#
# This file is provided under a CDDLv1 license.  When using or
# redistributing this file, you may do so under this license.
# In redistributing this file this license must be included
# and no other modification of this header file is permitted.
#
# CDDL LICENSE SUMMARY
#
# Copyright(c) 1999 - 2009 Intel Corporation. All rights reserved.
#
# The contents of this file are subject to the terms of Version
# 1.0 of the Common Development and Distribution License (the "License").
#
# You should have received a copy of the License with this software.
# You can obtain a copy of the License at
#	http://www.opensolaris.org/os/licensing.
# See the License for the specific language governing permissions
# and limitations under the License.
#
#
# Copyright 2009 Sun Microsystems, Inc.  All rights reserved.
# Use is subject to license terms of the CDDLv1.
#
#
# Driver.conf file for Intel e1000g Gigabit Ethernet Adapter
#
ForceSpeedDuplex=7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7;
        # This will force Speed and Duplex for following settings for a typical instance.
        # 1 will set the 10 Mbps speed and Half Duplex mode.
        # 2 will set the 10 Mbps speed and Full Duplex mode.
        # 3 will set the 100 Mbps speed and half Duplex mode.
        # 4 will set the 100 Mbps speed and Full Duplex mode.
        # 7 will let adapter autonegotiate.     
AutoNegAdvertised=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0;
        # This parameter determines the speed/duplex options that will be
        # advertised during auto-negotiation. This is a bitmap with the 
        # following settings.
        # Bit    |  7  |  6  |   5   |   4   |  3   |  2   |  1  |  0
        # Setting| N/A | N/A | 1000F |  N/A  | 100F | 100H | 10F | 10H
        #
        # For example:
        # To advertise 10 Half only AutoNegAdvertised   =  1
        # To advertise 10 Full only AutoNegAdvertised   =  2            
        # To advertise 10 Half/Full AutoNegAdvertised   =  3
        # To advertise 100 Half only AutoNegAdvertised  =  4
        # To advertise 100 Full only AutoNegAdvertised  =  8
        # To advertise 100 Half/Full AutoNegAdvertised  = 12
        # To advertise 1000 Full only AutoNegAdvertised = 32    
        # To advertise all speeds AutoNegAdvertised     = 47             
MaxFrameSize=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0;
        # 0 is for normal ethernet frames.
        # 1 is for upto 4k size frames.
        # 2 is for upto 8k size frames.
        # 3 is for upto 16k size frames.
	#
	# These are maximum frame limits, not the ethernet payload size
	# (usually called MTU).  Your actual ethernet MTU is determined by frame
	# size limit and protocol stack configuration (please refer to ndd
	# command man pages)
	#
	# For Jumbo Frame Support (9k ethernet packet) use 3 (upto 16k size
	# frames).  On PCH adapter type (82577 and 82578) you can configure up
	# to 4k size frames.  The 4k size is only allowed at 1gig speed, so if
	# you select 4k frames size, you cannot force or autonegotiate the
	# 10/100 speed options.
FlowControl=3,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3;
        # 0:  Flow control is completely disabled
        # 1:  Rx flow control is enabled (we can receive pause frames
        #     but not send pause frames).
        # 2:  Tx flow control is enabled (we can send pause frames
        #     but we do not receiving pause frames).
        # 3:  Both Rx and TX flow control (symmetric) is enabled.
        # 4:  No software override.  The flow control configuration
        #     in the EEPROM is used.
TbiCompatibilityEnable=1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1;
        # 1 turns it on and 0 turns it off.
        # Some switches as Cisco 6500/Foundary still operate in TBI mode. 
        # This setting will fix the problems seen with odd byte packets.
        # This setting is valid only for 82543GC based copper adapters.
SetMasterSlave=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0;
	# 0 sets to hardware default
	# 1 forces master
	# 2 forces slave
	# 3 forces auto
	# This setting controls the PHY master/slave setting. Manually forcing
	# master or slave can help reduce time to link with some switches
	# (Planex 08TX and IO Data switches).  It is recommended that this 
        # setting remain at the hardware default.