/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2008 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #pragma ident "%Z%%M% %I% %E% SMI" #include "bge_impl.h" #include #include /* * This is the string displayed by modinfo, etc. * Make sure you keep the version ID up to date! */ static char bge_ident[] = "Broadcom Gb Ethernet v0.67"; /* * Property names */ static char debug_propname[] = "bge-debug-flags"; static char clsize_propname[] = "cache-line-size"; static char latency_propname[] = "latency-timer"; static char localmac_boolname[] = "local-mac-address?"; static char localmac_propname[] = "local-mac-address"; static char macaddr_propname[] = "mac-address"; static char subdev_propname[] = "subsystem-id"; static char subven_propname[] = "subsystem-vendor-id"; static char rxrings_propname[] = "bge-rx-rings"; static char txrings_propname[] = "bge-tx-rings"; static char fm_cap[] = "fm-capable"; static char default_mtu[] = "default_mtu"; static int bge_add_intrs(bge_t *, int); static void bge_rem_intrs(bge_t *); /* * Describes the chip's DMA engine */ static ddi_dma_attr_t dma_attr = { DMA_ATTR_V0, /* dma_attr version */ 0x0000000000000000ull, /* dma_attr_addr_lo */ 0xFFFFFFFFFFFFFFFFull, /* dma_attr_addr_hi */ 0x00000000FFFFFFFFull, /* dma_attr_count_max */ 0x0000000000000001ull, /* dma_attr_align */ 0x00000FFF, /* dma_attr_burstsizes */ 0x00000001, /* dma_attr_minxfer */ 0x000000000000FFFFull, /* dma_attr_maxxfer */ 0xFFFFFFFFFFFFFFFFull, /* dma_attr_seg */ 1, /* dma_attr_sgllen */ 0x00000001, /* dma_attr_granular */ DDI_DMA_FLAGERR /* dma_attr_flags */ }; /* * PIO access attributes for registers */ static ddi_device_acc_attr_t bge_reg_accattr = { DDI_DEVICE_ATTR_V0, DDI_NEVERSWAP_ACC, DDI_STRICTORDER_ACC, DDI_FLAGERR_ACC }; /* * DMA access attributes for descriptors: NOT to be byte swapped. */ static ddi_device_acc_attr_t bge_desc_accattr = { DDI_DEVICE_ATTR_V0, DDI_NEVERSWAP_ACC, DDI_STRICTORDER_ACC, DDI_FLAGERR_ACC }; /* * DMA access attributes for data: NOT to be byte swapped. */ static ddi_device_acc_attr_t bge_data_accattr = { DDI_DEVICE_ATTR_V0, DDI_NEVERSWAP_ACC, DDI_STRICTORDER_ACC }; static int bge_m_start(void *); static void bge_m_stop(void *); static int bge_m_promisc(void *, boolean_t); static int bge_m_multicst(void *, boolean_t, const uint8_t *); static int bge_m_unicst(void *, const uint8_t *); static void bge_m_resources(void *); static void bge_m_ioctl(void *, queue_t *, mblk_t *); static boolean_t bge_m_getcapab(void *, mac_capab_t, void *); static int bge_unicst_set(void *, const uint8_t *, mac_addr_slot_t); static int bge_m_unicst_add(void *, mac_multi_addr_t *); static int bge_m_unicst_remove(void *, mac_addr_slot_t); static int bge_m_unicst_modify(void *, mac_multi_addr_t *); static int bge_m_unicst_get(void *, mac_multi_addr_t *); static int bge_m_setprop(void *, const char *, mac_prop_id_t, uint_t, const void *); static int bge_m_getprop(void *, const char *, mac_prop_id_t, uint_t, uint_t, void *); static int bge_set_priv_prop(bge_t *, const char *, uint_t, const void *); static int bge_get_priv_prop(bge_t *, const char *, uint_t, uint_t, void *); #define BGE_M_CALLBACK_FLAGS\ (MC_RESOURCES | MC_IOCTL | MC_GETCAPAB | MC_SETPROP | MC_GETPROP) static mac_callbacks_t bge_m_callbacks = { BGE_M_CALLBACK_FLAGS, bge_m_stat, bge_m_start, bge_m_stop, bge_m_promisc, bge_m_multicst, bge_m_unicst, bge_m_tx, bge_m_resources, bge_m_ioctl, bge_m_getcapab, NULL, NULL, bge_m_setprop, bge_m_getprop }; mac_priv_prop_t bge_priv_prop[] = { {"_adv_asym_pause_cap", MAC_PROP_PERM_RW}, {"_adv_pause_cap", MAC_PROP_PERM_RW} }; #define BGE_MAX_PRIV_PROPS \ (sizeof (bge_priv_prop) / sizeof (mac_priv_prop_t)) /* * ========== Transmit and receive ring reinitialisation ========== */ /* * These routines each reset the specified ring to an initial * state, assuming that the corresponding routine has already * been called exactly once. */ static void bge_reinit_send_ring(send_ring_t *srp) { bge_queue_t *txbuf_queue; bge_queue_item_t *txbuf_head; sw_txbuf_t *txbuf; sw_sbd_t *ssbdp; uint32_t slot; /* * Reinitialise control variables ... */ srp->tx_flow = 0; srp->tx_next = 0; srp->txfill_next = 0; srp->tx_free = srp->desc.nslots; ASSERT(mutex_owned(srp->tc_lock)); srp->tc_next = 0; srp->txpkt_next = 0; srp->tx_block = 0; srp->tx_nobd = 0; srp->tx_nobuf = 0; /* * Initialize the tx buffer push queue */ mutex_enter(srp->freetxbuf_lock); mutex_enter(srp->txbuf_lock); txbuf_queue = &srp->freetxbuf_queue; txbuf_queue->head = NULL; txbuf_queue->count = 0; txbuf_queue->lock = srp->freetxbuf_lock; srp->txbuf_push_queue = txbuf_queue; /* * Initialize the tx buffer pop queue */ txbuf_queue = &srp->txbuf_queue; txbuf_queue->head = NULL; txbuf_queue->count = 0; txbuf_queue->lock = srp->txbuf_lock; srp->txbuf_pop_queue = txbuf_queue; txbuf_head = srp->txbuf_head; txbuf = srp->txbuf; for (slot = 0; slot < srp->tx_buffers; ++slot) { txbuf_head->item = txbuf; txbuf_head->next = txbuf_queue->head; txbuf_queue->head = txbuf_head; txbuf_queue->count++; txbuf++; txbuf_head++; } mutex_exit(srp->txbuf_lock); mutex_exit(srp->freetxbuf_lock); /* * Zero and sync all the h/w Send Buffer Descriptors */ DMA_ZERO(srp->desc); DMA_SYNC(srp->desc, DDI_DMA_SYNC_FORDEV); bzero(srp->pktp, BGE_SEND_BUF_MAX * sizeof (*srp->pktp)); ssbdp = srp->sw_sbds; for (slot = 0; slot < srp->desc.nslots; ++ssbdp, ++slot) ssbdp->pbuf = NULL; } static void bge_reinit_recv_ring(recv_ring_t *rrp) { /* * Reinitialise control variables ... */ rrp->rx_next = 0; } static void bge_reinit_buff_ring(buff_ring_t *brp, uint32_t ring) { bge_rbd_t *hw_rbd_p; sw_rbd_t *srbdp; uint32_t bufsize; uint32_t nslots; uint32_t slot; static uint16_t ring_type_flag[BGE_BUFF_RINGS_MAX] = { RBD_FLAG_STD_RING, RBD_FLAG_JUMBO_RING, RBD_FLAG_MINI_RING }; /* * Zero, initialise and sync all the h/w Receive Buffer Descriptors * Note: all the remaining fields (, , , * , , , and ) * should be zeroed, and so don't need to be set up specifically * once the whole area has been cleared. */ DMA_ZERO(brp->desc); hw_rbd_p = DMA_VPTR(brp->desc); nslots = brp->desc.nslots; ASSERT(brp->buf[0].nslots == nslots/BGE_SPLIT); bufsize = brp->buf[0].size; srbdp = brp->sw_rbds; for (slot = 0; slot < nslots; ++hw_rbd_p, ++srbdp, ++slot) { hw_rbd_p->host_buf_addr = srbdp->pbuf.cookie.dmac_laddress; hw_rbd_p->index = (uint16_t)slot; hw_rbd_p->len = (uint16_t)bufsize; hw_rbd_p->opaque = srbdp->pbuf.token; hw_rbd_p->flags |= ring_type_flag[ring]; } DMA_SYNC(brp->desc, DDI_DMA_SYNC_FORDEV); /* * Finally, reinitialise the ring control variables ... */ brp->rf_next = (nslots != 0) ? (nslots-1) : 0; } /* * Reinitialize all rings */ static void bge_reinit_rings(bge_t *bgep) { uint32_t ring; ASSERT(mutex_owned(bgep->genlock)); /* * Send Rings ... */ for (ring = 0; ring < bgep->chipid.tx_rings; ++ring) bge_reinit_send_ring(&bgep->send[ring]); /* * Receive Return Rings ... */ for (ring = 0; ring < bgep->chipid.rx_rings; ++ring) bge_reinit_recv_ring(&bgep->recv[ring]); /* * Receive Producer Rings ... */ for (ring = 0; ring < BGE_BUFF_RINGS_USED; ++ring) bge_reinit_buff_ring(&bgep->buff[ring], ring); } /* * ========== Internal state management entry points ========== */ #undef BGE_DBG #define BGE_DBG BGE_DBG_NEMO /* debug flag for this code */ /* * These routines provide all the functionality required by the * corresponding GLD entry points, but don't update the GLD state * so they can be called internally without disturbing our record * of what GLD thinks we should be doing ... */ /* * bge_reset() -- reset h/w & rings to initial state */ static int #ifdef BGE_IPMI_ASF bge_reset(bge_t *bgep, uint_t asf_mode) #else bge_reset(bge_t *bgep) #endif { uint32_t ring; int retval; BGE_TRACE(("bge_reset($%p)", (void *)bgep)); ASSERT(mutex_owned(bgep->genlock)); /* * Grab all the other mutexes in the world (this should * ensure no other threads are manipulating driver state) */ for (ring = 0; ring < BGE_RECV_RINGS_MAX; ++ring) mutex_enter(bgep->recv[ring].rx_lock); for (ring = 0; ring < BGE_BUFF_RINGS_MAX; ++ring) mutex_enter(bgep->buff[ring].rf_lock); rw_enter(bgep->errlock, RW_WRITER); for (ring = 0; ring < BGE_SEND_RINGS_MAX; ++ring) mutex_enter(bgep->send[ring].tx_lock); for (ring = 0; ring < BGE_SEND_RINGS_MAX; ++ring) mutex_enter(bgep->send[ring].tc_lock); #ifdef BGE_IPMI_ASF retval = bge_chip_reset(bgep, B_TRUE, asf_mode); #else retval = bge_chip_reset(bgep, B_TRUE); #endif bge_reinit_rings(bgep); /* * Free the world ... */ for (ring = BGE_SEND_RINGS_MAX; ring-- > 0; ) mutex_exit(bgep->send[ring].tc_lock); for (ring = 0; ring < BGE_SEND_RINGS_MAX; ++ring) mutex_exit(bgep->send[ring].tx_lock); rw_exit(bgep->errlock); for (ring = BGE_BUFF_RINGS_MAX; ring-- > 0; ) mutex_exit(bgep->buff[ring].rf_lock); for (ring = BGE_RECV_RINGS_MAX; ring-- > 0; ) mutex_exit(bgep->recv[ring].rx_lock); BGE_DEBUG(("bge_reset($%p) done", (void *)bgep)); return (retval); } /* * bge_stop() -- stop processing, don't reset h/w or rings */ static void bge_stop(bge_t *bgep) { BGE_TRACE(("bge_stop($%p)", (void *)bgep)); ASSERT(mutex_owned(bgep->genlock)); #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { bgep->asf_pseudostop = B_TRUE; } else { #endif bge_chip_stop(bgep, B_FALSE); #ifdef BGE_IPMI_ASF } #endif BGE_DEBUG(("bge_stop($%p) done", (void *)bgep)); } /* * bge_start() -- start transmitting/receiving */ static int bge_start(bge_t *bgep, boolean_t reset_phys) { int retval; BGE_TRACE(("bge_start($%p, %d)", (void *)bgep, reset_phys)); ASSERT(mutex_owned(bgep->genlock)); /* * Start chip processing, including enabling interrupts */ retval = bge_chip_start(bgep, reset_phys); BGE_DEBUG(("bge_start($%p, %d) done", (void *)bgep, reset_phys)); return (retval); } /* * bge_restart - restart transmitting/receiving after error or suspend */ int bge_restart(bge_t *bgep, boolean_t reset_phys) { int retval = DDI_SUCCESS; ASSERT(mutex_owned(bgep->genlock)); #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { if (bge_reset(bgep, ASF_MODE_POST_INIT) != DDI_SUCCESS) retval = DDI_FAILURE; } else if (bge_reset(bgep, ASF_MODE_NONE) != DDI_SUCCESS) retval = DDI_FAILURE; #else if (bge_reset(bgep) != DDI_SUCCESS) retval = DDI_FAILURE; #endif if (bgep->bge_mac_state == BGE_MAC_STARTED) { if (bge_start(bgep, reset_phys) != DDI_SUCCESS) retval = DDI_FAILURE; bgep->watchdog = 0; ddi_trigger_softintr(bgep->drain_id); } BGE_DEBUG(("bge_restart($%p, %d) done", (void *)bgep, reset_phys)); return (retval); } /* * ========== Nemo-required management entry points ========== */ #undef BGE_DBG #define BGE_DBG BGE_DBG_NEMO /* debug flag for this code */ /* * bge_m_stop() -- stop transmitting/receiving */ static void bge_m_stop(void *arg) { bge_t *bgep = arg; /* private device info */ send_ring_t *srp; uint32_t ring; BGE_TRACE(("bge_m_stop($%p)", arg)); /* * Just stop