// SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2020 NXP * Copyright 2022 Pengutronix, Lucas Stach */ #include #include #include #include #include #include #include #include #include #define PHY_REG(reg) (reg * 4) #define REG01_PMS_P_MASK GENMASK(3, 0) #define REG03_PMS_S_MASK GENMASK(7, 4) #define REG12_CK_DIV_MASK GENMASK(5, 4) #define REG13_TG_CODE_LOW_MASK GENMASK(7, 0) #define REG14_TOL_MASK GENMASK(7, 4) #define REG14_RP_CODE_MASK GENMASK(3, 1) #define REG14_TG_CODE_HIGH_MASK GENMASK(0, 0) #define REG21_SEL_TX_CK_INV BIT(7) #define REG21_PMS_S_MASK GENMASK(3, 0) /* * REG33 does not match the ref manual. According to Sandor Yu from NXP, * "There is a doc issue on the i.MX8MP latest RM" * REG33 is being used per guidance from Sandor */ #define REG33_MODE_SET_DONE BIT(7) #define REG33_FIX_DA BIT(1) #define REG34_PHY_READY BIT(7) #define REG34_PLL_LOCK BIT(6) #define REG34_PHY_CLK_READY BIT(5) #ifndef MHZ #define MHZ (1000UL * 1000UL) #endif #define PHY_PLL_DIV_REGS_NUM 7 struct phy_config { u32 pixclk; u8 pll_div_regs[PHY_PLL_DIV_REGS_NUM]; }; /* * The calculated_phy_pll_cfg only handles integer divider for PMS, * meaning the last four entries will be fixed, but the first three will * be calculated by the PMS calculator. */ static struct phy_config calculated_phy_pll_cfg = { .pixclk = 0, .pll_div_regs = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x80, 0x00 }, }; /* The lookup table contains values for which the fractional divder is used */ static const struct phy_config phy_pll_cfg[] = { { .pixclk = 22250000, .pll_div_regs = { 0xd1, 0x4b, 0xf1, 0x89, 0x88, 0x80, 0x40 }, }, { .pixclk = 23750000, .pll_div_regs = { 0xd1, 0x50, 0xf1, 0x86, 0x85, 0x80, 0x40 }, }, { .pixclk = 24024000, .pll_div_regs = { 0xd1, 0x50, 0xf1, 0x99, 0x02, 0x80, 0x40 }, }, { .pixclk = 25175000, .pll_div_regs = { 0xd1, 0x54, 0xfc, 0xcc, 0x91, 0x80, 0x40 }, }, { .pixclk = 26750000, .pll_div_regs = { 0xd1, 0x5a, 0xf2, 0x89, 0x88, 0x80, 0x40 }, }, { .pixclk = 27027000, .pll_div_regs = { 0xd1, 0x5a, 0xf2, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 29500000, .pll_div_regs = { 0xd1, 0x62, 0xf4, 0x95, 0x08, 0x80, 0x40 }, }, { .pixclk = 30750000, .pll_div_regs = { 0xd1, 0x66, 0xf4, 0x82, 0x01, 0x88, 0x45 }, }, { .pixclk = 30888000, .pll_div_regs = { 0xd1, 0x66, 0xf4, 0x99, 0x18, 0x88, 0x45 }, }, { .pixclk = 33750000, .pll_div_regs = { 0xd1, 0x70, 0xf4, 0x82, 0x01, 0x80, 0x40 }, }, { .pixclk = 35000000, .pll_div_regs = { 0xd1, 0x58, 0xb8, 0x8b, 0x88, 0x80, 0x40 }, }, { .pixclk = 36036000, .pll_div_regs = { 0xd1, 0x5a, 0xb2, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 43243200, .pll_div_regs = { 0xd1, 0x5a, 0x92, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 44500000, .pll_div_regs = { 0xd1, 0x5c, 0x92, 0x98, 0x11, 0x84, 0x41 }, }, { .pixclk = 47000000, .pll_div_regs = { 0xd1, 0x62, 0x94, 0x95, 0x82, 0x80, 0x40 }, }, { .pixclk = 47500000, .pll_div_regs = { 0xd1, 0x63, 0x96, 0xa1, 0x82, 0x80, 0x40 }, }, { .pixclk = 50349650, .pll_div_regs = { 0xd1, 0x54, 0x7c, 0xc3, 0x8f, 0x80, 0x40 }, }, { .pixclk = 53250000, .pll_div_regs = { 0xd1, 0x58, 0x72, 0x84, 0x03, 0x82, 0x41 }, }, { .pixclk = 53500000, .pll_div_regs = { 0xd1, 0x5a, 0x72, 0x89, 0x88, 0x80, 0x40 }, }, { .pixclk = 54054000, .pll_div_regs = { 0xd1, 0x5a, 0x72, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 59000000, .pll_div_regs = { 0xd1, 0x62, 0x74, 0x95, 0x08, 0x80, 0x40 }, }, { .pixclk = 59340659, .pll_div_regs = { 0xd1, 0x62, 0x74, 0xdb, 0x52, 0x88, 0x47 }, }, { .pixclk = 61500000, .pll_div_regs = { 0xd1, 0x66, 0x74, 0x82, 0x01, 0x88, 0x45 }, }, { .pixclk = 63500000, .pll_div_regs = { 0xd1, 0x69, 0x74, 0x89, 0x08, 0x80, 0x40 }, }, { .pixclk = 67500000, .pll_div_regs = { 0xd1, 0x54, 0x52, 0x87, 0x03, 0x80, 0x40 }, }, { .pixclk = 70000000, .pll_div_regs = { 0xd1, 0x58, 0x58, 0x8b, 0x88, 0x80, 0x40 }, }, { .pixclk = 72072000, .pll_div_regs = { 0xd1, 0x5a, 0x52, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 74176000, .pll_div_regs = { 0xd1, 0x5d, 0x58, 0xdb, 0xA2, 0x88, 0x41 }, }, { .pixclk = 74250000, .pll_div_regs = { 0xd1, 0x5c, 0x52, 0x90, 0x0d, 0x84, 0x41 }, }, { .pixclk = 78500000, .pll_div_regs = { 0xd1, 0x62, 0x54, 0x87, 0x01, 0x80, 0x40 }, }, { .pixclk = 82000000, .pll_div_regs = { 0xd1, 0x66, 0x54, 0x82, 0x01, 0x88, 0x45 }, }, { .pixclk = 82500000, .pll_div_regs = { 0xd1, 0x67, 0x54, 0x88, 0x01, 0x90, 0x49 }, }, { .pixclk = 89000000, .pll_div_regs = { 0xd1, 0x70, 0x54, 0x84, 0x83, 0x80, 0x40 }, }, { .pixclk = 90000000, .pll_div_regs = { 0xd1, 0x70, 0x54, 0x82, 0x01, 0x80, 0x40 }, }, { .pixclk = 94000000, .pll_div_regs = { 0xd1, 0x4e, 0x32, 0xa7, 0x10, 0x80, 0x40 }, }, { .pixclk = 95000000, .pll_div_regs = { 0xd1, 0x50, 0x31, 0x86, 0x85, 0x80, 0x40 }, }, { .pixclk = 98901099, .pll_div_regs = { 0xd1, 0x52, 0x3a, 0xdb, 0x4c, 0x88, 0x47 }, }, { .pixclk = 99000000, .pll_div_regs = { 0xd1, 0x52, 0x32, 0x82, 0x01, 0x88, 0x47 }, }, { .pixclk = 100699300, .pll_div_regs = { 0xd1, 0x54, 0x3c, 0xc3, 0x8f, 0x80, 0x40 }, }, { .pixclk = 102500000, .pll_div_regs = { 0xd1, 0x55, 0x32, 0x8c, 0x05, 0x90, 0x4b }, }, { .pixclk = 104750000, .pll_div_regs = { 0xd1, 0x57, 0x32, 0x98, 0x07, 0x90, 0x49 }, }, { .pixclk = 106500000, .pll_div_regs = { 0xd1, 0x58, 0x32, 0x84, 0x03, 0x82, 0x41 }, }, { .pixclk = 107000000, .pll_div_regs = { 0xd1, 0x5a, 0x32, 0x89, 0x88, 0x80, 0x40 }, }, { .pixclk = 108108000, .pll_div_regs = { 0xd1, 0x5a, 0x32, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 118000000, .pll_div_regs = { 0xd1, 0x62, 0x34, 0x95, 0x08, 0x80, 0x40 }, }, { .pixclk = 123000000, .pll_div_regs = { 0xd1, 0x66, 0x34, 0x82, 0x01, 0x88, 0x45 }, }, { .pixclk = 127000000, .pll_div_regs = { 0xd1, 0x69, 0x34, 0x89, 0x08, 0x80, 0x40 }, }, { .pixclk = 135000000, .pll_div_regs = { 0xd1, 0x70, 0x34, 