/* * This file is part of the Chelsio T4 PCI-E SR-IOV Virtual Function Ethernet * driver for Linux. * * Copyright (c) 2009-2010 Chelsio Communications, Inc. All rights reserved. * * This software is available to you under a choice of one of two * licenses. You may choose to be licensed under the terms of the GNU * General Public License (GPL) Version 2, available from the file * COPYING in the main directory of this source tree, or the * OpenIB.org BSD license below: * * Redistribution and use in source and binary forms, with or * without modification, are permitted provided that the following * conditions are met: * * - Redistributions of source code must retain the above * copyright notice, this list of conditions and the following * disclaimer. * * - Redistributions in binary form must reproduce the above * copyright notice, this list of conditions and the following * disclaimer in the documentation and/or other materials * provided with the distribution. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE * SOFTWARE. */ #include #include #include #include #include #include #include #include #include #include "t4vf_common.h" #include "t4vf_defs.h" #include "../cxgb4/t4_regs.h" #include "../cxgb4/t4_values.h" #include "../cxgb4/t4fw_api.h" #include "../cxgb4/t4_msg.h" /* * Constants ... */ enum { /* * Egress Queue sizes, producer and consumer indices are all in units * of Egress Context Units bytes. Note that as far as the hardware is * concerned, the free list is an Egress Queue (the host produces free * buffers which the hardware consumes) and free list entries are * 64-bit PCI DMA addresses. */ EQ_UNIT = SGE_EQ_IDXSIZE, FL_PER_EQ_UNIT = EQ_UNIT / sizeof(__be64), TXD_PER_EQ_UNIT = EQ_UNIT / sizeof(__be64), /* * Max number of TX descriptors we clean up at a time. Should be * modest as freeing skbs isn't cheap and it happens while holding * locks. We just need to free packets faster than they arrive, we * eventually catch up and keep the amortized cost reasonable. */ MAX_TX_RECLAIM = 16, /* * Max number of Rx buffers we replenish at a time. Again keep this * modest, allocating buffers isn't cheap either. */ MAX_RX_REFILL = 16, /* * Period of the Rx queue check timer. This timer is infrequent as it * has something to do only when the system experiences severe memory * shortage. */ RX_QCHECK_PERIOD = (HZ / 2), /* * Period of the TX queue check timer and the maximum number of TX * descriptors to be reclaimed by the TX timer. */ TX_QCHECK_PERIOD = (HZ / 2), MAX_TIMER_TX_RECLAIM = 100, /* * Suspend an Ethernet TX queue with fewer available descriptors than * this. We always want to have room for a maximum sized packet: * inline immediate data + MAX_SKB_FRAGS. This is the same as * calc_tx_flits() for a TSO packet with nr_frags == MAX_SKB_FRAGS * (see that function and its helpers for a description of the * calculation). */ ETHTXQ_MAX_FRAGS = MAX_SKB_FRAGS + 1, ETHTXQ_MAX_SGL_LEN = ((3 * (ETHTXQ_MAX_FRAGS-1))/2 + ((ETHTXQ_MAX_FRAGS-1) & 1) + 2), ETHTXQ_MAX_HDR = (sizeof(struct fw_eth_tx_pkt_vm_wr) + sizeof(struct cpl_tx_pkt_lso_core) + sizeof(struct cpl_tx_pkt_core)) / sizeof(__be64), ETHTXQ_MAX_FLITS = ETHTXQ_MAX_SGL_LEN + ETHTXQ_MAX_HDR, ETHTXQ_STOP_THRES = 1 + DIV_ROUND_UP(ETHTXQ_MAX_FLITS, TXD_PER_EQ_UNIT), /* * Max TX descriptor space we allow for an Ethernet packet to be * inlined into a WR. This is limited by the maximum value which * we can specify for immediate data in the firmware Ethernet TX * Work Request. */ MAX_IMM_TX_PKT_LEN = FW_WR_IMMDLEN_M, /* * Max size of a WR sent through a control TX queue. */ MAX_CTRL_WR_LEN = 256, /* * Maximum amount of data which we'll ever need to inline into a * TX ring: max(MAX_IMM_TX_PKT_LEN, MAX_CTRL_WR_LEN). */ MAX_IMM_TX_LEN = (MAX_IMM_TX_PKT_LEN > MAX_CTRL_WR_LEN ? MAX_IMM_TX_PKT_LEN : MAX_CTRL_WR_LEN), /* * For incoming packets less than RX_COPY_THRES, we copy the data into * an skb rather than referencing the data. We allocate enough * in-line room in skb's to accommodate pulling in RX_PULL_LEN bytes * of the data (header). */ RX_COPY_THRES = 256, RX_PULL_LEN = 128, /* * Main body length for sk_buffs used for RX Ethernet packets with * fragments. Should be >= RX_PULL_LEN but possibly bigger to give * pskb_may_pull() some room. */ RX_SKB_LEN = 512, }; /* * Software state per TX descriptor. */ struct tx_sw_desc { struct sk_buff *skb; /* socket buffer of TX data source */ struct ulptx_sgl *sgl; /* scatter/gather list in TX Queue */ }; /* * Software state per RX Free List descriptor. We keep track of the allocated * FL page, its size, and its PCI DMA address (if the page is mapped). The FL * page size and its PCI DMA mapped state are stored in the low bits of the * PCI DMA address as per below. */ struct rx_sw_desc { struct page *page; /* Free List page buffer */ dma_addr_t dma_addr; /* PCI DMA address (if mapped) */ /* and flags (see below) */ }; /* * The low bits of rx_sw_desc.dma_addr have special meaning. Note that the * SGE also uses the low 4 bits to determine the size of the buffer. It uses * those bits to index into the SGE_FL_BUFFER_SIZE[index] register array. * Since we only use SGE_FL_BUFFER_SIZE0 and SGE_FL_BUFFER_SIZE1, these low 4 * bits can only contain a 0 or a 1 to indicate which size buffer we're giving * to the SGE. Thus, our software state of "is the buffer mapped for DMA" is * maintained in an inverse sense so the hardware never sees that bit high. */ enum { RX_LARGE_BUF = 1 << 0, /* buffer is SGE_FL_BUFFER_SIZE[1] */ RX_UNMAPPED_BUF = 1 << 1, /* buffer is not mapped */ }; /** * get_buf_addr - return DMA buffer address of software descriptor * @sdesc: pointer to the software buffer descriptor * * Return the DMA buffer address of a software descriptor (stripping out * our low-order flag bits). */ static inline dma_addr_t get_buf_addr(const struct rx_sw_desc *sdesc) { return sdesc->dma_addr & ~(dma_addr_t)(RX_LARGE_BUF | RX_UNMAPPED_BUF); } /** * is_buf_mapped - is buffer mapped for DMA? * @sdesc: pointer to the software buffer descriptor * * Determine whether the buffer associated with a software descriptor in * mapped for DMA or not. */ static inline bool is_buf_mapped(const struct rx_sw_desc *sdesc) { return !(sdesc->dma_addr & RX_UNMAPPED_BUF); } /** * need_skb_unmap - does the platform need unmapping of sk_buffs? * * Returns true if the platform needs sk_buff unmapping. The compiler * optimizes away unnecessary code if this returns true. */ static inline int need_skb_unmap(void) { #ifdef CONFIG_NEED_DMA_MAP_STATE return 1; #else return 0; #endif } /** * txq_avail - return the number of available slots in a TX queue * @tq: the TX queue * * Returns the number of available descriptors in a TX queue. */ static inline unsigned int txq_avail(const struct sge_txq *tq) { return tq->size - 1 - tq->in_use; } /** * fl_cap - return the capacity of a Free List * @fl: the Free List * * Returns the capacity of a Free List. The capacity is less than the * size because an Egress Queue Index Unit worth of descriptors needs to * be left unpopulated, otherwise the Producer and Consumer indices PIDX * and CIDX will match and the hardware will think the FL is empty. */ static inline unsigned int fl_cap(const struct sge_fl *fl) { return fl->size - FL_PER_EQ_UNIT; } /** * fl_starving - return whether a Free List is starving. * @adapter: pointer to the adapter * @fl: the Free List * * Tests specified Free List to see whether the number of buffers * available to the hardware has falled below our "starvation" * threshold. */ static inline bool fl_starving(const struct adapter *adapter, const struct sge_fl *fl) { const struct sge *s = &adapter->sge; return fl->avail - fl->pend_cred <= s->fl_starve_thres; } /** * map_skb - map an skb for DMA to the device * @dev: the egress net device * @skb: the packet to map * @addr: a pointer to the base of the DMA mapping array * * Map an skb for DMA to the device and return an array of DMA addresses. */ static int map_skb(struct device *dev, const struct sk_buff *skb, dma_addr_t *addr) { const skb_frag_t *fp, *end; const struct skb_shared_info *si; *addr = dma_map_single(dev, skb->data, skb_headlen(skb), DMA_TO_DEVICE); if (dma_mapping_error(dev, *addr)) goto out_err; si = skb_shinfo(skb); end = &si->frags[si->nr_frags]; for (fp = si->frags; fp < end; fp++) { *++addr = skb_frag_dma_map(dev, fp, 0, skb_frag_size(fp), DMA_TO_DEVICE); if (dma_mapping_error(dev, *addr)) goto unwind; } return 0; unwind: while (fp-- > si->frags) dma_unmap_page(dev, *--addr, skb_frag_size(fp), DMA_TO_DEVICE); dma_unmap_single(dev, addr[-1], skb_headlen(skb), DMA_TO_DEVICE); out_err: return -ENOMEM; } static void unmap_sgl(struct device *dev, const struct sk_buff *skb, const struct ulptx_sgl *sgl, const struct sge_txq *tq) { const struct ulptx_sge_pair *p; unsigned int nfrags = skb_shinfo(skb)->nr_frags; if (likely(skb_headlen(skb))) dma_unmap_single(dev, be64_to_cpu(sgl->addr0), be32_to_cpu(sgl->len0), DMA_TO_DEVICE); else { dma_unmap_page(dev, be64_to_cpu(sgl->addr0), be32_to_cpu(sgl->len0), DMA_TO_DEVICE); nfrags--; } /* * the complexity below is because of the possibility of a wrap-around * in the middle of an SGL */ for (p = sgl->sge; nfrags >= 2; nfrags -= 2) { if (likely((u8 *)(p + 1) <= (u8 *)tq->stat)) { unmap: dma_unmap_page(dev, be64_to_cpu(p->addr[0]), be32_to_cpu(p->len[0]), DMA_TO_DEVICE); dma_unmap_page(dev, be64_to_cpu(p->addr[1]), be32_to_cpu(p->len[1]), DMA_TO_DEVICE); p++; } else if ((u8 *)p == (u8 *)tq->stat) { p = (const struct ulptx_sge_pair *)tq->desc; goto unmap; } else if ((u8 *)p + 8 == (u8 *)tq->stat) { const __be64 *addr = (const __be64 *)tq->desc; dma_unmap_page(dev, be64_to_cpu(addr[0]), be32_to_cpu(p->len[0]), DMA_TO_DEVICE); dma_unmap_page(dev, be64_to_cpu(addr[1]), be32_to_cpu(p->len[1]), DMA_TO_DEVICE); p = (const struct ulptx_sge_pair *)&addr[2]; } else { const __be64 *addr = (const __be64 *)tq->desc; dma_unmap_page(dev, be64_to_cpu(p->addr[0]), be32_to_cpu(p->len[0]), DMA_TO_DEVICE); dma_unmap_page(dev, be64_to_cpu(addr[0]), be32_to_cpu(p->len[1]), DMA_TO_DEVICE); p = (const struct ulptx_sge_pair *)&addr[1]; } } if (nfrags) { __be64 addr; if ((u8 *)p == (u8 *)tq->stat) p = (const struct ulptx_sge_pair *)tq->desc; addr = ((u8 *)p + 16 <= (u8 *)tq->stat ? p->addr[0] : *(const __be64 *)tq->desc); dma_unmap_page(dev, be64_to_cpu(addr), be32_to_cpu(p->len[0]), DMA_TO_DEVICE); } } /** * free_tx_desc - reclaims TX descriptors and their buffers * @adapter: the adapter * @tq: the TX queue to reclaim descriptors from * @n: the number of descriptors to reclaim * @unmap: whether the buffers should be unmapped for DMA * * Reclaims TX descriptors from an SGE TX queue and frees the associated * TX buffers. Called with the TX queue lock held. */ static void free_tx_desc(struct adapter *adapter, struct sge_txq *tq, unsigned int n, bool unmap) { struct tx_sw_desc *sdesc; unsigned int cidx = tq->cidx; struct device *dev = adapter->pdev_dev; const int need_unmap = need_skb_unmap() && unmap; sdesc = &tq->sdesc[cidx]; while (n--) { /* * If we kept a reference to the original TX skb, we need to * unmap it from PCI DMA space (if required) and free it. */ if (sdesc->skb) { if (need_unmap) unmap_sgl(dev, sdesc->skb, sdesc->sgl, tq); dev_consume_skb_any(sdesc->skb); sdesc->skb = NULL; } sdesc++; if (++cidx == tq->size) { cidx = 0; sdesc = tq->sdesc; } } tq->cidx = cidx; } /* * Return the number of reclaimable descriptors in a TX queue. */ static inline int reclaimable(const struct sge_txq *tq) { int hw_cidx = be16_to_cpu(tq->stat->cidx); int reclaimable = hw_cidx - tq->cidx; if (reclaimable < 0) reclaimable += tq->size; return reclaimable; } /** * reclaim_completed_tx - reclaims completed TX descriptors * @adapter: the adapter * @tq: the TX queue to reclaim completed descriptors from * @unmap: whether the buffers should be unmapped for DMA * * Reclaims TX descriptors that the SGE has indicated it has processed, * and frees the associated buffers if possible. Called with the TX * queue locked. */ static inline void reclaim_completed_tx(struct adapter *adapter, struct sge_txq *tq, bool unmap) { int avail = reclaimable(tq); if (avail) { /* * Limit the amount of clean up work we do at a time to keep * the TX lock hold time O(1). */ if (avail > MAX_TX_RECLAIM) avail = MAX_TX_RECLAIM; free_tx_desc(adapter, tq, avail, unmap); tq->in_use -= avail; } } /** * get_buf_size - return the size of an RX Free List buffer. * @adapter: pointer to the associated adapter * @sdesc: pointer to the software buffer descriptor */ static inline int get_buf_size(const struct adapter *adapter, const struct rx_sw_desc *sdesc) { const struct sge *s = &adapter->sge; return (s->fl_pg_order > 0 && (sdesc->dma_addr & RX_LARGE_BUF) ? (PAGE_SIZE << s->fl_pg_order) : PAGE_SIZE); } /** * free_rx_bufs - free RX buffers on an SGE Free List * @adapter: the adapter * @fl: the SGE Free List to free buffers from * @n: how many buffers to free * * Release the next @n buffers on an SGE Free List RX queue. The * buffers must be made inaccessible to hardware before calling this * function. */ static void free_rx_bufs(struct adapter *adapter, struct sge_fl *fl, int n) { while (n--) { struct rx_sw_desc *sdesc = &fl->sdesc[fl->cidx]; if (is_buf_mapped(sdesc)) dma_unmap_page(adapter->pdev_dev, get_buf_addr(sdesc), get_buf_size(adapter, sdesc), PCI_DMA_FROMDEVICE); put_page(sdesc->page); sdesc->page = NULL; if (++fl->cidx == fl->size) fl->cidx = 0; fl->avail--; } } /** * unmap_rx_buf - unmap the current RX buffer on an SGE Free List * @adapter: the adapter * @fl: the SGE Free List * * Unmap the current buffer on an SGE Free List RX queue. The * buffer must be made inaccessible to HW before calling this function. * * This is similar to @free_rx_bufs above but does not free the buffer. * Do note that the FL still loses any further access to the buffer. * This is used predominantly to "transfer ownership" of an FL buffer * to another entity (typically an skb's fragment list). */ static void unmap_rx_buf(struct adapter *adapter, struct sge_fl *fl) { struct rx_sw_desc *sdesc = &fl->sdesc[fl->cidx]; if (is_buf_mapped(sdesc)) dma_unmap_page(adapter->pdev_dev, get_buf_addr(sdesc), get_buf_size(adapter, sdesc), PCI_DMA_FROMDEVICE); sdesc->page = NULL; if (++fl->cidx == fl->size) fl->cidx = 0; fl->avail--; } /** * ring_fl_db - righ doorbell on free list * @adapter: the adapter * @fl: the Free List whose doorbell should be rung ... * * Tell the Scatter Gather Engine that there are new free list entries * available. */ static inline void ring_fl_db(struct adapter *adapter, struct sge_fl *fl) { u32 val; /* The SGE keeps track of its Producer and Consumer Indices in terms * of Egress Queue Units so we can only tell it about integral numbers * of multiples of Free List Entries per Egress Queue Units ... */ if (fl->pend_cred >= FL_PER_EQ_UNIT) { if (is_t4(adapter->params.chip)) val = PIDX_V(fl->pend_cred / FL_PER_EQ_UNIT); else val = PIDX_T5_V(fl->pend_cred / FL_PER_EQ_UNIT) | DBTYPE_F; val |= DBPRIO_F; /* Make sure all memory writes to the Free List queue are * committed before we tell the hardware about them. */ wmb(); /* If we don't have access to the new User Doorbell (T5+), use * the old doorbell mechanism; otherwise use the new BAR2 * mechanism. */ if (unlikely(fl->bar2_addr == NULL)) { t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL, QID_V(fl->cntxt_id) | val); } else { writel(val | QID_V(fl->bar2_qid), fl->bar2_addr + SGE_UDB_KDOORBELL); /* This Write memory Barrier will force the write to * the User Doorbell area to be flushed. */ wmb(); } fl->pend_cred %= FL_PER_EQ_UNIT; } } /** * set_rx_sw_desc - initialize software RX buffer descriptor * @sdesc: pointer to the softwore RX buffer descriptor * @page: pointer to the page data structure backing the RX buffer * @dma_addr: PCI DMA address (possibly with low-bit flags) */ static inline void set_rx_sw_desc(struct rx_sw_desc *sdesc, struct page *page, dma_addr_t dma_addr) { sdesc->page = page; sdesc->dma_addr = dma_addr; } /* * Support for poisoning RX buffers ... */ #define POISON_BUF_VAL -1 static inline void poison_buf(struct page *page, size_t sz) { #if POISON_BUF_VAL >= 0 memset(page_address(page), POISON_BUF_VAL, sz); #endif } /** * refill_fl - refill an SGE RX buffer ring * @adapter: the adapter * @fl: the Free List ring to refill * @n: the number of new buffers to allocate * @gfp: the gfp flags for the allocations * * (Re)populate an SGE free-buffer queue with up to @n new packet buffers, * allocated with the supplied gfp flags. The caller must assure that * @n does not exceed the queue's capacity -- i.e. (cidx == pidx) _IN * EGRESS QUEUE UNITS_ indicates an empty Free List! Returns the number * of buffers allocated. If afterwards the queue is found critically low, * mark it as starving in the bitmap of starving FLs. */ static unsigned int refill_fl(struct adapter *adapter, struct sge_fl *fl, int n, gfp_t gfp) { struct sge *s = &adapter->sge; struct page *page; dma_addr_t dma_addr; unsigned int cred = fl->avail; __be64 *d = &fl->desc[fl->pidx]; struct rx_sw_desc *sdesc = &fl->sdesc[fl->pidx]; /* * Sanity: ensure that the result of adding n Free List buffers * won't result in wrapping the SGE's Producer Index around to * it's Consumer Index thereby indicating an empty Free List ... */ BUG_ON(fl->avail + n > fl->size - FL_PER_EQ_UNIT); gfp |= __GFP_NOWARN; /* * If we support large pages, prefer large buffers and fail over to * small pages if we can't allocate large pages to satisfy the refill. * If we don't support large pages, drop directly into the small page * allocation code. */ if (s->fl_pg_order == 0) goto alloc_small_pages; while (n) { page = __dev_alloc_pages(gfp, s->fl_pg_order); if (unlikely(!page)) { /* * We've failed inour attempt to allocate a "large * page". Fail over to the "small page" allocation * below. */ fl->large_alloc_failed++; break; } poison_buf(page, PAGE_SIZE << s->fl_pg_order); dma_addr = dma_map_page(adapter->pdev_dev, page, 0, PAGE_SIZE << s->fl_pg_order, PCI_DMA_FROMDEVICE); if (unlikely(dma_mapping_error(adapter->pdev_dev, dma_addr))) { /* * We've run out of DMA mapping space. Free up the * buffer and return with what we've managed to put * into the free list. We don't want to fail over to * the small page allocation below in this case * because DMA mapping resources are typically * critical resources once they become scarse. */ __free_pages(page, s->fl_pg_order); goto out; } dma_addr |= RX_LARGE_BUF; *d++ = cpu_to_be64(dma_addr); set_rx_sw_desc(sdesc, page, dma_addr); sdesc++; fl->avail++; if (++fl->pidx == fl->size) { fl->pidx = 0; sdesc = fl->sdesc; d = fl->desc; } n--; } alloc_small_pages: while (n--) { page = __dev_alloc_page(gfp); if (unlikely(!page)) { fl->alloc_failed++; break; } poison_buf(page, PAGE_SIZE); dma_addr = dma_map_page(adapter->pdev_dev, page, 0, PAGE_SIZE, PCI_DMA_FROMDEVICE); if (unlikely(dma_mapping_error(adapter->pdev_dev, dma_addr))) { put_page(page); break; } *d++ = cpu_to_be64(dma_addr); set_rx_sw_desc(sdesc, page, dma_addr); sdesc++; fl->avail++; if (++fl->pidx == fl->size) { fl->pidx = 0; sdesc = fl->sdesc; d = fl->desc; } } out: /* * Update our accounting state to incorporate the new Free List * buffers, tell the hardware about them and return the number of * buffers which we were able to allocate. */ cred = fl->avail - cred; fl->pend_cred += cred; ring_fl_db(adapter, fl); if (unlikely(fl_starving(adapter, fl))) { smp_wmb(); set_bit(fl->cntxt_id, adapter->sge.starving_fl); } return cred; } /* * Refill a Free List to its capacity or the Maximum Refill Increment, * whichever is smaller ... */ static inline void __refill_fl(struct adapter *adapter, struct sge_fl *fl) { refill_fl(adapter, fl, min((unsigned int)MAX_RX_REFILL, fl_cap(fl) - fl->avail), GFP_ATOMIC); } /** * alloc_ring - allocate resources for an SGE descriptor ring * @dev: the PCI device's core device * @nelem: the number of descriptors * @hwsize: the size of each hardware descriptor * @swsize: the size of each software descriptor * @busaddrp: the physical PCI bus address of the allocated ring * @swringp: return address pointer for software ring * @stat_size: extra space in hardware ring for status information * * Allocates resources for an SGE descriptor ring, such as TX queues, * free buffer lists, response queues, etc. Each SGE ring requires * space for its hardware descriptors plus, optionally, space for software * state associated with each hardware entry (the metadata). The function * returns three values: the virtual address for the hardware ring (the * return value of the function), the PCI bus address of the hardware * ring (in *busaddrp), and the address of the software ring (in swringp). * Both the hardware and software rings are returned zeroed out. */ static void *alloc_ring(struct device *dev, size_t nelem, size_t hwsize, size_t swsize, dma_addr_t *busaddrp, void *swringp, size_t stat_size) { /* * Allocate the hardware ring and PCI DMA bus address space for said. */ size_t hwlen = nelem * hwsize + stat_size; void *hwring = dma_alloc_coherent(dev, hwlen, busaddrp, GFP_KERNEL); if (!hwring) return NULL; /* * If the caller wants a software ring, allocate it and return a * pointer to it in *swringp. */ BUG_ON((swsize != 0) != (swringp != NULL)); if (swsize) { void *swring = kcalloc(nelem, swsize, GFP_KERNEL); if (!swring) { dma_free_coherent(dev, hwlen, hwring, *busaddrp); return NULL; } *(void **)swringp = swring; } /* * Zero out the hardware ring and return its address as our function * value. */ memset(hwring, 0, hwlen); return hwring; } /** * sgl_len - calculates the size of an SGL of the given capacity * @n: the number of SGL entries * * Calculates the number of flits (8-byte units) needed for a Direct * Scatter/Gather List that can hold the given number of entries. */ static inline unsigned int sgl_len(unsigned int n) { /* * A Direct Scatter Gather List uses 32-bit lengths and 64-bit PCI DMA * addresses. The DSGL Work Request starts off with a 32-bit DSGL * ULPTX header, then Length0, then Address0, then, for 1 <= i <= N, * repeated sequences of { Length[i], Length[i+1], Address[i], * Address[i+1] } (this ensures that all addresses are on 64-bit * boundaries). If N is even, then Length[N+1] should be set to 0 and * Address[N+1] is omitted. * * The following calculation incorporates all of the above. It's * somewhat hard to follow but, briefly: the "+2" accounts for the * first two flits which include the DSGL header, Length0 and * Address0; the "(3*(n-1))/2" covers the main body of list entries (3 * flits for every pair of the remaining N) +1 if (n-1) is odd; and * finally the "+((n-1)&1)" adds the one remaining flit needed if * (n-1) is odd ... */ n--; return (3 * n) / 2 + (n & 1) + 2; } /** * flits_to_desc - returns the num of TX descriptors for the given flits * @flits: the number of flits * * Returns the number of TX descriptors needed for the supplied number * of flits. */ static inline unsigned int flits_to_desc(unsigned int flits) { BUG_ON(flits > SGE_MAX_WR_LEN / sizeof(__be64)); return DIV_ROUND_UP(flits, TXD_PER_EQ_UNIT); } /** * is_eth_imm - can an Ethernet packet be sent as immediate data? * @skb: the packet * * Returns whether an Ethernet packet is small enough to fit completely as * immediate data. */ static inline int is_eth_imm(const struct sk_buff *skb) { /* * The VF Driver uses the FW_ETH_TX_PKT_VM_WR firmware Work Request * which does not accommodate immediate data. We could dike out all * of the support code for immediate data but that would tie our hands * too much if we ever want to enhace the firmware. It would also * create more differences between the PF and VF Drivers. */ return false; } /** * calc_tx_flits - calculate the number of flits for a packet TX WR * @skb: the packet * * Returns the number of flits needed for a TX Work Request for the * given Ethernet packet, including the needed WR and CPL headers. */ static inline unsigned int calc_tx_flits(const struct sk_buff *skb) { unsigned int flits; /* * If the skb is small enough, we can pump it out as a work request * with only immediate data. In that case we just have to have the * TX Packet header plus the skb data in the Work Request. */ if (is_eth_imm(skb)) return DIV_ROUND_UP(skb->len + sizeof(struct cpl_tx_pkt), sizeof(__be64)); /* * Otherwise, we're going to have to construct a Scatter gather list * of the skb body and fragments. We also include the flits necessary * for the TX Packet Work Request and CPL. We always have a firmware * Write Header (incorporated as part of the cpl_tx_pkt_lso and * cpl_tx_pkt structures), followed by either a TX Packet Write CPL * message or, if we're doing a Large Send Offload, an LSO CPL message * with an embeded TX Packet Write CPL message. */ flits = sgl_len(skb_shinfo(skb)->nr_frags + 1); if (skb_shinfo(skb)->gso_size) flits += (sizeof(struct fw_eth_tx_pkt_vm_wr) + sizeof(struct cpl_tx_pkt_lso_core) + sizeof(struct cpl_tx_pkt_core)) / sizeof(__be64); else flits += (sizeof(struct fw_eth_tx_pkt_vm_wr) + sizeof(struct cpl_tx_pkt_core)) / sizeof(__be64); return flits; } /** * write_sgl - populate a Scatter/Gather List for a packet * @skb: the packet * @tq: the TX queue we are writing into * @sgl: starting location for writing the SGL * @end: points right after the end of the SGL * @start: start offset into skb main-body data to include in the SGL * @addr: the list of DMA bus addresses for the SGL elements * * Generates a Scatter/Gather List for the buffers that make up a packet. * The caller must provide adequate space for the SGL that will be written. * The SGL includes all of the packet's page fragments and the data in its * main body except for the first @start bytes. @pos must be 16-byte * aligned and within a TX descriptor with available space. @end points * write after the end of the SGL but does not account for any potential * wrap around, i.e., @end > @tq->stat. */ static void write_sgl(const struct sk_buff *skb, struct sge_txq *tq, struct ulptx_sgl *sgl, u64 *end, unsigned int start, const dma_addr_t *addr) { unsigned int i, len; struct ulptx_sge_pair *to; const struct skb_shared_info *si = skb_shinfo(skb); unsigned int nfrags = si->nr_frags; struct ulptx_sge_pair buf[MAX_SKB_FRAGS / 2 + 1]; len = skb_headlen(skb) - start; if (likely(len)) { sgl->len0 = htonl(len); sgl->addr0 = cpu_to_be64(addr[0] + start); nfrags++; } else { sgl->len0 = htonl(skb_frag_size(&si->frags[0])); sgl->addr0 = cpu_to_be64(addr[1]); } sgl->cmd_nsge = htonl(ULPTX_CMD_V(ULP_TX_SC_DSGL) | ULPTX_NSGE_V(nfrags)); if (likely(--nfrags == 0)) return; /* * Most of the complexity below deals with the possibility we hit the * end of the queue in the middle of writing the SGL. For this case * only we create the SGL in a temporary buffer and then copy it. */ to = (u8 *)end > (u8 *)tq->stat ? buf : sgl->sge; for (i = (nfrags != si->nr_frags); nfrags >= 2; nfrags -= 2, to++) { to->len[0] = cpu_to_be32(skb_frag_size(&si->frags[i])); to->len[1] = cpu_to_be32(skb_frag_size(&si->frags[++i])); to->addr[0] = cpu_to_be64(addr[i]); to->addr[1] = cpu_to_be64(addr[++i]); } if (nfrags) { to->len[0] = cpu_to_be32(skb_frag_size(&si->frags[i])); to->len[1] = cpu_to_be32(0); to->addr[0] = cpu_to_be64(addr[i + 1]); } if (unlikely((u8 *)end > (u8 *)tq->stat)) { unsigned int part0 = (u8 *)tq->stat - (u8 *)sgl->sge, part1; if (likely(part0)) memcpy(sgl->sge, buf, part0); part1 = (u8 *)end - (u8 *)tq->stat; memcpy(tq->desc, (u8 *)buf + part0, part1); end = (void *)tq->desc + part1; } if ((uintptr_t)end & 8) /* 0-pad to multiple of 16 */ *end = 0; } /** * check_ring_tx_db - check and potentially ring a TX queue's doorbell * @adapter: the adapter * @tq: the TX queue * @n: number of new descriptors to give to HW * * Ring the doorbel for a TX queue. */ static inline void ring_tx_db(struct adapter *adapter, struct sge_txq *tq, int n) { /* Make sure that all writes to the TX Descriptors are committed * before we tell the hardware about them. */ wmb(); /* If we don't have access to the new