processing, then record new GLD state */ mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ mutex_exit(bgep->genlock); return; } bge_stop(bgep); bgep->link_update_timer = 0; bgep->link_state = LINK_STATE_UNKNOWN; mac_link_update(bgep->mh, bgep->link_state); /* * Free the possible tx buffers allocated in tx process. */ #ifdef BGE_IPMI_ASF if (!bgep->asf_pseudostop) #endif { rw_enter(bgep->errlock, RW_WRITER); for (ring = 0; ring < bgep->chipid.tx_rings; ++ring) { srp = &bgep->send[ring]; mutex_enter(srp->tx_lock); if (srp->tx_array > 1) bge_free_txbuf_arrays(srp); mutex_exit(srp->tx_lock); } rw_exit(bgep->errlock); } bgep->bge_mac_state = BGE_MAC_STOPPED; BGE_DEBUG(("bge_m_stop($%p) done", arg)); if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); mutex_exit(bgep->genlock); } /* * bge_m_start() -- start transmitting/receiving */ static int bge_m_start(void *arg) { bge_t *bgep = arg; /* private device info */ BGE_TRACE(("bge_m_start($%p)", arg)); /* * Start processing and record new GLD state */ mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { if ((bgep->asf_status == ASF_STAT_RUN) && (bgep->asf_pseudostop)) { bgep->bge_mac_state = BGE_MAC_STARTED; mutex_exit(bgep->genlock); return (0); } } if (bge_reset(bgep, ASF_MODE_INIT) != DDI_SUCCESS) { #else if (bge_reset(bgep) != DDI_SUCCESS) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (bge_start(bgep, B_TRUE) != DDI_SUCCESS) { (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } bgep->bge_mac_state = BGE_MAC_STARTED; BGE_DEBUG(("bge_m_start($%p) done", arg)); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { if (bgep->asf_status != ASF_STAT_RUN) { /* start ASF heart beat */ bgep->asf_timeout_id = timeout(bge_asf_heartbeat, (void *)bgep, drv_usectohz(BGE_ASF_HEARTBEAT_INTERVAL)); bgep->asf_status = ASF_STAT_RUN; } } #endif mutex_exit(bgep->genlock); return (0); } /* * bge_m_unicst() -- set the physical network address */ static int bge_m_unicst(void *arg, const uint8_t *macaddr) { /* * Request to set address in * address slot 0, i.e., default address */ return (bge_unicst_set(arg, macaddr, 0)); } /* * bge_unicst_set() -- set the physical network address */ static int bge_unicst_set(void *arg, const uint8_t *macaddr, mac_addr_slot_t slot) { bge_t *bgep = arg; /* private device info */ BGE_TRACE(("bge_m_unicst_set($%p, %s)", arg, ether_sprintf((void *)macaddr))); /* * Remember the new current address in the driver state * Sync the chip's idea of the address too ... */ mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } ethaddr_copy(macaddr, bgep->curr_addr[slot].addr); #ifdef BGE_IPMI_ASF if (bge_chip_sync(bgep, B_FALSE) == DDI_FAILURE) { #else if (bge_chip_sync(bgep) == DDI_FAILURE) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { /* * The above bge_chip_sync() function wrote the ethernet MAC * addresses registers which destroyed the IPMI/ASF sideband. * Here, we have to reset chip to make IPMI/ASF sideband work. */ if (bgep->asf_status == ASF_STAT_RUN) { /* * We must stop ASF heart beat before bge_chip_stop(), * otherwise some computers (ex. IBM HS20 blade server) * may crash. */ bge_asf_update_status(bgep); bge_asf_stop_timer(bgep); bgep->asf_status = ASF_STAT_STOP; bge_asf_pre_reset_operations(bgep, BGE_INIT_RESET); } bge_chip_stop(bgep, B_FALSE); if (bge_restart(bgep, B_FALSE) == DDI_FAILURE) { (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } /* * Start our ASF heartbeat counter as soon as possible. */ if (bgep->asf_status != ASF_STAT_RUN) { /* start ASF heart beat */ bgep->asf_timeout_id = timeout(bge_asf_heartbeat, (void *)bgep, drv_usectohz(BGE_ASF_HEARTBEAT_INTERVAL)); bgep->asf_status = ASF_STAT_RUN; } } #endif BGE_DEBUG(("bge_m_unicst_set($%p) done", arg)); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } mutex_exit(bgep->genlock); return (0); } /* * The following four routines are used as callbacks for multiple MAC * address support: * - bge_m_unicst_add(void *, mac_multi_addr_t *); * - bge_m_unicst_remove(void *, mac_addr_slot_t); * - bge_m_unicst_modify(void *, mac_multi_addr_t *); * - bge_m_unicst_get(void *, mac_multi_addr_t *); */ /* * bge_m_unicst_add() - will find an unused address slot, set the * address value to the one specified, reserve that slot and enable * the NIC to start filtering on the new MAC address. * address slot. Returns 0 on success. */ static int bge_m_unicst_add(void *arg, mac_multi_addr_t *maddr) { bge_t *bgep = arg; /* private device info */ mac_addr_slot_t slot; int err; if (mac_unicst_verify(bgep->mh, maddr->mma_addr, maddr->mma_addrlen) == B_FALSE) return (EINVAL); mutex_enter(bgep->genlock); if (bgep->unicst_addr_avail == 0) { /* no slots available */ mutex_exit(bgep->genlock); return (ENOSPC); } /* * Primary/default address is in slot 0. The next three * addresses are the multiple MAC addresses. So multiple * MAC address 0 is in slot 1, 1 in slot 2, and so on. * So the first multiple MAC address resides in slot 1. */ for (slot = 1; slot < bgep->unicst_addr_total; slot++) { if (bgep->curr_addr[slot].set == B_FALSE) { bgep->curr_addr[slot].set = B_TRUE; break; } } ASSERT(slot < bgep->unicst_addr_total); bgep->unicst_addr_avail--; mutex_exit(bgep->genlock); maddr->mma_slot = slot; if ((err = bge_unicst_set(bgep, maddr->mma_addr, slot)) != 0) { mutex_enter(bgep->genlock); bgep->curr_addr[slot].set = B_FALSE; bgep->unicst_addr_avail++; mutex_exit(bgep->genlock); } return (err); } /* * bge_m_unicst_remove() - removes a MAC address that was added by a * call to bge_m_unicst_add(). The slot number that was returned in * add() is passed in the call to remove the address. * Returns 0 on success. */ static int bge_m_unicst_remove(void *arg, mac_addr_slot_t slot) { bge_t *bgep = arg; /* private device info */ if (slot <= 0 || slot >= bgep->unicst_addr_total) return (EINVAL); mutex_enter(bgep->genlock); if (bgep->curr_addr[slot].set == B_TRUE) { bgep->curr_addr[slot].set = B_FALSE; bgep->unicst_addr_avail++; mutex_exit(bgep->genlock); /* * Copy the default address to the passed slot */ return (bge_unicst_set(bgep, bgep->curr_addr[0].addr, slot)); } mutex_exit(bgep->genlock); return (EINVAL); } /* * bge_m_unicst_modify() - modifies the value of an address that * has been added by bge_m_unicst_add(). The new address, address * length and the slot number that was returned in the call to add * should be passed to bge_m_unicst_modify(). mma_flags should be * set to 0. Returns 0 on success. */ static int bge_m_unicst_modify(void *arg, mac_multi_addr_t *maddr) { bge_t *bgep = arg; /* private device info */ mac_addr_slot_t slot; if (mac_unicst_verify(bgep->mh, maddr->mma_addr, maddr->mma_addrlen) == B_FALSE) return (EINVAL); slot = maddr->mma_slot; if (slot <= 0 || slot >= bgep->unicst_addr_total) return (EINVAL); mutex_enter(bgep->genlock); if (bgep->curr_addr[slot].set == B_TRUE) { mutex_exit(bgep->genlock); return (bge_unicst_set(bgep, maddr->mma_addr, slot)); } mutex_exit(bgep->genlock); return (EINVAL); } /* * bge_m_unicst_get() - will get the MAC address and all other * information related to the address slot passed in mac_multi_addr_t. * mma_flags should be set to 0 in the call. * On return, mma_flags can take the following values: * 1) MMAC_SLOT_UNUSED * 2) MMAC_SLOT_USED | MMAC_VENDOR_ADDR * 3) MMAC_SLOT_UNUSED | MMAC_VENDOR_ADDR * 4) MMAC_SLOT_USED */ static int bge_m_unicst_get(void *arg, mac_multi_addr_t *maddr) { bge_t *bgep = arg; /* private device info */ mac_addr_slot_t slot; slot = maddr->mma_slot; if (slot <= 0 || slot >= bgep->unicst_addr_total) return (EINVAL); mutex_enter(bgep->genlock); if (bgep->curr_addr[slot].set == B_TRUE) { ethaddr_copy(bgep->curr_addr[slot].addr, maddr->mma_addr); maddr->mma_flags = MMAC_SLOT_USED; } else { maddr->mma_flags = MMAC_SLOT_UNUSED; } mutex_exit(bgep->genlock); return (0); } extern void bge_wake_factotum(bge_t *); static boolean_t bge_param_locked(mac_prop_id_t pr_num) { /* * All adv_* parameters are locked (read-only) while * the device is in any sort of loopback mode ... */ switch (pr_num) { case MAC_PROP_ADV_1000FDX_CAP: case MAC_PROP_EN_1000FDX_CAP: case MAC_PROP_ADV_1000HDX_CAP: case MAC_PROP_EN_1000HDX_CAP: case MAC_PROP_ADV_100FDX_CAP: case MAC_PROP_EN_100FDX_CAP: case MAC_PROP_ADV_100HDX_CAP: case MAC_PROP_EN_100HDX_CAP: case MAC_PROP_ADV_10FDX_CAP: case MAC_PROP_EN_10FDX_CAP: case MAC_PROP_ADV_10HDX_CAP: case MAC_PROP_EN_10HDX_CAP: case MAC_PROP_AUTONEG: case MAC_PROP_FLOWCTRL: return (B_TRUE); } return (B_FALSE); } /* * callback functions for set/get of properties */ static int bge_m_setprop(void *barg, const char *pr_name, mac_prop_id_t pr_num, uint_t pr_valsize, const void *pr_val) { bge_t *bgep = barg; int err = 0; uint32_t cur_mtu, new_mtu; uint_t maxsdu; link_flowctrl_t fl; mutex_enter(bgep->genlock); if (bgep->param_loop_mode != BGE_LOOP_NONE && bge_param_locked(pr_num)) { /* * All adv_* parameters are locked (read-only) * while the device is in any sort of loopback mode. */ mutex_exit(bgep->genlock); return (EBUSY); } if ((bgep->chipid.flags & CHIP_FLAG_SERDES) && ((pr_num == MAC_PROP_EN_100FDX_CAP) || (pr_num == MAC_PROP_EN_100FDX_CAP) || (pr_num == MAC_PROP_EN_10FDX_CAP) || (pr_num == MAC_PROP_EN_10HDX_CAP))) { /* * these properties are read/write on copper, * read-only and 0 on serdes */ mutex_exit(bgep->genlock); return (ENOTSUP); } switch (pr_num) { case MAC_PROP_EN_1000FDX_CAP: bgep->param_en_1000fdx = *(uint8_t *)pr_val; bgep->param_adv_1000fdx = *(uint8_t *)pr_val; goto reprogram; case MAC_PROP_EN_1000HDX_CAP: bgep->param_en_1000hdx = *(uint8_t *)pr_val; bgep->param_adv_1000hdx = *(uint8_t *)pr_val; goto reprogram; case MAC_PROP_EN_100FDX_CAP: bgep->param_en_100fdx = *(uint8_t *)pr_val; bgep->param_adv_100fdx = *(uint8_t *)pr_val; goto reprogram; case MAC_PROP_EN_100HDX_CAP: bgep->param_en_100hdx = *(uint8_t *)pr_val; bgep->param_adv_100hdx = *(uint8_t *)pr_val; goto reprogram; case MAC_PROP_EN_10FDX_CAP: bgep->param_en_10fdx = *(uint8_t *)pr_val; bgep->param_adv_10fdx = *(uint8_t *)pr_val; goto reprogram; case MAC_PROP_EN_10HDX_CAP: bgep->param_en_10hdx = *(uint8_t *)pr_val; bgep->param_adv_10hdx = *(uint8_t *)pr_val; reprogram: if (err == 0 && bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; break; case MAC_PROP_ADV_1000FDX_CAP: case MAC_PROP_ADV_1000HDX_CAP: case MAC_PROP_ADV_100FDX_CAP: case MAC_PROP_ADV_100HDX_CAP: case MAC_PROP_ADV_10FDX_CAP: case MAC_PROP_ADV_10HDX_CAP: case MAC_PROP_STATUS: case MAC_PROP_SPEED: case MAC_PROP_DUPLEX: err = ENOTSUP; /* read-only prop. Can't set this */ break; case MAC_PROP_AUTONEG: bgep->param_adv_autoneg = *(uint8_t *)pr_val; if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; break; case MAC_PROP_MTU: cur_mtu = bgep->chipid.default_mtu; bcopy(pr_val, &new_mtu, sizeof (new_mtu)); if (new_mtu == cur_mtu) { err = 0; break; } if (new_mtu < BGE_DEFAULT_MTU || new_mtu > BGE_MAXIMUM_MTU) { err = EINVAL; break; } if ((new_mtu > BGE_DEFAULT_MTU) && (bgep->chipid.flags & CHIP_FLAG_NO_JUMBO)) { err = EINVAL; break; } if (bgep->bge_mac_state == BGE_MAC_STARTED) { err = EBUSY; break; } bgep->chipid.default_mtu = new_mtu; if (bge_chip_id_init(bgep)) { err = EINVAL; break; } maxsdu = bgep->chipid.ethmax_size - sizeof (struct ether_header); err = mac_maxsdu_update(bgep->mh, maxsdu); if (err == 0) { bgep->bge_dma_error = B_TRUE; bgep->manual_reset = B_TRUE; bge_chip_stop(bgep, B_TRUE); bge_wake_factotum(bgep); err = 0; } break; case MAC_PROP_FLOWCTRL: bcopy(pr_val, &fl, sizeof (fl)); switch (fl) { default: err = ENOTSUP; break; case LINK_FLOWCTRL_NONE: bgep->param_adv_pause = 0; bgep->param_adv_asym_pause = 0; bgep->param_link_rx_pause = B_FALSE; bgep->param_link_tx_pause = B_FALSE; break; case LINK_FLOWCTRL_RX: if (!