/stdef.h\fR.
.sp
.LP
The  MTIOCRESTPOS ioctl restores a saved position from the MTIOCGETPOS.
.SS "Persistent Error Handling IOCTLs and Asynchronous Tape Operations"
.sp
.ne 2
.na
\fBMTIOCPERSISTENT\fR
.ad
.RS 25n
enables/disables persistent error handling
.RE

.sp
.ne 2
.na
\fBMTIOCPERSISTENTSTATUS\fR
.ad
.RS 25n
queries for persistent error handling
.RE

.sp
.ne 2
.na
\fBMTIOCLRERR\fR
.ad
.RS 25n
clears persistent error handling
.RE

.sp
.ne 2
.na
\fBMTIOCGUARANTEEDORDER\fR
.ad
.RS 25n
checks whether driver guarantees order of I/O's
.RE

.sp
.LP
The \fBMTIOCPERSISTENT\fR ioctl enables or disables persistent error handling.
It takes as an argument a pointer to an integer that turns it either on or off.
If the ioctl succeeds, the desired operation was successful. It will wait for
all outstanding I/O's to complete before changing the persistent error handling
status. For example,
.sp
.in +2
.nf
int on = 1;
ioctl(fd, MTIOCPERSISTENT, &on);
int off = 0;
ioctl(fd, MTIOCPERSISTENT, &off);
.fi
.in -2

.sp
.LP
The \fBMTIOCPERSISTENTSTATUS\fR ioctl enables or disables persistent error
handling. It takes as an argument a pointer to an integer inserted by the
driver. The integer can be either 1 if persistent error handling is 'on', or 0
if persistent error handling is 'off'. It will not wait for outstanding I/O's.
For example,
.sp
.in +2
.nf
int query;
ioctl(fd, MTIOCPERSISTENTSTATUS, &query);
.fi
.in -2

.sp
.LP
The \fBMTIOCLRERR\fR ioctl clears persistent error handling and allows tape
operations to continual normally. This ioctl requires no argument and will
always succeed, even if persistent error handling has not been enabled. It will
wait for any outstanding I/O's before it clears the error.
.sp
.LP
The \fBMTIOCGUARANTEEDORDER\fR ioctl is used to determine whether the driver
guarantees the order of I/O's. It takes no argument. If the ioctl succeeds, the
driver will support guaranteed order. If the driver does not support guaranteed
order, then it should not be used for asynchronous I/O with \fBlibaio\fR. It
will wait for any outstanding I/O's before it returns. For example,
.sp
.in +2
.nf
ioctl(fd, MTIOCGUARANTEEDORDER)
.fi
.in -2

.sp
.LP
See the \fBPersistent Error Handling\fR subsection above for more information
on persistent error handling.
.SS "Asynchronous and State Change IOCTLS"
.sp
.ne 2
.na
\fB\fBMTIOCSTATE\fR\fR
.ad
.RS 14n
This ioctl blocks until the state of the drive, inserted or ejected, is
changed. The argument is a pointer to a \fBmtio_state\fR, \fBenum\fR, whose
possible enumerations are listed below. The initial value should be either the
last reported state of the drive, or \fBMTIO_NONE\fR. Upon return, the
\fBenum\fR pointed to by the argument is updated with the current state of the
drive.
.RE

.sp
.in +2
.nf
enum mtio_state {
MTIO_NONE      /* Return tape's current state */
MTIO_EJECTED   /* Tape state is "ejected" */
MTIO_INSERTED  /* Tape state is "inserted" */
;
.fi
.in -2

.sp
.LP
When using asynchronous operations, most ioctls will wait for all outstanding
commands to complete before they are executed.
.SS "IOCTLS for Multi-initiator Configurations"
.sp
.ne 2
.na
\fBMTIOCRESERVE\fR
.ad
.RS 21n
reserve the tape drive
.RE

.sp
.ne 2
.na
\fBMTIOCRELEASE\fR
.ad
.RS 21n
revert back to the default behavior of reserve on open/release on close
.RE

.sp
.ne 2
.na
\fBMTIOCFORCERESERVE\fR
.ad
.RS 21n
reserve the tape unit by breaking reservation held by another host
.RE

.sp
.LP
The \fBMTIOCRESERVE\fR ioctl reserves the tape drive such that it does not
release the tape drive at close. This changes the default behavior of releasing
the device upon close. Reserving the tape drive that is already reserved has no
effect. For example,
.sp
.LP
\fBioctl(fd, MTIOCRESERVE);\fR
.sp
.LP
The \fBMTIOCRELEASE\fR ioctl reverts back to the default behavior of reserve on
open/release on close operation, and a release will occur during the next
close. Releasing the tape drive that is already released has no effect. For
example,
.sp
.LP
\fBioctl(fd, MTIOCRELEASE);\fR
.sp
.LP
The \fBMTIOCFORCERESERVE\fR ioctl breaks a reservation held by another host,
interrupting any I/O in progress by that other host, and then reserves the tape
unit. This ioctl can be executed only with super-user privileges. It is
recommended to open the tape device in \fBO_NDELAY\fR mode when this ioctl
needs to be executed, otherwise the open will fail if another host indeed has
it reserved. For example,
.sp
.in +2
.nf
ioctl(fd, MTIOCFORCERESERVE);
.fi
.in -2

.SS "IOCTLS for Handling Tape Configuration Options"
.sp
.ne 2
.na
\fBMTIOCSHORTFMK\fR
.ad
.RS 23n
enables/disable support for writing short filemarks. This is specific to
Exabyte drives.
.RE

.sp
.ne 2
.na
\fBMTIOCREADIGNOREILI\fR
.ad
.RS 23n
enables/disable supress incorrect length indicator support during reads
.RE