0x82, 0x01, 0x80, 0x40 }, }, { .pixclk = 135580000, .pll_div_regs = { 0xd1, 0x71, 0x39, 0xe9, 0x82, 0x9c, 0x5b }, }, { .pixclk = 137520000, .pll_div_regs = { 0xd1, 0x72, 0x38, 0x99, 0x10, 0x85, 0x41 }, }, { .pixclk = 138750000, .pll_div_regs = { 0xd1, 0x73, 0x35, 0x88, 0x05, 0x90, 0x4d }, }, { .pixclk = 140000000, .pll_div_regs = { 0xd1, 0x75, 0x36, 0xa7, 0x90, 0x80, 0x40 }, }, { .pixclk = 148352000, .pll_div_regs = { 0xd1, 0x7b, 0x35, 0xdb, 0x39, 0x90, 0x45 }, }, { .pixclk = 148500000, .pll_div_regs = { 0xd1, 0x7b, 0x35, 0x84, 0x03, 0x90, 0x45 }, }, { .pixclk = 154000000, .pll_div_regs = { 0xd1, 0x40, 0x18, 0x83, 0x01, 0x00, 0x40 }, }, { .pixclk = 157000000, .pll_div_regs = { 0xd1, 0x41, 0x11, 0xa7, 0x14, 0x80, 0x40 }, }, { .pixclk = 160000000, .pll_div_regs = { 0xd1, 0x42, 0x12, 0xa1, 0x20, 0x80, 0x40 }, }, { .pixclk = 162000000, .pll_div_regs = { 0xd1, 0x43, 0x18, 0x8b, 0x08, 0x96, 0x55 }, }, { .pixclk = 164000000, .pll_div_regs = { 0xd1, 0x45, 0x11, 0x83, 0x82, 0x90, 0x4b }, }, { .pixclk = 165000000, .pll_div_regs = { 0xd1, 0x45, 0x11, 0x84, 0x81, 0x90, 0x4b }, }, { .pixclk = 185625000, .pll_div_regs = { 0xd1, 0x4e, 0x12, 0x9a, 0x95, 0x80, 0x40 }, }, { .pixclk = 188000000, .pll_div_regs = { 0xd1, 0x4e, 0x12, 0xa7, 0x10, 0x80, 0x40 }, }, { .pixclk = 198000000, .pll_div_regs = { 0xd1, 0x52, 0x12, 0x82, 0x01, 0x88, 0x47 }, }, { .pixclk = 205000000, .pll_div_regs = { 0xd1, 0x55, 0x12, 0x8c, 0x05, 0x90, 0x4b }, }, { .pixclk = 209500000, .pll_div_regs = { 0xd1, 0x57, 0x12, 0x98, 0x07, 0x90, 0x49 }, }, { .pixclk = 213000000, .pll_div_regs = { 0xd1, 0x58, 0x12, 0x84, 0x03, 0x82, 0x41 }, }, { .pixclk = 216216000, .pll_div_regs = { 0xd1, 0x5a, 0x12, 0xfd, 0x0c, 0x80, 0x40 }, }, { .pixclk = 254000000, .pll_div_regs = { 0xd1, 0x69, 0x14, 0x89, 0x08, 0x80, 0x40 }, }, { .pixclk = 277500000, .pll_div_regs = { 0xd1, 0x73, 0x15, 0x88, 0x05, 0x90, 0x4d }, }, { .pixclk = 297000000, .pll_div_regs = { 0xd1, 0x7b, 0x15, 0x84, 0x03, 0x90, 0x45 }, }, }; struct reg_settings { u8 reg; u8 val; }; static const struct reg_settings common_phy_cfg[] = { { PHY_REG(0), 0x00 }, /* PHY_REG(1-7) pix clk specific */ { PHY_REG(8), 0x4f }, { PHY_REG(9), 0x30 }, { PHY_REG(10), 0x33 }, { PHY_REG(11), 0x65 }, /* REG12 pixclk specific */ /* REG13 pixclk specific */ /* REG14 pixclk specific */ { PHY_REG(15), 0x80 }, { PHY_REG(16), 0x6c }, { PHY_REG(17), 0xf2 }, { PHY_REG(18), 0x67 }, { PHY_REG(19), 0x00 }, { PHY_REG(20), 0x10 }, /* REG21 pixclk specific */ { PHY_REG(22), 0x30 }, { PHY_REG(23), 0x32 }, { PHY_REG(24), 0x60 }, { PHY_REG(25), 0x8f }, { PHY_REG(26), 0x00 }, { PHY_REG(27), 0x00 }, { PHY_REG(28), 0x08 }, { PHY_REG(29), 0x00 }, { PHY_REG(30), 0x00 }, { PHY_REG(31), 0x00 }, { PHY_REG(32), 0x00 }, { PHY_REG(33), 0x80 }, { PHY_REG(34), 0x00 }, { PHY_REG(35), 0x00 }, { PHY_REG(36), 0x00 }, { PHY_REG(37), 0x00 }, { PHY_REG(38), 0x00 }, { PHY_REG(39), 0x00 }, { PHY_REG(40), 0x00 }, { PHY_REG(41), 0xe0 }, { PHY_REG(42), 0x83 }, { PHY_REG(43), 0x0f }, { PHY_REG(44), 0x3E }, { PHY_REG(45), 0xf8 }, { PHY_REG(46), 0x00 }, { PHY_REG(47), 0x00 } }; struct fsl_samsung_hdmi_phy { struct device *dev; void __iomem *regs; struct clk *apbclk; struct clk *refclk; /* clk provider */ struct clk_hw hw; const struct phy_config *cur_cfg; }; static inline struct fsl_samsung_hdmi_phy * to_fsl_samsung_hdmi_phy(struct clk_hw *hw) { return container_of(hw, struct fsl_samsung_hdmi_phy, hw); } static void fsl_samsung_hdmi_phy_configure_pll_lock_det(struct fsl_samsung_hdmi_phy *phy, const struct phy_config *cfg) { u32 pclk = cfg->pixclk; u32 fld_tg_code; u32 pclk_khz; u8 div = 1; switch (cfg->pixclk) { case 22250000 ... 47500000: div = 1; break; case 50349650 ... 99000000: div = 2; break; case 100699300 ... 198000000: div = 4; break; case 205000000 ... 297000000: div = 8; break; } writeb(FIELD_PREP(REG12_CK_DIV_MASK, ilog2(div)), phy->regs + PHY_REG(12)); /* * Calculation for the frequency lock detector target code (fld_tg_code) * is based on reference manual register description of PHY_REG13 * (13.10.3.1.14.2): * 1st) Calculate int_pllclk which is determinded by FLD_CK_DIV * 2nd) Increase resolution to avoid rounding issues * 3th) Do the div (256 / Freq. of int_pllclk) * 24 * 4th) Reduce the resolution and always round up since the NXP * settings rounding up always too. TODO: Check if that is * correct. */ pclk /= div; pclk_khz = pclk / 1000; fld_tg_code = 256 * 1000 * 1000 / pclk_khz * 24; fld_tg_code = DIV_ROUND_UP(fld_tg_code, 1000); /* FLD_TOL and FLD_RP_CODE taken from downstream driver */ writeb(FIELD_PREP(REG13_TG_CODE_LOW_MASK, fld_tg_code), phy->regs + PHY_REG(13)); writeb(FIELD_PREP(REG14_TOL_MASK, 2) | FIELD_PREP(REG14_RP_CODE_MASK, 2) | FIELD_PREP(REG14_TG_CODE_HIGH_MASK, fld_tg_code >> 8), phy->regs + PHY_REG(14)); } static unsigned long fsl_samsung_hdmi_phy_find_pms(unsigned long fout, u8 *p, u16 *m, u8 *s) { unsigned long best_freq = 0; u32 min_delta = 0xffffffff; u8 _p, best_p; u16 _m, best_m; u8 _s, best_s; /* * Figure 13-78 of the reference manual states the PLL should be TMDS x 5 * while the TMDS_CLKO should be the PLL / 5. So to calculate the PLL, * take the pix clock x 5, then return the value of the PLL / 5. */ fout *= 5; /* The ref manual states the values of 'P' range from 1 to 11 */ for (_p = 1; _p <= 11; ++_p) { for (_s = 1; _s <= 16; ++_s) { u64 tmp; u32 delta; /* s must be one or even */ if (_s > 1 && (_s & 0x01) == 1) _s++; /* _s cannot be 14 per the TRM */ if (_s == 14) continue; /* * TODO: Ref Manual doesn't state the range of _m * so this should be further refined if possible. * This range was set based on the original values * in the lookup table */ tmp = (u64)fout * (_p * _s); do_div(tmp, 24 * MHZ); _m = tmp; if (_m < 0x30 || _m > 0x7b) continue; /* * Rev 2 of the Ref Manual