((bgep->param_lp_pause == 0) && (bgep->param_lp_asym_pause == 1))) { err = EINVAL; break; } bgep->param_adv_pause = 1; bgep->param_adv_asym_pause = 1; bgep->param_link_rx_pause = B_TRUE; bgep->param_link_tx_pause = B_FALSE; break; case LINK_FLOWCTRL_TX: if (!((bgep->param_lp_pause == 1) && (bgep->param_lp_asym_pause == 1))) { err = EINVAL; break; } bgep->param_adv_pause = 0; bgep->param_adv_asym_pause = 1; bgep->param_link_rx_pause = B_FALSE; bgep->param_link_tx_pause = B_TRUE; break; case LINK_FLOWCTRL_BI: if (bgep->param_lp_pause != 1) { err = EINVAL; break; } bgep->param_adv_pause = 1; bgep->param_link_rx_pause = B_TRUE; bgep->param_link_tx_pause = B_TRUE; break; } if (err == 0) { if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; } break; case MAC_PROP_PRIVATE: err = bge_set_priv_prop(bgep, pr_name, pr_valsize, pr_val); break; default: err = ENOTSUP; break; } mutex_exit(bgep->genlock); return (err); } static int bge_m_getprop(void *barg, const char *pr_name, mac_prop_id_t pr_num, uint_t pr_flags, uint_t pr_valsize, void *pr_val) { bge_t *bgep = barg; int err = 0; link_flowctrl_t fl; uint64_t speed; int flags = bgep->chipid.flags; boolean_t is_default = (pr_flags & MAC_PROP_DEFAULT); if (pr_valsize == 0) return (EINVAL); bzero(pr_val, pr_valsize); switch (pr_num) { case MAC_PROP_DUPLEX: if (pr_valsize < sizeof (link_duplex_t)) return (EINVAL); bcopy(&bgep->param_link_duplex, pr_val, sizeof (link_duplex_t)); break; case MAC_PROP_SPEED: if (pr_valsize < sizeof (speed)) return (EINVAL); speed = bgep->param_link_speed * 1000000ull; bcopy(&speed, pr_val, sizeof (speed)); break; case MAC_PROP_STATUS: if (pr_valsize < sizeof (link_state_t)) return (EINVAL); bcopy(&bgep->link_state, pr_val, sizeof (link_state_t)); break; case MAC_PROP_AUTONEG: if (is_default) *(uint8_t *)pr_val = 1; else *(uint8_t *)pr_val = bgep->param_adv_autoneg; break; case MAC_PROP_FLOWCTRL: if (pr_valsize < sizeof (fl)) return (EINVAL); if (is_default) { fl = LINK_FLOWCTRL_BI; bcopy(&fl, pr_val, sizeof (fl)); break; } if (bgep->param_link_rx_pause && !bgep->param_link_tx_pause) fl = LINK_FLOWCTRL_RX; if (!bgep->param_link_rx_pause && !bgep->param_link_tx_pause) fl = LINK_FLOWCTRL_NONE; if (!bgep->param_link_rx_pause && bgep->param_link_tx_pause) fl = LINK_FLOWCTRL_TX; if (bgep->param_link_rx_pause && bgep->param_link_tx_pause) fl = LINK_FLOWCTRL_BI; bcopy(&fl, pr_val, sizeof (fl)); break; case MAC_PROP_ADV_1000FDX_CAP: if (is_default) *(uint8_t *)pr_val = 1; else *(uint8_t *)pr_val = bgep->param_adv_1000fdx; break; case MAC_PROP_EN_1000FDX_CAP: if (is_default) *(uint8_t *)pr_val = 1; else *(uint8_t *)pr_val = bgep->param_en_1000fdx; break; case MAC_PROP_ADV_1000HDX_CAP: if (is_default) *(uint8_t *)pr_val = 1; else *(uint8_t *)pr_val = bgep->param_adv_1000hdx; break; case MAC_PROP_EN_1000HDX_CAP: if (is_default) *(uint8_t *)pr_val = 1; else *(uint8_t *)pr_val = bgep->param_en_1000hdx; break; case MAC_PROP_ADV_100FDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_adv_100fdx; } break; case MAC_PROP_EN_100FDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_en_100fdx; } break; case MAC_PROP_ADV_100HDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_adv_100hdx; } break; case MAC_PROP_EN_100HDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_en_100hdx; } break; case MAC_PROP_ADV_10FDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_adv_10fdx; } break; case MAC_PROP_EN_10FDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_en_10fdx; } break; case MAC_PROP_ADV_10HDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_adv_10hdx; } break; case MAC_PROP_EN_10HDX_CAP: if (is_default) { *(uint8_t *)pr_val = ((flags & CHIP_FLAG_SERDES) ? 0 : 1); } else { *(uint8_t *)pr_val = bgep->param_en_10hdx; } break; case MAC_PROP_ADV_100T4_CAP: case MAC_PROP_EN_100T4_CAP: *(uint8_t *)pr_val = 0; break; case MAC_PROP_PRIVATE: err = bge_get_priv_prop(bgep, pr_name, pr_flags, pr_valsize, pr_val); return (err); default: return (ENOTSUP); } return (0); } /* ARGSUSED */ static int bge_set_priv_prop(bge_t *bgep, const char *pr_name, uint_t pr_valsize, const void *pr_val) { int err = 0; long result; if (strcmp(pr_name, "_adv_pause_cap") == 0) { (void) ddi_strtol(pr_val, (char **)NULL, 0, &result); if (result > 1 || result < 0) { err = EINVAL; } else { bgep->param_adv_pause = (uint32_t)result; if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; } return (err); } if (strcmp(pr_name, "_adv_asym_pause_cap") == 0) { (void) ddi_strtol(pr_val, (char **)NULL, 0, &result); if (result > 1 || result < 0) { err = EINVAL; } else { bgep->param_adv_asym_pause = (uint32_t)result; if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; } return (err); } if (strcmp(pr_name, "_drain_max") == 0) { /* * on the Tx side, we need to update the h/w register for * real packet transmission per packet. The drain_max parameter * is used to reduce the register access. This parameter * controls the max number of packets that we will hold before * updating the bge h/w to trigger h/w transmit. The bge * chipset usually has a max of 512 Tx descriptors, thus * the upper bound on drain_max is 512. */ if (pr_val == NULL) { err = EINVAL; return (err); } (void) ddi_strtol(pr_val, (char **)NULL, 0, &result); if (result > 512 || result < 1) err = EINVAL; else { bgep->param_drain_max = (uint32_t)result; if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; } return (err); } if (strcmp(pr_name, "_msi_cnt") == 0) { if (pr_val == NULL) { err = EINVAL; return (err); } (void) ddi_strtol(pr_val, (char **)NULL, 0, &result); if (result > 7 || result < 0) err = EINVAL; else { bgep->param_msi_cnt = (uint32_t)result; if (bge_reprogram(bgep) == IOC_INVAL) err = EINVAL; } return (err); } if (strcmp(pr_name, "_intr_coalesce_blank_time") == 0) { if (ddi_strtol(pr_val, (char **)NULL, 0, &result) != 0) return (EINVAL); bgep->chipid.rx_ticks_norm = (uint32_t)result; return (0); } if (strcmp(pr_name, "_intr_coalesce_pkt_cnt") == 0) { if (ddi_strtol(pr_val, (char **)NULL, 0, &result) != 0) return (EINVAL); bgep->chipid.rx_count_norm = (uint32_t)result; return (0); } return (ENOTSUP); } static int bge_get_priv_prop(bge_t *bge, const char *pr_name, uint_t pr_flags, uint_t pr_valsize, void *pr_val) { int err = ENOTSUP; boolean_t is_default = (pr_flags & MAC_PROP_DEFAULT); int value; if (strcmp(pr_name, "_adv_pause_cap") == 0) { value = (is_default? 1 : bge->param_adv_pause); err = 0; goto done; } if (strcmp(pr_name, "_adv_asym_pause_cap") == 0) { value = (is_default? 1 : bge->param_adv_asym_pause); err = 0; goto done; } if (strcmp(pr_name, "_drain_max") == 0) { value = (is_default? 64 : bge->param_drain_max); err = 0; goto done; } if (strcmp(pr_name, "_msi_cnt") == 0) { value = (is_default? 0 : bge->param_msi_cnt); err = 0; goto done; } if (strcmp(pr_name, "_intr_coalesce_blank_time") == 0) { value = (is_default? bge_rx_ticks_norm : bge->chipid.rx_ticks_norm); err = 0; goto done; } if (strcmp(pr_name, "_intr_coalesce_pkt_cnt") == 0) { value = (is_default? bge_rx_count_norm : bge->chipid.rx_count_norm); err = 0; goto done; } done: if (err == 0) { (void) snprintf(pr_val, pr_valsize, "%d", value); } return (err); } /* * Compute the index of the required bit in the multicast hash map. * This must mirror the way the hardware actually does it! * See Broadcom document 570X-PG102-R page 125. */ static uint32_t bge_hash_index(const uint8_t *mca) { uint32_t hash; CRC32(hash, mca, ETHERADDRL, -1U, crc32_table); return (hash); } /* * bge_m_multicst_add() -- enable/disable a multicast address */ static int bge_m_multicst(void *arg, boolean_t add, const uint8_t *mca) { bge_t *bgep = arg; /* private device info */ uint32_t hash; uint32_t index; uint32_t word; uint32_t bit; uint8_t *refp; BGE_TRACE(("bge_m_multicst($%p, %s, %s)", arg, (add) ? "add" : "remove", ether_sprintf((void *)mca))); /* * Precalculate all required masks, pointers etc ... */ hash = bge_hash_index(mca); index = hash % BGE_HASH_TABLE_SIZE; word = index/32u; bit = 1 << (index % 32u); refp = &bgep->mcast_refs[index]; BGE_DEBUG(("bge_m_multicst: hash 0x%x index %d (%d:0x%x) = %d", hash, index, word, bit, *refp)); /* * We must set the appropriate bit in the hash map (and the * corresponding h/w register) when the refcount goes from 0 * to >0, and clear it when the last ref goes away (refcount * goes from >0 back to 0). If we change the hash map, we * must also update the chip's hardware map registers. */ mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (add) { if ((*refp)++ == 0) { bgep->mcast_hash[word] |= bit; #ifdef BGE_IPMI_ASF if (bge_chip_sync(bgep, B_TRUE) == DDI_FAILURE) { #else if (bge_chip_sync(bgep) == DDI_FAILURE) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } } } else { if (--(*refp) == 0) { bgep->mcast_hash[word] &= ~bit; #ifdef BGE_IPMI_ASF if (bge_chip_sync(bgep, B_TRUE) == DDI_FAILURE) { #else if (bge_chip_sync(bgep) == DDI_FAILURE) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } } } BGE_DEBUG(("bge_m_multicst($%p) done", arg)); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } mutex_exit(bgep->genlock); return (0); } /* * bge_m_promisc() -- set or reset promiscuous mode on the board * * Program the hardware to enable/disable promiscuous and/or * receive-all-multicast modes. */ static int bge_m_promisc(void *arg, boolean_t on) { bge_t *bgep = arg; BGE_TRACE(("bge_m_promisc_set($%p, %d)", arg, on)); /* * Store MAC layer specified mode and pass to chip layer to update h/w */ mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } bgep->promisc = on; #ifdef BGE_IPMI_ASF if (bge_chip_sync(bgep, B_TRUE) == DDI_FAILURE) { #else if (bge_chip_sync(bgep) == DDI_FAILURE) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } BGE_DEBUG(("bge_m_promisc_set($%p) done", arg)); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (EIO); } mutex_exit(bgep->genlock); return (0); } /*ARGSUSED*/ static boolean_t bge_m_getcapab(void *arg, mac_capab_t