/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2009 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "bfe.h" #include "bfe_hw.h" /* * Broadcom BCM4401 chipsets use two rings : * * - One TX : For sending packets down the wire. * - One RX : For receving packets. * * Each ring can have any number of descriptors (configured during attach). * As of now we configure only 128 descriptor per ring (TX/RX). Each descriptor * has address (desc_addr) and control (desc_ctl) which holds a DMA buffer for * the packet and control information (like start/end of frame or end of table). * The descriptor table is allocated first and then a DMA buffer (for a packet) * is allocated and linked to each descriptor. * * Each descriptor entry is bfe_desc_t structure in bfe. During TX/RX * interrupt, the stat register will point to current descriptor being * processed. * * Here's an example of TX and RX ring : * * TX: * * Base of the descriptor table is programmed using BFE_DMATX_CTRL control * register. Each 'addr' points to DMA buffer (or packet data buffer) to * be transmitted and 'ctl' has the length of the packet (usually MTU). * * ----------------------| * | addr |Descriptor 0 | * | ctl | | * ----------------------| * | addr |Descriptor 1 | SOF (start of the frame) * | ctl | | * ----------------------| * | ... |Descriptor... | EOF (end of the frame) * | ... | | * ----------------------| * | addr |Descritor 127 | * | ctl | EOT | EOT (End of Table) * ----------------------| * * 'r_curr_desc' : pointer to current descriptor which can be used to transmit * a packet. * 'r_avail_desc' : decremented whenever a packet is being sent. * 'r_cons_desc' : incremented whenever a packet is sent down the wire and * notified by an interrupt to bfe driver. * * RX: * * Base of the descriptor table is programmed using BFE_DMARX_CTRL control * register. Each 'addr' points to DMA buffer (or packet data buffer). 'ctl' * contains the size of the DMA buffer and all the DMA buffers are * pre-allocated during attach and hence the maxmium size of the packet is * also known (r_buf_len from the bfe_rint_t structure). During RX interrupt * the packet length is embedded in bfe_header_t which is added by the * chip in the beginning of the packet. * * ----------------------| * | addr |Descriptor 0 | * | ctl | | * ----------------------| * | addr |Descriptor 1 | * | ctl | | * ----------------------| * | ... |Descriptor... | * | ... | | * ----------------------| * | addr |Descriptor 127| * | ctl | EOT | EOT (End of Table) * ----------------------| * * 'r_curr_desc' : pointer to current descriptor while receving a packet. * */ #define MODULE_NAME "bfe" /* * Used for checking PHY (link state, speed) */ #define BFE_TIMEOUT_INTERVAL (1000 * 1000 * 1000) /* * Chip restart action and reason for restart */ #define BFE_ACTION_RESTART 0x1 /* For restarting the chip */ #define BFE_ACTION_RESTART_SETPROP 0x2 /* restart due to setprop */ #define BFE_ACTION_RESTART_FAULT 0x4 /* restart due to fault */ #define BFE_ACTION_RESTART_PKT 0x8 /* restart due to pkt timeout */ static char bfe_ident[] = "bfe driver for Broadcom BCM4401 chipsets"; /* * Function Prototypes for bfe driver. */ static int bfe_check_link(bfe_t *); static void bfe_report_link(bfe_t *); static void bfe_chip_halt(bfe_t *); static void bfe_chip_reset(bfe_t *); static void bfe_tx_desc_init(bfe_ring_t *); static void bfe_rx_desc_init(bfe_ring_t *); static void bfe_set_rx_mode(bfe_t *); static void bfe_enable_chip_intrs(bfe_t *); static void bfe_chip_restart(bfe_t *); static void bfe_init_vars(bfe_t *); static void bfe_clear_stats(bfe_t *); static void bfe_gather_stats(bfe_t *); static void bfe_error(dev_info_t *, char *, ...); static int bfe_mac_getprop(void *, const char *, mac_prop_id_t, uint_t, uint_t, void *, uint_t *); static int bfe_mac_setprop(void *, const char *, mac_prop_id_t, uint_t, const void *); static int bfe_tx_reclaim(bfe_ring_t *); int bfe_mac_set_ether_addr(void *, const uint8_t *); /* * Macros for ddi_dma_sync(). */ #define SYNC_DESC(r, s, l, d) \ (void) ddi_dma_sync(r->r_desc_dma_handle, \ (off_t)(s * sizeof (bfe_desc_t)), \ (size_t)(l * sizeof (bfe_desc_t)), \ d) #define SYNC_BUF(r, s, b, l, d) \ (void) ddi_dma_sync(r->r_buf_dma[s].handle, \ (off_t)(b), (size_t)(l), d) /* * Supported Broadcom BCM4401 Cards. */ static bfe_cards_t bfe_cards[] = { { 0x14e4, 0x170c, "BCM4401 100Base-TX"}, }; /* * DMA attributes for device registers, packet data (buffer) and * descriptor table. */ static struct ddi_device_acc_attr bfe_dev_attr = { DDI_DEVICE_ATTR_V0, DDI_STRUCTURE_LE_ACC, DDI_STRICTORDER_ACC }; static struct ddi_device_acc_attr bfe_buf_attr = { DDI_DEVICE_ATTR_V0, DDI_NEVERSWAP_ACC, /* native endianness */ DDI_STRICTORDER_ACC }; static ddi_dma_attr_t bfe_dma_attr_buf = { DMA_ATTR_V0, /* dma_attr_version */ 0, /* dma_attr_addr_lo */ BFE_PCI_DMA - 1, /* dma_attr_addr_hi */ 0x1fff, /* dma_attr_count_max */ 8, /* dma_attr_align */ 0, /* dma_attr_burstsizes */ 1, /* dma_attr_minxfer */ 0x1fff, /* dma_attr_maxxfer */ BFE_PCI_DMA - 1, /* dma_attr_seg */ 1, /* dma_attr_sgllen */ 1, /* dma_attr_granular */ 0 /* dma_attr_flags */ }; static ddi_dma_attr_t bfe_dma_attr_desc = { DMA_ATTR_V0, /* dma_attr_version */ 0, /* dma_attr_addr_lo */ BFE_PCI_DMA - 1, /* dma_attr_addr_hi */ BFE_PCI_DMA - 1, /* dma_attr_count_max */ BFE_DESC_ALIGN, /* dma_attr_align */ 0, /* dma_attr_burstsizes */ 1, /* dma_attr_minxfer */ BFE_PCI_DMA - 1, /* dma_attr_maxxfer */ BFE_PCI_DMA - 1, /* dma_attr_seg */ 1, /* dma_attr_sgllen */ 1, /* dma_attr_granular */ 0 /* dma_attr_flags */ }; /* * Ethernet broadcast addresses. */ static uchar_t bfe_broadcast[ETHERADDRL] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; #define ASSERT_ALL_LOCKS(bfe) { \ ASSERT(mutex_owned(&bfe->bfe_tx_ring.r_lock)); \ ASSERT(rw_write_held(&bfe->bfe_rwlock)); \ } /* * Debugging and error reproting code. */ static void bfe_error(dev_info_t *dip, char *fmt, ...) { va_list ap; char buf[256]; va_start(ap, fmt); (void) vsnprintf(buf, sizeof (buf), fmt, ap); va_end(ap); if (dip) { cmn_err(CE_WARN, "%s%d: %s", ddi_driver_name(dip), ddi_get_instance(dip), buf); } else { cmn_err(CE_WARN, "bfe: %s", buf); } } /* * Grabs all necessary locks to block any other operation on the chip. */ static void bfe_grab_locks(bfe_t *bfe) { bfe_ring_t *tx = &bfe->bfe_tx_ring; /* * Grab all the locks. * - bfe_rwlock : locks down whole chip including RX. * - tx's r_lock : locks down only TX side. */ rw_enter(&bfe->bfe_rwlock, RW_WRITER); mutex_enter(&tx->r_lock); /* * Note that we don't use RX's r_lock. */ } /* * Release lock on chip/drver. */ static void bfe_release_locks(bfe_t *bfe) { bfe_ring_t *tx = &bfe->bfe_tx_ring; /* * Release all the locks in the order in which they were grabbed. */ mutex_exit(&tx->r_lock); rw_exit(&bfe->bfe_rwlock); } /* * It's used to make sure that the write to device register was successful. */ static int bfe_wait_bit(bfe_t *bfe, uint32_t reg, uint32_t bit, ulong_t t, const int clear) { ulong_t i; uint32_t v; for (i = 0; i < t; i++) { v = INL(bfe, reg); if (clear && !