/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2006 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #ifndef _RGE_HW_H #define _RGE_HW_H #pragma ident "%Z%%M% %I% %E% SMI" #ifdef __cplusplus extern "C" { #endif #include /* * First section: * Identification of the various Realtek GigE chips */ /* * Driver support device */ #define VENDOR_ID_REALTECK 0x10EC #define DEVICE_ID_8169 0x8169 #define DEVICE_ID_8110 0x8110 #define DEVICE_ID_8168 0x8168 #define DEVICE_ID_8111 0x8111 #define RGE_REGISTER_MAX 0x0100 /* * Second section: * Offsets of important registers & definitions for bits therein */ /* * MAC address register, initial value is autoloaded from the * EEPROM EthernetID field */ #define ID_0_REG 0x0000 #define ID_1_REG 0x0001 #define ID_2_REG 0x0002 #define ID_3_REG 0x0003 #define ID_4_REG 0x0004 #define ID_5_REG 0x0005 /* * Multicast register */ #define MULTICAST_0_REG 0x0008 #define MULTICAST_1_REG 0x0009 #define MULTICAST_2_REG 0x000a #define MULTICAST_3_REG 0x000b #define MULTICAST_4_REG 0x000c #define MULTICAST_5_REG 0x000d #define MULTICAST_6_REG 0x000e #define MULTICAST_7_REG 0x000f #define RGE_MCAST_NUM 8 /* total 8 registers: MAR0 - MAR7 */ /* * Dump Tally Counter Command register */ #define DUMP_COUNTER_REG_0 0x0010 #define DUMP_COUNTER_REG_RESV 0x00000037 #define DUMP_START 0x00000008 #define DUMP_COUNTER_REG_1 0x0014 /* * Register for start address of transmit descriptors */ #define NORMAL_TX_RING_ADDR_LO_REG 0x0020 #define NORMAL_TX_RING_ADDR_HI_REG 0x0024 #define HIGH_TX_RING_ADDR_LO_REG 0x0028 #define HIGH_TX_RING_ADDR_HI_REG 0x002c /* * Commond register */ #define RT_COMMAND_REG 0x0037 #define RT_COMMAND_RESV 0xe3 #define RT_COMMAND_RESET 0x10 #define RT_COMMAND_RX_ENABLE 0x08 #define RT_COMMAND_TX_ENABLE 0x04 /* * Transmit priority polling register */ #define TX_RINGS_POLL_REG 0x0038 #define HIGH_TX_RING_POLL 0x80 #define NORMAL_TX_RING_POLL 0x40 #define FORCE_SW_INT 0x01 /* * Interrupt mask & status register */ #define INT_MASK_REG 0x003c #define INT_STATUS_REG 0x003e #define SYS_ERR_INT 0x8000 #define TIME_OUT_INT 0x4000 #define SW_INT 0x0100 #define NO_TXDESC_INT 0x0080 #define RX_FIFO_OVERFLOW_INT 0x0040 #define LINK_CHANGE_INT 0x0020 #define NO_RXDESC_INT 0x0010 #define TX_ERR_INT 0x0008 #define TX_OK_INT 0x0004 #define RX_ERR_INT 0x0002 #define RX_OK_INT 0x0001 #define INT_REG_RESV 0x3e00 #define INT_MASK_ALL 0xffff #define INT_MASK_NONE 0x0000 #define RGE_RX_INT (RX_OK_INT | RX_ERR_INT | \ NO_RXDESC_INT) #define RGE_INT_MASK (RGE_RX_INT | LINK_CHANGE_INT) /* * Transmit configuration register */ #define TX_CONFIG_REG 0x0040 #define TX_CONFIG_REG_RESV 0x8070f8ff #define HW_VERSION_ID_0 0x7c000000 #define INTER_FRAME_GAP_BITS 0x03080000 #define TX_INTERFRAME_GAP_802_3 0x03000000 #define HW_VERSION_ID_1 0x00800000 #define MAC_LOOPBACK_ENABLE 0x00060000 #define CRC_APPEND_ENABLE 0x00010000 #define TX_DMA_BURST_BITS 0x00000700 #define TX_DMA_BURST_UNLIMIT 0x00000700 #define TX_DMA_BURST_1024B 0x00000600 #define TX_DMA_BURST_512B 