cap, void *cap_data) { bge_t *bgep = arg; switch (cap) { case MAC_CAPAB_HCKSUM: { uint32_t *txflags = cap_data; *txflags = HCKSUM_INET_FULL_V4 | HCKSUM_IPHDRCKSUM; break; } case MAC_CAPAB_POLL: /* * There's nothing for us to fill in, simply returning * B_TRUE stating that we support polling is sufficient. */ break; case MAC_CAPAB_MULTIADDRESS: { multiaddress_capab_t *mmacp = cap_data; mutex_enter(bgep->genlock); /* * The number of MAC addresses made available by * this capability is one less than the total as * the primary address in slot 0 is counted in * the total. */ mmacp->maddr_naddr = bgep->unicst_addr_total - 1; mmacp->maddr_naddrfree = bgep->unicst_addr_avail; /* No multiple factory addresses, set mma_flag to 0 */ mmacp->maddr_flag = 0; mmacp->maddr_handle = bgep; mmacp->maddr_add = bge_m_unicst_add; mmacp->maddr_remove = bge_m_unicst_remove; mmacp->maddr_modify = bge_m_unicst_modify; mmacp->maddr_get = bge_m_unicst_get; mmacp->maddr_reserve = NULL; mutex_exit(bgep->genlock); break; } default: return (B_FALSE); } return (B_TRUE); } /* * Loopback ioctl code */ static lb_property_t loopmodes[] = { { normal, "normal", BGE_LOOP_NONE }, { external, "1000Mbps", BGE_LOOP_EXTERNAL_1000 }, { external, "100Mbps", BGE_LOOP_EXTERNAL_100 }, { external, "10Mbps", BGE_LOOP_EXTERNAL_10 }, { internal, "PHY", BGE_LOOP_INTERNAL_PHY }, { internal, "MAC", BGE_LOOP_INTERNAL_MAC } }; static enum ioc_reply bge_set_loop_mode(bge_t *bgep, uint32_t mode) { /* * If the mode isn't being changed, there's nothing to do ... */ if (mode == bgep->param_loop_mode) return (IOC_ACK); /* * Validate the requested mode and prepare a suitable message * to explain the link down/up cycle that the change will * probably induce ... */ switch (mode) { default: return (IOC_INVAL); case BGE_LOOP_NONE: case BGE_LOOP_EXTERNAL_1000: case BGE_LOOP_EXTERNAL_100: case BGE_LOOP_EXTERNAL_10: case BGE_LOOP_INTERNAL_PHY: case BGE_LOOP_INTERNAL_MAC: break; } /* * All OK; tell the caller to reprogram * the PHY and/or MAC for the new mode ... */ bgep->param_loop_mode = mode; return (IOC_RESTART_ACK); } static enum ioc_reply bge_loop_ioctl(bge_t *bgep, queue_t *wq, mblk_t *mp, struct iocblk *iocp) { lb_info_sz_t *lbsp; lb_property_t *lbpp; uint32_t *lbmp; int cmd; _NOTE(ARGUNUSED(wq)) /* * Validate format of ioctl */ if (mp->b_cont == NULL) return (IOC_INVAL); cmd = iocp->ioc_cmd; switch (cmd) { default: /* NOTREACHED */ bge_error(bgep, "bge_loop_ioctl: invalid cmd 0x%x", cmd); return (IOC_INVAL); case LB_GET_INFO_SIZE: if (iocp->ioc_count != sizeof (lb_info_sz_t)) return (IOC_INVAL); lbsp = (void *)mp->b_cont->b_rptr; *lbsp = sizeof (loopmodes); return (IOC_REPLY); case LB_GET_INFO: if (iocp->ioc_count != sizeof (loopmodes)) return (IOC_INVAL); lbpp = (void *)mp->b_cont->b_rptr; bcopy(loopmodes, lbpp, sizeof (loopmodes)); return (IOC_REPLY); case LB_GET_MODE: if (iocp->ioc_count != sizeof (uint32_t)) return (IOC_INVAL); lbmp = (void *)mp->b_cont->b_rptr; *lbmp = bgep->param_loop_mode; return (IOC_REPLY); case LB_SET_MODE: if (iocp->ioc_count != sizeof (uint32_t)) return (IOC_INVAL); lbmp = (void *)mp->b_cont->b_rptr; return (bge_set_loop_mode(bgep, *lbmp)); } } /* * Specific bge IOCTLs, the gld module handles the generic ones. */ static void bge_m_ioctl(void *arg, queue_t *wq, mblk_t *mp) { bge_t *bgep = arg; struct iocblk *iocp; enum ioc_reply status; boolean_t need_privilege; int err; int cmd; /* * Validate the command before bothering with the mutex ... */ iocp = (void *)mp->b_rptr; iocp->ioc_error = 0; need_privilege = B_TRUE; cmd = iocp->ioc_cmd; switch (cmd) { default: miocnak(wq, mp, 0, EINVAL); return; case BGE_MII_READ: case BGE_MII_WRITE: case BGE_SEE_READ: case BGE_SEE_WRITE: case BGE_FLASH_READ: case BGE_FLASH_WRITE: case BGE_DIAG: case BGE_PEEK: case BGE_POKE: case BGE_PHY_RESET: case BGE_SOFT_RESET: case BGE_HARD_RESET: break; case LB_GET_INFO_SIZE: case LB_GET_INFO: case LB_GET_MODE: need_privilege = B_FALSE; /* FALLTHRU */ case LB_SET_MODE: break; } if (need_privilege) { /* * Check for specific net_config privilege on Solaris 10+. */ err = secpolicy_net_config(iocp->ioc_cr, B_FALSE); if (err != 0) { miocnak(wq, mp, 0, err); return; } } mutex_enter(bgep->genlock); if (!(bgep->progress & PROGRESS_INTR)) { /* can happen during autorecovery */ mutex_exit(bgep->genlock); miocnak(wq, mp, 0, EIO); return; } switch (cmd) { default: _NOTE(NOTREACHED) status = IOC_INVAL; break; case BGE_MII_READ: case BGE_MII_WRITE: case BGE_SEE_READ: case BGE_SEE_WRITE: case BGE_FLASH_READ: case BGE_FLASH_WRITE: case BGE_DIAG: case BGE_PEEK: case BGE_POKE: case BGE_PHY_RESET: case BGE_SOFT_RESET: case BGE_HARD_RESET: status = bge_chip_ioctl(bgep, wq, mp, iocp); break; case LB_GET_INFO_SIZE: case LB_GET_INFO: case LB_GET_MODE: case LB_SET_MODE: status = bge_loop_ioctl(bgep, wq, mp, iocp); break; } /* * Do we need to reprogram the PHY and/or the MAC? * Do it now, while we still have the mutex. * * Note: update the PHY first, 'cos it controls the * speed/duplex parameters that the MAC code uses. */ switch (status) { case IOC_RESTART_REPLY: case IOC_RESTART_ACK: if (bge_reprogram(bgep) == IOC_INVAL) status = IOC_INVAL; break; } if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); status = IOC_INVAL; } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); status = IOC_INVAL; } mutex_exit(bgep->genlock); /* * Finally, decide how to reply */ switch (status) { default: case IOC_INVAL: /* * Error, reply with a NAK and EINVAL or the specified error */ miocnak(wq, mp, 0, iocp->ioc_error == 0 ? EINVAL : iocp->ioc_error); break; case IOC_DONE: /* * OK, reply already sent */ break; case IOC_RESTART_ACK: case IOC_ACK: /* * OK, reply with an ACK */ miocack(wq, mp, 0, 0); break; case IOC_RESTART_REPLY: case IOC_REPLY: /* * OK, send prepared reply as ACK or NAK */ mp->b_datap->db_type = iocp->ioc_error == 0 ? M_IOCACK : M_IOCNAK; qreply(wq, mp); break; } } static void bge_resources_add(bge_t *bgep, time_t time, uint_t pkt_cnt) { recv_ring_t *rrp; mac_rx_fifo_t mrf; int ring; /* * Register Rx rings as resources and save mac * resource id for future reference */ mrf.mrf_type = MAC_RX_FIFO; mrf.mrf_blank = bge_chip_blank; mrf.mrf_arg = (void *)bgep; mrf.mrf_normal_blank_time = time; mrf.mrf_normal_pkt_count = pkt_cnt; for (ring = 0; ring < bgep->chipid.rx_rings; ring++) { rrp = &bgep->recv[ring]; rrp->handle = mac_resource_add(bgep->mh, (mac_resource_t *)&mrf); } } static void bge_m_resources(void *arg) { bge_t *bgep = arg; mutex_enter(bgep->genlock); bge_resources_add(bgep, bgep->chipid.rx_ticks_norm, bgep->chipid.rx_count_norm); mutex_exit(bgep->genlock); } /* * ========== Per-instance setup/teardown code ========== */ #undef BGE_DBG #define BGE_DBG BGE_DBG_INIT /* debug flag for this code */ /* * Allocate an area of memory and a DMA handle for accessing it */ static int bge_alloc_dma_mem(bge_t *bgep, size_t memsize, ddi_device_acc_attr_t *attr_p, uint_t dma_flags, dma_area_t *dma_p) { caddr_t va; int err; BGE_TRACE(("bge_alloc_dma_mem($%p, %ld, $%p, 0x%x, $%p)", (void *)bgep, memsize, attr_p, dma_flags, dma_p)); /* * Allocate handle */ err = ddi_dma_alloc_handle(bgep->devinfo, &dma_attr, DDI_DMA_DONTWAIT, NULL, &dma_p->dma_hdl); if (err != DDI_SUCCESS) return (DDI_FAILURE); /* * Allocate memory */ err = ddi_dma_mem_alloc(dma_p->dma_hdl, memsize, attr_p, dma_flags, DDI_DMA_DONTWAIT, NULL, &va, &dma_p->alength, &dma_p->acc_hdl); if (err != DDI_SUCCESS) return (DDI_FAILURE); /* * Bind the two together */ dma_p->mem_va = va; err = ddi_dma_addr_bind_handle(dma_p->dma_hdl, NULL, va, dma_p->alength, dma_flags, DDI_DMA_DONTWAIT, NULL, &dma_p->cookie, &dma_p->ncookies); BGE_DEBUG(("bge_alloc_dma_mem(): bind %d bytes; err %d, %d cookies", dma_p->alength, err, dma_p->ncookies)); if (err != DDI_DMA_MAPPED || dma_p->ncookies != 1) return (DDI_FAILURE); dma_p->nslots = ~0U; dma_p->size = ~0U; dma_p->token = ~0U; dma_p->offset = 0; return (DDI_SUCCESS); } /* * Free one allocated area of DMAable memory */ static void bge_free_dma_mem(dma_area_t *dma_p) { if (dma_p->dma_hdl != NULL) { if (dma_p->ncookies) { (void) ddi_dma_unbind_handle(dma_p->dma_hdl); dma_p->ncookies = 0; } ddi_dma_free_handle(&dma_p->dma_hdl); dma_p->dma_hdl = NULL; } if (dma_p->acc_hdl != NULL) { ddi_dma_mem_free(&dma_p->acc_hdl); dma_p->acc_hdl = NULL; } } /* * Utility routine to carve a slice off a chunk of allocated memory, * updating the chunk descriptor accordingly. The size of the slice * is given by the product of the and parameters. */ static void bge_slice_chunk(dma_area_t *slice, dma_area_t *chunk, uint32_t qty, uint32_t size) { static uint32_t sequence = 0xbcd5704a; size_t totsize; totsize = qty*size; ASSERT(totsize <= chunk->alength); *slice = *chunk; slice->nslots = qty; slice->size = size; slice->alength = totsize; slice->token = ++sequence; chunk->mem_va = (caddr_t)chunk->mem_va + totsize; chunk->alength -= totsize; chunk->offset += totsize; chunk->cookie.dmac_laddress += totsize; chunk->cookie.dmac_size -= totsize; } /* * Initialise the specified Receive Producer (Buffer) Ring, using * the information in the descriptors that it contains * to set up all the other fields. This routine should be called * only once for each ring. */ static void bge_init_buff_ring(bge_t *bgep, uint64_t ring) { buff_ring_t *brp; bge_status_t *bsp; sw_rbd_t *srbdp; dma_area_t pbuf; uint32_t bufsize; uint32_t nslots; uint32_t slot; uint32_t split; static bge_regno_t nic_ring_addrs[BGE_BUFF_RINGS_MAX] = { NIC_MEM_SHADOW_BUFF_STD, NIC_MEM_SHADOW_BUFF_JUMBO, NIC_MEM_SHADOW_BUFF_MINI }; static bge_regno_t mailbox_regs[BGE_BUFF_RINGS_MAX] = { RECV_STD_PROD_INDEX_REG, RECV_JUMBO_PROD_INDEX_REG, RECV_MINI_PROD_INDEX_REG }; static bge_regno_t buff_cons_xref[BGE_BUFF_RINGS_MAX] = { STATUS_STD_BUFF_CONS_INDEX, STATUS_JUMBO_BUFF_CONS_INDEX, STATUS_MINI_BUFF_CONS_INDEX }; BGE_TRACE(("bge_init_buff_ring($%p, %d)", (void *)bgep, ring)); brp = &bgep->buff[ring]; nslots = brp->desc.nslots; ASSERT(brp->buf[0].nslots == nslots/BGE_SPLIT); bufsize = brp->buf[0].size; /* * Set up the copy of the h/w RCB * * Note: unlike Send & Receive Return Rings, (where the max_len * field holds the number of slots), in a Receive Buffer Ring * this field indicates the size of each buffer in the ring. */ brp->hw_rcb.host_ring_addr = brp->desc.cookie.dmac_laddress; brp->hw_rcb.max_len = (uint16_t)bufsize; brp->hw_rcb.flags = nslots > 0 ? 