(v & bit)) break; if (!clear && (v & bit)) break; drv_usecwait(10); } /* if device still didn't see the value */ if (i == t) return (-1); return (0); } /* * PHY functions (read, write, stop, reset and startup) */ static int bfe_read_phy(bfe_t *bfe, uint32_t reg) { OUTL(bfe, BFE_EMAC_ISTAT, BFE_EMAC_INT_MII); OUTL(bfe, BFE_MDIO_DATA, (BFE_MDIO_SB_START | (BFE_MDIO_OP_READ << BFE_MDIO_OP_SHIFT) | (bfe->bfe_phy_addr << BFE_MDIO_PMD_SHIFT) | (reg << BFE_MDIO_RA_SHIFT) | (BFE_MDIO_TA_VALID << BFE_MDIO_TA_SHIFT))); (void) bfe_wait_bit(bfe, BFE_EMAC_ISTAT, BFE_EMAC_INT_MII, 10, 0); return ((INL(bfe, BFE_MDIO_DATA) & BFE_MDIO_DATA_DATA)); } static void bfe_write_phy(bfe_t *bfe, uint32_t reg, uint32_t val) { OUTL(bfe, BFE_EMAC_ISTAT, BFE_EMAC_INT_MII); OUTL(bfe, BFE_MDIO_DATA, (BFE_MDIO_SB_START | (BFE_MDIO_OP_WRITE << BFE_MDIO_OP_SHIFT) | (bfe->bfe_phy_addr << BFE_MDIO_PMD_SHIFT) | (reg << BFE_MDIO_RA_SHIFT) | (BFE_MDIO_TA_VALID << BFE_MDIO_TA_SHIFT) | (val & BFE_MDIO_DATA_DATA))); (void) bfe_wait_bit(bfe, BFE_EMAC_ISTAT, BFE_EMAC_INT_MII, 10, 0); } /* * It resets the PHY layer. */ static int bfe_reset_phy(bfe_t *bfe) { uint32_t i; bfe_write_phy(bfe, MII_CONTROL, MII_CONTROL_RESET); drv_usecwait(100); for (i = 0; i < 10; i++) { if (bfe_read_phy(bfe, MII_CONTROL) & MII_CONTROL_RESET) { drv_usecwait(500); continue; } break; } if (i == 10) { bfe_error(bfe->bfe_dip, "Timeout waiting for PHY to reset"); bfe->bfe_phy_state = BFE_PHY_RESET_TIMEOUT; return (BFE_FAILURE); } bfe->bfe_phy_state = BFE_PHY_RESET_DONE; return (BFE_SUCCESS); } /* * Make sure timer function is out of our way and especially during * detach. */ static void bfe_stop_timer(bfe_t *bfe) { if (bfe->bfe_periodic_id) { ddi_periodic_delete(bfe->bfe_periodic_id); bfe->bfe_periodic_id = NULL; } } /* * Stops the PHY */ static void bfe_stop_phy(bfe_t *bfe) { bfe_write_phy(bfe, MII_CONTROL, MII_CONTROL_PWRDN | MII_CONTROL_ISOLATE); bfe->bfe_chip.link = LINK_STATE_UNKNOWN; bfe->bfe_chip.speed = 0; bfe->bfe_chip.duplex = LINK_DUPLEX_UNKNOWN; bfe->bfe_phy_state = BFE_PHY_STOPPED; /* * Report the link status to MAC layer. */ if (bfe->bfe_machdl != NULL) (void) bfe_report_link(bfe); } static int bfe_probe_phy(bfe_t *bfe) { int phy; uint32_t status; if (bfe->bfe_phy_addr) { status = bfe_read_phy(bfe, MII_STATUS); if (status != 0xffff && status != 0) { bfe_write_phy(bfe, MII_CONTROL, 0); return (BFE_SUCCESS); } } for (phy = 0; phy < 32; phy++) { bfe->bfe_phy_addr = phy; status = bfe_read_phy(bfe, MII_STATUS); if (status != 0xffff && status != 0) { bfe_write_phy(bfe, MII_CONTROL, 0); return (BFE_SUCCESS); } } return (BFE_FAILURE); } /* * This timeout function fires at BFE_TIMEOUT_INTERVAL to check the link * status. */ static void bfe_timeout(void *arg) { bfe_t *bfe = (bfe_t *)arg; int resched = 0; /* * We don't grab any lock because bfe can't go away. * untimeout() will wait for this timeout instance to complete. */ if (bfe->bfe_chip_action & BFE_ACTION_RESTART) { /* * Restart the chip. */ bfe_grab_locks(bfe); bfe_chip_restart(bfe); bfe->bfe_chip_action &= ~BFE_ACTION_RESTART; bfe->bfe_chip_action &= ~BFE_ACTION_RESTART_FAULT; bfe->bfe_chip_action &= ~BFE_ACTION_RESTART_PKT; bfe_release_locks(bfe); mac_tx_update(bfe->bfe_machdl); /* Restart will register a new timeout */ return; } rw_enter(&bfe->bfe_rwlock, RW_READER); if (bfe->bfe_chip_state == BFE_CHIP_ACTIVE) { hrtime_t hr; hr = gethrtime(); if (bfe->bfe_tx_stall_time != 0 && hr > bfe->bfe_tx_stall_time) { DTRACE_PROBE2(chip__restart, int, bfe->bfe_unit, char *, "pkt timeout"); bfe->bfe_chip_action |= (BFE_ACTION_RESTART | BFE_ACTION_RESTART_PKT); bfe->bfe_tx_stall_time = 0; } } if (bfe->bfe_phy_state == BFE_PHY_STARTED) { /* * Report the link status to MAC layer if link status changed. */ if (bfe_check_link(bfe)) { bfe_report_link(bfe); if (bfe->bfe_chip.link == LINK_STATE_UP) { uint32_t val, flow; val = INL(bfe, BFE_TX_CTRL); val &= ~BFE_TX_DUPLEX; if (bfe->bfe_chip.duplex == LINK_DUPLEX_FULL) { val |= BFE_TX_DUPLEX; flow = INL(bfe, BFE_RXCONF); flow &= ~BFE_RXCONF_FLOW; OUTL(bfe, BFE_RXCONF, flow); flow = INL(bfe, BFE_MAC_FLOW); flow &= ~(BFE_FLOW_RX_HIWAT); OUTL(bfe, BFE_MAC_FLOW, flow); } resched = 1; OUTL(bfe, BFE_TX_CTRL, val); DTRACE_PROBE1(link__up, int, bfe->bfe_unit); } } } rw_exit(&bfe->bfe_rwlock); if (resched) mac_tx_update(bfe->bfe_machdl); } /* * Starts PHY layer. */ static int bfe_startup_phy(bfe_t *bfe) { uint16_t bmsr, bmcr, anar; int prog, s; int phyid1, phyid2; if (bfe_probe_phy(bfe) == BFE_FAILURE) { bfe->bfe_phy_state = BFE_PHY_NOTFOUND; return (BFE_FAILURE); } (void) bfe_reset_phy(bfe); phyid1 = bfe_read_phy(bfe, MII_PHYIDH); phyid2 = bfe_read_phy(bfe, MII_PHYIDL); bfe->bfe_phy_id = (phyid1 << 16) | phyid2; bmsr = bfe_read_phy(bfe, MII_STATUS); anar = bfe_read_phy(bfe, MII_AN_ADVERT); again: anar &= ~(MII_ABILITY_100BASE_T4 | MII_ABILITY_100BASE_TX_FD | MII_ABILITY_100BASE_TX | MII_ABILITY_10BASE_T_FD | MII_ABILITY_10BASE_T); /* * Supported hardware modes are in bmsr. */ bfe->bfe_chip.bmsr = bmsr; /* * Assume no capabilities are supported in the hardware. */ bfe->bfe_cap_aneg = bfe->bfe_cap_100T4 = bfe->bfe_cap_100fdx = bfe->bfe_cap_100hdx = bfe->bfe_cap_10fdx = bfe->bfe_cap_10hdx = 0; /* * Assume property is set. */ s = 1; if (!(bfe->bfe_chip_action & BFE_ACTION_RESTART_SETPROP)) { /* * Property is not set which means bfe_mac_setprop() * is not called on us. */ s = 0; } bmcr = prog = 0; if (bmsr & MII_STATUS_100_BASEX_FD) { bfe->bfe_cap_100fdx = 1; if (s == 0) { anar |= MII_ABILITY_100BASE_TX_FD; bfe->bfe_adv_100fdx = 1; prog++; } else if (bfe->bfe_adv_100fdx) { anar |= MII_ABILITY_100BASE_TX_FD; prog++; } } if (bmsr & MII_STATUS_100_BASE_T4) { bfe->bfe_cap_100T4 = 1; if (s == 0) { anar |= MII_ABILITY_100BASE_T4; bfe->bfe_adv_100T4 = 1; prog++; } else if (bfe->bfe_adv_100T4) { anar |= MII_ABILITY_100BASE_T4; prog++; } } if (bmsr & MII_STATUS_100_BASEX) { bfe->bfe_cap_100hdx = 1; if (s == 0) { anar |= MII_ABILITY_100BASE_TX; bfe->bfe_adv_100hdx = 1; prog++; } else if (bfe->bfe_adv_100hdx) { anar |= MII_ABILITY_100BASE_TX; prog++; } } if (bmsr & MII_STATUS_10_FD) { bfe->bfe_cap_10fdx = 1; if (s == 0) { anar |= MII_ABILITY_10BASE_T_FD; bfe->bfe_adv_10fdx = 1; prog++; } else if (bfe->bfe_adv_10fdx) { anar |= MII_ABILITY_10BASE_T_FD; prog++; } } if (bmsr & MII_STATUS_10) { bfe->bfe_cap_10hdx = 1; if (s == 0) { anar |= MII_ABILITY_10BASE_T; bfe->bfe_adv_10hdx = 1; prog++; } else if (bfe->bfe_adv_10hdx) { anar |= MII_ABILITY_10BASE_T; prog++; } } if (bmsr & MII_STATUS_CANAUTONEG) { bfe->bfe_cap_aneg = 1; if (s == 0) { bfe->bfe_adv_aneg = 1; } } if (prog == 0) { if (s == 0) { bfe_error(bfe->bfe_dip, "No valid link mode selected. Powering down PHY"); bfe_stop_phy(bfe); bfe_report_link(bfe); return (BFE_FAILURE); } /* * If property is set then user would have goofed up. So we * go back to default properties. */ bfe->bfe_chip_action &= ~BFE_ACTION_RESTART_SETPROP; goto again; } if (bfe->bfe_adv_aneg && (bmsr & MII_STATUS_CANAUTONEG)) { bmcr = (MII_CONTROL_ANE | MII_CONTROL_RSAN); } else { if (bfe->bfe_adv_100fdx) bmcr = (MII_CONTROL_100MB | MII_CONTROL_FDUPLEX); else if (bfe->bfe_adv_100hdx) bmcr = MII_CONTROL_100MB; else if (bfe->bfe_adv_10fdx) bmcr = MII_CONTROL_FDUPLEX; else bmcr = 0; /* 10HDX */ } if (prog) bfe_write_phy(bfe, MII_AN_ADVERT, anar); if (bmcr) bfe_write_phy(bfe, MII_CONTROL, bmcr); bfe->bfe_mii_anar = anar; bfe->bfe_mii_bmcr = bmcr; bfe->bfe_phy_state = BFE_PHY_STARTED; if (bfe->bfe_periodic_id == NULL) { bfe->bfe_periodic_id = ddi_periodic_add(bfe_timeout, (void *)bfe, BFE_TIMEOUT_INTERVAL, DDI_IPL_0); DTRACE_PROBE1(first__timeout, int, bfe->bfe_unit); } DTRACE_PROBE4(phy_started, int, bfe->bfe_unit, int, bmsr, int, bmcr, int, anar); return (BFE_SUCCESS); } /* * Reports link status back to MAC Layer. */ static void bfe_report_link(bfe_t *bfe) { mac_link_update(bfe->bfe_machdl, bfe->bfe_chip.link); } /* * Reads PHY/MII registers and get the link status for us. */ static int bfe_check_link(bfe_t *bfe) { uint16_t bmsr, bmcr, anar, anlpar; int speed, duplex, link; speed = bfe->bfe_chip.speed; duplex = bfe->bfe_chip.duplex; link = bfe->bfe_chip.link; bmsr = bfe_read_phy(bfe, MII_STATUS); bfe->bfe_mii_bmsr = bmsr; bmcr = bfe_read_phy(bfe, MII_CONTROL); anar = bfe_read_phy(bfe, MII_AN_ADVERT); bfe->bfe_mii_anar = anar; anlpar = bfe_read_phy(bfe, MII_AN_LPABLE); bfe->bfe_mii_anlpar = anlpar; bfe->bfe_mii_exp = bfe_read_phy(bfe, MII_AN_EXPANSION); /* * If exp register is not present in PHY. */ if (bfe->bfe_mii_exp == 0xffff) { bfe->bfe_mii_exp = 0; } if ((bmsr & MII_STATUS_LINKUP) == 0) { bfe->bfe_chip.link = LINK_STATE_DOWN; bfe->bfe_chip.speed = 0; bfe->bfe_chip.duplex = LINK_DUPLEX_UNKNOWN; goto done; } bfe->bfe_chip.link = LINK_STATE_UP; if (!(bmcr & MII_CONTROL_ANE)) { /* Forced mode */ if (bmcr & MII_CONTROL_100MB) bfe->bfe_chip.speed = 100000000; else bfe->bfe_chip.speed = 10000000; if (bmcr & MII_CONTROL_FDUPLEX) bfe->bfe_chip.duplex = LINK_DUPLEX_FULL; else bfe->bfe_chip.duplex = LINK_DUPLEX_HALF; } else if ((!