0x00000500 #define TX_DMA_BURST_256B 0x00000400 #define TX_DMA_BURST_128B 0x00000300 #define TX_DMA_BURST_64B 0x00000200 #define TX_DMA_BURST_32B 0x00000100 #define TX_DMA_BURST_16B 0x00000000 #define MAC_VER_8169 0x00000000 #define MAC_VER_8169S_D 0x00800000 #define MAC_VER_8169S_E 0x04000000 #define MAC_VER_8169SB 0x10000000 #define MAC_VER_8168 0x20000000 #define MAC_VER_8168B_B 0x30000000 #define MAC_VER_8168B_C 0x38000000 #define TX_CONFIG_DEFAULT (TX_INTERFRAME_GAP_802_3 | \ TX_DMA_BURST_1024B) /* * Receive configuration register */ #define RX_CONFIG_REG 0x0044 #define RX_CONFIG_REG_RESV 0xfffe1880 #define RX_RER8_ENABLE 0x00010000 #define RX_FIFO_THRESHOLD_BITS 0x0000e000 #define RX_FIFO_THRESHOLD_NONE 0x0000e000 #define RX_FIFO_THRESHOLD_1024B 0x0000c000 #define RX_FIFO_THRESHOLD_512B 0x0000a000 #define RX_FIFO_THRESHOLD_256B 0x00008000 #define RX_FIFO_THRESHOLD_128B 0x00006000 #define RX_FIFO_THRESHOLD_64B 0x00004000 #define RX_DMA_BURST_BITS 0x00000700 #define RX_DMA_BURST_UNLIMITED 0x00000700 #define RX_DMA_BURST_1024B 0x00000600 #define RX_DMA_BURST_512B 0x00000500 #define RX_DMA_BURST_256B 0x00000400 #define RX_DMA_BURST_128B 0x00000300 #define RX_DMA_BURST_64B 0x00000200 #define RX_EEPROM_9356 0x00000040 #define RX_ACCEPT_ERR_PKT 0x00000020 #define RX_ACCEPT_RUNT_PKT 0x00000010 #define RX_ACCEPT_BROADCAST_PKT 0x000000008 #define RX_ACCEPT_MULTICAST_PKT 0x000000004 #define RX_ACCEPT_MAC_MATCH_PKT 0x000000002 #define RX_ACCEPT_ALL_PKT 0x000000001 #define RX_CONFIG_DEFAULT (RX_FIFO_THRESHOLD_NONE | \ RX_DMA_BURST_1024B | \ RX_ACCEPT_BROADCAST_PKT | \ RX_ACCEPT_MULTICAST_PKT | \ RX_ACCEPT_MAC_MATCH_PKT) /* * Timer count register */ #define TIMER_COUNT_REG 0x0048 /* * Missed packet counter: indicates the number of packets * discarded due to Rx FIFO overflow */ #define RX_PKT_MISS_COUNT_REG 0x004c /* * 93c46(93c56) commond register: */ #define RT_93c46_COMMOND_REG 0x0050 #define RT_93c46_MODE_BITS 0xc0 #define RT_93c46_MODE_NORMAL 0x00 #define RT_93c46_MODE_AUTOLOAD 0x40 #define RT_93c46_MODE_PROGRAM 0x80 #define RT_93c46_MODE_CONFIG 0xc0 #define RT_93c46_EECS 0x08 #define RT_93c46_EESK 0x04 #define RT_93c46_EEDI 0x02 #define RT_93c46_EEDO 0x01 /* * Configuration registers */ #define RT_CONFIG_0_REG 0x0051 #define RT_CONFIG_1_REG 0x0052 #define RT_CONFIG_2_REG 0x0053 #define RT_CONFIG_3_REG 0x0054 #define RT_CONFIG_4_REG 0x0055 #define RT_CONFIG_5_REG 0x0056 /* * Timer interrupt register */ #define TIMER_INT_REG 0x0058 #define TIMER_INT_NONE 0x00000000 /* * PHY access register */ #define PHY_ACCESS_REG 0x0060 #define PHY_ACCESS_WR_FLAG 0x80000000 #define PHY_ACCESS_REG_BITS 0x001f0000 #define PHY_ACCESS_DATA_BITS 0x0000ffff #define PHY_DATA_MASK 0xffff #define PHY_REG_MASK 0x1f #define PHY_REG_SHIFT 16 /* * CSI data register (for PCIE chipset) */ #define RT_CSI_DATA_REG 0x0064 /* * CSI access register (for PCIE chipset) */ #define RT_CSI_ACCESS_REG 0x0068 /* * PHY status register */ #define PHY_STATUS_REG 0x006c #define PHY_STATUS_TBI 0x80 #define PHY_STATUS_TX_FLOW 0x40 #define PHY_STATUS_RX_FLOW 0x20 #define PHY_STATUS_1000MF 0x10 #define PHY_STATUS_100M 0x08 #define PHY_STATUS_10M 0x04 #define PHY_STATUS_LINK_UP 0x02 #define PHY_STATUS_DUPLEX_FULL 0x01 #define RGE_SPEED_1000M 1000 #define RGE_SPEED_100M 100 #define RGE_SPEED_10M 10 #define RGE_SPEED_UNKNOWN 0 /* * EPHY access register (for PCIE chipset) */ #define EPHY_ACCESS_REG 0x0080 #define EPHY_ACCESS_WR_FLAG 0x80000000 #define EPHY_ACCESS_REG_BITS 0x001f0000 #define EPHY_ACCESS_DATA_BITS 0x0000ffff #define EPHY_DATA_MASK 0xffff #define EPHY_REG_MASK 0x1f #define EPHY_REG_SHIFT 16 /* * Receive packet maximum size register * -- the maximum rx size supported is (16K - 1) bytes */ #define RX_MAX_PKTSIZE_REG 0x00da #define RX_PKTSIZE_JUMBO 0x1bfa /* 7K bytes */ #define RX_PKTSIZE_STD 0x05fa /* 1530 bytes */ /* * C+ command register */ #define CPLUS_COMMAND_REG 0x00e0 #define CPLUS_RESERVE 0xfd87 #define CPLUS_BIT14 0x4000 #define CPLUS_BIG_ENDIAN 0x0400 #define RX_VLAN_DETAG 0x0040 #define RX_CKSM_OFFLOAD 0x0020 #define DUAL_PCI_CYCLE 0x0010 #define MUL_PCI_RW_ENABLE 0x0008 /* * Receive descriptor start address */ #define RX_RING_ADDR_LO_REG 0x00e4 #define RX_RING_ADDR_HI_REG 0x00e8 /* * Max transmit packet size register */ #define TX_MAX_PKTSIZE_REG 0x00ec #define TX_MAX_PKTSIZE_REG_RESV 0xc0 #define TX_PKTSIZE_JUMBO 0x3b /* Realtek suggested value */ #define TX_PKTSIZE_STD 0x32 /* document suggested value */ #define RESV_82_REG 0x0082 #define RESV_E2_REG 0x00e2 /* * PHY registers */ /* * Basic mode control register */ #define PHY_BMCR_REG 0x00 #define PHY_RESET 0x8000 #define PHY_LOOPBACK 0x4000 #define PHY_SPEED_0 0x2000 #define PHY_SPEED_1 0x0040 #define PHY_SPEED_BITS (PHY_SPEED_0 | PHY_SPEED_1) #define PHY_SPEED_1000M PHY_SPEED_1 #define PHY_SPEED_100M PHY_SPEED_0 #define PHY_SPEED_10M 0x0000 #define PHY_SPEED_RES (PHY_SPEED_0 | PHY_SPEED_1) #define PHY_AUTO_NEGO 0x1000 #define PHY_RESTART_ANTO_NEGO 0x0200 #define PHY_DUPLEX_FULL 0x0100 #define PHY_BMCR_CLEAR 0xff40 /* * Basic mode status register */ #define PHY_BMSR_REG 0x01 #define PHY_100BASE_T4 0x8000 #define PHY_100BASE_TX_FULL 0x4000 #define PHY_100BASE_TX_HALF 0x2000 #define PHY_10BASE_T_FULL 0x1000 #define PHY_10BASE_T_HALF 0x0800 #define PHY_100BASE_T2_FULL 0x0400 #define PHY_100BASE_T2_HALF 0x0200 #define PHY_1000BASE_T_EXT 0x0100 #define PHY_AUTO_NEGO_END 0x0020 #define PHY_REMOTE_FAULT 0x0010 #define PHY_AUTO_NEGO_ABLE 0x0008 #define PHY_LINK_UP 0x0004 #define PHY_JABBER_DETECT 0x0002 #define PHY_EXT_ABLE 0x0001 /* * PHY identifier register */ #define PHY_ID_REG_1 0x02 #define PHY_ID_REG_2 0x03 #define PHY_VER_MASK 0x000f #define PHY_VER_S 0x0000 #define PHY_VER_SB 0x0010 /* * Auto-negotiation advertising register */ #define PHY_ANAR_REG 0x04 #define ANAR_NEXT_PAGE 0x8000 #define ANAR_REMOTE_FAULT 0x2000 #define ANAR_ASY_PAUSE 0x0800 #define ANAR_PAUSE 0x0400 #define ANAR_100BASE_T4 0x0200 #define ANAR_100BASE_TX_FULL 0x0100 #define ANAR_100BASE_TX_HALF 0x0080 #define