0 : RCB_FLAG_RING_DISABLED; brp->hw_rcb.nic_ring_addr = nic_ring_addrs[ring]; /* * Other one-off initialisation of per-ring data */ brp->bgep = bgep; bsp = DMA_VPTR(bgep->status_block); brp->cons_index_p = &bsp->buff_cons_index[buff_cons_xref[ring]]; brp->chip_mbx_reg = mailbox_regs[ring]; mutex_init(brp->rf_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); /* * Allocate the array of s/w Receive Buffer Descriptors */ srbdp = kmem_zalloc(nslots*sizeof (*srbdp), KM_SLEEP); brp->sw_rbds = srbdp; /* * Now initialise each array element once and for all */ for (split = 0; split < BGE_SPLIT; ++split) { pbuf = brp->buf[split]; for (slot = 0; slot < nslots/BGE_SPLIT; ++srbdp, ++slot) bge_slice_chunk(&srbdp->pbuf, &pbuf, 1, bufsize); ASSERT(pbuf.alength == 0); } } /* * Clean up initialisation done above before the memory is freed */ static void bge_fini_buff_ring(bge_t *bgep, uint64_t ring) { buff_ring_t *brp; sw_rbd_t *srbdp; BGE_TRACE(("bge_fini_buff_ring($%p, %d)", (void *)bgep, ring)); brp = &bgep->buff[ring]; srbdp = brp->sw_rbds; kmem_free(srbdp, brp->desc.nslots*sizeof (*srbdp)); mutex_destroy(brp->rf_lock); } /* * Initialise the specified Receive (Return) Ring, using the * information in the descriptors that it contains * to set up all the other fields. This routine should be called * only once for each ring. */ static void bge_init_recv_ring(bge_t *bgep, uint64_t ring) { recv_ring_t *rrp; bge_status_t *bsp; uint32_t nslots; BGE_TRACE(("bge_init_recv_ring($%p, %d)", (void *)bgep, ring)); /* * The chip architecture requires that receive return rings have * 512 or 1024 or 2048 elements per ring. See 570X-PG108-R page 103. */ rrp = &bgep->recv[ring]; nslots = rrp->desc.nslots; ASSERT(nslots == 0 || nslots == 512 || nslots == 1024 || nslots == 2048); /* * Set up the copy of the h/w RCB */ rrp->hw_rcb.host_ring_addr = rrp->desc.cookie.dmac_laddress; rrp->hw_rcb.max_len = (uint16_t)nslots; rrp->hw_rcb.flags = nslots > 0 ? 0 : RCB_FLAG_RING_DISABLED; rrp->hw_rcb.nic_ring_addr = 0; /* * Other one-off initialisation of per-ring data */ rrp->bgep = bgep; bsp = DMA_VPTR(bgep->status_block); rrp->prod_index_p = RECV_INDEX_P(bsp, ring); rrp->chip_mbx_reg = RECV_RING_CONS_INDEX_REG(ring); mutex_init(rrp->rx_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); } /* * Clean up initialisation done above before the memory is freed */ static void bge_fini_recv_ring(bge_t *bgep, uint64_t ring) { recv_ring_t *rrp; BGE_TRACE(("bge_fini_recv_ring($%p, %d)", (void *)bgep, ring)); rrp = &bgep->recv[ring]; if (rrp->rx_softint) ddi_remove_softintr(rrp->rx_softint); mutex_destroy(rrp->rx_lock); } /* * Initialise the specified Send Ring, using the information in the * descriptors that it contains to set up all the other * fields. This routine should be called only once for each ring. */ static void bge_init_send_ring(bge_t *bgep, uint64_t ring) { send_ring_t *srp; bge_status_t *bsp; sw_sbd_t *ssbdp; dma_area_t desc; dma_area_t pbuf; uint32_t nslots; uint32_t slot; uint32_t split; sw_txbuf_t *txbuf; BGE_TRACE(("bge_init_send_ring($%p, %d)", (void *)bgep, ring)); /* * The chip architecture requires that host-based send rings * have 512 elements per ring. See 570X-PG102-R page 56. */ srp = &bgep->send[ring]; nslots = srp->desc.nslots; ASSERT(nslots == 0 || nslots == 512); /* * Set up the copy of the h/w RCB */ srp->hw_rcb.host_ring_addr = srp->desc.cookie.dmac_laddress; srp->hw_rcb.max_len = (uint16_t)nslots; srp->hw_rcb.flags = nslots > 0 ? 0 : RCB_FLAG_RING_DISABLED; srp->hw_rcb.nic_ring_addr = NIC_MEM_SHADOW_SEND_RING(ring, nslots); /* * Other one-off initialisation of per-ring data */ srp->bgep = bgep; bsp = DMA_VPTR(bgep->status_block); srp->cons_index_p = SEND_INDEX_P(bsp, ring); srp->chip_mbx_reg = SEND_RING_HOST_INDEX_REG(ring); mutex_init(srp->tx_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); mutex_init(srp->txbuf_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); mutex_init(srp->freetxbuf_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); mutex_init(srp->tc_lock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); if (nslots == 0) return; /* * Allocate the array of s/w Send Buffer Descriptors */ ssbdp = kmem_zalloc(nslots*sizeof (*ssbdp), KM_SLEEP); txbuf = kmem_zalloc(BGE_SEND_BUF_MAX*sizeof (*txbuf), KM_SLEEP); srp->txbuf_head = kmem_zalloc(BGE_SEND_BUF_MAX*sizeof (bge_queue_item_t), KM_SLEEP); srp->pktp = kmem_zalloc(BGE_SEND_BUF_MAX*sizeof (send_pkt_t), KM_SLEEP); srp->sw_sbds = ssbdp; srp->txbuf = txbuf; srp->tx_buffers = BGE_SEND_BUF_NUM; srp->tx_buffers_low = srp->tx_buffers / 4; if (bgep->chipid.snd_buff_size > BGE_SEND_BUFF_SIZE_DEFAULT) srp->tx_array_max = BGE_SEND_BUF_ARRAY_JUMBO; else srp->tx_array_max = BGE_SEND_BUF_ARRAY; srp->tx_array = 1; /* * Chunk tx desc area */ desc = srp->desc; for (slot = 0; slot < nslots; ++ssbdp, ++slot) { bge_slice_chunk(&ssbdp->desc, &desc, 1, sizeof (bge_sbd_t)); } ASSERT(desc.alength == 0); /* * Chunk tx buffer area */ for (split = 0; split < BGE_SPLIT; ++split) { pbuf = srp->buf[0][split]; for (slot = 0; slot < BGE_SEND_BUF_NUM/BGE_SPLIT; ++slot) { bge_slice_chunk(&txbuf->buf, &pbuf, 1, bgep->chipid.snd_buff_size); txbuf++; } ASSERT(pbuf.alength == 0); } } /* * Clean up initialisation done above before the memory is freed */ static void bge_fini_send_ring(bge_t *bgep, uint64_t ring) { send_ring_t *srp; uint32_t array; uint32_t split; uint32_t nslots; BGE_TRACE(("bge_fini_send_ring($%p, %d)", (void *)bgep, ring)); srp = &bgep->send[ring]; mutex_destroy(srp->tc_lock); mutex_destroy(srp->freetxbuf_lock); mutex_destroy(srp->txbuf_lock); mutex_destroy(srp->tx_lock); nslots = srp->desc.nslots; if (nslots == 0) return; for (array = 1; array < srp->tx_array; ++array) for (split = 0; split < BGE_SPLIT; ++split) bge_free_dma_mem(&srp->buf[array][split]); kmem_free(srp->sw_sbds, nslots*sizeof (*srp->sw_sbds)); kmem_free(srp->txbuf_head, BGE_SEND_BUF_MAX*sizeof (*srp->txbuf_head)); kmem_free(srp->txbuf, BGE_SEND_BUF_MAX*sizeof (*srp->txbuf)); kmem_free(srp->pktp, BGE_SEND_BUF_MAX*sizeof (*srp->pktp)); srp->sw_sbds = NULL; srp->txbuf_head = NULL; srp->txbuf = NULL; srp->pktp = NULL; } /* * Initialise all transmit, receive, and buffer rings. */ void bge_init_rings(bge_t *bgep) { uint32_t ring; BGE_TRACE(("bge_init_rings($%p)", (void *)bgep)); /* * Perform one-off initialisation of each ring ... */ for (ring = 0; ring < BGE_SEND_RINGS_MAX; ++ring) bge_init_send_ring(bgep, ring); for (ring = 0; ring < BGE_RECV_RINGS_MAX; ++ring) bge_init_recv_ring(bgep, ring); for (ring = 0; ring < BGE_BUFF_RINGS_MAX; ++ring) bge_init_buff_ring(bgep, ring); } /* * Undo the work of bge_init_rings() above before the memory is freed */ void bge_fini_rings(bge_t *bgep) { uint32_t ring; BGE_TRACE(("bge_fini_rings($%p)", (void *)bgep)); for (ring = 0; ring < BGE_BUFF_RINGS_MAX; ++ring) bge_fini_buff_ring(bgep, ring); for (ring = 0; ring < BGE_RECV_RINGS_MAX; ++ring) bge_fini_recv_ring(bgep, ring); for (ring = 0; ring < BGE_SEND_RINGS_MAX; ++ring) bge_fini_send_ring(bgep, ring); } /* * Called from the bge_m_stop() to free the tx buffers which are * allocated from the tx process. */ void bge_free_txbuf_arrays(send_ring_t *srp) { uint32_t array; uint32_t split; ASSERT(mutex_owned(srp->tx_lock)); /* * Free the extra tx buffer DMA area */ for (array = 1; array < srp->tx_array; ++array) for (split = 0; split < BGE_SPLIT; ++split) bge_free_dma_mem(&srp->buf[array][split]); /* * Restore initial tx buffer numbers */ srp->tx_array = 1; srp->tx_buffers = BGE_SEND_BUF_NUM; srp->tx_buffers_low = srp->tx_buffers / 4; srp->tx_flow = 0; bzero(srp->pktp, BGE_SEND_BUF_MAX * sizeof (*srp->pktp)); } /* * Called from tx process to allocate more tx buffers */ bge_queue_item_t * bge_alloc_txbuf_array(bge_t *bgep, send_ring_t *srp) { bge_queue_t *txbuf_queue; bge_queue_item_t *txbuf_item_last; bge_queue_item_t *txbuf_item; bge_queue_item_t *txbuf_item_rtn; sw_txbuf_t *txbuf; dma_area_t area; size_t txbuffsize; uint32_t slot; uint32_t array; uint32_t split; uint32_t err; ASSERT(mutex_owned(srp->tx_lock)); array = srp->tx_array; if (array >= srp->tx_array_max) return (NULL); /* * Allocate memory & handles for TX buffers */ txbuffsize = BGE_SEND_BUF_NUM*bgep->chipid.snd_buff_size; ASSERT((txbuffsize % BGE_SPLIT) == 0); for (split = 0; split < BGE_SPLIT; ++split) { err = bge_alloc_dma_mem(bgep, txbuffsize/BGE_SPLIT, &bge_data_accattr, DDI_DMA_WRITE | BGE_DMA_MODE, &srp->buf[array][split]); if (err != DDI_SUCCESS) { /* Free the last already allocated OK chunks */ for (slot = 0; slot <= split; ++slot) bge_free_dma_mem(&srp->buf[array][slot]); srp->tx_alloc_fail++; return (NULL); } } /* * Chunk tx buffer area */ txbuf = srp->txbuf + array*BGE_SEND_BUF_NUM; for (split = 0; split < BGE_SPLIT; ++split) { area = srp->buf[array][split]; for (slot = 0; slot < BGE_SEND_BUF_NUM/BGE_SPLIT; ++slot) { bge_slice_chunk(&txbuf->buf, &area, 1, bgep->chipid.snd_buff_size); txbuf++; } } /* * Add above buffers to the tx buffer pop queue */ txbuf_item = srp->txbuf_head + array*BGE_SEND_BUF_NUM; txbuf = srp->txbuf + array*BGE_SEND_BUF_NUM; txbuf_item_last = NULL; for (slot = 0; slot < BGE_SEND_BUF_NUM; ++slot) { txbuf_item->item = txbuf; txbuf_item->next = txbuf_item_last; txbuf_item_last = txbuf_item; txbuf++; txbuf_item++; } txbuf_item = srp->txbuf_head + array*BGE_SEND_BUF_NUM; txbuf_item_rtn = txbuf_item; txbuf_item++; txbuf_queue = srp->txbuf_pop_queue; mutex_enter(txbuf_queue->lock); txbuf_item->next = txbuf_queue->head; txbuf_queue->head = txbuf_item_last; txbuf_queue->count += BGE_SEND_BUF_NUM - 1; mutex_exit(txbuf_queue->lock); srp->tx_array++; srp->tx_buffers += BGE_SEND_BUF_NUM; srp->tx_buffers_low = srp->tx_buffers / 4; return (txbuf_item_rtn); } /* * This function allocates all the transmit and receive buffers * and descriptors, in four chunks. */ int bge_alloc_bufs(bge_t *bgep) { dma_area_t area; size_t rxbuffsize; size_t txbuffsize; size_t rxbuffdescsize; size_t rxdescsize; size_t txdescsize; uint32_t ring; uint32_t rx_rings = bgep->chipid.rx_rings; uint32_t tx_rings = bgep->chipid.tx_rings; int split; int err; BGE_TRACE(("bge_alloc_bufs($%p)", (void *)bgep)); rxbuffsize = BGE_STD_SLOTS_USED*bgep->chipid.std_buf_size; rxbuffsize += bgep->chipid.jumbo_slots*bgep->chipid.recv_jumbo_size; rxbuffsize += BGE_MINI_SLOTS_USED*BGE_MINI_BUFF_SIZE; txbuffsize = BGE_SEND_BUF_NUM*bgep->chipid.snd_buff_size; txbuffsize *= tx_rings; rxdescsize = rx_rings*bgep->chipid.recv_slots; rxdescsize *= sizeof (bge_rbd_t); rxbuffdescsize = BGE_STD_SLOTS_USED; rxbuffdescsize += bgep->chipid.jumbo_slots; rxbuffdescsize += BGE_MINI_SLOTS_USED; rxbuffdescsize *= sizeof (bge_rbd_t); txdescsize = tx_rings*BGE_SEND_SLOTS_USED; txdescsize *= sizeof (bge_sbd_t); txdescsize += sizeof (bge_statistics_t); txdescsize += sizeof (bge_status_t); txdescsize += BGE_STATUS_PADDING; /* * Enable PCI relaxed ordering only for RX/TX data buffers */ if (bge_relaxed_ordering) dma_attr.dma_attr_flags |= DDI_DMA_RELAXED_ORDERING; /* * Allocate memory & handles for RX buffers */ ASSERT((rxbuffsize % BGE_SPLIT) == 0); for (split = 0; split < BGE_SPLIT; ++split) { err = bge_alloc_dma_mem(bgep, rxbuffsize/BGE_SPLIT, &bge_data_accattr, DDI_DMA_READ | BGE_DMA_MODE, &bgep->rx_buff[split]); if (err != DDI_SUCCESS) return (DDI_FAILURE); } /* * Allocate memory & handles for TX buffers */ ASSERT((txbuffsize % BGE_SPLIT) == 0); for (split = 0; split < BGE_SPLIT; ++split) { err = bge_alloc_dma_mem(bgep, txbuffsize/BGE_SPLIT, &bge_data_accattr, DDI_DMA_WRITE | BGE_DMA_MODE, &bgep->tx_buff[split]); if (err != DDI_SUCCESS) return (DDI_FAILURE); } dma_attr.dma_attr_flags &= ~DDI_DMA_RELAXED_ORDERING; /* * Allocate memory & handles for receive return rings */ ASSERT((rxdescsize % rx_rings) == 0); for (split = 0; split < rx_rings; ++split) { err = bge_alloc_dma_mem(bgep, rxdescsize/rx_rings, &bge_desc_accattr, DDI_DMA_RDWR | DDI_DMA_CONSISTENT, &bgep->rx_desc[split]); if (err != DDI_SUCCESS) return (DDI_FAILURE); } /* * Allocate memory & handles for buffer (producer) descriptor rings */ err = bge_alloc_dma_mem(bgep, rxbuffdescsize, &bge_desc_accattr, DDI_DMA_RDWR | DDI_DMA_CONSISTENT, &bgep->rx_desc[split]); if (err != DDI_SUCCESS) return (DDI_FAILURE); /* * Allocate memory & handles for TX descriptor rings, * status block, and statistics area */ err = bge_alloc_dma_mem(bgep, txdescsize, &bge_desc_accattr, DDI_DMA_RDWR | DDI_DMA_CONSISTENT, &bgep->tx_desc); if (err != DDI_SUCCESS) return (DDI_FAILURE); /* * Now carve up each of the allocated areas ... */ for (split = 0; split < BGE_SPLIT; ++split) { area = bgep->rx_buff[split]; bge_slice_chunk(&bgep->buff[BGE_STD_BUFF_RING].buf[split], &area, BGE_STD_SLOTS_USED/BGE_SPLIT, bgep->chipid.std_buf_size); bge_slice_chunk(&bgep->buff[BGE_JUMBO_BUFF_RING].buf[split], &area, bgep->chipid.jumbo_slots/BGE_SPLIT, bgep->chipid.recv_jumbo_size); bge_slice_chunk(&bgep->buff[BGE_MINI_BUFF_RING].buf[split], &area, BGE_MINI_SLOTS_USED/BGE_SPLIT, BGE_MINI_BUFF_SIZE); } for (split = 0; split < BGE_SPLIT; ++split) { area = bgep->tx_buff[split]; for (ring = 0; ring < tx_rings; ++ring) bge_slice_chunk(&bgep->send[ring].buf[0][split], &area, BGE_SEND_BUF_NUM/BGE_SPLIT, bgep->chipid.snd_buff_size); for (; ring < BGE_SEND_RINGS_MAX; ++ring) bge_slice_chunk(&bgep->send[ring].buf[0][split], &area, 0, bgep->chipid.snd_buff_size); } for (ring = 0; ring < rx_rings; ++ring) bge_slice_chunk(&bgep->recv[ring].desc, &bgep->rx_desc[ring], bgep->chipid.recv_slots, sizeof (bge_rbd_t)); area = bgep->rx_desc[rx_rings]; for (; ring < BGE_RECV_RINGS_MAX; ++ring) bge_slice_chunk(&bgep->recv[ring].desc, &area, 0, sizeof (bge_rbd_t)); bge_slice_chunk(&bgep->buff[BGE_STD_BUFF_RING].desc, &area, BGE_STD_SLOTS_USED, sizeof (bge_rbd_t)); bge_slice_chunk(&bgep->buff[BGE_JUMBO_BUFF_RING].desc, &area, bgep->chipid.jumbo_slots, sizeof (bge_rbd_t)); bge_slice_chunk(&bgep->buff[BGE_MINI_BUFF_RING].desc, &area, BGE_MINI_SLOTS_USED, sizeof (bge_rbd_t)); ASSERT(area.alength == 0); area = bgep->tx_desc; for (ring = 0; ring < tx_rings; ++ring) bge_slice_chunk(&bgep->send[ring].desc, &area, BGE_SEND_SLOTS_USED, sizeof (bge_sbd_t)); for (; ring < BGE_SEND_RINGS_MAX; ++ring) bge_slice_chunk(&bgep->send[ring].desc, &area, 0, sizeof (bge_sbd_t)); bge_slice_chunk(&bgep->statistics, &area, 1, sizeof (bge_statistics_t)); bge_slice_chunk(&bgep->status_block, &area, 1, sizeof (bge_status_t)); ASSERT(area.alength == BGE_STATUS_PADDING); DMA_ZERO(bgep->status_block); return (DDI_SUCCESS); } /* * This routine frees the transmit and receive buffers and descriptors. * Make sure the chip is stopped before calling it! */ void bge_free_bufs(bge_t *bgep) { int split; BGE_TRACE(("bge_free_bufs($%p)", (void *)bgep)); bge_free_dma_mem(&bgep->tx_desc); for (split = 0; split < BGE_RECV_RINGS_SPLIT; ++split) bge_free_dma_mem(&bgep->rx_desc[split]); for (split = 0; split < BGE_SPLIT; ++split) bge_free_dma_mem(&bgep->tx_buff[split]); for (split = 0; split < BGE_SPLIT; ++split) bge_free_dma_mem(&bgep->rx_buff[split]); } /* * Determine (initial) MAC address ("BIA") to use for this interface */ static void bge_find_mac_address(bge_t *bgep, chip_id_t *cidp) { struct ether_addr sysaddr; char propbuf[8]; /* "true" or "false", plus NUL */ uchar_t *bytes; int *ints; uint_t nelts; int err; BGE_TRACE(("bge_find_mac_address($%p)", (void *)bgep)); BGE_DEBUG(("bge_find_mac_address: hw_mac_addr %012llx, => %s (%sset)", cidp->hw_mac_addr, ether_sprintf((void *)cidp->vendor_addr.addr), cidp->vendor_addr.set ? "" : "not ")); /* * The "vendor's factory-set address" may already have * been extracted from the chip, but if the property * "local-mac-address" is set we use that instead. It * will normally be set by OBP, but it could also be * specified in a .conf file(!) * * There doesn't seem to be a way to define byte-array * properties in a .conf, so we check whether it looks * like an array of 6 ints instead. * * Then, we check whether it looks like an array of 6 * bytes (which it should, if OBP set it). If we can't * make sense of it either way, we'll ignore it. */ err = ddi_prop_lookup_int_array(DDI_DEV_T_ANY, bgep->devinfo, DDI_PROP_DONTPASS, localmac_propname, &ints, &nelts); if (err == DDI_PROP_SUCCESS) { if (nelts == ETHERADDRL) { while (nelts--) cidp->vendor_addr.addr[nelts] = ints[nelts]; cidp->vendor_addr.set = B_TRUE; } ddi_prop_free(ints); } err = ddi_prop_lookup_byte_array(DDI_DEV_T_ANY, bgep->devinfo, DDI_PROP_DONTPASS, localmac_propname, &bytes, &nelts); if (err == DDI_PROP_SUCCESS) { if (nelts == ETHERADDRL) { while (nelts--) cidp->vendor_addr.addr[nelts] = bytes[nelts]; cidp->vendor_addr.set = B_TRUE; } ddi_prop_free(bytes); } BGE_DEBUG(("bge_find_mac_address: +local %s (%sset)", ether_sprintf((void *)cidp->vendor_addr.addr), cidp->vendor_addr.set ? "" : "not ")); /* * Look up the OBP property "local-mac-address?". Note that even * though its value is a string (which should be "true" or "false"), * it can't be decoded by ddi_prop_lookup_string(9F). So, we zero * the buffer first and then fetch the property as an untyped array; * this may or may not include a final NUL, but since there will * always be one left at the end of the buffer we can now treat it * as a string anyway. */ nelts = sizeof (propbuf); bzero(propbuf, nelts--); err = ddi_getlongprop_buf(DDI_DEV_T_ANY, bgep->devinfo, DDI_PROP_CANSLEEP, localmac_boolname, propbuf, (int *)&nelts); /* * Now, if the address still isn't set from the hardware (SEEPROM) * or the OBP or .conf property, OR if the user has foolishly set * 'local-mac-address? = false', use "the system address" instead * (but only if it's non-null i.e. has been set from the IDPROM). */ if (cidp->vendor_addr.set == B_FALSE || strcmp(propbuf, "false") == 0) if (localetheraddr(NULL, &sysaddr) != 0) { ethaddr_copy(&sysaddr, cidp->vendor_addr.addr); cidp->vendor_addr.set = B_TRUE; } BGE_DEBUG(("bge_find_mac_address: +system %s (%sset)", ether_sprintf((void *)cidp->vendor_addr.addr), cidp->vendor_addr.set ? "" : "not ")); /* * Finally(!), if there's a valid "mac-address" property (created * if we netbooted from this interface), we must use this instead * of any of the above to ensure that the NFS/install server doesn't * get confused by the address changing as Solaris takes over! */ err = ddi_prop_lookup_byte_array(DDI_DEV_T_ANY, bgep->devinfo, DDI_PROP_DONTPASS, macaddr_propname, &bytes, &nelts); if (err == DDI_PROP_SUCCESS) { if (nelts == ETHERADDRL) { while (nelts--) cidp->vendor_addr.addr[nelts] = bytes[nelts]; cidp->vendor_addr.set = B_TRUE; } ddi_prop_free(bytes); } BGE_DEBUG(("bge_find_mac_address: =final %s (%sset)", ether_sprintf((void *)cidp->vendor_addr.addr), cidp->vendor_addr.set ? "" : "not ")); } /*ARGSUSED*/ int bge_check_acc_handle(bge_t *bgep, ddi_acc_handle_t handle) { ddi_fm_error_t de; ddi_fm_acc_err_get(handle, &de, DDI_FME_VERSION); ddi_fm_acc_err_clear(handle, DDI_FME_VERSION); return (de.fme_status); } /*ARGSUSED*/ int bge_check_dma_handle(bge_t *bgep, ddi_dma_handle_t handle) { ddi_fm_error_t de; ASSERT(bgep->progress & PROGRESS_BUFS); ddi_fm_dma_err_get(handle, &de, DDI_FME_VERSION); return (de.fme_status); } /* * The IO fault service error handling callback function */ /*ARGSUSED*/ static int bge_fm_error_cb(dev_info_t *dip, ddi_fm_error_t *err, const void *impl_data) { /* * as the driver can always deal with an error in any dma or * access handle, we can just return the fme_status value. */ pci_ereport_post(dip, err, NULL); return (err->fme_status); } static void bge_fm_init(bge_t *bgep) { ddi_iblock_cookie_t iblk; /* Only register with IO Fault Services if we have some capability */ if (bgep->fm_capabilities) { bge_reg_accattr.devacc_attr_access = DDI_FLAGERR_ACC; bge_desc_accattr.devacc_attr_access = DDI_FLAGERR_ACC; dma_attr.dma_attr_flags = DDI_DMA_FLAGERR; /* Register capabilities with IO Fault Services */ ddi_fm_init(bgep->devinfo, &bgep->fm_capabilities, &iblk); /* * Initialize pci ereport capabilities if ereport capable */ if (DDI_FM_EREPORT_CAP(bgep->fm_capabilities) || DDI_FM_ERRCB_CAP(bgep->fm_capabilities)) pci_ereport_setup(bgep->devinfo); /* * Register error callback if error callback capable */ if (DDI_FM_ERRCB_CAP(bgep->fm_capabilities)) ddi_fm_handler_register(bgep->devinfo, bge_fm_error_cb, (void*) bgep); } else { /* * These fields have to be cleared of FMA if there are no * FMA capabilities at runtime. */ bge_reg_accattr.devacc_attr_access = DDI_DEFAULT_ACC; bge_desc_accattr.devacc_attr_access = DDI_DEFAULT_ACC; dma_attr.dma_attr_flags = 0; } } static void bge_fm_fini(bge_t *bgep) { /* Only unregister FMA capabilities if we registered some */ if (bgep->fm_capabilities) { /* * Release any resources allocated by pci_ereport_setup() */ if (DDI_FM_EREPORT_CAP(bgep->fm_capabilities) || DDI_FM_ERRCB_CAP(bgep->fm_capabilities)) pci_ereport_teardown(bgep->devinfo); /* * Un-register error callback if error callback capable */ if (DDI_FM_ERRCB_CAP(bgep->fm_capabilities)) ddi_fm_handler_unregister(bgep->devinfo); /* Unregister from IO Fault Services */ ddi_fm_fini(bgep->devinfo); } } static void #ifdef BGE_IPMI_ASF bge_unattach(bge_t *bgep, uint_t asf_mode) #else bge_unattach(bge_t *bgep) #endif { BGE_TRACE(("bge_unattach($%p)", (void *)bgep)); /* * Flag that no more activity may be initiated */ bgep->progress &= ~PROGRESS_READY; /* * Quiesce the PHY and MAC (leave it reset but still powered). * Clean up and free all BGE data structures */ if (bgep->periodic_id != NULL) { ddi_periodic_delete(bgep->periodic_id); bgep->periodic_id = NULL; } if (bgep->progress & PROGRESS_KSTATS) bge_fini_kstats(bgep); if (bgep->progress & PROGRESS_PHY) bge_phys_reset(bgep); if (bgep->progress & PROGRESS_HWINT) { mutex_enter(bgep->genlock); #ifdef BGE_IPMI_ASF if (bge_chip_reset(bgep, B_FALSE, asf_mode) != DDI_SUCCESS) #else if (bge_chip_reset(bgep, B_FALSE) != DDI_SUCCESS) #endif ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { /* * This register has been overlaid. We restore its * initial value here. */ bge_nic_put32(bgep, BGE_NIC_DATA_SIG_ADDR, BGE_NIC_DATA_SIG); } #endif