(bmsr & MII_STATUS_CANAUTONEG)) || (!(bmsr & MII_STATUS_ANDONE))) { bfe->bfe_chip.speed = 0; bfe->bfe_chip.duplex = LINK_DUPLEX_UNKNOWN; } else if (anar & anlpar & MII_ABILITY_100BASE_TX_FD) { bfe->bfe_chip.speed = 100000000; bfe->bfe_chip.duplex = LINK_DUPLEX_FULL; } else if (anar & anlpar & MII_ABILITY_100BASE_T4) { bfe->bfe_chip.speed = 100000000; bfe->bfe_chip.duplex = LINK_DUPLEX_HALF; } else if (anar & anlpar & MII_ABILITY_100BASE_TX) { bfe->bfe_chip.speed = 100000000; bfe->bfe_chip.duplex = LINK_DUPLEX_HALF; } else if (anar & anlpar & MII_ABILITY_10BASE_T_FD) { bfe->bfe_chip.speed = 10000000; bfe->bfe_chip.duplex = LINK_DUPLEX_FULL; } else if (anar & anlpar & MII_ABILITY_10BASE_T) { bfe->bfe_chip.speed = 10000000; bfe->bfe_chip.duplex = LINK_DUPLEX_HALF; } else { bfe->bfe_chip.speed = 0; bfe->bfe_chip.duplex = LINK_DUPLEX_UNKNOWN; } done: /* * If speed or link status or duplex mode changed then report to * MAC layer which is done by the caller. */ if (speed != bfe->bfe_chip.speed || duplex != bfe->bfe_chip.duplex || link != bfe->bfe_chip.link) { return (1); } return (0); } static void bfe_cam_write(bfe_t *bfe, uchar_t *d, int index) { uint32_t v; v = ((uint32_t)d[2] << 24); v |= ((uint32_t)d[3] << 16); v |= ((uint32_t)d[4] << 8); v |= (uint32_t)d[5]; OUTL(bfe, BFE_CAM_DATA_LO, v); v = (BFE_CAM_HI_VALID | (((uint32_t)d[0]) << 8) | (((uint32_t)d[1]))); OUTL(bfe, BFE_CAM_DATA_HI, v); OUTL(bfe, BFE_CAM_CTRL, (BFE_CAM_WRITE | ((uint32_t)index << BFE_CAM_INDEX_SHIFT))); (void) bfe_wait_bit(bfe, BFE_CAM_CTRL, BFE_CAM_BUSY, 10, 1); } /* * Chip related functions (halt, reset, start). */ static void bfe_chip_halt(bfe_t *bfe) { /* * Disables interrupts. */ OUTL(bfe, BFE_INTR_MASK, 0); FLUSH(bfe, BFE_INTR_MASK); OUTL(bfe, BFE_ENET_CTRL, BFE_ENET_DISABLE); /* * Wait until TX and RX finish their job. */ (void) bfe_wait_bit(bfe, BFE_ENET_CTRL, BFE_ENET_DISABLE, 20, 1); /* * Disables DMA engine. */ OUTL(bfe, BFE_DMARX_CTRL, 0); OUTL(bfe, BFE_DMATX_CTRL, 0); drv_usecwait(10); bfe->bfe_chip_state = BFE_CHIP_HALT; } static void bfe_chip_restart(bfe_t *bfe) { DTRACE_PROBE2(chip__restart, int, bfe->bfe_unit, int, bfe->bfe_chip_action); /* * Halt chip and PHY. */ bfe_chip_halt(bfe); bfe_stop_phy(bfe); bfe->bfe_chip_state = BFE_CHIP_STOPPED; /* * Init variables. */ bfe_init_vars(bfe); /* * Reset chip and start PHY. */ bfe_chip_reset(bfe); /* * DMA descriptor rings. */ bfe_tx_desc_init(&bfe->bfe_tx_ring); bfe_rx_desc_init(&bfe->bfe_rx_ring); bfe->bfe_chip_state = BFE_CHIP_ACTIVE; bfe_set_rx_mode(bfe); bfe_enable_chip_intrs(bfe); } /* * Disables core by stopping the clock. */ static void bfe_core_disable(bfe_t *bfe) { if ((INL(bfe, BFE_SBTMSLOW) & BFE_RESET)) return; OUTL(bfe, BFE_SBTMSLOW, (BFE_REJECT | BFE_CLOCK)); (void) bfe_wait_bit(bfe, BFE_SBTMSLOW, BFE_REJECT, 100, 0); (void) bfe_wait_bit(bfe, BFE_SBTMSHIGH, BFE_BUSY, 100, 1); OUTL(bfe, BFE_SBTMSLOW, (BFE_FGC | BFE_CLOCK | BFE_REJECT | BFE_RESET)); FLUSH(bfe, BFE_SBTMSLOW); drv_usecwait(10); OUTL(bfe, BFE_SBTMSLOW, (BFE_REJECT | BFE_RESET)); drv_usecwait(10); } /* * Resets core. */ static void bfe_core_reset(bfe_t *bfe) { uint32_t val; /* * First disable the core. */ bfe_core_disable(bfe); OUTL(bfe, BFE_SBTMSLOW, (BFE_RESET | BFE_CLOCK | BFE_FGC)); FLUSH(bfe, BFE_SBTMSLOW); drv_usecwait(1); if (INL(bfe, BFE_SBTMSHIGH) & BFE_SERR) OUTL(bfe, BFE_SBTMSHIGH, 0); val = INL(bfe, BFE_SBIMSTATE); if (val & (BFE_IBE | BFE_TO)) OUTL(bfe, BFE_SBIMSTATE, val & ~(BFE_IBE | BFE_TO)); OUTL(bfe, BFE_SBTMSLOW, (BFE_CLOCK | BFE_FGC)); FLUSH(bfe, BFE_SBTMSLOW); drv_usecwait(1); OUTL(bfe, BFE_SBTMSLOW, BFE_CLOCK); FLUSH(bfe, BFE_SBTMSLOW); drv_usecwait(1); } static void bfe_setup_config(bfe_t *bfe, uint32_t cores) { uint32_t bar_orig, val; /* * Change bar0 window to map sbtopci registers. */ bar_orig = pci_config_get32(bfe->bfe_conf_handle, BFE_BAR0_WIN); pci_config_put32(bfe->bfe_conf_handle, BFE_BAR0_WIN, BFE_REG_PCI); /* Just read it and don't do anything */ val = INL(bfe, BFE_SBIDHIGH) & BFE_IDH_CORE; val = INL(bfe, BFE_SBINTVEC); val |= cores; OUTL(bfe, BFE_SBINTVEC, val); val = INL(bfe, BFE_SSB_PCI_TRANS_2); val |= BFE_SSB_PCI_PREF | BFE_SSB_PCI_BURST; OUTL(bfe, BFE_SSB_PCI_TRANS_2, val); /* * Restore bar0 window mapping. */ pci_config_put32(bfe->bfe_conf_handle, BFE_BAR0_WIN, bar_orig); } /* * Resets chip and starts PHY. */ static void bfe_chip_reset(bfe_t *bfe) { uint32_t val; /* Set the interrupt vector for the enet core */ bfe_setup_config(bfe, BFE_INTVEC_ENET0); /* check if core is up */ val = INL(bfe, BFE_SBTMSLOW) & (BFE_RESET | BFE_REJECT | BFE_CLOCK); if (val == BFE_CLOCK) { OUTL(bfe, BFE_RCV_LAZY, 0); OUTL(bfe, BFE_ENET_CTRL, BFE_ENET_DISABLE); (void) bfe_wait_bit(bfe, BFE_ENET_CTRL, BFE_ENET_DISABLE, 10, 1); OUTL(bfe, BFE_DMATX_CTRL, 0); FLUSH(bfe, BFE_DMARX_STAT); drv_usecwait(20000); /* 20 milli seconds */ if (INL(bfe, BFE_DMARX_STAT) & BFE_STAT_EMASK) { (void) bfe_wait_bit(bfe, BFE_DMARX_STAT, BFE_STAT_SIDLE, 10, 0); } OUTL(bfe, BFE_DMARX_CTRL, 0); } bfe_core_reset(bfe); bfe_clear_stats(bfe); OUTL(bfe, BFE_MDIO_CTRL, 0x8d); val = INL(bfe, BFE_DEVCTRL); if (!(val & BFE_IPP)) OUTL(bfe, BFE_ENET_CTRL, BFE_ENET_EPSEL); else if (INL(bfe, BFE_DEVCTRL & BFE_EPR)) { OUTL_AND(bfe, BFE_DEVCTRL, ~BFE_EPR); drv_usecwait(20000); /* 20 milli seconds */ } OUTL_OR(bfe, BFE_MAC_CTRL, BFE_CTRL_CRC32_ENAB | BFE_CTRL_LED); OUTL_AND(bfe, BFE_MAC_CTRL, ~BFE_CTRL_PDOWN); OUTL(bfe, BFE_RCV_LAZY, ((1 << BFE_LAZY_FC_SHIFT) & BFE_LAZY_FC_MASK)); OUTL_OR(bfe, BFE_RCV_LAZY, 0); OUTL(bfe, BFE_RXMAXLEN, bfe->bfe_rx_ring.r_buf_len); OUTL(bfe, BFE_TXMAXLEN, bfe->bfe_tx_ring.r_buf_len); OUTL(bfe, BFE_TX_WMARK, 56); /* Program DMA channels */ OUTL(bfe, BFE_DMATX_CTRL, BFE_TX_CTRL_ENABLE); /* * DMA addresses need to be added to BFE_PCI_DMA */ OUTL(bfe, BFE_DMATX_ADDR, bfe->bfe_tx_ring.r_desc_cookie.dmac_laddress + BFE_PCI_DMA); OUTL(bfe, BFE_DMARX_CTRL, (BFE_RX_OFFSET << BFE_RX_CTRL_ROSHIFT) | BFE_RX_CTRL_ENABLE); OUTL(bfe, BFE_DMARX_ADDR, bfe->bfe_rx_ring.r_desc_cookie.dmac_laddress + BFE_PCI_DMA); (void) bfe_startup_phy(bfe); bfe->bfe_chip_state = BFE_CHIP_INITIALIZED; } /* * It enables interrupts. Should be the last step while starting chip. */ static void bfe_enable_chip_intrs(bfe_t *bfe) { /* Enable the chip and core */ OUTL(bfe, BFE_ENET_CTRL, BFE_ENET_ENABLE); /* Enable interrupts */ OUTL(bfe, BFE_INTR_MASK, BFE_IMASK_DEF); } /* * Common code to take care of setting RX side mode (filter). */ static void bfe_set_rx_mode(bfe_t *bfe) { uint32_t val; int i; ether_addr_t mac[ETHERADDRL] = {0, 0, 0, 0, 0, 0}; /* * We don't touch RX filter if we were asked to suspend. It's fine * if chip is not active (no interface is plumbed on us). */ if (bfe->bfe_chip_state == BFE_CHIP_SUSPENDED) return; val = INL(bfe, BFE_RXCONF); val &= ~BFE_RXCONF_PROMISC; val &= ~BFE_RXCONF_DBCAST; if ((bfe->bfe_chip_mode & BFE_RX_MODE_ENABLE) == 0) { OUTL(bfe, BFE_CAM_CTRL, 0); FLUSH(bfe, BFE_CAM_CTRL); } else if (bfe->bfe_chip_mode & BFE_RX_MODE_PROMISC) { val |= BFE_RXCONF_PROMISC; val &= ~BFE_RXCONF_DBCAST; } else { if (bfe->bfe_chip_state == BFE_CHIP_ACTIVE) { /* Flush everything */ OUTL(bfe, BFE_RXCONF, val | BFE_RXCONF_PROMISC | BFE_RXCONF_ALLMULTI); FLUSH(bfe, BFE_RXCONF); } /* Disable CAM */ OUTL(bfe, BFE_CAM_CTRL, 0); FLUSH(bfe, BFE_CAM_CTRL); /* * We receive all multicast packets. */ val |= BFE_RXCONF_ALLMULTI; for (i = 0; i < BFE_MAX_MULTICAST_TABLE - 1; i++) { bfe_cam_write(bfe, (uchar_t *)mac, i); } bfe_cam_write(bfe, bfe->bfe_ether_addr, i); /* Enable CAM */ OUTL_OR(bfe, BFE_CAM_CTRL, BFE_CAM_ENABLE); FLUSH(bfe, BFE_CAM_CTRL); } DTRACE_PROBE2(rx__mode__filter, int, bfe->bfe_unit, int, val); OUTL(bfe, BFE_RXCONF, val); FLUSH(bfe, BFE_RXCONF); } /* * Reset various variable values to initial state. */ static void bfe_init_vars(bfe_t *bfe) { bfe->bfe_chip_mode = BFE_RX_MODE_ENABLE; /* Initial assumption */ bfe->bfe_chip.link = LINK_STATE_UNKNOWN; bfe->bfe_chip.speed = 0; bfe->bfe_chip.duplex = LINK_DUPLEX_UNKNOWN; bfe->bfe_periodic_id = NULL; bfe->bfe_chip_state = BFE_CHIP_UNINITIALIZED; bfe->bfe_tx_stall_time = 0; } /* * Initializes TX side descriptor entries (bfe_desc_t). Each descriptor entry * has control (desc_ctl) and address (desc_addr) member. */ static void bfe_tx_desc_init(bfe_ring_t *r) { int i; uint32_t v; for (i = 0; i < r->r_ndesc; i++) { PUT_DESC(r, (uint32_t *)&(r->r_desc[i].desc_ctl), (r->r_buf_dma[i].len & BFE_DESC_LEN)); /* * DMA addresses need to be added to BFE_PCI_DMA */ PUT_DESC(r, (uint32_t *)&(r->r_desc[i].desc_addr), (r->r_buf_dma[i].cookie.dmac_laddress + BFE_PCI_DMA)); } v = GET_DESC(r, (uint32_t *)&(r->r_desc[i - 1].desc_ctl)); PUT_DESC(r, (uint32_t *)&(r->r_desc[i - 1].desc_ctl), v | BFE_DESC_EOT); (void) SYNC_DESC(r, 0, r->r_ndesc, DDI_DMA_SYNC_FORDEV); r->r_curr_desc = 0; r->r_avail_desc = TX_NUM_DESC; r->r_cons_desc = 0; } /* * Initializes RX side descriptor entries (bfe_desc_t). Each descriptor entry * has control (desc_ctl) and address (desc_addr) member. */ static void bfe_rx_desc_init(bfe_ring_t *r) { int i; uint32_t v; for (i = 0; i < r->r_ndesc; i++) { PUT_DESC(r, (uint32_t *)&(r->r_desc[i].desc_ctl), (r->r_buf_dma[i].len& BFE_DESC_LEN)); PUT_DESC(r, (uint32_t *)&(r->r_desc[i].desc_addr), (r->r_buf_dma[i].cookie.dmac_laddress + BFE_PCI_DMA)); /* Initialize rx header (len, flags) */ bzero(r->r_buf_dma[i].addr, sizeof (bfe_rx_header_t)); (void) SYNC_BUF(r, i, 0, sizeof (bfe_rx_header_t), DDI_DMA_SYNC_FORDEV); } v = GET_DESC(r, (uint32_t *)&(r->r_desc[i - 1].desc_ctl)); PUT_DESC(r, (uint32_t *)&(r->r_desc[i - 1].desc_ctl), v | BFE_DESC_EOT); (void) SYNC_DESC(r, 0, r->r_ndesc, DDI_DMA_SYNC_FORDEV); /* TAIL of RX Descriptor */ OUTL(r->r_bfe, BFE_DMARX_PTR, ((i) * sizeof (bfe_desc_t))); r->r_curr_desc = 0; r->r_avail_desc = RX_NUM_DESC; } static int bfe_chip_start(bfe_t *bfe) { ASSERT_ALL_LOCKS(bfe); /* * Stop the chip first & then Reset the chip. At last enable interrupts. */ bfe_chip_halt(bfe); bfe_stop_phy(bfe); /* * Reset chip and start PHY. */ bfe_chip_reset(bfe); /* * Initailize Descriptor Rings. */ bfe_tx_desc_init(&bfe->bfe_tx_ring); bfe_rx_desc_init(&bfe->bfe_rx_ring); bfe->bfe_chip_state = BFE_CHIP_ACTIVE; bfe->bfe_chip_mode |= BFE_RX_MODE_ENABLE; bfe_set_rx_mode(bfe); bfe_enable_chip_intrs(bfe); /* Check link, speed and duplex mode */ (void) bfe_check_link(bfe); return (DDI_SUCCESS); } /* * Clear chip statistics. */ static void bfe_clear_stats(bfe_t *bfe) { ulong_t r; OUTL(bfe, BFE_MIB_CTRL, BFE_MIB_CLR_ON_READ); /* * Stat registers are cleared by reading. */ for (r = BFE_TX_GOOD_O; r <= BFE_TX_PAUSE; r += 4) (void) INL(bfe, r); for (r = BFE_RX_GOOD_O; r <= BFE_RX_NPAUSE; r += 4) (void) INL(bfe, r); } /* * Collect chip statistics. */ static void bfe_gather_stats(bfe_t *bfe) { ulong_t r; uint32_t *v; uint32_t txerr = 0, rxerr = 0, coll = 0; v = &bfe->bfe_hw_stats.tx_good_octets; for (r = BFE_TX_GOOD_O; r <= BFE_TX_PAUSE; r += 4) { *v += INL(bfe, r); v++; } v = &bfe->bfe_hw_stats.rx_good_octets; for (r = BFE_RX_GOOD_O; r <= BFE_RX_NPAUSE; r += 4) { *v += INL(bfe, r); v++; } /* * TX : * ------- * tx_good_octets, tx_good_pkts, tx_octets * tx_pkts, tx_broadcast_pkts, tx_multicast_pkts * tx_len_64, tx_len_65_to_127, tx_len_128_to_255 * tx_len_256_to_511, tx_len_512_to_1023, tx_len_1024_to_max * tx_jabber_pkts, tx_oversize_pkts, tx_fragment_pkts * tx_underruns, tx_total_cols, tx_single_cols * tx_multiple_cols, tx_excessive_cols, tx_late_cols * tx_defered, tx_carrier_lost, tx_pause_pkts * * RX : * ------- * rx_good_octets, rx_good_pkts, rx_octets * rx_pkts, rx_broadcast_pkts, rx_multicast_pkts * rx_len_64, rx_len_65_to_127, rx_len_128_to_255 * rx_len_256_to_511, rx_len_512_to_1023, rx_len_1024_to_max * rx_jabber_pkts, rx_oversize_pkts, rx_fragment_pkts * rx_missed_pkts, rx_crc_align_errs, rx_undersize * rx_crc_errs, rx_align_errs, rx_symbol_errs * rx_pause_pkts, rx_nonpause_pkts */ bfe->bfe_stats.ether_stat_carrier_errors = bfe->bfe_hw_stats.tx_carrier_lost; /* txerr += bfe->bfe_hw_stats.tx_carrier_lost; */ bfe->bfe_stats.ether_stat_ex_collisions = bfe->bfe_hw_stats.tx_excessive_cols; txerr += bfe->bfe_hw_stats.tx_excessive_cols; coll += bfe->bfe_hw_stats.tx_excessive_cols; bfe->bfe_stats.ether_stat_fcs_errors = bfe->bfe_hw_stats.rx_crc_errs; rxerr += bfe->bfe_hw_stats.rx_crc_errs; bfe->bfe_stats.ether_stat_first_collisions = bfe->bfe_hw_stats.tx_single_cols; coll += bfe->bfe_hw_stats.tx_single_cols; bfe->bfe_stats.ether_stat_multi_collisions = bfe->bfe_hw_stats.tx_multiple_cols; coll += bfe->bfe_hw_stats.tx_multiple_cols; bfe->bfe_stats.ether_stat_toolong_errors = bfe->bfe_hw_stats.rx_oversize_pkts; rxerr += bfe->bfe_hw_stats.rx_oversize_pkts; bfe->bfe_stats.ether_stat_tooshort_errors = bfe->bfe_hw_stats.rx_undersize; rxerr += bfe->bfe_hw_stats.rx_undersize; bfe->bfe_stats.ether_stat_tx_late_collisions += bfe->bfe_hw_stats.tx_late_cols; bfe->bfe_stats.ether_stat_defer_xmts += bfe->bfe_hw_stats.tx_defered; bfe->bfe_stats.ether_stat_macrcv_errors += rxerr; bfe->bfe_stats.ether_stat_macxmt_errors += txerr; bfe->bfe_stats.collisions += coll; } /* * Gets the state for dladm command and all. */ int bfe_mac_getstat(void *arg, uint_t stat, uint64_t *val) { bfe_t *bfe = (bfe_t *)arg; uint64_t v; int err = 0; rw_enter(&bfe->bfe_rwlock, RW_READER); switch (stat) { default: err = ENOTSUP; break; case MAC_STAT_IFSPEED: /* * MAC layer will ask for IFSPEED first and hence we * collect it only once. */ if (bfe->bfe_chip_state == BFE_CHIP_ACTIVE) { /* * Update stats from the hardware. */ bfe_gather_stats(bfe); } v = bfe->bfe_chip.speed; break; case ETHER_STAT_ADV_CAP_100T4: v = bfe->bfe_adv_100T4; break; case ETHER_STAT_ADV_CAP_100FDX: v = (bfe->bfe_mii_anar & MII_ABILITY_100BASE_TX_FD) != 0; break; case ETHER_STAT_ADV_CAP_100HDX: v = (bfe->bfe_mii_anar & MII_ABILITY_100BASE_TX) != 0; break; case ETHER_STAT_ADV_CAP_10FDX: v = (bfe->bfe_mii_anar & MII_ABILITY_10BASE_T_FD) != 0; break; case ETHER_STAT_ADV_CAP_10HDX: v = (bfe->bfe_mii_anar & MII_ABILITY_10BASE_T) != 0; break; case ETHER_STAT_ADV_CAP_ASMPAUSE: v = 0; break; case ETHER_STAT_ADV_CAP_AUTONEG: v = bfe->bfe_adv_aneg; break; case ETHER_STAT_ADV_CAP_PAUSE: v = (bfe->bfe_mii_anar & MII_ABILITY_PAUSE) != 0; break; case ETHER_STAT_ADV_REMFAULT: v = (bfe->bfe_mii_anar & MII_AN_ADVERT_REMFAULT) != 0; break; case ETHER_STAT_ALIGN_ERRORS: /* MIB */ v = bfe->bfe_stats.ether_stat_align_errors; break; case ETHER_STAT_CAP_100T4: v = (bfe->bfe_mii_bmsr & MII_STATUS_100_BASE_T4) != 0; break; case ETHER_STAT_CAP_100FDX: v = (bfe->bfe_mii_bmsr & MII_STATUS_100_BASEX_FD) != 0; break; case ETHER_STAT_CAP_100HDX: v = (bfe->bfe_mii_bmsr & MII_STATUS_100_BASEX) != 0; break; case ETHER_STAT_CAP_10FDX: v = (bfe->bfe_mii_bmsr & MII_STATUS_10_FD) != 0; break; case ETHER_STAT_CAP_10HDX: v = (bfe->bfe_mii_bmsr & MII_STATUS_10) != 0; break; case ETHER_STAT_CAP_ASMPAUSE: v = 0; break; case ETHER_STAT_CAP_AUTONEG: v = ((bfe->bfe_mii_bmsr & MII_STATUS_CANAUTONEG) != 0); break; case ETHER_STAT_CAP_PAUSE: v = 1; break; case ETHER_STAT_CAP_REMFAULT: v = (bfe->bfe_mii_bmsr & MII_STATUS_REMFAULT) != 0; break; case ETHER_STAT_CARRIER_ERRORS: v = bfe->bfe_stats.ether_stat_carrier_errors; break; case ETHER_STAT_JABBER_ERRORS: err = ENOTSUP; break; case ETHER_STAT_DEFER_XMTS: v = bfe->bfe_stats.ether_stat_defer_xmts; break; case ETHER_STAT_EX_COLLISIONS: /* MIB */ v = bfe->bfe_stats.ether_stat_ex_collisions; break; case ETHER_STAT_FCS_ERRORS: /* MIB */ v = bfe->bfe_stats.ether_stat_fcs_errors; break; case ETHER_STAT_FIRST_COLLISIONS: /* MIB */ v = bfe->bfe_stats.ether_stat_first_collisions; break; case ETHER_STAT_LINK_ASMPAUSE: v = 0; break; case ETHER_STAT_LINK_AUTONEG: v = (bfe->bfe_mii_bmcr & MII_CONTROL_ANE) != 0 && (bfe->bfe_mii_bmsr & MII_STATUS_ANDONE) != 0; break; case ETHER_STAT_LINK_DUPLEX: v = bfe->bfe_chip.duplex; break; case ETHER_STAT_LP_CAP_100T4: v = (bfe->bfe_mii_anlpar & MII_ABILITY_100BASE_T4) != 0; break; case ETHER_STAT_LP_CAP_100FDX: v = (bfe->bfe_mii_anlpar & MII_ABILITY_100BASE_TX_FD) != 0; break; case