User Doorbell (T5+), use the old * doorbell mechanism; otherwise use the new BAR2 mechanism. */ if (unlikely(tq->bar2_addr == NULL)) { u32 val = PIDX_V(n); t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_KDOORBELL, QID_V(tq->cntxt_id) | val); } else { u32 val = PIDX_T5_V(n); /* T4 and later chips share the same PIDX field offset within * the doorbell, but T5 and later shrank the field in order to * gain a bit for Doorbell Priority. The field was absurdly * large in the first place (14 bits) so we just use the T5 * and later limits and warn if a Queue ID is too large. */ WARN_ON(val & DBPRIO_F); /* If we're only writing a single Egress Unit and the BAR2 * Queue ID is 0, we can use the Write Combining Doorbell * Gather Buffer; otherwise we use the simple doorbell. */ if (n == 1 && tq->bar2_qid == 0) { unsigned int index = (tq->pidx ? (tq->pidx - 1) : (tq->size - 1)); __be64 *src = (__be64 *)&tq->desc[index]; __be64 __iomem *dst = (__be64 __iomem *)(tq->bar2_addr + SGE_UDB_WCDOORBELL); unsigned int count = EQ_UNIT / sizeof(__be64); /* Copy the TX Descriptor in a tight loop in order to * try to get it to the adapter in a single Write * Combined transfer on the PCI-E Bus. If the Write * Combine fails (say because of an interrupt, etc.) * the hardware will simply take the last write as a * simple doorbell write with a PIDX Increment of 1 * and will fetch the TX Descriptor from memory via * DMA. */ while (count) { /* the (__force u64) is because the compiler * doesn't understand the endian swizzling * going on */ writeq((__force u64)*src, dst); src++; dst++; count--; } } else writel(val | QID_V(tq->bar2_qid), tq->bar2_addr + SGE_UDB_KDOORBELL); /* This Write Memory Barrier will force the write to the User * Doorbell area to be flushed. This is needed to prevent * writes on different CPUs for the same queue from hitting * the adapter out of order. This is required when some Work * Requests take the Write Combine Gather Buffer path (user * doorbell area offset [SGE_UDB_WCDOORBELL..+63]) and some * take the traditional path where we simply increment the * PIDX (User Doorbell area SGE_UDB_KDOORBELL) and have the * hardware DMA read the actual Work Request. */ wmb(); } } /** * inline_tx_skb - inline a packet's data into TX descriptors * @skb: the packet * @tq: the TX queue where the packet will be inlined * @pos: starting position in the TX queue to inline the packet * * Inline a packet's contents directly into TX descriptors, starting at * the given position within the TX DMA ring. * Most of the complexity of this operation is dealing with wrap arounds * in the middle of the packet we want to inline. */ static void inline_tx_skb(const struct sk_buff *skb, const struct sge_txq *tq, void *pos) { u64 *p; int left = (void *)tq->stat - pos; if (likely(skb->len <= left)) { if (likely(!skb->data_len)) skb_copy_from_linear_data(skb, pos, skb->len); else skb_copy_bits(skb, 0, pos, skb->len); pos += skb->len; } else { skb_copy_bits(skb, 0, pos, left); skb_copy_bits(skb, left, tq->desc, skb->len - left); pos = (void *)tq->desc + (skb->len - left); } /* 0-pad to multiple of 16 */ p = PTR_ALIGN(pos, 8); if ((uintptr_t)p & 8) *p = 0; } /* * Figure out what HW csum a packet wants and return the appropriate control * bits. */ static u64 hwcsum(const struct sk_buff *skb) { int csum_type; const struct iphdr *iph = ip_hdr(skb); if (iph->version == 4) { if (iph->protocol == IPPROTO_TCP) csum_type = TX_CSUM_TCPIP; else if (iph->protocol == IPPROTO_UDP) csum_type = TX_CSUM_UDPIP; else { nocsum: /* * unknown protocol, disable HW csum * and hope a bad packet is detected */ return TXPKT_L4CSUM_DIS; } } else { /* * this doesn't work with extension headers */ const struct ipv6hdr *ip6h = (const struct ipv6hdr *)iph; if (ip6h->nexthdr == IPPROTO_TCP) csum_type = TX_CSUM_TCPIP6; else if (ip6h->nexthdr == IPPROTO_UDP) csum_type = TX_CSUM_UDPIP6; else goto nocsum; } if (likely(csum_type >= TX_CSUM_TCPIP)) return TXPKT_CSUM_TYPE(csum_type) | TXPKT_IPHDR_LEN(skb_network_header_len(skb)) | TXPKT_ETHHDR_LEN(skb_network_offset(skb) - ETH_HLEN); else { int start = skb_transport_offset(skb); return TXPKT_CSUM_TYPE(csum_type) | TXPKT_CSUM_START(start) | TXPKT_CSUM_LOC(start + skb->csum_offset); } } /* * Stop an Ethernet TX queue and record that state change. */ static void txq_stop(struct sge_eth_txq *txq) { netif_tx_stop_queue(txq->txq); txq->q.stops++; } /* * Advance our software state for a TX queue by adding n in use descriptors. */ static inline void txq_advance(struct sge_txq *tq, unsigned int n) { tq->in_use += n; tq->pidx += n; if (tq->pidx >= tq->size) tq->pidx -= tq->size; } /** * t4vf_eth_xmit - add a packet to an Ethernet TX queue * @skb: the packet * @dev: the egress net device * * Add a packet to an SGE Ethernet TX queue. Runs with softirqs disabled. */ int t4vf_eth_xmit(struct sk_buff *skb, struct net_device *dev) { u32 wr_mid; u64 cntrl, *end; int qidx, credits; unsigned int flits, ndesc; struct adapter *adapter; struct sge_eth_txq *txq; const struct port_info *pi; struct fw_eth_tx_pkt_vm_wr *wr; struct cpl_tx_pkt_core *cpl; const struct skb_shared_info *ssi; dma_addr_t addr[MAX_SKB_FRAGS + 1]; const size_t fw_hdr_copy_len = (sizeof(wr->ethmacdst) + sizeof(wr->ethmacsrc) + sizeof(wr->ethtype) + sizeof(wr->vlantci)); /* * The chip minimum packet length is 10 octets but the firmware * command that we are using requires that we copy the Ethernet header * (including the VLAN tag) into the header so we reject anything * smaller than that ... */ if (unlikely(skb->len < fw_hdr_copy_len)) goto out_free; /* * Figure out which TX Queue we're going to use. */ pi = netdev_priv(dev); adapter = pi->adapter; qidx = skb_get_queue_mapping(skb); BUG_ON(qidx >= pi->nqsets); txq = &adapter->sge.ethtxq[pi->first_qset + qidx]; /* * Take this opportunity to reclaim any TX Descriptors whose DMA * transfers have completed. */ reclaim_completed_tx(adapter, &txq->q, true); /* * Calculate the number of flits and TX Descriptors we're going to * need along with how many TX Descriptors will be left over after * we inject our Work Request. */ flits = calc_tx_flits(skb); ndesc = flits_to_desc(flits); credits = txq_avail(&txq->q) - ndesc; if (unlikely(credits < 0)) { /* * Not enough room for this packet's Work Request. Stop the * TX Queue and return a "busy" condition. The queue will get * started later on when the firmware informs us that space * has opened up. */ txq_stop(txq); dev_err(adapter->pdev_dev, "%s: TX ring %u full while queue awake!\n", dev->name, qidx); return NETDEV_TX_BUSY; } if (!is_eth_imm(skb) && unlikely(map_skb(adapter->pdev_dev, skb, addr) < 0)) { /* * We need to map the skb into PCI DMA space (because it can't * be in-lined directly into the Work Request) and the mapping * operation failed. Record the error and drop the packet. */ txq->mapping_err++; goto out_free; } wr_mid = FW_WR_LEN16_V(DIV_ROUND_UP(flits, 2)); if (unlikely(credits < ETHTXQ_STOP_THRES)) { /* * After we're done injecting the Work Request for this * packet, we'll be below our "stop threshold" so stop the TX * Queue now and schedule a request for an SGE Egress Queue * Update message. The queue will get started later on when * the firmware processes this Work Request and sends us an * Egress Queue Status Update message indicating that space * has opened up. */ txq_stop(txq); wr_mid |= FW_WR_EQUEQ_F | FW_WR_EQUIQ_F; } /* * Start filling in our Work Request. Note that we do _not_ handle * the WR Header wrapping around the TX Descriptor Ring. If our * maximum header size ever exceeds one TX Descriptor, we'll need to * do something else here. */ BUG_ON(DIV_ROUND_UP(ETHTXQ_MAX_HDR, TXD_PER_EQ_UNIT) > 1); wr = (void *)&txq->q.desc[txq->q.pidx]; wr->equiq_to_len16 = cpu_to_be32(wr_mid); wr->r3[0] = cpu_to_be32(0); wr->r3[1] = cpu_to_be32(0); skb_copy_from_linear_data(skb, (void *)wr->ethmacdst, fw_hdr_copy_len); end = (u64 *)wr + flits; /* * If this is a Large Send Offload packet we'll put in an LSO CPL * message with an encapsulated TX Packet CPL message. Otherwise we * just use a TX Packet CPL message. */ ssi = skb_shinfo(skb); if (ssi->gso_size) { struct cpl_tx_pkt_lso_core *lso = (void *)(wr + 1); bool v6 = (ssi->gso_type & SKB_GSO_TCPV6) != 0; int l3hdr_len = skb_network_header_len(skb); int eth_xtra_len = skb_network_offset(skb) - ETH_HLEN; wr->op_immdlen = cpu_to_be32(FW_WR_OP_V(FW_ETH_TX_PKT_VM_WR) | FW_WR_IMMDLEN_V(sizeof(*lso) + sizeof(*cpl))); /* * Fill in the LSO CPL message. */ lso->lso_ctrl = cpu_to_be32(LSO_OPCODE(CPL_TX_PKT_LSO) | LSO_FIRST_SLICE | LSO_LAST_SLICE | LSO_IPV6(v6) | LSO_ETHHDR_LEN(eth_xtra_len/4) | LSO_IPHDR_LEN(l3hdr_len/4) | LSO_TCPHDR_LEN(tcp_hdr(skb)->doff)); lso->ipid_ofst = cpu_to_be16(0); lso->mss = cpu_to_be16(ssi->gso_size); lso->seqno_offset = cpu_to_be32(0); if (is_t4(adapter->params.chip)) lso->len = cpu_to_be32(skb->len); else lso->len = cpu_to_be32(LSO_T5_XFER_SIZE(skb->len)); /* * Set up TX Packet CPL pointer, control word and perform * accounting. */ cpl = (void *)(lso + 1); cntrl = (TXPKT_CSUM_TYPE(v6 ? TX_CSUM_TCPIP6 : TX_CSUM_TCPIP) | TXPKT_IPHDR_LEN(l3hdr_len) | TXPKT_ETHHDR_LEN(eth_xtra_len)); txq->tso++; txq->tx_cso += ssi->gso_segs; } else { int len; len = is_eth_imm(skb) ? skb->len + sizeof(*cpl) : sizeof(*cpl); wr->op_immdlen = cpu_to_be32(FW_WR_OP_V(FW_ETH_TX_PKT_VM_WR) | FW_WR_IMMDLEN_V(len)); /* * Set