if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); mutex_exit(bgep->genlock); } if (bgep->progress & PROGRESS_INTR) { bge_intr_disable(bgep); bge_fini_rings(bgep); } if (bgep->progress & PROGRESS_HWINT) { bge_rem_intrs(bgep); rw_destroy(bgep->errlock); mutex_destroy(bgep->softintrlock); mutex_destroy(bgep->genlock); } if (bgep->progress & PROGRESS_FACTOTUM) ddi_remove_softintr(bgep->factotum_id); if (bgep->progress & PROGRESS_RESCHED) ddi_remove_softintr(bgep->drain_id); if (bgep->progress & PROGRESS_BUFS) bge_free_bufs(bgep); if (bgep->progress & PROGRESS_REGS) ddi_regs_map_free(&bgep->io_handle); if (bgep->progress & PROGRESS_CFG) pci_config_teardown(&bgep->cfg_handle); bge_fm_fini(bgep); ddi_remove_minor_node(bgep->devinfo, NULL); kmem_free(bgep->pstats, sizeof (bge_statistics_reg_t)); kmem_free(bgep, sizeof (*bgep)); } static int bge_resume(dev_info_t *devinfo) { bge_t *bgep; /* Our private data */ chip_id_t *cidp; chip_id_t chipid; bgep = ddi_get_driver_private(devinfo); if (bgep == NULL) return (DDI_FAILURE); /* * Refuse to resume if the data structures aren't consistent */ if (bgep->devinfo != devinfo) return (DDI_FAILURE); #ifdef BGE_IPMI_ASF /* * Power management hasn't been supported in BGE now. If you * want to implement it, please add the ASF/IPMI related * code here. */ #endif /* * Read chip ID & set up config space command register(s) * Refuse to resume if the chip has changed its identity! */ cidp = &bgep->chipid; mutex_enter(bgep->genlock); bge_chip_cfg_init(bgep, &chipid, B_FALSE); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); return (DDI_FAILURE); } mutex_exit(bgep->genlock); if (chipid.vendor != cidp->vendor) return (DDI_FAILURE); if (chipid.device != cidp->device) return (DDI_FAILURE); if (chipid.revision != cidp->revision) return (DDI_FAILURE); if (chipid.asic_rev != cidp->asic_rev) return (DDI_FAILURE); /* * All OK, reinitialise h/w & kick off GLD scheduling */ mutex_enter(bgep->genlock); if (bge_restart(bgep, B_TRUE) != DDI_SUCCESS) { (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); return (DDI_FAILURE); } if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); return (DDI_FAILURE); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); return (DDI_FAILURE); } mutex_exit(bgep->genlock); return (DDI_SUCCESS); } /* * attach(9E) -- Attach a device to the system * * Called once for each board successfully probed. */ static int bge_attach(dev_info_t *devinfo, ddi_attach_cmd_t cmd) { bge_t *bgep; /* Our private data */ mac_register_t *macp; chip_id_t *cidp; caddr_t regs; int instance; int err; int intr_types; #ifdef BGE_IPMI_ASF uint32_t mhcrValue; #ifdef __sparc uint16_t value16; #endif #ifdef BGE_NETCONSOLE int retval; #endif #endif instance = ddi_get_instance(devinfo); BGE_GTRACE(("bge_attach($%p, %d) instance %d", (void *)devinfo, cmd, instance)); BGE_BRKPT(NULL, "bge_attach"); switch (cmd) { default: return (DDI_FAILURE); case DDI_RESUME: return (bge_resume(devinfo)); case DDI_ATTACH: break; } bgep = kmem_zalloc(sizeof (*bgep), KM_SLEEP); bgep->pstats = kmem_zalloc(sizeof (bge_statistics_reg_t), KM_SLEEP); ddi_set_driver_private(devinfo, bgep); bgep->bge_guard = BGE_GUARD; bgep->devinfo = devinfo; bgep->param_drain_max = 64; bgep->param_msi_cnt = 0; bgep->param_loop_mode = 0; /* * Initialize more fields in BGE private data */ bgep->debug = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, debug_propname, bge_debug); (void) snprintf(bgep->ifname, sizeof (bgep->ifname), "%s%d", BGE_DRIVER_NAME, instance); /* * Initialize for fma support */ bgep->fm_capabilities = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, fm_cap, DDI_FM_EREPORT_CAPABLE | DDI_FM_ACCCHK_CAPABLE | DDI_FM_DMACHK_CAPABLE | DDI_FM_ERRCB_CAPABLE); BGE_DEBUG(("bgep->fm_capabilities = %d", bgep->fm_capabilities)); bge_fm_init(bgep); /* * Look up the IOMMU's page size for DVMA mappings (must be * a power of 2) and convert to a mask. This can be used to * determine whether a message buffer crosses a page boundary. * Note: in 2s complement binary notation, if X is a power of * 2, then -X has the representation "11...1100...00". */ bgep->pagemask = dvma_pagesize(devinfo); ASSERT(ddi_ffs(bgep->pagemask) == ddi_fls(bgep->pagemask)); bgep->pagemask = -bgep->pagemask; /* * Map config space registers * Read chip ID & set up config space command register(s) * * Note: this leaves the chip accessible by Memory Space * accesses, but with interrupts and Bus Mastering off. * This should ensure that nothing untoward will happen * if it has been left active by the (net-)bootloader. * We'll re-enable Bus Mastering once we've reset the chip, * and allow interrupts only when everything else is set up. */ err = pci_config_setup(devinfo, &bgep->cfg_handle); #ifdef BGE_IPMI_ASF #ifdef __sparc value16 = pci_config_get16(bgep->cfg_handle, PCI_CONF_COMM); value16 = value16 | (PCI_COMM_MAE | PCI_COMM_ME); pci_config_put16(bgep->cfg_handle, PCI_CONF_COMM, value16); mhcrValue = MHCR_ENABLE_INDIRECT_ACCESS | MHCR_ENABLE_TAGGED_STATUS_MODE | MHCR_MASK_INTERRUPT_MODE | MHCR_MASK_PCI_INT_OUTPUT | MHCR_CLEAR_INTERRUPT_INTA | MHCR_ENABLE_ENDIAN_WORD_SWAP | MHCR_ENABLE_ENDIAN_BYTE_SWAP; pci_config_put32(bgep->cfg_handle, PCI_CONF_BGE_MHCR, mhcrValue); bge_ind_put32(bgep, MEMORY_ARBITER_MODE_REG, bge_ind_get32(bgep, MEMORY_ARBITER_MODE_REG) | MEMORY_ARBITER_ENABLE); #else mhcrValue = pci_config_get32(bgep->cfg_handle, PCI_CONF_BGE_MHCR); #endif if (mhcrValue & MHCR_ENABLE_ENDIAN_WORD_SWAP) { bgep->asf_wordswapped = B_TRUE; } else { bgep->asf_wordswapped = B_FALSE; } bge_asf_get_config(bgep); #endif if (err != DDI_SUCCESS) { bge_problem(bgep, "pci_config_setup() failed"); goto attach_fail; } bgep->progress |= PROGRESS_CFG; cidp = &bgep->chipid; bzero(cidp, sizeof (*cidp)); bge_chip_cfg_init(bgep, cidp, B_FALSE); if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); goto attach_fail; } #ifdef BGE_IPMI_ASF if (DEVICE_5721_SERIES_CHIPSETS(bgep) || DEVICE_5714_SERIES_CHIPSETS(bgep)) { bgep->asf_newhandshake = B_TRUE; } else { bgep->asf_newhandshake = B_FALSE; } #endif /* * Update those parts of the chip ID derived from volatile * registers with the values seen by OBP (in case the chip * has been reset externally and therefore lost them). */ cidp->subven = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, subven_propname, cidp->subven); cidp->subdev = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, subdev_propname, cidp->subdev); cidp->clsize = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, clsize_propname, cidp->clsize); cidp->latency = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, latency_propname, cidp->latency); cidp->rx_rings = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, rxrings_propname, cidp->rx_rings); cidp->tx_rings = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, txrings_propname, cidp->tx_rings); if (bge_jumbo_enable == B_TRUE) { cidp->default_mtu = ddi_prop_get_int(DDI_DEV_T_ANY, devinfo, DDI_PROP_DONTPASS, default_mtu, BGE_DEFAULT_MTU); if ((cidp->default_mtu < BGE_DEFAULT_MTU)|| (cidp->default_mtu > BGE_MAXIMUM_MTU)) { cidp->default_mtu = BGE_DEFAULT_MTU; } } /* * Map operating registers */ err = ddi_regs_map_setup(devinfo, BGE_PCI_OPREGS_RNUMBER, ®s, 0, 0, &bge_reg_accattr, &bgep->io_handle); if (err != DDI_SUCCESS) { bge_problem(bgep, "ddi_regs_map_setup() failed"); goto attach_fail; } bgep->io_regs = regs; bgep->progress |= PROGRESS_REGS; /* * Characterise the device, so we know its requirements. * Then allocate the appropriate TX and RX descriptors & buffers. */ if (bge_chip_id_init(bgep) == EIO) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); goto attach_fail; } err = bge_alloc_bufs(bgep); if (err != DDI_SUCCESS) { bge_problem(bgep, "DMA buffer allocation failed"); goto attach_fail; } bgep->progress |= PROGRESS_BUFS; /* * Add the softint handlers: * * Both of these handlers are used to avoid restrictions on the * context and/or mutexes required for some operations. In * particular, the hardware interrupt handler and its subfunctions * can detect a number of conditions that we don't want to handle * in that context or with that set of mutexes held. So, these * softints are triggered instead: * * the softint is triggered if we have previously * had to refuse to send a packet because of resource shortage * (we've run out of transmit buffers), but the send completion * interrupt handler has now detected that more buffers have * become available. * * the is triggered if the h/w interrupt handler * sees the or bits in the status * block. It's also triggered periodically to poll the link * state, just in case we aren't getting link status change * interrupts ... */ err = ddi_add_softintr(devinfo, DDI_SOFTINT_LOW, &bgep->drain_id, NULL, NULL, bge_send_drain, (caddr_t)bgep); if (err != DDI_SUCCESS) { bge_problem(bgep, "ddi_add_softintr() failed"); goto attach_fail; } bgep->progress |= PROGRESS_RESCHED; err = ddi_add_softintr(devinfo, DDI_SOFTINT_LOW, &bgep->factotum_id, NULL, NULL, bge_chip_factotum, (caddr_t)bgep); if (err != DDI_SUCCESS) { bge_problem(bgep, "ddi_add_softintr() failed"); goto attach_fail; } bgep->progress |= PROGRESS_FACTOTUM; /* Get supported interrupt types */ if (ddi_intr_get_supported_types(devinfo, &intr_types) != DDI_SUCCESS) { bge_error(bgep, "ddi_intr_get_supported_types failed\n"); goto attach_fail; } BGE_DEBUG(("%s: ddi_intr_get_supported_types() returned: %x", bgep->ifname, intr_types)); if ((intr_types & DDI_INTR_TYPE_MSI) && bgep->chipid.msi_enabled) { if (bge_add_intrs(bgep, DDI_INTR_TYPE_MSI) != DDI_SUCCESS) { bge_error(bgep, "MSI registration failed, " "trying FIXED interrupt type\n"); } else { BGE_DEBUG(("%s: Using MSI interrupt type", bgep->ifname)); bgep->intr_type = DDI_INTR_TYPE_MSI; bgep->progress |= PROGRESS_HWINT; } } if (!(bgep->progress & PROGRESS_HWINT) && (intr_types & DDI_INTR_TYPE_FIXED)) { if (bge_add_intrs(bgep, DDI_INTR_TYPE_FIXED) != DDI_SUCCESS) { bge_error(bgep, "FIXED interrupt " "registration failed\n"); goto attach_fail; } BGE_DEBUG(("%s: Using FIXED interrupt type", bgep->ifname)); bgep->intr_type = DDI_INTR_TYPE_FIXED; bgep->progress |= PROGRESS_HWINT; } if (!