ETHER_STAT_LP_CAP_100HDX: v = (bfe->bfe_mii_anlpar & MII_ABILITY_100BASE_TX) != 0; break; case ETHER_STAT_LP_CAP_10FDX: v = (bfe->bfe_mii_anlpar & MII_ABILITY_10BASE_T_FD) != 0; break; case ETHER_STAT_LP_CAP_10HDX: v = (bfe->bfe_mii_anlpar & MII_ABILITY_10BASE_T) != 0; break; case ETHER_STAT_LP_CAP_ASMPAUSE: v = 0; break; case ETHER_STAT_LP_CAP_AUTONEG: v = (bfe->bfe_mii_exp & MII_AN_EXP_LPCANAN) != 0; break; case ETHER_STAT_LP_CAP_PAUSE: v = (bfe->bfe_mii_anlpar & MII_ABILITY_PAUSE) != 0; break; case ETHER_STAT_LP_REMFAULT: v = (bfe->bfe_mii_anlpar & MII_STATUS_REMFAULT) != 0; break; case ETHER_STAT_MACRCV_ERRORS: v = bfe->bfe_stats.ether_stat_macrcv_errors; break; case ETHER_STAT_MACXMT_ERRORS: v = bfe->bfe_stats.ether_stat_macxmt_errors; break; case ETHER_STAT_MULTI_COLLISIONS: v = bfe->bfe_stats.ether_stat_multi_collisions; break; case ETHER_STAT_SQE_ERRORS: err = ENOTSUP; break; case ETHER_STAT_TOOLONG_ERRORS: v = bfe->bfe_stats.ether_stat_toolong_errors; break; case ETHER_STAT_TOOSHORT_ERRORS: v = bfe->bfe_stats.ether_stat_tooshort_errors; break; case ETHER_STAT_TX_LATE_COLLISIONS: v = bfe->bfe_stats.ether_stat_tx_late_collisions; break; case ETHER_STAT_XCVR_ADDR: v = bfe->bfe_phy_addr; break; case ETHER_STAT_XCVR_ID: v = bfe->bfe_phy_id; break; case MAC_STAT_BRDCSTRCV: v = bfe->bfe_stats.brdcstrcv; break; case MAC_STAT_BRDCSTXMT: v = bfe->bfe_stats.brdcstxmt; break; case MAC_STAT_MULTIXMT: v = bfe->bfe_stats.multixmt; break; case MAC_STAT_COLLISIONS: v = bfe->bfe_stats.collisions; break; case MAC_STAT_IERRORS: v = bfe->bfe_stats.ierrors; break; case MAC_STAT_IPACKETS: v = bfe->bfe_stats.ipackets; break; case MAC_STAT_MULTIRCV: v = bfe->bfe_stats.multircv; break; case MAC_STAT_NORCVBUF: v = bfe->bfe_stats.norcvbuf; break; case MAC_STAT_NOXMTBUF: v = bfe->bfe_stats.noxmtbuf; break; case MAC_STAT_OBYTES: v = bfe->bfe_stats.obytes; break; case MAC_STAT_OERRORS: /* MIB */ v = bfe->bfe_stats.ether_stat_macxmt_errors; break; case MAC_STAT_OPACKETS: v = bfe->bfe_stats.opackets; break; case MAC_STAT_RBYTES: v = bfe->bfe_stats.rbytes; break; case MAC_STAT_UNDERFLOWS: v = bfe->bfe_stats.underflows; break; case MAC_STAT_OVERFLOWS: v = bfe->bfe_stats.overflows; break; } rw_exit(&bfe->bfe_rwlock); *val = v; return (err); } /*ARGSUSED*/ int bfe_mac_getprop(void *arg, const char *name, mac_prop_id_t num, uint_t flags, uint_t sz, void *val, uint_t *perm) { bfe_t *bfe = (bfe_t *)arg; int err = 0; boolean_t dfl = flags & MAC_PROP_DEFAULT; if (sz == 0) return (EINVAL); *perm = MAC_PROP_PERM_RW; switch (num) { case MAC_PROP_DUPLEX: *perm = MAC_PROP_PERM_READ; if (sz >= sizeof (link_duplex_t)) { bcopy(&bfe->bfe_chip.duplex, val, sizeof (link_duplex_t)); } else { err = EINVAL; } break; case MAC_PROP_SPEED: *perm = MAC_PROP_PERM_READ; if (sz >= sizeof (uint64_t)) { bcopy(&bfe->bfe_chip.speed, val, sizeof (uint64_t)); } else { err = EINVAL; } break; case MAC_PROP_AUTONEG: *(uint8_t *)val = dfl ? bfe->bfe_cap_aneg : bfe->bfe_adv_aneg; break; case MAC_PROP_ADV_100FDX_CAP: *perm = MAC_PROP_PERM_READ; *(uint8_t *)val = dfl ? bfe->bfe_cap_100fdx : bfe->bfe_adv_100fdx; break; case MAC_PROP_EN_100FDX_CAP: *(uint8_t *)val = dfl ? bfe->bfe_cap_100fdx : bfe->bfe_adv_100fdx; break; case MAC_PROP_ADV_100HDX_CAP: *perm = MAC_PROP_PERM_READ; *(uint8_t *)val = dfl ? bfe->bfe_cap_100hdx : bfe->bfe_adv_100hdx; break; case MAC_PROP_EN_100HDX_CAP: *(uint8_t *)val = dfl ? bfe->bfe_cap_100hdx : bfe->bfe_adv_100hdx; break; case MAC_PROP_ADV_10FDX_CAP: *perm = MAC_PROP_PERM_READ; *(uint8_t *)val = dfl ? bfe->bfe_cap_10fdx : bfe->bfe_adv_10fdx; break; case MAC_PROP_EN_10FDX_CAP: *(uint8_t *)val = dfl ? bfe->bfe_cap_10fdx : bfe->bfe_adv_10fdx; break; case MAC_PROP_ADV_10HDX_CAP: *perm = MAC_PROP_PERM_READ; *(uint8_t *)val = dfl ? bfe->bfe_cap_10hdx : bfe->bfe_adv_10hdx; break; case MAC_PROP_EN_10HDX_CAP: *(uint8_t *)val = dfl ? bfe->bfe_cap_10hdx : bfe->bfe_adv_10hdx; break; case MAC_PROP_ADV_100T4_CAP: *perm = MAC_PROP_PERM_READ; *(uint8_t *)val = dfl ? bfe->bfe_cap_100T4 : bfe->bfe_adv_100T4; break; case MAC_PROP_EN_100T4_CAP: *(uint8_t *)val = dfl ? bfe->bfe_cap_100T4 : bfe->bfe_adv_100T4; break; default: err = ENOTSUP; } return (err); } /*ARGSUSED*/ int bfe_mac_setprop(void *arg, const char *name, mac_prop_id_t num, uint_t sz, const void *val) { bfe_t *bfe = (bfe_t *)arg; uint8_t *advp; uint8_t *capp; int r = 0; switch (num) { case MAC_PROP_EN_100FDX_CAP: advp = &bfe->bfe_adv_100fdx; capp = &bfe->bfe_cap_100fdx; break; case MAC_PROP_EN_100HDX_CAP: advp = &bfe->bfe_adv_100hdx; capp = &bfe->bfe_cap_100hdx; break; case MAC_PROP_EN_10FDX_CAP: advp = &bfe->bfe_adv_10fdx; capp = &bfe->bfe_cap_10fdx; break; case MAC_PROP_EN_10HDX_CAP: advp = &bfe->bfe_adv_10hdx; capp = &bfe->bfe_cap_10hdx; break; case MAC_PROP_EN_100T4_CAP: advp = &bfe->bfe_adv_100T4; capp = &bfe->bfe_cap_100T4; break; case MAC_PROP_AUTONEG: advp = &bfe->bfe_adv_aneg; capp = &bfe->bfe_cap_aneg; break; default: return (ENOTSUP); } if (*capp == 0) return (ENOTSUP); bfe_grab_locks(bfe); if (*advp != *(const uint8_t *)val) { *advp = *(const uint8_t *)val; bfe->bfe_chip_action = BFE_ACTION_RESTART_SETPROP; if (bfe->bfe_chip_state == BFE_CHIP_ACTIVE) { /* * We need to stop the timer before grabbing locks * otherwise we can land-up in deadlock with untimeout. */ bfe_stop_timer(bfe); bfe->bfe_chip_action |= BFE_ACTION_RESTART; bfe_chip_restart(bfe); /* * We leave SETPROP because properties can be * temporary. */ bfe->bfe_chip_action &= ~(BFE_ACTION_RESTART); r = 1; } } bfe_release_locks(bfe); /* kick-off a potential stopped downstream */ if (r) mac_tx_update(bfe->bfe_machdl); return (0); } int bfe_mac_set_ether_addr(void *arg, const uint8_t *ea) { bfe_t *bfe = (bfe_t *)arg; bfe_grab_locks(bfe); bcopy(ea, bfe->bfe_ether_addr, ETHERADDRL); bfe_set_rx_mode(bfe); bfe_release_locks(bfe); return (0); } int bfe_mac_start(void *arg) { bfe_t *bfe = (bfe_t *)arg; bfe_grab_locks(bfe); if (bfe_chip_start(bfe) == DDI_FAILURE) { bfe_release_locks(bfe); return (EINVAL); } bfe_release_locks(bfe); mac_tx_update(bfe->bfe_machdl); return (0); } void bfe_mac_stop(void *arg) { bfe_t *bfe = (bfe_t *)arg; /* * We need to stop the timer before grabbing locks otherwise * we can land-up in deadlock with untimeout. */ bfe_stop_timer(bfe); bfe_grab_locks(bfe); /* * First halt the chip by disabling interrupts. */ bfe_chip_halt(bfe); bfe_stop_phy(bfe); bfe->bfe_chip_state = BFE_CHIP_STOPPED; /* * This will leave the PHY running. */ bfe_chip_reset(bfe); /* * Disable RX register. */ bfe->bfe_chip_mode &= ~BFE_RX_MODE_ENABLE; bfe_set_rx_mode(bfe); bfe_release_locks(bfe); } /* * Send a packet down the wire. */ static int bfe_send_a_packet(bfe_t *bfe, mblk_t *mp) { bfe_ring_t *r = &bfe->bfe_tx_ring; uint32_t cur = r->r_curr_desc; uint32_t next; size_t pktlen = msgsize(mp); uchar_t *buf; uint32_t v; ASSERT(MUTEX_HELD(&r->r_lock)); ASSERT(mp != NULL); if (pktlen > r->r_buf_len) { freemsg(mp); return (BFE_SUCCESS); } /* * There is a big reason why we don't check for '0'. It becomes easy * for us to not roll over the ring since we are based on producer (tx) * and consumer (reclaim by an interrupt) model. Especially when we * run out of TX descriptor, chip will send a single interrupt and * both producer and consumer counter will be same. So we keep a * difference of 1 always. */ if (r->r_avail_desc <= 1) { bfe->bfe_stats.noxmtbuf++; bfe->bfe_tx_resched = 1; return (BFE_FAILURE); } /* * Get the DMA buffer to hold packet. */ buf = (uchar_t *)r->r_buf_dma[cur].addr; mcopymsg(mp, buf); /* it also frees mp */ /* * Gather statistics. */ if (buf[0] & 0x1) { if (bcmp(buf, bfe_broadcast, ETHERADDRL) != 0) bfe->bfe_stats.multixmt++; else bfe->bfe_stats.brdcstxmt++; } bfe->bfe_stats.opackets++; bfe->bfe_stats.obytes += pktlen; /* * Program the DMA descriptor (start and end of frame are same). */ next = cur; v = (pktlen & BFE_DESC_LEN) | BFE_DESC_IOC | BFE_DESC_SOF | BFE_DESC_EOF; if (cur == (TX_NUM_DESC - 1)) v |= BFE_DESC_EOT; PUT_DESC(r, (uint32_t *)&(r->r_desc[cur].desc_ctl), v); /* * DMA addresses