up TX Packet CPL pointer, control word and perform * accounting. */ cpl = (void *)(wr + 1); if (skb->ip_summed == CHECKSUM_PARTIAL) { cntrl = hwcsum(skb) | TXPKT_IPCSUM_DIS; txq->tx_cso++; } else cntrl = TXPKT_L4CSUM_DIS | TXPKT_IPCSUM_DIS; } /* * If there's a VLAN tag present, add that to the list of things to * do in this Work Request. */ if (skb_vlan_tag_present(skb)) { txq->vlan_ins++; cntrl |= TXPKT_VLAN_VLD | TXPKT_VLAN(skb_vlan_tag_get(skb)); } /* * Fill in the TX Packet CPL message header. */ cpl->ctrl0 = cpu_to_be32(TXPKT_OPCODE(CPL_TX_PKT_XT) | TXPKT_INTF(pi->port_id) | TXPKT_PF(0)); cpl->pack = cpu_to_be16(0); cpl->len = cpu_to_be16(skb->len); cpl->ctrl1 = cpu_to_be64(cntrl); #ifdef T4_TRACE T4_TRACE5(adapter->tb[txq->q.cntxt_id & 7], "eth_xmit: ndesc %u, credits %u, pidx %u, len %u, frags %u", ndesc, credits, txq->q.pidx, skb->len, ssi->nr_frags); #endif /* * Fill in the body of the TX Packet CPL message with either in-lined * data or a Scatter/Gather List. */ if (is_eth_imm(skb)) { /* * In-line the packet's data and free the skb since we don't * need it any longer. */ inline_tx_skb(skb, &txq->q, cpl + 1); dev_consume_skb_any(skb); } else { /* * Write the skb's Scatter/Gather list into the TX Packet CPL * message and retain a pointer to the skb so we can free it * later when its DMA completes. (We store the skb pointer * in the Software Descriptor corresponding to the last TX * Descriptor used by the Work Request.) * * The retained skb will be freed when the corresponding TX * Descriptors are reclaimed after their DMAs complete. * However, this could take quite a while since, in general, * the hardware is set up to be lazy about sending DMA * completion notifications to us and we mostly perform TX * reclaims in the transmit routine. * * This is good for performamce but means that we rely on new * TX packets arriving to run the destructors of completed * packets, which open up space in their sockets' send queues. * Sometimes we do not get such new packets causing TX to * stall. A single UDP transmitter is a good example of this * situation. We have a clean up timer that periodically * reclaims completed packets but it doesn't run often enough * (nor do we want it to) to prevent lengthy stalls. A * solution to this problem is to run the destructor early, * after the packet is queued but before it's DMAd. A con is * that we lie to socket memory accounting, but the amount of * extra memory is reasonable (limited by the number of TX * descriptors), the packets do actually get freed quickly by * new packets almost always, and for protocols like TCP that * wait for acks to really free up the data the extra memory * is even less. On the positive side we run the destructors * on the sending CPU rather than on a potentially different * completing CPU, usually a good thing. * * Run the destructor before telling the DMA engine about the * packet to make sure it doesn't complete and get freed * prematurely. */ struct ulptx_sgl *sgl = (struct ulptx_sgl *)(cpl + 1); struct sge_txq *tq = &txq->q; int last_desc; /* * If the Work Request header was an exact multiple of our TX * Descriptor length, then it's possible that the starting SGL * pointer lines up exactly with the end of our TX Descriptor * ring. If that's the case, wrap around to the beginning * here ... */ if (unlikely((void *)sgl == (void *)tq->stat)) { sgl = (void *)tq->desc; end = ((void *)tq->desc + ((void *)end - (void *)tq->stat)); } write_sgl(skb, tq, sgl, end, 0, addr); skb_orphan(skb); last_desc = tq->pidx + ndesc - 1; if (last_desc >= tq->size) last_desc -= tq->size; tq->sdesc[last_desc].skb = skb; tq->sdesc[last_desc].sgl = sgl; } /* * Advance our internal TX Queue state, tell the hardware about * the new TX descriptors and return success. */ txq_advance(&txq->q, ndesc); dev->trans_start = jiffies; ring_tx_db(adapter, &txq->q, ndesc); return NETDEV_TX_OK; out_free: /* * An error of some sort happened. Free the TX skb and tell the * OS that we've "dealt" with the packet ... */ dev_kfree_skb_any(skb); return NETDEV_TX_OK; } /** * copy_frags - copy fragments from gather list into skb_shared_info * @skb: destination skb * @gl: source internal packet gather list * @offset: packet start offset in first page * * Copy an internal packet gather list into a Linux skb_shared_info * structure. */ static inline void copy_frags(struct sk_buff *skb, const struct pkt_gl *gl, unsigned int offset) { int i; /* usually there's just one frag */ __skb_fill_page_desc(skb, 0, gl->frags[0].page, gl->frags[0].offset + offset, gl->frags[0].size - offset); skb_shinfo(skb)->nr_frags = gl->nfrags; for (i = 1; i < gl->nfrags; i++) __skb_fill_page_desc(skb, i, gl->frags[i].page, gl->frags[i].offset, gl->frags[i].size); /* get a reference to the last page, we don't own it */ get_page(gl->frags[gl->nfrags - 1].page); } /** * t4vf_pktgl_to_skb - build an sk_buff from a packet gather list * @gl: the gather list * @skb_len: size of sk_buff main body if it carries fragments * @pull_len: amount of data to move to the sk_buff's main body * * Builds an sk_buff from the given packet gather list. Returns the * sk_buff or %NULL if sk_buff allocation failed. */ static struct sk_buff *t4vf_pktgl_to_skb(const struct pkt_gl *gl, unsigned int skb_len, unsigned int pull_len) { struct sk_buff *skb; /* * If the ingress packet is small enough, allocate an skb large enough * for all of the data and copy it inline. Otherwise, allocate an skb * with enough room to pull in the header and reference the rest of * the data via the skb fragment list. * * Below we rely on RX_COPY_THRES being less than the smallest Rx * buff! size, which is expected since buffers are at least * PAGE_SIZEd. In this case packets up to RX_COPY_THRES have only one * fragment. */ if (gl->tot_len <= RX_COPY_THRES) { /* small packets have only one fragment */ skb = alloc_skb(gl->tot_len, GFP_ATOMIC); if (unlikely(!skb)) goto out; __skb_put(skb, gl->tot_len); skb_copy_to_linear_data(skb, gl->va, gl->tot_len); } else { skb = alloc_skb(skb_len, GFP_ATOMIC); if (unlikely(!skb)) goto out; __skb_put(skb, pull_len); skb_copy_to_linear_data(skb, gl->va, pull_len); copy_frags(skb, gl, pull_len); skb->len = gl->tot_len; skb->data_len = skb->len - pull_len; skb->truesize += skb->data_len; } out: return skb; } /** * t4vf_pktgl_free - free a packet gather list * @gl: the gather list * * Releases the pages of a packet gather list. We do not own the last * page on the list and do not free it. */ static void t4vf_pktgl_free(const struct pkt_gl *gl) { int frag; frag = gl->nfrags - 1; while (frag--) put_page(gl->frags[frag].page); } /** * do_gro - perform Generic Receive Offload ingress packet processing * @rxq: ingress RX Ethernet Queue * @gl: gather list for ingress packet * @pkt: CPL header for last packet fragment * * Perform Generic Receive Offload (GRO) ingress packet processing. * We use the standard Linux GRO interfaces for this. */ static void do_gro(struct sge_eth_rxq *rxq, const struct pkt_gl *gl, const struct cpl_rx_pkt *pkt) { struct adapter *adapter = rxq->rspq.adapter; struct sge *s = &adapter->sge; int ret; struct sk_buff *skb; skb = napi_get_frags(&rxq->rspq.napi); if (unlikely(!skb)) { t4vf_pktgl_free(gl); rxq->stats.rx_drops++; return; } copy_frags(skb, gl, s->pktshift); skb->len = gl->tot_len - s->pktshift; skb->data_len = skb->len; skb->truesize += skb->data_len; skb->ip_summed = CHECKSUM_UNNECESSARY; skb_record_rx_queue(skb, rxq->rspq.idx); if (pkt->vlan_ex) { __vlan_hwaccel_put_tag(skb, cpu_to_be16(ETH_P_8021Q), be16_to_cpu(pkt->vlan)); rxq->stats.vlan_ex++; } ret = napi_gro_frags(&rxq->rspq.napi); if (ret == GRO_HELD) rxq->stats.lro_pkts++; else if (ret == GRO_MERGED || ret == GRO_MERGED_FREE) rxq->stats.lro_merged++; rxq->stats.pkts++; rxq->stats.rx_cso++; } /** * t4vf_ethrx_handler - process an ingress ethernet packet * @rspq: the response queue that received the packet * @rsp: the response queue descriptor holding the RX_PKT message * @gl: the gather list of packet fragments * * Process an ingress ethernet packet and deliver it to the stack. */ int t4vf_ethrx_handler(struct sge_rspq *rspq, const __be64 *rsp, const struct pkt_gl *gl) { struct sk_buff *skb; const struct cpl_rx_pkt *pkt = (void *)rsp; bool csum_ok = pkt->csum_calc && !pkt->err_vec && (rspq->netdev->features & NETIF_F_RXCSUM); struct sge_eth_rxq *rxq = container_of(rspq, struct sge_eth_rxq, rspq); struct adapter *adapter = rspq->adapter; struct sge *s = &adapter->sge; /* * If this is a good TCP packet and we have Generic Receive Offload * enabled, handle the packet in the GRO path. */ if ((pkt->l2info & cpu_to_be32(RXF_TCP_F)) && (rspq->netdev->features & NETIF_F_GRO) && csum_ok && !pkt->ip_frag) { do_gro(rxq, gl, pkt); return 0; } /* * Convert the Packet Gather List into an skb. */ skb = t4vf_pktgl_to_skb(gl, RX_SKB_LEN, RX_PULL_LEN); if (unlikely(!skb)) { t4vf_pktgl_free(gl); rxq->stats.rx_drops++; return 0; } __skb_pull(skb, s->pktshift); skb->protocol = eth_type_trans(skb, rspq->netdev); skb_record_rx_queue(skb, rspq->idx); rxq->stats.pkts++; if (csum_ok && !pkt->err_vec && (be32_to_cpu(pkt->l2info) & (RXF_UDP_F | RXF_TCP_F))) { if (!pkt->ip_frag) skb->ip_summed = CHECKSUM_UNNECESSARY; else { __sum16 c = (__force __sum16)pkt->csum; skb->csum = csum_unfold(c); skb->ip_summed = CHECKSUM_COMPLETE; } rxq->stats.rx_cso++; } else skb_checksum_none_assert(skb); if (pkt->vlan_ex) { rxq->stats.vlan_ex++; __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), be16_to_cpu(pkt->vlan)); } netif_receive_skb(skb); return 0; } /** * is_new_response - check if a response is newly written * @rc: the response control descriptor * @rspq: the response queue * * Returns true if a response descriptor contains a yet unprocessed * response. */ static inline bool is_new_response(const struct rsp_ctrl *rc, const struct sge_rspq *rspq) { return RSPD_GEN(rc->type_gen) == rspq->gen; } /** * restore_rx_bufs - put back a packet's RX buffers * @gl: the packet gather list * @fl: the SGE Free List * @nfrags: how many fragments in @si * * Called when we find out that the current packet, @si, can't be * processed right away for some reason. This is a very rare event and * there's no effort to make this suspension/resumption process * particularly efficient. * * We implement the suspension by putting all of the RX buffers associated * with the current packet back on the original Free List. The buffers * have already been unmapped and are left unmapped, we mark them as * unmapped in order to prevent further unmapping attempts. (Effectively * this function undoes the series of @unmap_rx_buf calls which were done * to create the current packet's gather list.) This leaves us ready to * restart processing of the packet the next time we start processing the * RX Queue ... */ static void restore_rx_bufs(const struct pkt_gl *gl, struct sge_fl *fl, int frags) { struct rx_sw_desc *sdesc; while (frags--) { if (fl->cidx == 0) fl->cidx = fl->size - 1; else fl->cidx--; sdesc = &fl->sdesc[fl->cidx]; sdesc->page = gl->frags[frags].page; sdesc->dma_addr |= RX_UNMAPPED_BUF; fl->avail++; } } /** * rspq_next - advance to the next entry in a response queue * @rspq: the queue * * Updates the state of a response queue to advance it to the next entry. */ static inline void rspq_next(struct sge_rspq *rspq) { rspq->cur_desc = (void *)rspq->cur_desc + rspq->iqe_len; if (unlikely(++rspq->cidx == rspq->size)) { rspq->cidx = 0; rspq->gen ^= 1; rspq->cur_desc = rspq->desc; } } /** * process_responses - process responses from an SGE response queue * @rspq: the ingress response queue to process * @budget: how many responses can be processed in this round * * Process responses from a Scatter Gather Engine response queue up to * the supplied budget. Responses include received packets as well as * control messages from firmware or hardware. * * Additionally choose the interrupt holdoff time for the next interrupt * on this queue. If the system is under memory shortage use a fairly * long delay to help recovery. */ static int process_responses(struct sge_rspq *rspq, int budget) { struct sge_eth_rxq *rxq = container_of(rspq, struct sge_eth_rxq, rspq); struct adapter *adapter = rspq->adapter; struct sge *s = &adapter->sge; int budget_left = budget; while (likely(budget_left)) { int ret, rsp_type; const struct rsp_ctrl *rc; rc = (void *)rspq->cur_desc + (rspq->iqe_len - sizeof(*rc)); if (!is_new_response(rc, rspq)) break; /* * Figure out what kind of response we've received from the * SGE. */ rmb(); rsp_type = RSPD_TYPE(rc->type_gen); if (likely(rsp_type == RSP_TYPE_FLBUF)) { struct page_frag *fp; struct pkt_gl gl; const struct rx_sw_desc *sdesc; u32 bufsz, frag; u32 len = be32_to_cpu(rc->pldbuflen_qid); /* * If we get a "new buffer" message from the SGE we * need to move on to the next Free List buffer. */ if (len & RSPD_NEWBUF) { /* * We get one "new buffer" message when we * first start up a queue so we need to ignore * it when our offset into the buffer is 0. */ if (likely(rspq->offset > 0)) { free_rx_bufs(rspq->adapter, &rxq->fl, 1); rspq->offset = 0; } len = RSPD_LEN(len); } gl.tot_len = len; /* * Gather packet fragments. */ for (frag = 0, fp = gl.frags; /**/; frag++, fp++) { BUG_ON(frag >= MAX_SKB_FRAGS); BUG_ON(rxq->fl.avail == 0); sdesc = &rxq->fl.sdesc[rxq->fl.cidx]; bufsz = get_buf_size(adapter, sdesc); fp->page = sdesc->page; fp->offset = rspq->offset; fp->size = min(bufsz, len); len -= fp->size; if (!len) break; unmap_rx_buf(rspq->adapter, &rxq->fl); } gl.nfrags = frag+1; /* * Last buffer remains mapped so explicitly make it * coherent for CPU access and start preloading first * cache line ... */ dma_sync_single_for_cpu(rspq->adapter->pdev_dev, get_buf_addr(sdesc), fp->size, DMA_FROM_DEVICE); gl.va = (page_address(gl.frags[0].page) + gl.frags[0].offset); prefetch(gl.va); /* * Hand the new ingress packet to the handler for * this Response Queue. */ ret = rspq->handler(rspq, rspq->cur_desc, &gl); if (likely(ret == 0)) rspq->offset += ALIGN(fp->size, s->fl_align); else restore_rx_bufs(&gl, &rxq->fl, frag); } else if (likely(rsp_type == RSP_TYPE_CPL)) { ret = rspq->handler(rspq, rspq->cur_desc, NULL); } else { WARN_ON(rsp_type > RSP_TYPE_CPL); ret = 0; } if (unlikely(ret)) { /* * Couldn't process descriptor, back off for recovery. * We use the SGE's last timer which has the longest * interrupt coalescing value ... */ const int NOMEM_TIMER_IDX = SGE_NTIMERS-1; rspq->next_intr_params = QINTR_TIMER_IDX(NOMEM_TIMER_IDX); break; } rspq_next(rspq); budget_left--; } /* * If this is a Response Queue with an associated Free List and * at least two Egress Queue units available in the Free List * for new buffer pointers, refill the Free List. */ if (rspq->offset >= 0 && rxq->fl.size - rxq->fl.avail >= 2*FL_PER_EQ_UNIT) __refill_fl(rspq->adapter, &rxq->fl); return budget - budget_left; } /** * napi_rx_handler - the NAPI handler for RX processing * @napi: the napi instance * @budget: how many packets we can process in this round * * Handler for new data events when using NAPI. This does not need any * locking or protection from interrupts as data interrupts are off at * this point and other adapter interrupts do not interfere (the latter * in not a concern at all with MSI-X as non-data interrupts then have * a separate handler). */ static int napi_rx_handler(struct napi_struct *napi, int budget) { unsigned int intr_params; struct sge_rspq *rspq = container_of(napi, struct sge_rspq, napi); int work_done = process_responses(rspq, budget); u32 val; if (likely(work_done < budget)) { napi_complete(napi); intr_params = rspq->next_intr_params; rspq->next_intr_params = rspq->intr_params; } else intr_params = QINTR_TIMER_IDX(SGE_TIMER_UPD_CIDX); if (unlikely(work_done == 0)) rspq->unhandled_irqs++; val = CIDXINC_V(work_done) | SEINTARM_V(intr_params); if (is_t4(rspq->adapter->params.chip)) { t4_write_reg(rspq->adapter, T4VF_SGE_BASE_ADDR + SGE_VF_GTS, val | INGRESSQID_V((u32)rspq->cntxt_id)); } else { writel(val | INGRESSQID_V(rspq->bar2_qid), rspq->bar2_addr + SGE_UDB_GTS); wmb(); } return work_done; } /* * The MSI-X interrupt handler for an SGE response queue for the NAPI case * (i.e., response queue serviced by NAPI polling). */ irqreturn_t t4vf_sge_intr_msix(int irq, void *cookie) { struct sge_rspq *rspq = cookie; napi_schedule(&rspq->napi); return IRQ_HANDLED; } /* * Process the indirect interrupt entries in the interrupt queue and kick off * NAPI for each queue that has generated an entry. */ static unsigned int process_intrq(struct adapter *adapter) { struct sge *s = &adapter->sge; struct sge_rspq *intrq = &s->intrq; unsigned int work_done; u32 val; spin_lock(&adapter->sge.intrq_lock); for (work_done = 0; ; work_done++) { const struct rsp_ctrl *rc; unsigned int qid, iq_idx; struct sge_rspq *rspq; /* * Grab the next response from the interrupt queue and bail * out if it's not a new response. */ rc = (void *)intrq->cur_desc + (intrq->iqe_len - sizeof(*rc)); if (!is_new_response(rc, intrq)) break; /* * If the response isn't a forwarded interrupt message issue a * error and go on to the next response message. This should * never happen ... */ rmb(); if (unlikely(RSPD_TYPE(rc->type_gen) != RSP_TYPE_INTR)) { dev_err(adapter->pdev_dev, "Unexpected INTRQ response type %d\n", RSPD_TYPE(rc->type_gen)); continue; } /* * Extract the Queue ID from the interrupt message and perform * sanity checking to make sure it really refers to one of our * Ingress Queues which is active and matches the queue's ID. * None of these error conditions should ever happen so we may * want to either make them fatal and/or conditionalized under * DEBUG. */ qid = RSPD_QID(be32_to_cpu(rc->pldbuflen_qid)); iq_idx = IQ_IDX(s, qid); if (unlikely(iq_idx >= MAX_INGQ)) { dev_err(adapter->pdev_dev, "Ingress QID %d out of range\n", qid); continue; } rspq = s->ingr_map[iq_idx]; if (unlikely(rspq == NULL)) { dev_err(adapter->pdev_dev, "Ingress QID %d RSPQ=NULL\n", qid); continue; } if (unlikely(rspq->abs_id != qid)) { dev_err(adapter->pdev_dev, "Ingress QID %d refers to RSPQ %d\n", qid, rspq->abs_id); continue; } /* * Schedule NAPI processing on the indicated Response Queue * and move on to the next entry in the Forwarded Interrupt * Queue. */ napi_schedule(&rspq->napi); rspq_next(intrq); } val = CIDXINC_V(work_done) | SEINTARM_V(intrq->intr_params); if (is_t4(adapter->params.chip)) t4_write_reg(adapter, T4VF_SGE_BASE_ADDR + SGE_VF_GTS, val | INGRESSQID_V(intrq->cntxt_id)); else { writel(val | INGRESSQID_V(intrq->bar2_qid), intrq->bar2_addr + SGE_UDB_GTS); wmb(); } spin_unlock(&adapter->sge.intrq_lock); return work_done; } /* * The MSI