(bgep->progress & PROGRESS_HWINT)) { bge_error(bgep, "No interrupts registered\n"); goto attach_fail; } /* * Note that interrupts are not enabled yet as * mutex locks are not initialized. Initialize mutex locks. */ mutex_init(bgep->genlock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); mutex_init(bgep->softintrlock, NULL, MUTEX_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); rw_init(bgep->errlock, NULL, RW_DRIVER, DDI_INTR_PRI(bgep->intr_pri)); /* * Initialize rings. */ bge_init_rings(bgep); /* * Now that mutex locks are initialized, enable interrupts. */ bge_intr_enable(bgep); bgep->progress |= PROGRESS_INTR; /* * Initialise link state variables * Stop, reset & reinitialise the chip. * Initialise the (internal) PHY. */ bgep->link_state = LINK_STATE_UNKNOWN; mutex_enter(bgep->genlock); /* * Reset chip & rings to initial state; also reset address * filtering, promiscuity, loopback mode. */ #ifdef BGE_IPMI_ASF #ifdef BGE_NETCONSOLE if (bge_reset(bgep, ASF_MODE_INIT) != DDI_SUCCESS) { #else if (bge_reset(bgep, ASF_MODE_SHUTDOWN) != DDI_SUCCESS) { #endif #else if (bge_reset(bgep) != DDI_SUCCESS) { #endif (void) bge_check_acc_handle(bgep, bgep->cfg_handle); (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); goto attach_fail; } #ifdef BGE_IPMI_ASF if (bgep->asf_enabled) { bgep->asf_status = ASF_STAT_RUN_INIT; } #endif bzero(bgep->mcast_hash, sizeof (bgep->mcast_hash)); bzero(bgep->mcast_refs, sizeof (bgep->mcast_refs)); bgep->promisc = B_FALSE; bgep->param_loop_mode = BGE_LOOP_NONE; if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); goto attach_fail; } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); mutex_exit(bgep->genlock); goto attach_fail; } mutex_exit(bgep->genlock); if (bge_phys_init(bgep) == EIO) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_LOST); goto attach_fail; } bgep->progress |= PROGRESS_PHY; /* * initialize NDD-tweakable parameters */ if (bge_nd_init(bgep)) { bge_problem(bgep, "bge_nd_init() failed"); goto attach_fail; } bgep->progress |= PROGRESS_NDD; /* * Create & initialise named kstats */ bge_init_kstats(bgep, instance); bgep->progress |= PROGRESS_KSTATS; /* * Determine whether to override the chip's own MAC address */ bge_find_mac_address(bgep, cidp); ethaddr_copy(cidp->vendor_addr.addr, bgep->curr_addr[0].addr); bgep->curr_addr[0].set = B_TRUE; bgep->unicst_addr_total = MAC_ADDRESS_REGS_MAX; /* * Address available is one less than MAX * as primary address is not advertised * as a multiple MAC address. */ bgep->unicst_addr_avail = MAC_ADDRESS_REGS_MAX - 1; if ((macp = mac_alloc(MAC_VERSION)) == NULL) goto attach_fail; macp->m_type_ident = MAC_PLUGIN_IDENT_ETHER; macp->m_driver = bgep; macp->m_dip = devinfo; macp->m_src_addr = bgep->curr_addr[0].addr; macp->m_callbacks = &bge_m_callbacks; macp->m_min_sdu = 0; macp->m_max_sdu = cidp->ethmax_size - sizeof (struct ether_header); macp->m_margin = VLAN_TAGSZ; macp->m_priv_props = bge_priv_prop; macp->m_priv_prop_count = BGE_MAX_PRIV_PROPS; /* * Finally, we're ready to register ourselves with the MAC layer * interface; if this succeeds, we're all ready to start() */ err = mac_register(macp, &bgep->mh); mac_free(macp); if (err != 0) goto attach_fail; /* * Register a periodical handler. * bge_chip_cyclic() is invoked in kernel context. */ bgep->periodic_id = ddi_periodic_add(bge_chip_cyclic, bgep, BGE_CYCLIC_PERIOD, DDI_IPL_0); bgep->progress |= PROGRESS_READY; ASSERT(bgep->bge_guard == BGE_GUARD); #ifdef BGE_IPMI_ASF #ifdef BGE_NETCONSOLE if (bgep->asf_enabled) { mutex_enter(bgep->genlock); retval = bge_chip_start(bgep, B_TRUE); mutex_exit(bgep->genlock); if (retval != DDI_SUCCESS) goto attach_fail; } #endif #endif return (DDI_SUCCESS); attach_fail: #ifdef BGE_IPMI_ASF bge_unattach(bgep, ASF_MODE_SHUTDOWN); #else bge_unattach(bgep); #endif return (DDI_FAILURE); } /* * bge_suspend() -- suspend transmit/receive for powerdown */ static int bge_suspend(bge_t *bgep) { /* * Stop processing and idle (powerdown) the PHY ... */ mutex_enter(bgep->genlock); #ifdef BGE_IPMI_ASF /* * Power management hasn't been supported in BGE now. If you * want to implement it, please add the ASF/IPMI related * code here. */ #endif bge_stop(bgep); if (bge_phys_idle(bgep) != DDI_SUCCESS) { (void) bge_check_acc_handle(bgep, bgep->io_handle); ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (DDI_FAILURE); } if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); mutex_exit(bgep->genlock); return (DDI_FAILURE); } mutex_exit(bgep->genlock); return (DDI_SUCCESS); } /* * detach(9E) -- Detach a device from the system */ static int bge_detach(dev_info_t *devinfo, ddi_detach_cmd_t cmd) { bge_t *bgep; #ifdef BGE_IPMI_ASF uint_t asf_mode; asf_mode = ASF_MODE_NONE; #endif BGE_GTRACE(("bge_detach($%p, %d)", (void *)devinfo, cmd)); bgep = ddi_get_driver_private(devinfo); switch (cmd) { default: return (DDI_FAILURE); case DDI_SUSPEND: return (bge_suspend(bgep)); case DDI_DETACH: break; } #ifdef BGE_IPMI_ASF mutex_enter(bgep->genlock); if (bgep->asf_enabled && ((bgep->asf_status == ASF_STAT_RUN) || (bgep->asf_status == ASF_STAT_RUN_INIT))) { bge_asf_update_status(bgep); if (bgep->asf_status == ASF_STAT_RUN) { bge_asf_stop_timer(bgep); } bgep->asf_status = ASF_STAT_STOP; bge_asf_pre_reset_operations(bgep, BGE_SHUTDOWN_RESET); if (bgep->asf_pseudostop) { bge_chip_stop(bgep, B_FALSE); bgep->bge_mac_state = BGE_MAC_STOPPED; bgep->asf_pseudostop = B_FALSE; } asf_mode = ASF_MODE_POST_SHUTDOWN; if (bge_check_acc_handle(bgep, bgep->cfg_handle) != DDI_FM_OK) ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); if (bge_check_acc_handle(bgep, bgep->io_handle) != DDI_FM_OK) ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_UNAFFECTED); } mutex_exit(bgep->genlock); #endif /* * Unregister from the GLD subsystem. This can fail, in * particular if there are DLPI style-2 streams still open - * in which case we just return failure without shutting * down chip operations. */ if (mac_unregister(bgep->mh) != 0) return (DDI_FAILURE); /* * All activity stopped, so we can clean up & exit */ #ifdef BGE_IPMI_ASF bge_unattach(bgep, asf_mode); #else bge_unattach(bgep); #endif return (DDI_SUCCESS); } /* * ========== Module Loading Data & Entry Points ========== */ #undef BGE_DBG #define BGE_DBG BGE_DBG_INIT /* debug flag for this code */ DDI_DEFINE_STREAM_OPS(bge_dev_ops, nulldev, nulldev, bge_attach, bge_detach, nodev, NULL, D_MP, NULL); static struct modldrv bge_modldrv = { &mod_driverops, /* Type of module. This one is a driver */ bge_ident, /* short description */ &bge_dev_ops /* driver specific ops */ }; static struct modlinkage modlinkage = { MODREV_1, (void *)&bge_modldrv, NULL }; int _info(struct modinfo *modinfop) { return (mod_info(&modlinkage, modinfop)); } int _init(void) { int status; mac_init_ops(&bge_dev_ops, "bge"); status = mod_install(&modlinkage); if (status == DDI_SUCCESS) mutex_init(bge_log_mutex, NULL, MUTEX_DRIVER, NULL); else mac_fini_ops(&bge_dev_ops); return (status); } int _fini(void) { int status; status = mod_remove(&modlinkage); if (status == DDI_SUCCESS) { mac_fini_ops(&bge_dev_ops); mutex_destroy(bge_log_mutex); } return (status); } /* * bge_add_intrs: * * Register FIXED or MSI interrupts. */ static int bge_add_intrs(bge_t *bgep, int intr_type) { dev_info_t *dip = bgep->devinfo; int avail, actual, intr_size, count = 0; int i, flag, ret; BGE_DEBUG(("bge_add_intrs($%p, 0x%x)", (void *)bgep, intr_type)); /* Get number of interrupts */ ret = ddi_intr_get_nintrs(dip, intr_type, &count); if ((ret != DDI_SUCCESS) || (count == 0)) { bge_error(bgep, "ddi_intr_get_nintrs() failure, ret: %d, " "count: %d", ret, count); return (DDI_FAILURE); } /* Get number of available interrupts */ ret = ddi_intr_get_navail(dip, intr_type, &avail); if ((ret != DDI_SUCCESS) || (avail == 0)) { bge_error(bgep, "ddi_intr_get_navail() failure, " "ret: %d, avail: %d\n", ret, avail); return (DDI_FAILURE); } if (avail < count) { BGE_DEBUG(("%s: nintrs() returned %d, navail returned %d", bgep->ifname, count, avail)); } /* * BGE hardware generates only single MSI even though it claims * to support multiple MSIs. So, hard code MSI count value to 1. */ if (intr_type == DDI_INTR_TYPE_MSI) { count = 1; flag = DDI_INTR_ALLOC_STRICT; } else { flag = DDI_INTR_ALLOC_NORMAL; } /* Allocate an array of interrupt handles */ intr_size = count * sizeof (ddi_intr_handle_t); bgep->htable = kmem_alloc(intr_size, KM_SLEEP); /* Call ddi_intr_alloc() */ ret = ddi_intr_alloc(dip, bgep->htable, intr_type, 0, count, &actual, flag); if ((ret != DDI_SUCCESS) || (actual == 0)) { bge_error(bgep, "ddi_intr_alloc() failed %d\n", ret); kmem_free(bgep->htable, intr_size); return (DDI_FAILURE); } if (actual < count) { BGE_DEBUG(("%s: Requested: %d, Received: %d", bgep->ifname, count, actual)); } bgep->intr_cnt = actual; /* * Get priority for first msi, assume remaining are all the same */ if ((ret = ddi_intr_get_pri(bgep->htable[0], &bgep->intr_pri)) != DDI_SUCCESS) { bge_error(bgep, "ddi_intr_get_pri() failed %d\n", ret); /* Free already allocated intr */ for (i = 0; i < actual; i++) { (void) ddi_intr_free(bgep->htable[i]); } kmem_free(bgep->htable, intr_size); return (DDI_FAILURE); } /* Call ddi_intr_add_handler() */ for (i = 0; i < actual; i++) { if ((ret = ddi_intr_add_handler(bgep->htable[i], bge_intr, (caddr_t)bgep, (caddr_t)(uintptr_t)i)) != DDI_SUCCESS) { bge_error(bgep, "ddi_intr_add_handler() " "failed %d\n", ret); /* Free already allocated intr */ for (i = 0; i < actual; i++) { (void) ddi_intr_free(bgep->htable[i]); } kmem_free(bgep->htable, intr_size); return (DDI_FAILURE); } } if ((ret = ddi_intr_get_cap(bgep->htable[0], &bgep->intr_cap)) != DDI_SUCCESS) { bge_error(bgep, "ddi_intr_get_cap() failed %d\n", ret); for (i = 0; i < actual; i++) { (void) ddi_intr_remove_handler(bgep->htable[i]); (void) ddi_intr_free(bgep->htable[i]); } kmem_free(bgep->htable, intr_size); return (DDI_FAILURE); } return (DDI_SUCCESS); } /* * bge_rem_intrs: * * Unregister FIXED or MSI interrupts */ static void bge_rem_intrs(bge_t *bgep) { int i; BGE_DEBUG(("bge_rem_intrs($%p)", (void *)bgep)); /* Call ddi_intr_remove_handler() */ for (i = 0; i < bgep->intr_cnt; i++) { (void) ddi_intr_remove_handler(bgep->htable[i]); (void) ddi_intr_free(bgep->htable[i]); } kmem_free(bgep->htable, bgep->intr_cnt * sizeof (ddi_intr_handle_t)); } void bge_intr_enable(bge_t *bgep) { int i; if (bgep->intr_cap & DDI_INTR_FLAG_BLOCK) { /* Call ddi_intr_block_enable() for MSI interrupts */ (void) ddi_intr_block_enable(bgep->htable, bgep->intr_cnt); } else { /* Call ddi_intr_enable for MSI or FIXED interrupts */ for (i = 0; i < bgep->intr_cnt; i++) { (void) ddi_intr_enable(bgep->htable[i]); } } } void bge_intr_disable(bge_t *bgep) { int i; if (bgep->intr_cap & DDI_INTR_FLAG_BLOCK) { /* Call ddi_intr_block_disable() */ (void) ddi_intr_block_disable(bgep->htable, bgep->intr_cnt); } else { for (i = 0; i < bgep->intr_cnt; i++) { (void) ddi_intr_disable(bgep->htable[i]); } } } int bge_reprogram(bge_t *bgep) { int status = 0; ASSERT(mutex_owned(bgep->genlock)); if (bge_phys_update(bgep) != DDI_SUCCESS) { ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); status = IOC_INVAL; } #ifdef BGE_IPMI_ASF if (bge_chip_sync(bgep, B_TRUE) == DDI_FAILURE) { #else if (bge_chip_sync(bgep) == DDI_FAILURE) { #endif ddi_fm_service_impact(bgep->devinfo, DDI_SERVICE_DEGRADED); status = IOC_INVAL; } if (bgep->intr_type == DDI_INTR_TYPE_MSI) bge_chip_msi_trig(bgep); return (status); }