need to be added to BFE_PCI_DMA */ PUT_DESC(r, (uint32_t *)&(r->r_desc[cur].desc_addr), (r->r_buf_dma[cur].cookie.dmac_laddress + BFE_PCI_DMA)); /* * Sync the packet data for the device. */ (void) SYNC_BUF(r, cur, 0, pktlen, DDI_DMA_SYNC_FORDEV); /* Move to next descriptor slot */ BFE_INC_SLOT(next, TX_NUM_DESC); (void) SYNC_DESC(r, 0, r->r_ndesc, DDI_DMA_SYNC_FORDEV); r->r_curr_desc = next; /* * The order should be 1,2,3,... for BFE_DMATX_PTR if 0,1,2,3,... * descriptor slot are being programmed. */ OUTL(bfe, BFE_DMATX_PTR, next * sizeof (bfe_desc_t)); FLUSH(bfe, BFE_DMATX_PTR); r->r_avail_desc--; /* * Let timeout know that it must reset the chip if a * packet is not sent down the wire for more than 5 seconds. */ bfe->bfe_tx_stall_time = gethrtime() + (5 * 1000000000ULL); return (BFE_SUCCESS); } mblk_t * bfe_mac_transmit_packet(void *arg, mblk_t *mp) { bfe_t *bfe = (bfe_t *)arg; bfe_ring_t *r = &bfe->bfe_tx_ring; mblk_t *nmp; mutex_enter(&r->r_lock); if (bfe->bfe_chip_state != BFE_CHIP_ACTIVE) { DTRACE_PROBE1(tx__chip__not__active, int, bfe->bfe_unit); freemsgchain(mp); mutex_exit(&r->r_lock); return (NULL); } while (mp != NULL) { nmp = mp->b_next; mp->b_next = NULL; if (bfe_send_a_packet(bfe, mp) == BFE_FAILURE) { mp->b_next = nmp; break; } mp = nmp; } mutex_exit(&r->r_lock); return (mp); } int bfe_mac_set_promisc(void *arg, boolean_t promiscflag) { bfe_t *bfe = (bfe_t *)arg; bfe_grab_locks(bfe); if (bfe->bfe_chip_state != BFE_CHIP_ACTIVE) { bfe_release_locks(bfe); return (EIO); } if (promiscflag) { /* Set Promiscous on */ bfe->bfe_chip_mode |= BFE_RX_MODE_PROMISC; } else { bfe->bfe_chip_mode &= ~BFE_RX_MODE_PROMISC; } bfe_set_rx_mode(bfe); bfe_release_locks(bfe); return (0); } int bfe_mac_set_multicast(void *arg, boolean_t add, const uint8_t *macaddr) { /* * It was too much of pain to implement multicast in CAM. Instead * we never disable multicast filter. */ return (0); } static mac_callbacks_t bfe_mac_callbacks = { MC_SETPROP | MC_GETPROP, bfe_mac_getstat, /* gets stats */ bfe_mac_start, /* starts mac */ bfe_mac_stop, /* stops mac */ bfe_mac_set_promisc, /* sets promisc mode for snoop */ bfe_mac_set_multicast, /* multicast implementation */ bfe_mac_set_ether_addr, /* sets ethernet address (unicast) */ bfe_mac_transmit_packet, /* transmits packet */ NULL, /* ioctl */ NULL, /* getcap */ NULL, /* open */ NULL, /* close */ bfe_mac_setprop, bfe_mac_getprop, }; static void bfe_error_handler(bfe_t *bfe, int intr_mask) { uint32_t v; if (intr_mask & BFE_ISTAT_RFO) { bfe->bfe_stats.overflows++; bfe->bfe_chip_action |= (BFE_ACTION_RESTART | BFE_ACTION_RESTART_FAULT); goto action; } if (intr_mask & BFE_ISTAT_TFU) { bfe->bfe_stats.underflows++; return; } /* Descriptor Protocol Error */ if (intr_mask & BFE_ISTAT_DPE) { bfe_error(bfe->bfe_dip, "Descriptor Protocol Error. Halting Chip"); bfe->bfe_chip_action |= (BFE_ACTION_RESTART | BFE_ACTION_RESTART_FAULT); goto action; } /* Descriptor Error */ if (intr_mask & BFE_ISTAT_DSCE && halt == 0) { bfe_error(bfe->bfe_dip, "Descriptor Error. Restarting Chip"); goto action; } /* Receive Descr. Underflow */ if (intr_mask & BFE_ISTAT_RDU) { bfe_error(bfe->bfe_dip, "Receive Descriptor Underflow. Restarting Chip"); bfe->bfe_stats.ether_stat_macrcv_errors++; bfe->bfe_chip_action |= (BFE_ACTION_RESTART | BFE_ACTION_RESTART_FAULT); goto action; } v = INL(bfe, BFE_DMATX_STAT); /* Error while sending a packet */ if (v & BFE_STAT_EMASK) { bfe->bfe_stats.ether_stat_macxmt_errors++; bfe_error(bfe->bfe_dip, "Error while sending a packet. Restarting Chip"); } /* Error while receiving a packet */ v = INL(bfe, BFE_DMARX_STAT); if (v & BFE_RX_FLAG_ERRORS) { bfe->bfe_stats.ierrors++; bfe_error(bfe->bfe_dip, "Error while receiving a packet. Restarting Chip"); } bfe->bfe_chip_action |= (BFE_ACTION_RESTART | BFE_ACTION_RESTART_FAULT); action: bfe_chip_halt(bfe); } /* * It will recycle a RX descriptor slot. */ static void bfe_rx_desc_buf_reinit(bfe_t *bfe, uint_t slot) { bfe_ring_t *r = &bfe->bfe_rx_ring; uint32_t v; slot %= RX_NUM_DESC; bzero(r->r_buf_dma[slot].addr, sizeof (bfe_rx_header_t)); (void) SYNC_BUF(r, slot, 0, BFE_RX_OFFSET, DDI_DMA_SYNC_FORDEV); v = r->r_buf_dma[slot].len & BFE_DESC_LEN; if (slot == (RX_NUM_DESC - 1)) v |= BFE_DESC_EOT; PUT_DESC(r, (uint32_t *)&(r->r_desc[slot].desc_ctl), v); /* * DMA addresses need to be added to BFE_PCI_DMA */ PUT_DESC(r, (uint32_t *)&(r->r_desc[slot].desc_addr), (r->r_buf_dma[slot].cookie.dmac_laddress + BFE_PCI_DMA)); } /* * Gets called from interrupt context to handle RX interrupt. */ static mblk_t * bfe_receive(bfe_t *bfe, int intr_mask) { int rxstat, current; mblk_t *mp = NULL, *rx_head, *rx_tail; uchar_t *rx_header; uint16_t len; uchar_t *bp; bfe_ring_t *r = &bfe->bfe_rx_ring; int i; rxstat = INL(bfe, BFE_DMARX_STAT); current = (rxstat & BFE_STAT_CDMASK) / sizeof (bfe_desc_t); i = r->r_curr_desc; rx_head = rx_tail = NULL; DTRACE_PROBE3(receive, int, bfe->bfe_unit, int, r->r_curr_desc, int, current); for (i = r->r_curr_desc; i != current; BFE_INC_SLOT(i, RX_NUM_DESC)) { /* * Sync the buffer associated with the descriptor table entry. */ (void) SYNC_BUF(r, i, 0, r->r_buf_dma[i].len, DDI_DMA_SYNC_FORKERNEL); rx_header = (void *)r->r_buf_dma[i].addr; /* * We do this to make sure we are endian neutral. Chip is * big endian. * * The header looks like :- * * Offset 0 -> uint16_t len * Offset 2 -> uint16_t flags * Offset 4 -> uint16_t pad[12] */ len = (rx_header[1] << 8) | rx_header[0]; len -= 4; /* CRC bytes need to be removed */ /* * Don't receive this packet if pkt length is greater than * MTU + VLAN_TAGSZ. */ if (len > r->r_buf_len) { /* Recycle slot for later use */ bfe_rx_desc_buf_reinit(bfe, i); continue; } if ((mp = allocb(len + VLAN_TAGSZ, BPRI_MED)) != NULL) { mp->b_rptr += VLAN_TAGSZ; bp = mp->b_rptr; mp->b_wptr = bp + len; /* sizeof (bfe_rx_header_t) + 2 */ bcopy(r->r_buf_dma[i].addr + BFE_RX_OFFSET, bp, len); mp->b_next = NULL; if (rx_tail == NULL) rx_head = rx_tail = mp; else { rx_tail->b_next = mp; rx_tail = mp; } /* Number of packets received so far */ bfe->bfe_stats.ipackets++; /* Total bytes of packets received so far */ bfe->bfe_stats.rbytes += len; if (bcmp(mp->b_rptr, bfe_broadcast, ETHERADDRL) == 0) bfe->bfe_stats.brdcstrcv++; else bfe->bfe_stats.multircv++; } else { bfe->bfe_stats.norcvbuf++; /* Recycle the slot for later use */ bfe_rx_desc_buf_reinit(bfe, i); break; } /* * Reinitialize the current descriptor slot's buffer so that * it can be reused. */ bfe_rx_desc_buf_reinit(bfe, i); } r->r_curr_desc = i; (void) SYNC_DESC(r, 0, r->r_ndesc, DDI_DMA_SYNC_FORDEV); return (rx_head); } static int bfe_tx_reclaim(bfe_ring_t *r) { uint32_t cur, start; uint32_t v; cur = INL(r->r_bfe, BFE_DMATX_STAT) & BFE_STAT_CDMASK; cur = cur / sizeof (bfe_desc_t); /* * Start with the last descriptor consumed by the chip. */ start = r->r_cons_desc; DTRACE_PROBE3(tx__reclaim, int, r->r_bfe->bfe_unit, int, start, int, cur); /* * There will be at least one descriptor to process. */ while (start != cur) { r->r_avail_desc++; v = r->r_buf_dma[start].len & BFE_DESC_LEN; if (start == (TX_NUM_DESC - 1)) v |= BFE_DESC_EOT; PUT_DESC(r, (uint32_t *)&(r->r_desc[start].desc_ctl), v); PUT_DESC(r, (uint32_t *)&(r->r_desc[start].desc_addr), (r->r_buf_dma[start].cookie.dmac_laddress + BFE_PCI_DMA)); /* Move to next descriptor in TX ring */ BFE_INC_SLOT(start, TX_NUM_DESC); } (void) ddi_dma_sync(r->r_desc_dma_handle, 0, (r->r_ndesc * sizeof (bfe_desc_t)), DDI_DMA_SYNC_FORDEV); r->r_cons_desc = start; /* consumed pointer */ r->r_bfe->bfe_tx_stall_time = 0; return (cur); } static int bfe_tx_done(bfe_t *bfe, int intr_mask) { bfe_ring_t *r = &bfe->bfe_tx_ring; int resched = 0; mutex_enter(&r->r_lock); (void) bfe_tx_reclaim(r); if (bfe->bfe_tx_resched) { resched = 1; bfe->bfe_tx_resched = 0; } mutex_exit(&r->r_lock); return (resched); } /* * ISR for interrupt handling */ static uint_t bfe_interrupt(caddr_t arg1, caddr_t arg2) { bfe_t *bfe = (void *)arg1; uint32_t intr_stat; mblk_t *rx_head = NULL; int resched = 0; /* * Grab the