interrupt handler handles data events from SGE response queues as * well as error and other async events as they all use the same MSI vector. */ static irqreturn_t t4vf_intr_msi(int irq, void *cookie) { struct adapter *adapter = cookie; process_intrq(adapter); return IRQ_HANDLED; } /** * t4vf_intr_handler - select the top-level interrupt handler * @adapter: the adapter * * Selects the top-level interrupt handler based on the type of interrupts * (MSI-X or MSI). */ irq_handler_t t4vf_intr_handler(struct adapter *adapter) { BUG_ON((adapter->flags & (USING_MSIX|USING_MSI)) == 0); if (adapter->flags & USING_MSIX) return t4vf_sge_intr_msix; else return t4vf_intr_msi; } /** * sge_rx_timer_cb - perform periodic maintenance of SGE RX queues * @data: the adapter * * Runs periodically from a timer to perform maintenance of SGE RX queues. * * a) Replenishes RX queues that have run out due to memory shortage. * Normally new RX buffers are added when existing ones are consumed but * when out of memory a queue can become empty. We schedule NAPI to do * the actual refill. */ static void sge_rx_timer_cb(unsigned long data) { struct adapter *adapter = (struct adapter *)data; struct sge *s = &adapter->sge; unsigned int i; /* * Scan the "Starving Free Lists" flag array looking for any Free * Lists in need of more free buffers. If we find one and it's not * being actively polled, then bump its "starving" counter and attempt * to refill it. If we're successful in adding enough buffers to push * the Free List over the starving threshold, then we can clear its * "starving" status. */ for (i = 0; i < ARRAY_SIZE(s->starving_fl); i++) { unsigned long m; for (m = s->starving_fl[i]; m; m &= m - 1) { unsigned int id = __ffs(m) + i * BITS_PER_LONG; struct sge_fl *fl = s->egr_map[id]; clear_bit(id, s->starving_fl); smp_mb__after_atomic(); /* * Since we are accessing fl without a lock there's a * small probability of a false positive where we * schedule napi but the FL is no longer starving. * No biggie. */ if (fl_starving(adapter, fl)) { struct sge_eth_rxq *rxq; rxq = container_of(fl, struct sge_eth_rxq, fl); if (napi_reschedule(&rxq->rspq.napi)) fl->starving++; else set_bit(id, s->starving_fl); } } } /* * Reschedule the next scan for starving Free Lists ... */ mod_timer(&s->rx_timer, jiffies + RX_QCHECK_PERIOD); } /** * sge_tx_timer_cb - perform periodic maintenance of SGE Tx queues * @data: the adapter * * Runs periodically from a timer to perform maintenance of SGE TX queues. * * b) Reclaims completed Tx packets for the Ethernet queues. Normally * packets are cleaned up by new Tx packets, this timer cleans up packets * when no new packets are being submitted. This is essential for pktgen, * at least. */ static void sge_tx_timer_cb(unsigned long data) { struct adapter *adapter = (struct adapter *)data; struct sge *s = &adapter->sge; unsigned int i, budget; budget = MAX_TIMER_TX_RECLAIM; i = s->ethtxq_rover; do { struct sge_eth_txq *txq = &s->ethtxq[i]; if (reclaimable(&txq->q) && __netif_tx_trylock(txq->txq)) { int avail = reclaimable(&txq->q); if (avail > budget) avail = budget; free_tx_desc(adapter, &txq->q, avail, true); txq->q.in_use -= avail; __netif_tx_unlock(txq->txq); budget -= avail; if (!budget) break; } i++; if (i >= s->ethqsets) i = 0; } while (i != s->ethtxq_rover); s->ethtxq_rover = i; /* * If we found too many reclaimable packets schedule a timer in the * near future to continue where we left off. Otherwise the next timer * will be at its normal interval. */ mod_timer(&s->tx_timer, jiffies + (budget ? TX_QCHECK_PERIOD : 2)); } /** * bar2_address - return the BAR2 address for an SGE Queue's Registers * @adapter: the adapter * @qid: the SGE Queue ID * @qtype: the SGE Queue Type (Egress or Ingress) * @pbar2_qid: BAR2 Queue ID or 0 for Queue ID inferred SGE Queues * * Returns the BAR2 address for the SGE Queue Registers associated with * @qid. If BAR2 SGE Registers aren't available, returns NULL. Also * returns the BAR2 Queue ID to be used with writes to the BAR2 SGE * Queue Registers. If the BAR2 Queue ID is 0, then "Inferred Queue ID" * Registers are supported (e.g. the Write Combining Doorbell Buffer). */ static void __iomem *bar2_address(struct adapter *adapter, unsigned int qid, enum t4_bar2_qtype qtype, unsigned int *pbar2_qid) { u64 bar2_qoffset; int ret; ret = t4_bar2_sge_qregs(adapter, qid, qtype, &bar2_qoffset, pbar2_qid); if (ret) return NULL; return adapter->bar2 + bar2_qoffset; } /** * t4vf_sge_alloc_rxq - allocate an SGE RX Queue * @adapter: the adapter * @rspq: pointer to to the new rxq's Response Queue to be filled in * @iqasynch: if 0, a normal rspq; if 1, an asynchronous event queue * @dev: the network device associated with the new rspq * @intr_dest: MSI-X vector index (overriden in MSI mode) * @fl: pointer to the new rxq's Free List to be filled in * @hnd: the interrupt handler to invoke for the rspq */ int t4vf_sge_alloc_rxq(struct adapter *adapter, struct sge_rspq *rspq, bool iqasynch, struct net_device *dev, int intr_dest, struct sge_fl *fl, rspq_handler_t hnd) { struct sge *s = &adapter->sge; struct port_info *pi = netdev_priv(dev); struct fw_iq_cmd cmd, rpl; int ret, iqandst, flsz = 0; /* * If we're using MSI interrupts and we're not initializing the * Forwarded Interrupt Queue itself, then set up this queue for * indirect interrupts to the Forwarded Interrupt Queue. Obviously * the Forwarded Interrupt Queue must be set up before any other * ingress queue ... */ if ((adapter->flags & USING_MSI) && rspq != &adapter->sge.intrq) { iqandst = SGE_INTRDST_IQ; intr_dest = adapter->sge.intrq.abs_id; } else iqandst = SGE_INTRDST_PCI; /* * Allocate the hardware ring for the Response Queue. The size needs * to be a multiple of 16 which includes the mandatory status entry * (regardless of whether the Status Page capabilities are enabled or * not). */ rspq->size = roundup(rspq->size, 16); rspq->desc = alloc_ring(adapter->pdev_dev, rspq->size, rspq->iqe_len, 0, &rspq->phys_addr, NULL, 0); if (!rspq->desc) return -ENOMEM; /* * Fill in the Ingress Queue Command. Note: Ideally this code would * be in t4vf_hw.c but there are so many parameters and dependencies * on our Linux SGE state that we would end up having to pass tons of * parameters. We'll have to think about how this might be migrated * into OS-independent common code ... */ memset(&cmd, 0, sizeof(cmd)); cmd.op_to_vfn = cpu_to_be32(FW_CMD_OP_V(FW_IQ_CMD) | FW_CMD_REQUEST_F | FW_CMD_WRITE_F | FW_CMD_EXEC_F); cmd.alloc_to_len16 = cpu_to_be32(FW_IQ_CMD_ALLOC_F | FW_IQ_CMD_IQSTART_F | FW_LEN16(cmd)); cmd.type_to_iqandstindex = cpu_to_be32(FW_IQ_CMD_TYPE_V(FW_IQ_TYPE_FL_INT_CAP) | FW_IQ_CMD_IQASYNCH_V(iqasynch) | FW_IQ_CMD_VIID_V(pi->viid) | FW_IQ_CMD_IQANDST_V(iqandst) | FW_IQ_CMD_IQANUS_V(1) | FW_IQ_CMD_IQANUD_V(SGE_UPDATEDEL_INTR) | FW_IQ_CMD_IQANDSTINDEX_V(intr_dest)); cmd.iqdroprss_to_iqesize = cpu_to_be16(FW_IQ_CMD_IQPCIECH_V(pi->port_id) | FW_IQ_CMD_IQGTSMODE_F | FW_IQ_CMD_IQINTCNTTHRESH_V(rspq->pktcnt_idx) | FW_IQ_CMD_IQESIZE_V(ilog2(rspq->iqe_len) - 4)); cmd.iqsize = cpu_to_be16(rspq->size); cmd.iqaddr = cpu_to_be64(rspq->phys_addr); if (fl) { /* * Allocate the ring for the hardware free list (with space * for its status page) along with the associated software * descriptor ring. The free list size needs to be a multiple * of the Egress Queue Unit. */ fl->size = roundup(fl->size, FL_PER_EQ_UNIT); fl->desc = alloc_ring(adapter->pdev_dev, fl->size, sizeof(__be64), sizeof(struct rx_sw_desc), &fl->addr, &fl->sdesc, s->stat_len); if (!fl->desc) { ret = -ENOMEM; goto err; } /* * Calculate the size of the hardware free list ring plus * Status Page (which the SGE will place after the end of the * free list ring) in Egress Queue Units. */ flsz = (fl->size / FL_PER_EQ_UNIT + s->stat_len / EQ_UNIT); /* * Fill in all the relevant firmware Ingress Queue Command * fields for the free list. */ cmd.iqns_to_fl0congen = cpu_to_be32( FW_IQ_CMD_FL0HOSTFCMODE_V(SGE_HOSTFCMODE_NONE) | FW_IQ_CMD_FL0PACKEN_F | FW_IQ_CMD_FL0PADEN_F); cmd.fl0dcaen_to_fl0cidxfthresh = cpu_to_be16( FW_IQ_CMD_FL0FBMIN_V(SGE_FETCHBURSTMIN_64B) | FW_IQ_CMD_FL0FBMAX_V(SGE_FETCHBURSTMAX_512B)); cmd.fl0size = cpu_to_be16(flsz); cmd.fl0addr = cpu_to_be64(fl->addr); } /* * Issue the firmware Ingress Queue Command and extract the results if * it completes successfully. */ ret = t4vf_wr_mbox(adapter, &cmd, sizeof(cmd), &rpl); if (ret) goto err; netif_napi_add(dev, &rspq->napi, napi_rx_handler, 64); rspq->cur_desc = rspq->desc; rspq->cidx = 0; rspq->gen = 1; rspq->next_intr_params = rspq->intr_params; rspq->cntxt_id = be16_to_cpu(rpl.iqid); rspq->bar2_addr = bar2_address(adapter, rspq->cntxt_id, T4_BAR2_QTYPE_INGRESS, &rspq->bar2_qid); rspq->abs_id = be16_to_cpu(rpl.physiqid); rspq->size--; /* subtract status entry */ rspq->adapter = adapter; rspq->netdev = dev; rspq->handler = hnd; /* set offset to -1 to distinguish ingress queues without FL */ rspq->offset = fl ? 