states the * VCO can range between 750MHz and * 3GHz. The VCO is assumed to be * Fvco = (M * f_ref) / P, * where f_ref is 24MHz. */ tmp = div64_ul((u64)_m * 24 * MHZ, _p); if (tmp < 750 * MHZ || tmp > 3000 * MHZ) continue; /* Final frequency after post-divider */ do_div(tmp, _s); delta = abs(fout - tmp); if (delta < min_delta) { best_p = _p; best_s = _s; best_m = _m; min_delta = delta; best_freq = tmp; } } } if (best_freq) { *p = best_p; *m = best_m; *s = best_s; } return best_freq / 5; } static int fsl_samsung_hdmi_phy_configure(struct fsl_samsung_hdmi_phy *phy, const struct phy_config *cfg) { int i, ret; u8 val; /* HDMI PHY init */ writeb(REG33_FIX_DA, phy->regs + PHY_REG(33)); /* common PHY registers */ for (i = 0; i < ARRAY_SIZE(common_phy_cfg); i++) writeb(common_phy_cfg[i].val, phy->regs + common_phy_cfg[i].reg); /* set individual PLL registers PHY_REG1 ... PHY_REG7 */ for (i = 0; i < PHY_PLL_DIV_REGS_NUM; i++) writeb(cfg->pll_div_regs[i], phy->regs + PHY_REG(1) + i * 4); /* High nibble of PHY_REG3 and low nibble of PHY_REG21 both contain 'S' */ writeb(REG21_SEL_TX_CK_INV | FIELD_PREP(REG21_PMS_S_MASK, cfg->pll_div_regs[2] >> 4), phy->regs + PHY_REG(21)); fsl_samsung_hdmi_phy_configure_pll_lock_det(phy, cfg); writeb(REG33_FIX_DA | REG33_MODE_SET_DONE, phy->regs + PHY_REG(33)); ret = readb_poll_timeout(phy->regs + PHY_REG(34), val, val & REG34_PLL_LOCK, 50, 20000); if (ret) dev_err(phy->dev, "PLL failed to lock\n"); return ret; } static unsigned long phy_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) { struct fsl_samsung_hdmi_phy *phy = to_fsl_samsung_hdmi_phy(hw); if (!phy->cur_cfg) return 74250000; return phy->cur_cfg->pixclk; } /* Helper function to lookup the available fractional-divider rate */ static const struct phy_config *fsl_samsung_hdmi_phy_lookup_rate(unsigned long rate) { int i; /* Search the lookup table */ for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--) if (phy_pll_cfg[i].pixclk <= rate) break; return &phy_pll_cfg[i]; } static void fsl_samsung_hdmi_calculate_phy(struct phy_config *cal_phy, unsigned long rate, u8 p, u16 m, u8 s) { cal_phy->pixclk = rate; cal_phy->pll_div_regs[0] = FIELD_PREP(REG01_PMS_P_MASK, p); cal_phy->pll_div_regs[1] = m; cal_phy->pll_div_regs[2] = FIELD_PREP(REG03_PMS_S_MASK, s-1); /* pll_div_regs 3-6 are fixed and pre-defined already */ } static u32 fsl_samsung_hdmi_phy_get_closest_rate(unsigned long rate, u32 int_div_clk, u32 frac_div_clk) { /* Calculate the absolute value of the differences and return whichever is closest */ if (abs((long)rate - (long)int_div_clk) < abs((long)(rate - (long)frac_div_clk))) return int_div_clk; return frac_div_clk; } static long phy_clk_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate) { const struct phy_config *fract_div_phy; u32 int_div_clk; u16 m; u8 p, s; /* If the clock is out of range return error instead of searching */ if (rate > 297000000 || rate < 22250000) return -EINVAL; /* Search the fractional divider lookup table */ fract_div_phy = fsl_samsung_hdmi_phy_lookup_rate(rate); /* If the rate is an exact match, return that value */ if (rate == fract_div_phy->pixclk) return fract_div_phy->pixclk; /* If the exact match isn't found, calculate the integer divider */ int_div_clk = fsl_samsung_hdmi_phy_find_pms(rate, &p, &m, &s); /* If the int_div_clk rate is an exact match, return that value */ if (int_div_clk == rate) return int_div_clk; /* If neither rate is an exact match, use the value from the LUT */ return fract_div_phy->pixclk; } static int phy_use_fract_div(struct fsl_samsung_hdmi_phy *phy, const struct phy_config *fract_div_phy) { phy->cur_cfg = fract_div_phy; dev_dbg(phy->dev, "fsl_samsung_hdmi_phy: using fractional divider rate = %u\n", phy->cur_cfg->pixclk); return fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg); } static int phy_use_integer_div(struct fsl_samsung_hdmi_phy *phy, const struct phy_config *int_div_clk) { phy->cur_cfg = &calculated_phy_pll_cfg; dev_dbg(phy->dev, "fsl_samsung_hdmi_phy: integer divider rate = %u\n", phy->cur_cfg->pixclk); return fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg); } static int phy_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) { struct fsl_samsung_hdmi_phy *phy = to_fsl_samsung_hdmi_phy(hw); const struct phy_config *fract_div_phy; u32 int_div_clk; u16 m; u8 p, s; /* Search the fractional divider lookup table */ fract_div_phy = fsl_samsung_hdmi_phy_lookup_rate(rate); /* If the rate is an exact match, use that value */ if (fract_div_phy->pixclk == rate) return phy_use_fract_div(phy, fract_div_phy); /* * If the rate from the fractional divider is not exact, check the integer divider, * and use it if that value is an exact match. */ int_div_clk = fsl_samsung_hdmi_phy_find_pms(rate, &p, &m, &s); fsl_samsung_hdmi_calculate_phy(&calculated_phy_pll_cfg, int_div_clk, p, m, s); if (int_div_clk == rate) return phy_use_integer_div(phy, &calculated_phy_pll_cfg); /* * Compare the difference between the integer clock and the fractional clock against * the desired clock and which whichever is closest. */ if (fsl_samsung_hdmi_phy_get_closest_rate(rate, int_div_clk, fract_div_phy->pixclk) == fract_div_phy->pixclk) return phy_use_fract_div(phy, fract_div_phy); else return phy_use_integer_div(phy, &calculated_phy_pll_cfg); } static const struct clk_ops phy_clk_ops = { .recalc_rate = phy_clk_recalc_rate, .round_rate = phy_clk_round_rate, .set_rate = phy_clk_set_rate, }; static int phy_clk_register(struct fsl_samsung_hdmi_phy *phy) { struct device *dev = phy->dev; struct device_node *np = dev->of_node; struct clk_init_data init; const char *parent_name; struct clk *phyclk; int ret; parent_name = __clk_get_name(phy->refclk); init.parent_names = &parent_name; init.num_parents = 1; init.flags = 