ANAR_10BASE_T_FULL 0x0040 #define ANAR_10BASE_T_HALF 0x0020 #define ANAR_RESV_BITS 0x501f /* * Auto-negotiation link partner ability register */ #define PHY_ANLPAR_REG 0x05 /* * Auto-negotiation expansion register */ #define PHY_ANER_REG 0x06 /* * Auto-negotiation next page transmit register */ #define PHY_ANNPTR_REG 0x07 /* * Auto-negotiation next page receive register */ #define PHY_ANNPRR_REG 0x08 /* * 1000Base-T control register */ #define PHY_GBCR_REG 0x09 #define GBCR_MODE_JITTER 0x2000 #define GBCR_MODE_MASTER 0x4000 #define GBCR_MODE_SLAVE 0x6000 #define GBCR_1000BASE_T_FULL 0x0200 #define GBCR_1000BASE_T_HALF 0x0100 #define GBCR_DEFAULT 0x273a /* * 1000Base-T status register */ #define PHY_GBSR_REG 0x0a #define LP_1000BASE_T_FULL 0x0800 #define LP_1000BASE_T_HALF 0x0400 /* * 1000Base-T extended status register */ #define PHY_GBESR_REG 0x0f #define PHY_1F_REG 0x1f #define PHY_1C_REG 0x1c #define PHY_1B_REG 0x1b #define PHY_18_REG 0x18 #define PHY_15_REG 0x15 #define PHY_12_REG 0x12 #define PHY_0E_REG 0x0e #define PHY_0B_REG 0x0b /* * MII (PHY) registers, beyond those already defined in */ #define MII_AN_LPNXTPG 8 #define MII_1000BASE_T_CONTROL 9 #define MII_1000BASE_T_STATUS 10 #define MII_IEEE_EXT_STATUS 15 /* * New bits in the MII_CONTROL register */ #define MII_CONTROL_1000MB 0x0040 /* * New bits in the MII_AN_ADVERT register */ #define MII_ABILITY_ASYM_PAUSE 0x0800 #define MII_ABILITY_PAUSE 0x0400 /* * Values for the field of the MII_AN_ADVERT register */ #define MII_AN_SELECTOR_8023 0x0001 /* * Bits in the MII_1000BASE_T_CONTROL register * * The MASTER_CFG bit enables manual configuration of Master/Slave mode * (otherwise, roles are automatically negotiated). When this bit is set, * the MASTER_SEL bit forces Master mode, otherwise Slave mode is forced. */ #define MII_1000BT_CTL_MASTER_CFG 0x1000 /* enable role select */ #define MII_1000BT_CTL_MASTER_SEL 0x0800 /* role select bit */ #define MII_1000BT_CTL_ADV_FDX 0x0200 #define MII_1000BT_CTL_ADV_HDX 0x0100 /* * Vendor-specific MII registers */ #define MII_EXT_CONTROL MII_VENDOR(0) #define MII_EXT_STATUS MII_VENDOR(1) #define MII_RCV_ERR_COUNT MII_VENDOR(2) #define MII_FALSE_CARR_COUNT MII_VENDOR(3) #define MII_RCV_NOT_OK_COUNT MII_VENDOR(4) #define MII_AUX_CONTROL MII_VENDOR(8) #define MII_AUX_STATUS MII_VENDOR(9) #define MII_INTR_STATUS MII_VENDOR(10) #define MII_INTR_MASK MII_VENDOR(11) #define MII_HCD_STATUS MII_VENDOR(13) #define MII_MAXREG MII_VENDOR(15) /* 31, 0x1f */ /* * Bits in the MII_AUX_STATUS register */ #define MII_AUX_STATUS_MODE_MASK 0x0700 #define MII_AUX_STATUS_MODE_1000_F 0x0700 #define MII_AUX_STATUS_MODE_1000_H 0x0600 #define MII_AUX_STATUS_MODE_100_F 0x0500 #define MII_AUX_STATUS_MODE_100_4 0x0400 #define MII_AUX_STATUS_MODE_100_H 0x0300 #define MII_AUX_STATUS_MODE_10_F 0x0200 #define MII_AUX_STATUS_MODE_10_H 0x0100 #define MII_AUX_STATUS_MODE_NONE 0x0000 #define MII_AUX_STATUS_MODE_SHIFT 8 #define MII_AUX_STATUS_PAR_FAULT 0x0080 #define MII_AUX_STATUS_REM_FAULT 0x0040 #define MII_AUX_STATUS_LP_ANEG_ABLE 0x0010 #define MII_AUX_STATUS_LP_NP_ABLE 0x0008 #define MII_AUX_STATUS_LINKUP 0x0004 #define MII_AUX_STATUS_RX_PAUSE 0x0002 #define MII_AUX_STATUS_TX_PAUSE 0x0001 /* * Third section: * Hardware-defined data structures * * Note that the chip is naturally little-endian, so, for a little-endian * host, the structures defined below match those descibed in the PRM. * For big-endian hosts, some structures have to be swapped around. */ #if !defined(_BIG_ENDIAN) && !defined(_LITTLE_ENDIAN) #error Host endianness not defined #endif /* * Architectural constants: absolute maximum numbers of each type of ring */ #define RGE_SEND_SLOTS 1024 #define RGE_RECV_SLOTS 1024 #define RGE_BUFF_SIZE_STD 1536 /* 1536 bytes */ #define RGE_BUFF_SIZE_JUMBO 7168 /* maximum 7K */ #define RGE_JUMBO_SIZE 7014 #define RGE_JUMBO_MTU 7000 #define RGE_STATS_DUMP_SIZE 64 typedef struct rge_bd { volatile uint32_t flags_len; volatile uint32_t vlan_tag; volatile uint32_t host_buf_addr; volatile uint32_t host_buf_addr_hi; } rge_bd_t; #define BD_FLAG_HW_OWN 0x80000000 #define BD_FLAG_EOR 0x40000000 #define BD_FLAG_PKT_START 0x20000000 #define BD_FLAG_PKT_END 0x10000000 #define RBD_FLAG_MULTICAST 0x08000000 #define RBD_FLAG_UNICAST 0x04000000 #define RBD_FLAG_BROADCAST 0x02000000 #define RBD_FLAG_PKT_4096 0x00400000 #define RBD_FLAG_ERROR 0x00200000 #define RBD_FLAG_RUNT 0x00100000 #define RBD_FLAG_CRC_ERR 0x00080000 #define RBD_FLAG_PROTOCOL 0x00060000 #define RBD_FLAG_IP 0x00060000 #define RBD_FLAG_UDP 0x00040000 #define RBD_FLAG_TCP 0x00020000 #define RBD_FLAG_NONE_IP 0x00000000 #define RBD_IP_CKSUM_ERR 0x00010000 #define RBD_UDP_CKSUM_ERR 0x00008000 #define RBD_TCP_CKSUM_ERR 0x00004000 #define RBD_CKSUM_ERR 0x0001c000 #define RBD_FLAGS_MASK 0xffffc000 #define RBD_LEN_MASK 0x00003fff #define RBD_VLAN_PKT 0x00010000 #define RBD_VLAN_TAG 0x0000ffff #define SBD_FLAG_LARGE_SEND 0x08000000 #define SBD_FLAG_SEG_MAX 0x07ff0000 #define SBD_FLAG_IP_CKSUM 0x00040000 #define SBD_FLAG_UDP_CKSUM 0x00020000 #define SBD_FLAG_TCP_CKSUM 0x00010000 #define SBD_FLAG_TCP_UDP_CKSUM 0x00030000 #define SBD_LEN_MASK 0x0000ffff #define SBD_VLAN_PKT 0x00020000 #define SBD_VLAN_TAG 0x0000ffff #define SBD_FLAG_TX_PKT (BD_FLAG_HW_OWN | BD_FLAG_PKT_START | \ BD_FLAG_PKT_END) /* * Chip VLAN TCI format * bit0-3: VIDH The high 4 bits of a 12-bit VLAN ID * bit4: CFI Canonical format indicator * bit5-7: 3-bit 8-level priority * bit8-15: The low 8 bits of a 12-bit VLAN ID */ #define TCI_OS2CHIP(tci) (((tci & 0xff) << 8) | (tci >> 8)) #define TCI_CHIP2OS(tci) (((tci & 0xff00) >> 8) | (tci << 8)) /* * Hardware-defined Status Block */ typedef struct rge_hw_stats { uint64_t xmt_ok; uint64_t rcv_ok; uint64_t xmt_err; uint32_t rcv_err; uint16_t in_discards; uint16_t frame_err; uint32_t xmt_1col; uint32_t xmt_mcol; uint64_t unicast_rcv; uint64_t brdcst_rcv; uint32_t multi_rcv; uint16_t xmt_abt; uint16_t xmt_undrn; } rge_hw_stats_t; /* total 64 bytes */ #ifdef __cplusplus } #endif #endif /* _RGE_HW_H */