0 : -1; if (fl) { fl->cntxt_id = be16_to_cpu(rpl.fl0id); fl->avail = 0; fl->pend_cred = 0; fl->pidx = 0; fl->cidx = 0; fl->alloc_failed = 0; fl->large_alloc_failed = 0; fl->starving = 0; /* Note, we must initialize the BAR2 Free List User Doorbell * information before refilling the Free List! */ fl->bar2_addr = bar2_address(adapter, fl->cntxt_id, T4_BAR2_QTYPE_EGRESS, &fl->bar2_qid); refill_fl(adapter, fl, fl_cap(fl), GFP_KERNEL); } return 0; err: /* * An error occurred. Clean up our partial allocation state and * return the error. */ if (rspq->desc) { dma_free_coherent(adapter->pdev_dev, rspq->size * rspq->iqe_len, rspq->desc, rspq->phys_addr); rspq->desc = NULL; } if (fl && fl->desc) { kfree(fl->sdesc); fl->sdesc = NULL; dma_free_coherent(adapter->pdev_dev, flsz * EQ_UNIT, fl->desc, fl->addr); fl->desc = NULL; } return ret; } /** * t4vf_sge_alloc_eth_txq - allocate an SGE Ethernet TX Queue * @adapter: the adapter * @txq: pointer to the new txq to be filled in * @devq: the network TX queue associated with the new txq * @iqid: the relative ingress queue ID to which events relating to * the new txq should be directed */ int t4vf_sge_alloc_eth_txq(struct adapter *adapter, struct sge_eth_txq *txq, struct net_device *dev, struct netdev_queue *devq, unsigned int iqid) { struct sge *s = &adapter->sge; int ret, nentries; struct fw_eq_eth_cmd cmd, rpl; struct port_info *pi = netdev_priv(dev); /* * Calculate the size of the hardware TX Queue (including the Status * Page on the end of the TX Queue) in units of TX Descriptors. */ nentries = txq->q.size + s->stat_len / sizeof(struct tx_desc); /* * Allocate the hardware ring for the TX ring (with space for its * status page) along with the associated software descriptor ring. */ txq->q.desc = alloc_ring(adapter->pdev_dev, txq->q.size, sizeof(struct tx_desc), sizeof(struct tx_sw_desc), &txq->q.phys_addr, &txq->q.sdesc, s->stat_len); if (!txq->q.desc) return -ENOMEM; /* * Fill in the Egress Queue Command. Note: As with the direct use of * the firmware Ingress Queue COmmand above in our RXQ allocation * routine, ideally, this code would be in t4vf_hw.c. Again, we'll * have to see if there's some reasonable way to parameterize it * into the common code ... */ memset(&cmd, 0, sizeof(cmd)); cmd.op_to_vfn = cpu_to_be32(FW_CMD_OP_V(FW_EQ_ETH_CMD) | FW_CMD_REQUEST_F | FW_CMD_WRITE_F | FW_CMD_EXEC_F); cmd.alloc_to_len16 = cpu_to_be32(FW_EQ_ETH_CMD_ALLOC_F | FW_EQ_ETH_CMD_EQSTART_F | FW_LEN16(cmd)); cmd.viid_pkd = cpu_to_be32(FW_EQ_ETH_CMD_AUTOEQUEQE_F | FW_EQ_ETH_CMD_VIID_V(pi->viid)); cmd.fetchszm_to_iqid = cpu_to_be32(FW_EQ_ETH_CMD_HOSTFCMODE_V(SGE_HOSTFCMODE_STPG) | FW_EQ_ETH_CMD_PCIECHN_V(pi->port_id) | FW_EQ_ETH_CMD_IQID_V(iqid)); cmd.dcaen_to_eqsize = cpu_to_be32(FW_EQ_ETH_CMD_FBMIN_V(SGE_FETCHBURSTMIN_64B) | FW_EQ_ETH_CMD_FBMAX_V(SGE_FETCHBURSTMAX_512B) | FW_EQ_ETH_CMD_CIDXFTHRESH_V( SGE_CIDXFLUSHTHRESH_32) | FW_EQ_ETH_CMD_EQSIZE_V(nentries)); cmd.eqaddr = cpu_to_be64(txq->q.phys_addr); /* * Issue the firmware Egress Queue Command and extract the results if * it completes successfully. */ ret = t4vf_wr_mbox(adapter, &cmd, sizeof(cmd), &rpl); if (ret) { /* * The girmware Ingress Queue Command failed for some reason. * Free up our partial allocation state and return the error. */ kfree(txq->q.sdesc); txq->q.sdesc = NULL; dma_free_coherent(adapter->pdev_dev, nentries * sizeof(struct tx_desc), txq->q.desc, txq->q.phys_addr); txq->q.desc = NULL; return ret; } txq->q.in_use = 0; txq->q.cidx = 0; txq->q.pidx = 0; txq->q.stat = (void *)&txq->q.desc[txq->q.size]; txq->q.cntxt_id = FW_EQ_ETH_CMD_EQID_G(be32_to_cpu(rpl.eqid_pkd)); txq->q.bar2_addr = bar2_address(adapter, txq->q.cntxt_id, T4_BAR2_QTYPE_EGRESS, &txq->q.bar2_qid); txq->q.abs_id = FW_EQ_ETH_CMD_PHYSEQID_G(be32_to_cpu(rpl.physeqid_pkd)); txq->txq = devq; txq->tso = 0; txq->tx_cso = 0; txq->vlan_ins = 0; txq->q.stops = 0; txq->q.restarts = 0; txq->mapping_err = 0; return 0; } /* * Free the DMA map resources associated with a TX queue. */ static void free_txq(struct adapter *adapter, struct sge_txq *tq) { struct sge *s = &adapter->sge; dma_free_coherent(adapter->pdev_dev, tq->size * sizeof(*tq->desc) + s->stat_len, tq->desc, tq->phys_addr); tq->cntxt_id = 0; tq->sdesc = NULL; tq->desc = NULL; } /* * Free the resources associated with a response queue (possibly including a * free list). */ static void free_rspq_fl(struct adapter *adapter, struct sge_rspq *rspq, struct sge_fl *fl) { struct sge *s = &adapter->sge; unsigned int flid = fl ? fl->cntxt_id : 0xffff; t4vf_iq_free(adapter, FW_IQ_TYPE_FL_INT_CAP, rspq->cntxt_id, flid, 0xffff); dma_free_coherent(adapter->pdev_dev, (rspq->size + 1) * rspq->iqe_len, rspq->desc, rspq->phys_addr); netif_napi_del(&rspq->napi); rspq->netdev = NULL; rspq->cntxt_id = 0; rspq->abs_id = 0; rspq->desc = NULL; if (fl) { free_rx_bufs(adapter, fl, fl->avail); dma_free_coherent(adapter->pdev_dev, fl->size * sizeof(*fl->desc) + s->stat_len, fl->desc, fl->addr); kfree(fl->sdesc); fl->sdesc = NULL; fl->cntxt_id = 0; fl->desc = NULL; } } /** * t4vf_free_sge_resources - free SGE resources * @adapter: the adapter * * Frees resources used by the SGE queue sets. */ void t4vf_free_sge_resources(struct adapter *adapter) { struct sge *s = &adapter->sge; struct sge_eth_rxq *rxq = s->ethrxq; struct sge_eth_txq *txq = s->ethtxq; struct sge_rspq *evtq = &s->fw_evtq; struct sge_rspq *intrq = &s->intrq; int qs; for (qs = 0; qs < adapter->sge.ethqsets; qs++, rxq++, txq++) { if (rxq->rspq.desc) free_rspq_fl(adapter, &rxq->rspq, &rxq->fl); if (txq->q.desc) { t4vf_eth_eq_free(adapter, txq->q.cntxt_id); free_tx_desc(adapter, &txq->q, txq->q.in_use, true); kfree(txq->q.sdesc); free_txq(adapter, &txq->q); } } if (evtq->desc) free_rspq_fl(adapter, evtq, NULL); if (intrq->desc) free_rspq_fl(adapter, intrq, NULL); } /** * t4vf_sge_start - enable SGE operation * @adapter: the adapter * * Start tasklets and timers associated with the DMA engine. */ void t4vf_sge_start(struct adapter *adapter) { adapter->sge.ethtxq_rover = 0; mod_timer(&adapter->sge.rx_timer, jiffies + RX_QCHECK_PERIOD); mod_timer(&adapter->sge.tx_timer, jiffies + TX_QCHECK_PERIOD); } /** * t4vf_sge_stop - disable SGE operation * @adapter: the adapter * * Stop tasklets and timers associated with the DMA engine. Note that * this is effective only if measures have been taken to disable any HW * events that may restart them. */ void t4vf_sge_stop(struct adapter *adapter) { struct sge *s = &adapter->sge; if (s->rx_timer.function) del_timer_sync(&s->rx_timer); if (s->tx_timer.function) del_timer_sync(&s->tx_timer); } /** * t4vf_sge_init - initialize SGE * @adapter: the adapter * * Performs SGE initialization needed every time after a chip reset. * We do not initialize any of the queue sets here, instead the driver * top-level must request those individually. We also do not enable DMA * here, that should be done after the queues have been set up. */ int t4vf_sge_init(struct adapter *adapter) { struct sge_params *sge_params = &adapter->params.sge; u32 fl0 = sge_params->sge_fl_buffer_size[0]; u32 fl1 = sge_params->sge_fl_buffer_size[1]; struct sge *s = &adapter->sge; unsigned int ingpadboundary, ingpackboundary; /* * Start by vetting the basic SGE parameters which have been set up by * the Physical Function Driver. Ideally we should be able to deal * with _any_ configuration. Practice is different ... */ if (fl0 != PAGE_SIZE || (fl1 != 0 && fl1 <= fl0)) { dev_err(adapter->pdev_dev, "bad SGE FL buffer sizes [%d, %d]\n", fl0, fl1); return -EINVAL; } if ((sge_params->sge_control & RXPKTCPLMODE_F) == 0) { dev_err(adapter->pdev_dev, "bad SGE CPL MODE\n"); return -EINVAL; } /* * Now translate the adapter parameters into our internal forms. */ if (fl1) s->fl_pg_order = ilog2(fl1) - PAGE_SHIFT; s->stat_len = ((sge_params->sge_control & EGRSTATUSPAGESIZE_F) ? 128 : 64); s->pktshift = PKTSHIFT_G(sge_params->sge_control); /* T4 uses a single control field to specify both the PCIe Padding and * Packing Boundary. T5 introduced the ability to specify these * separately. The actual Ingress Packet Data alignment boundary * within Packed Buffer Mode is the maximum of these two * specifications. (Note that it makes no real practical sense to * have the Pading Boudary be larger than the Packing Boundary but you * could set the chip up that way and, in fact, legacy T4 code would * end doing this because it would initialize the Padding Boundary and * leave the Packing Boundary initialized to 0 (16 bytes).) */ ingpadboundary = 1 << (INGPADBOUNDARY_G(sge_params->sge_control) + INGPADBOUNDARY_SHIFT_X); if (is_t4(adapter->params.chip)) { s->fl_align = ingpadboundary; } else { /* T5 has a different interpretation of one of the PCIe Packing * Boundary values. */ ingpackboundary = INGPACKBOUNDARY_G(sge_params->sge_control2); if (ingpackboundary == INGPACKBOUNDARY_16B_X) ingpackboundary = 16; else ingpackboundary = 1 << (ingpackboundary + INGPACKBOUNDARY_SHIFT_X); s->fl_align = max(ingpadboundary, ingpackboundary); } /* A FL with <= fl_starve_thres buffers is starving and a periodic * timer will attempt to refill it. This needs to be larger than the * SGE's Egress Congestion Threshold. If it isn't, then we can get * stuck waiting for new packets while the SGE is waiting for us to * give it more Free List entries. (Note that the SGE's Egress * Congestion Threshold is in units of 2 Free List pointers.) */ s->fl_starve_thres = EGRTHRESHOLD_G(sge_params->sge_congestion_control)*2 + 1; /* * Set up tasklet timers. */ setup_timer(&s->rx_timer, sge_rx_timer_cb, (unsigned long)adapter); setup_timer(&s->tx_timer, sge_tx_timer_cb, (unsigned long)adapter); /* * Initialize Forwarded Interrupt Queue lock. */ spin_lock_init(&s->intrq_lock); return 0; }