0; init.name = "hdmi_pclk"; init.ops = &phy_clk_ops; phy->hw.init = &init; phyclk = devm_clk_register(dev, &phy->hw); if (IS_ERR(phyclk)) return dev_err_probe(dev, PTR_ERR(phyclk), "failed to register clock\n"); ret = of_clk_add_hw_provider(np, of_clk_hw_simple_get, phyclk); if (ret) return dev_err_probe(dev, ret, "failed to register clock provider\n"); return 0; } static int fsl_samsung_hdmi_phy_probe(struct platform_device *pdev) { struct fsl_samsung_hdmi_phy *phy; int ret; phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL); if (!phy) return -ENOMEM; platform_set_drvdata(pdev, phy); phy->dev = &pdev->dev; phy->regs = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(phy->regs)) return PTR_ERR(phy->regs); phy->apbclk = devm_clk_get(phy->dev, "apb"); if (IS_ERR(phy->apbclk)) return dev_err_probe(phy->dev, PTR_ERR(phy->apbclk), "failed to get apb clk\n"); phy->refclk = devm_clk_get(phy->dev, "ref"); if (IS_ERR(phy->refclk)) return dev_err_probe(phy->dev, PTR_ERR(phy->refclk), "failed to get ref clk\n"); ret = clk_prepare_enable(phy->apbclk); if (ret) { dev_err(phy->dev, "failed to enable apbclk\n"); return ret; } pm_runtime_get_noresume(phy->dev); pm_runtime_set_active(phy->dev); pm_runtime_enable(phy->dev); ret = phy_clk_register(phy); if (ret) { dev_err(&pdev->dev, "register clk failed\n"); goto register_clk_failed; } pm_runtime_put(phy->dev); return 0; register_clk_failed: clk_disable_unprepare(phy->apbclk); return ret; } static void fsl_samsung_hdmi_phy_remove(struct platform_device *pdev) { of_clk_del_provider(pdev->dev.of_node); } static int __maybe_unused fsl_samsung_hdmi_phy_suspend(struct device *dev) { struct fsl_samsung_hdmi_phy *phy = dev_get_drvdata(dev); clk_disable_unprepare(phy->apbclk); return 0; } static int __maybe_unused fsl_samsung_hdmi_phy_resume(struct device *dev) { struct fsl_samsung_hdmi_phy *phy = dev_get_drvdata(dev); int ret = 0; ret = clk_prepare_enable(phy->apbclk); if (ret) { dev_err(phy->dev, "failed to enable apbclk\n"); return ret; } if (phy->cur_cfg) ret = fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg); return ret; } static DEFINE_RUNTIME_DEV_PM_OPS(fsl_samsung_hdmi_phy_pm_ops, fsl_samsung_hdmi_phy_suspend, fsl_samsung_hdmi_phy_resume, NULL); static const struct of_device_id fsl_samsung_hdmi_phy_of_match[] = { { .compatible = "fsl,imx8mp-hdmi-phy", }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, fsl_samsung_hdmi_phy_of_match); static struct platform_driver fsl_samsung_hdmi_phy_driver = { .probe = fsl_samsung_hdmi_phy_probe, .remove = fsl_samsung_hdmi_phy_remove, .driver = { .name = "fsl-samsung-hdmi-phy", .of_match_table = fsl_samsung_hdmi_phy_of_match, .pm = pm_ptr(&fsl_samsung_hdmi_phy_pm_ops), }, }; module_platform_driver(fsl_samsung_hdmi_phy_driver); MODULE_AUTHOR("Sandor Yu "); MODULE_DESCRIPTION("SAMSUNG HDMI 2.0 Transmitter PHY Driver"); MODULE_LICENSE("GPL");