lock to avoid stopping the chip while this interrupt * is handled. */ rw_enter(&bfe->bfe_rwlock, RW_READER); /* * It's necessary to read intr stat again because masking interrupt * register does not really mask interrupts coming from the chip. */ intr_stat = INL(bfe, BFE_INTR_STAT); intr_stat &= BFE_IMASK_DEF; OUTL(bfe, BFE_INTR_STAT, intr_stat); (void) INL(bfe, BFE_INTR_STAT); if (intr_stat == 0) { rw_exit(&bfe->bfe_rwlock); return (DDI_INTR_UNCLAIMED); } DTRACE_PROBE2(bfe__interrupt, int, bfe->bfe_unit, int, intr_stat); if (bfe->bfe_chip_state != BFE_CHIP_ACTIVE) { /* * If chip is suspended then we just return. */ if (bfe->bfe_chip_state == BFE_CHIP_SUSPENDED) { rw_exit(&bfe->bfe_rwlock); DTRACE_PROBE1(interrupt__chip__is__suspend, int, bfe->bfe_unit); return (DDI_INTR_CLAIMED); } /* * Halt the chip again i.e basically disable interrupts. */ bfe_chip_halt(bfe); rw_exit(&bfe->bfe_rwlock); DTRACE_PROBE1(interrupt__chip__not__active, int, bfe->bfe_unit); return (DDI_INTR_CLAIMED); } /* A packet was received */ if (intr_stat & BFE_ISTAT_RX) { rx_head = bfe_receive(bfe, intr_stat); } /* A packet was sent down the wire */ if (intr_stat & BFE_ISTAT_TX) { resched = bfe_tx_done(bfe, intr_stat); } /* There was an error */ if (intr_stat & BFE_ISTAT_ERRORS) { bfe_error_handler(bfe, intr_stat); } rw_exit(&bfe->bfe_rwlock); /* * Pass the list of packets received from chip to MAC layer. */ if (rx_head) { mac_rx(bfe->bfe_machdl, 0, rx_head); } /* * Let the MAC start sending pkts to a potential stopped stream. */ if (resched) mac_tx_update(bfe->bfe_machdl); return (DDI_INTR_CLAIMED); } /* * Removes registered interrupt handler. */ static void bfe_remove_intr(bfe_t *bfe) { (void) ddi_intr_remove_handler(bfe->bfe_intrhdl); (void) ddi_intr_free(bfe->bfe_intrhdl); } /* * Add an interrupt for the driver. */ static int bfe_add_intr(bfe_t *bfe) { int nintrs = 1; int ret; ret = ddi_intr_alloc(bfe->bfe_dip, &bfe->bfe_intrhdl, DDI_INTR_TYPE_FIXED, /* type */ 0, /* inumber */ 1, /* count */ &nintrs, /* actual nintrs */ DDI_INTR_ALLOC_STRICT); if (ret != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "ddi_intr_alloc() failed" " : ret : %d", ret); return (DDI_FAILURE); } ret = ddi_intr_add_handler(bfe->bfe_intrhdl, bfe_interrupt, bfe, NULL); if (ret != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "ddi_intr_add_handler() failed"); (void) ddi_intr_free(bfe->bfe_intrhdl); return (DDI_FAILURE); } ret = ddi_intr_get_pri(bfe->bfe_intrhdl, &bfe->bfe_intrpri); if (ret != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "ddi_intr_get_pri() failed"); bfe_remove_intr(bfe); return (DDI_FAILURE); } return (DDI_SUCCESS); } /* * Identify chipset family. */ static int bfe_identify_hardware(bfe_t *bfe) { uint16_t vid, did; int i; vid = pci_config_get16(bfe->bfe_conf_handle, PCI_CONF_VENID); did = pci_config_get16(bfe->bfe_conf_handle, PCI_CONF_DEVID); for (i = 0; i < (sizeof (bfe_cards) / sizeof (bfe_cards_t)); i++) { if (bfe_cards[i].vendor_id == vid && bfe_cards[i].device_id == did) { return (BFE_SUCCESS); } } bfe_error(bfe->bfe_dip, "bfe driver is attaching to unknown pci%d,%d" " vendor/device-id card", vid, did); return (BFE_SUCCESS); } /* * Maps device registers. */ static int bfe_regs_map(bfe_t *bfe) { dev_info_t *dip = bfe->bfe_dip; int ret; ret = ddi_regs_map_setup(dip, 1, &bfe->bfe_mem_regset.addr, 0, 0, &bfe_dev_attr, &bfe->bfe_mem_regset.hdl); if (ret != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "ddi_regs_map_setup failed"); return (DDI_FAILURE); } return (DDI_SUCCESS); } static void bfe_unmap_regs(bfe_t *bfe) { ddi_regs_map_free(&bfe->bfe_mem_regset.hdl); } static int bfe_get_chip_config(bfe_t *bfe) { uint32_t prom[BFE_EEPROM_SIZE]; int i; /* * Read EEPROM in prom[] */ for (i = 0; i < BFE_EEPROM_SIZE; i++) { prom[i] = INL(bfe, BFE_EEPROM_BASE + i * sizeof (uint32_t)); } bfe->bfe_dev_addr[0] = bfe->bfe_ether_addr[0] = INB(bfe, BFE_EEPROM_BASE + 79); bfe->bfe_dev_addr[1] = bfe->bfe_ether_addr[1] = INB(bfe, BFE_EEPROM_BASE + 78); bfe->bfe_dev_addr[2] = bfe->bfe_ether_addr[2] = INB(bfe, BFE_EEPROM_BASE + 81); bfe->bfe_dev_addr[3] = bfe->bfe_ether_addr[3] = INB(bfe, BFE_EEPROM_BASE + 80); bfe->bfe_dev_addr[4] = bfe->bfe_ether_addr[4] = INB(bfe, BFE_EEPROM_BASE + 83); bfe->bfe_dev_addr[5] = bfe->bfe_ether_addr[5] = INB(bfe, BFE_EEPROM_BASE + 82); bfe->bfe_phy_addr = -1; return (DDI_SUCCESS); } /* * Ring Management routines */ static int bfe_ring_buf_alloc(bfe_t *bfe, bfe_ring_t *r, int slot, int d) { int err; uint_t count = 0; err = ddi_dma_alloc_handle(bfe->bfe_dip, &bfe_dma_attr_buf, DDI_DMA_SLEEP, NULL, &r->r_buf_dma[slot].handle); if (err != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, " bfe_ring_buf_alloc() :" " alloc_handle failed"); goto fail0; } err = ddi_dma_mem_alloc(r->r_buf_dma[slot].handle, r->r_buf_len, &bfe_buf_attr, DDI_DMA_STREAMING, DDI_DMA_SLEEP, NULL, &r->r_buf_dma[slot].addr, &r->r_buf_dma[slot].len, &r->r_buf_dma[slot].acchdl); if (err != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, " bfe_ring_buf_alloc() :" " mem_alloc failed :%d", err); goto fail1; } err = ddi_dma_addr_bind_handle(r->r_buf_dma[slot].handle, NULL, r->r_buf_dma[slot].addr, r->r_buf_dma[slot].len, (DDI_DMA_RDWR | DDI_DMA_STREAMING), DDI_DMA_SLEEP, NULL, &r->r_buf_dma[slot].cookie, &count); if (err != DDI_DMA_MAPPED) { bfe_error(bfe->bfe_dip, " bfe_ring_buf_alloc() :" " bind_handle failed"); goto fail2; } if (count > 1) { bfe_error(bfe->bfe_dip, " bfe_ring_buf_alloc() :" " more than one DMA cookie"); (void) ddi_dma_unbind_handle(r->r_buf_dma[slot].handle); goto fail2; } return (DDI_SUCCESS); fail2: ddi_dma_mem_free(&r->r_buf_dma[slot].acchdl); fail1: ddi_dma_free_handle(&r->r_buf_dma[slot].handle); fail0: return (DDI_FAILURE); } static void bfe_ring_buf_free(bfe_ring_t *r, int slot) { if (r->r_buf_dma == NULL) return; (void) ddi_dma_unbind_handle(r->r_buf_dma[slot].handle); ddi_dma_mem_free(&r->r_buf_dma[slot].acchdl); ddi_dma_free_handle(&r->r_buf_dma[slot].handle); } static void bfe_buffer_free(bfe_ring_t *r) { int i; for (i = 0; i < r->r_ndesc; i++) { bfe_ring_buf_free(r, i); } } static void bfe_ring_desc_free(bfe_ring_t *r) { (void) ddi_dma_unbind_handle(r->r_desc_dma_handle); ddi_dma_mem_free(&r->r_desc_acc_handle); ddi_dma_free_handle(&r->r_desc_dma_handle); kmem_free(r->r_buf_dma, r->r_ndesc * sizeof (bfe_dma_t)); r->r_buf_dma = NULL; r->r_desc = NULL; } static int bfe_ring_desc_alloc(bfe_t *bfe, bfe_ring_t *r, int d) { int err, i, fail = 0; caddr_t ring; size_t size_krnl = 0, size_dma = 0, ring_len = 0; ddi_dma_cookie_t cookie; uint_t count = 0; ASSERT(bfe != NULL); size_krnl = r->r_ndesc * sizeof (bfe_dma_t); size_dma = r->r_ndesc * sizeof (bfe_desc_t); r->r_buf_dma = kmem_zalloc(size_krnl, KM_SLEEP); err = ddi_dma_alloc_handle(bfe->bfe_dip, &bfe_dma_attr_desc, DDI_DMA_SLEEP, NULL, &r->r_desc_dma_handle); if (err != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "bfe_ring_desc_alloc() failed on" " ddi_dma_alloc_handle()"); kmem_free(r->r_buf_dma, size_krnl); return (DDI_FAILURE); } err = ddi_dma_mem_alloc(r->r_desc_dma_handle, size_dma, &bfe_buf_attr, DDI_DMA_CONSISTENT, DDI_DMA_SLEEP, NULL, &ring, &ring_len, &r->r_desc_acc_handle); if (err != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "bfe_ring_desc_alloc() failed on" " ddi_dma_mem_alloc()"); ddi_dma_free_handle(&r->r_desc_dma_handle); kmem_free(r->r_buf_dma, size_krnl); return (DDI_FAILURE); } err = ddi_dma_addr_bind_handle(r->r_desc_dma_handle, NULL, ring, ring_len, DDI_DMA_RDWR | DDI_DMA_CONSISTENT, DDI_DMA_SLEEP, NULL, &cookie, &count); if (err != DDI_SUCCESS) { bfe_error(bfe->bfe_dip, "bfe_ring_desc_alloc() failed on" " ddi_dma_addr_bind_handle()"); ddi_dma_mem_free(&r->r_desc_acc_handle); ddi_dma_free_handle(&r->r_desc_dma_handle); kmem_free(r->r_buf_dma, size_krnl); return (DDI_FAILURE); } /* * We don't want to have multiple cookies. Descriptor should be * aligned to PAGESIZE boundary. */ ASSERT(count == 1); /* The actual descriptor for the ring */ r->r_desc_len = ring_len; r->r_desc_cookie = cookie; r->r_desc = (void *)ring; bzero(r->r_desc, size_dma); bzero(r->r_desc, ring_len); /* For each descriptor, allocate a DMA buffer */ fail = 0; for (i = 0; i < r->r_ndesc; i++) { if (bfe_ring_buf_alloc(bfe, r, i, d) != DDI_SUCCESS) { i--; fail = 1; break; } } if (fail) { while (i-- >= 0) { bfe_ring_buf_free(r, i); } /* We don't need the descriptor anymore */ bfe_ring_desc_free(r); return (DDI_FAILURE); } return (DDI_SUCCESS); } static int bfe_rings_alloc(bfe_t *bfe) { /* TX */ mutex_init(&bfe->bfe_tx_ring.r_lock, NULL, MUTEX_DRIVER, NULL); bfe->bfe_tx_ring.r_lockp = &bfe->bfe_tx_ring.r_lock; bfe->bfe_tx_ring.r_buf_len = BFE_MTU + sizeof (struct ether_header) + VLAN_TAGSZ + ETHERFCSL; bfe->bfe_tx_ring.r_ndesc = TX_NUM_DESC; bfe->bfe_tx_ring.r_bfe = bfe; bfe->bfe_tx_ring.r_avail_desc = TX_NUM_DESC; /* RX */ mutex_init(&bfe->bfe_rx_ring.r_lock, NULL, MUTEX_DRIVER, NULL); bfe->bfe_rx_ring.r_lockp = &bfe->bfe_rx_ring.r_lock; bfe->bfe_rx_ring.r_buf_len = BFE_MTU + sizeof (struct ether_header) + VLAN_TAGSZ + ETHERFCSL + RX_HEAD_ROOM; bfe->bfe_rx_ring.r_ndesc = RX_NUM_DESC; bfe->bfe_rx_ring.r_bfe = bfe; bfe->bfe_rx_ring.r_avail_desc = RX_NUM_DESC; /* Allocate TX Ring */ if (bfe_ring_desc_alloc(bfe, &bfe->bfe_tx_ring, DDI_DMA_WRITE) != DDI_SUCCESS) return (DDI_FAILURE); /* Allocate RX Ring */ if (bfe_ring_desc_alloc(bfe, &bfe->bfe_rx_ring, DDI_DMA_READ) != DDI_SUCCESS) { cmn_err(CE_NOTE, "RX ring allocation failed"); bfe_ring_desc_free(&bfe->bfe_tx_ring); return (DDI_FAILURE); } bfe->bfe_tx_ring.r_flags = BFE_RING_ALLOCATED; bfe->bfe_rx_ring.r_flags = BFE_RING_ALLOCATED; return (DDI_SUCCESS); } static int bfe_resume(dev_info_t *dip) { bfe_t *bfe; int err = DDI_SUCCESS; if ((bfe = ddi_get_driver_private(dip)) == NULL) { bfe_error(dip, "Unexpected error (no driver private data)" " while resume"); return (DDI_FAILURE); } /* * Grab all the locks first. */ bfe_grab_locks(bfe); bfe->bfe_chip_state = BFE_CHIP_RESUME; bfe_init_vars(bfe); /* PHY will also start running */ bfe_chip_reset(bfe); if (bfe_chip_start(bfe) == DDI_FAILURE) { bfe_error(dip, "Could not resume chip"); err = DDI_FAILURE; } bfe_release_locks(bfe); if (err == DDI_SUCCESS) mac_tx_update(bfe->bfe_machdl); return (err); } static int bfe_attach(dev_info_t *dip, ddi_attach_cmd_t cmd) { int unit; bfe_t *bfe; mac_register_t *macreg; int ret; switch (cmd) { case DDI_RESUME: return (bfe_resume(dip)); case DDI_ATTACH: break; default: return (DDI_FAILURE); } unit = ddi_get_instance(dip); bfe = kmem_zalloc(sizeof (bfe_t), KM_SLEEP); bfe->bfe_dip = dip; bfe->bfe_unit = unit; if (pci_config_setup(dip, &bfe->bfe_conf_handle) != DDI_SUCCESS) { bfe_error(dip, "pci_config_setup failed"); goto fail0; } /* * Enable IO space, Bus Master and Memory Space accessess. */ ret = pci_config_get16(bfe->bfe_conf_handle, PCI_CONF_COMM); pci_config_put16(bfe->bfe_conf_handle, PCI_CONF_COMM, PCI_COMM_IO | PCI_COMM_MAE | PCI_COMM_ME | ret); ddi_set_driver_private(dip, bfe); /* Identify hardware */ if (bfe_identify_hardware(bfe) == BFE_FAILURE) { bfe_error(dip, "Could not identify device"); goto fail1; } if (bfe_regs_map(bfe) != DDI_SUCCESS) { bfe_error(dip, "Could not map device registers"); goto fail1; } (void) bfe_get_chip_config(bfe); /* * Register with MAC layer */ if ((macreg = mac_alloc(MAC_VERSION)) == NULL) { bfe_error(dip, "mac_alloc() failed"); goto fail2; } macreg->m_type_ident = MAC_PLUGIN_IDENT_ETHER; macreg->m_driver = bfe; macreg->m_dip = dip; macreg->m_instance = unit; macreg->m_src_addr = bfe->bfe_ether_addr; macreg->m_callbacks = &bfe_mac_callbacks; macreg->m_min_sdu = 0; macreg->m_max_sdu = ETHERMTU; macreg->m_margin = VLAN_TAGSZ; if ((ret = mac_register(macreg, &bfe->bfe_machdl)) != 0) { bfe_error(dip, "mac_register() failed with %d error", ret); mac_free(macreg); goto fail2; } mac_free(macreg); rw_init(&bfe->bfe_rwlock, NULL, RW_DRIVER, DDI_INTR_PRI(bfe->bfe_intrpri)); if (bfe_add_intr(bfe) != DDI_SUCCESS) { bfe_error(dip, "Could not add interrupt"); goto fail3; } if (bfe_rings_alloc(bfe) != DDI_SUCCESS) { bfe_error(dip, "Could not allocate TX/RX Ring"); goto fail4; } /* Init and then reset the chip */ bfe->bfe_chip_action = 0; bfe_init_vars(bfe); /* PHY will also start running */ bfe_chip_reset(bfe); /* * Even though we enable the interrupts here but chip's interrupt * is not enabled yet. It will be enabled once we plumb the interface. */ if (ddi_intr_enable(bfe->bfe_intrhdl) != DDI_SUCCESS) { bfe_error(dip, "Could not enable interrupt"); goto fail4; } return (DDI_SUCCESS); fail4: bfe_remove_intr(bfe); fail3: (void) mac_unregister(bfe->bfe_machdl); fail2: bfe_unmap_regs(bfe); fail1: pci_config_teardown(&bfe->bfe_conf_handle); fail0: kmem_free(bfe, sizeof (bfe_t)); return (DDI_FAILURE); } static int bfe_detach(dev_info_t *devinfo, ddi_detach_cmd_t cmd) { bfe_t *bfe; bfe = ddi_get_driver_private(devinfo); switch (cmd) { case DDI_DETACH: /* * We need to stop the timer before grabbing locks otherwise * we can land-up in deadlock with untimeout. */ bfe_stop_timer(bfe); /* * First unregister with MAC layer before stopping DMA * engine. */ if (mac_unregister(bfe->bfe_machdl) != DDI_SUCCESS) return (DDI_FAILURE); bfe->bfe_machdl = NULL; /* * Quiesce the chip first. */ bfe_grab_locks(bfe); bfe_chip_halt(bfe); bfe_stop_phy(bfe); bfe_release_locks(bfe); (void) ddi_intr_disable(bfe->bfe_intrhdl); /* Make sure timer is gone. */ bfe_stop_timer(bfe); /* * Free the DMA resources for buffer and then descriptors */ if (bfe->bfe_tx_ring.r_flags == BFE_RING_ALLOCATED) { /* TX */ bfe_buffer_free(&bfe->bfe_tx_ring); bfe_ring_desc_free(&bfe->bfe_tx_ring); } if (bfe->bfe_rx_ring.r_flags == BFE_RING_ALLOCATED) { /* RX */ bfe_buffer_free(&bfe->bfe_rx_ring); bfe_ring_desc_free(&bfe->bfe_rx_ring); } bfe_remove_intr(bfe); bfe_unmap_regs(bfe); pci_config_teardown(&bfe->bfe_conf_handle); mutex_destroy(&bfe->bfe_tx_ring.r_lock); mutex_destroy(&bfe->bfe_rx_ring.r_lock); rw_destroy(&bfe->bfe_rwlock); kmem_free(bfe, sizeof (bfe_t)); ddi_set_driver_private(devinfo, NULL); return (DDI_SUCCESS); case DDI_SUSPEND: /* * We need to stop the timer before grabbing locks otherwise * we can land-up in deadlock with untimeout. */ bfe_stop_timer(bfe); /* * Grab all the locks first. */ bfe_grab_locks(bfe); bfe_chip_halt(bfe); bfe_stop_phy(bfe); bfe->bfe_chip_state = BFE_CHIP_SUSPENDED; bfe_release_locks(bfe); return (DDI_SUCCESS); default: return (DDI_FAILURE); } } /* * Quiesce the card for fast reboot */ int bfe_quiesce(dev_info_t *dev_info) { bfe_t *bfe; bfe = ddi_get_driver_private(dev_info); bfe_chip_halt(bfe); bfe_stop_phy(bfe); bfe->bfe_chip_state = BFE_CHIP_QUIESCED; return (DDI_SUCCESS); } static struct cb_ops bfe_cb_ops = { nulldev, /* cb_open */ nulldev, /* cb_close */ nodev, /* cb_strategy */ nodev, /* cb_print */ nodev, /* cb_dump */ nodev, /* cb_read */ nodev, /* cb_write */ nodev, /* cb_ioctl */ nodev, /* cb_devmap */ nodev, /* cb_mmap */ nodev, /* cb_segmap */ nochpoll, /* cb_chpoll */ ddi_prop_op, /* cb_prop_op */ NULL, /* cb_stream */ D_MP | D_HOTPLUG, /* cb_flag */ CB_REV, /* cb_rev */ nodev, /* cb_aread */ nodev /* cb_awrite */ }; static struct dev_ops bfe_dev_ops = { DEVO_REV, /* devo_rev */ 0, /* devo_refcnt */ NULL, /* devo_getinfo */ nulldev, /* devo_identify */ nulldev, /* devo_probe */ bfe_attach, /* devo_attach */ bfe_detach, /* devo_detach */ nodev, /* devo_reset */ &bfe_cb_ops, /* devo_cb_ops */ NULL, /* devo_bus_ops */ ddi_power, /* devo_power */ bfe_quiesce /* devo_quiesce */ }; static struct modldrv bfe_modldrv = { &mod_driverops, bfe_ident, &bfe_dev_ops }; static struct modlinkage modlinkage = { MODREV_1, (void *)&bfe_modldrv, NULL }; int _info(struct modinfo *modinfop) { return (mod_info(&modlinkage, modinfop)); } int _init(void) { int status; mac_init_ops(&bfe_dev_ops, MODULE_NAME); status = mod_install(&modlinkage); if (status == DDI_FAILURE) mac_fini_ops(&bfe_dev_ops); return (status); } int _fini(void) { int status; status = mod_remove(&modlinkage); if (status == 0) { mac_fini_ops(&bfe_dev_ops); } return (status); }