.sp
.ne 2
.na
\fBMTIOCREADIGNOREEOFS\fR
.ad
.RS 23n
enables/disable support for reading past two EOF marks which otherwise indicate
End-Of-recording-Media (EOM) in the case of 1/2" reel tape drives
.RE

.sp
.LP
The \fBMTIOCSHORTFMK\fR ioctl enables or disables support for short filemarks.
This ioctl is only applicable to Exabyte drives which support short filemarks.
As an argument, it takes a pointer to an integer.  If 0 (zero) is the
specified integer, then long filemarks will be written. If 1 is the  specified
integer, then short filemarks will be written. The specified tape bahavior will
be in effect until the device is closed.
.sp
.LP
For example:
.sp
.in +2
.nf
int on = 1;
int off = 0;
/* enable short filemarks */
ioctl(fd, MTIOSHORTFMK, &on);
/* disable short filemarks */
ioctl(fd, MTIOCSHORTFMK, &off);
.fi
.in -2

.sp
.LP
Tape drives which do not support short filemarks will return an \fBerrno\fR of
\fBENOTTY.\fR
.sp
.LP
The \fBMTIOCREADIGNOREILI\fR ioctl enables or disables the suppress incorrect
length indicator (SILI) support during reads.  As an argument, it takes a
pointer to an integer.   If 0 (zero) is the specified integer, SILI will not be
used during reads and incorrect length indicator will not be supressed.  If 1
is  the specified integer, SILI will be used during reads and incorrect length
indicator will be supressed.  The specified  tape bahavior will be in effect
until the device is closed.
.sp
.LP
For example:
.sp
.in +2
.nf
int on = 1;
int off = 0;
ioctl(fd, MTIOREADIGNOREILI, &on);
ioctl(fd, MTIOREADIGNOREILI, &off);
.fi
.in -2

.sp
.LP
The \fBMTIOCREADIGNOREEOFS\fR ioctl enables or disables support for reading
past double EOF marks which otherwise indicate End-Of-recorded-media (EOM) in
the case of 1/2" reel tape drives.  As an argument, it takes a pointer to an
integer.   If 0 (zero) is the specified integer, then double EOF marks indicate
End-Of-recodred-media (EOD). If 1 is the specified integer, the double EOF
marks no longer indicate EOM, thus allowing applications to read past two EOF
marks.  In this case it is the responsibility of the application to detect
end-of-recorded-media (EOM).  The specified  tape bahavior will be in effect
until the device is closed.
.sp
.LP
For example:
.sp
.in +2
.nf
int on = 1;
int off = 0;
ioctl(fd, MTIOREADIGNOREEOFS, &on);
ioctl(fd, MTIOREADIGNOREEOFS, &off);
.fi
.in -2

.sp
.LP
Tape drives other than 1/2" reel tapes will return an \fBerrno\fR of
\fBENOTTY.\fR
.SH EXAMPLES
.LP
\fBExample 1 \fRTape Positioning and Tape Drives
.sp
.LP
Suppose you have written three files to the non-rewinding 1/2" tape device,
\fB/dev/rmt/0ln,\fR and that you want to go back and \fBdd\fR(1M) the second
file off the tape. The commands to do this are:

.sp
.in +2
.nf
mt \fB-F\fR /dev/rmt/0lbn bsf 3
mt \fB-F\fR /dev/rmt/0lbn fsf 1
dd if=/dev/rmt/0ln
.fi
.in -2

.sp
.LP
To accomplish the same tape positioning in a C program, followed by a get
status ioctl:

.sp
.in +2
.nf
struct mtop mt_command;
struct mtget mt_status;
mt_command.mt_op = MTBSF;
mt_command.mt_count = 3;
ioctl(fd, MTIOCTOP, &mt_command);
mt_command.mt_op = MTFSF;
mt_command.mt_count = 1;
ioctl(fd, MTIOCTOP, &mt_command);
ioctl(fd, MTIOCGET, (char *)&mt_status);
.fi
.in -2

.sp
.LP
or

.sp
.in +2
.nf
mt_command.mt_op = MTNBSF;
mt_command.mt_count = 2;
ioctl(fd, MTIOCTOP, &mt_command);
ioctl(fd, MTIOCGET, (char *)&mt_status);
.fi
.in -2

.sp
.LP
To get information about the tape drive:

.sp
.in +2
.nf
struct mtdrivetype mtdt;
struct mtdrivetype_request mtreq;
mtreq.size = sizeof(struct mtdrivetype);
mtreq.mtdtp = &mtdt;
ioctl(fd, MTIOCGETDRIVETYPE, &mtreq);
.fi
.in -2

.SH FILES
.sp
.LP
\fB/dev/rmt/\fR\fI<unit number><density>\fR[\fI<BSD behavior>\fR][\fI<no
rewind>\fR]
.sp
.LP
Where \fIdensity\fR can be \fBl,\fR \fBm,\fR \fBh,\fR \fBu/c\fR (low, medium,
high, ultra/compressed, respectively), the \fIBSD behavior \fR option is
\fBb\fR, and the \fIno rewind \fR option is \fBn\fR.
.sp
.LP
For example, \fB/dev/rmt/0hbn\fR specifies unit 0, high density, \fBBSD\fR
behavior and no rewind.
.SH SEE ALSO
.sp
.LP
\fBmt\fR(1), \fBtar\fR(1), \fBdd\fR(1M), \fBopen\fR(2), \fBread\fR(2),
\fBwrite\fR(2), \fBaioread\fR(3C), \fBaiowrite\fR(3C), \fBar.h\fR(3HEAD),
\fBst\fR(7D)
.sp
.LP
\fI1/4 Inch Tape Drive Tutorial\fR