// SPDX-License-Identifier: BSD-3-Clause /* * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. * Copyright (c) 2021-2023, Linaro Limited */ #include #include #include #include / { thermal-zones { pmc8180-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmc8180_temp>; trips { trip0 { temperature = <95000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <115000>; hysteresis = <0>; type = "hot"; }; trip2 { temperature = <145000>; hysteresis = <0>; type = "critical"; }; }; }; pmc8180c-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmc8180c_temp>; trips { trip0 { temperature = <95000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <115000>; hysteresis = <0>; type = "hot"; }; trip2 { temperature = <145000>; hysteresis = <0>; type = "critical"; }; }; }; }; }; &spmi_bus { pmc8180_0: pmic@0 { compatible = "qcom,pm8150", "qcom,spmi-pmic"; reg = <0x0 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pon: pon@800 { compatible = "qcom,pm8916-pon"; reg = <0x0800>; pmc8180_pwrkey: pwrkey { compatible = "qcom,pm8941-pwrkey"; interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; debounce = <15625>; bias-pull-up; linux,code = ; status = "disabled"; }; }; pmc8180_temp: temp-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; reg = <0x2400>; interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; io-channels = <&pmc8180_adc ADC5_DIE_TEMP>; io-channel-names = "thermal"; #thermal-sensor-cells = <0>; }; pmc8180_adc: adc@3100 { compatible = "qcom,spmi-adc5"; reg = <0x3100>; #address-cells = <1>; #size-cells = <0>; #io-channel-cells = <1>; interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; channel@0 { reg = ; qcom,pre-scaling = <1 1>; label = "ref_gnd"; }; channel@1 { reg = ; qcom,pre-scaling = <1 1>; label = "vref_1p25"; }; channel@6 { reg = ; qcom,pre-scaling = <1 1>; label = "die_temp"; }; }; pmc8180_adc_tm: adc-tm@3500 { compatible = "qcom,spmi-adc-tm5"; reg = <0x3500>; interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; #thermal-sensor-cells = <1>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; rtc@6000 { compatible = "qcom,pm8941-rtc"; reg = <0x6000>; reg-names = "rtc", "alarm"; interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; }; pmc8180_1_gpios: gpio@c000 { compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; reg = <0xc000>; gpio-controller; gpio-ranges = <&pmc8180_1_gpios 0 0 10>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; pmic@1 { compatible = "qcom,pmc8180", "qcom,spmi-pmic"; reg = <0x1 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; }; pmic@2 { compatible = "qcom,smb2351", "qcom,spmi-pmic"; reg = <0x2 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; adc@3100 { compatible = "qcom,spmi-adc-rev2"; reg = <0x3100>; #address-cells = <1>; #size-cells = <0>; #io-channel-cells = <1>; interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; channel@0 { reg = ; qcom,pre-scaling = <1 1>; label = "ref_gnd"; }; channel@1 { reg = ; qcom,pre-scaling = <1 1>; label = "vref_1p25"; }; channel@85 { reg = <0x85>; qcom,pre-scaling = <1 1>; label = "vcoin2"; }; }; }; pmic@6 { compatible = "qcom,pm8150c", "qcom,spmi-pmic"; reg = <0x6 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; }; pmc8180_2: pmic@8 { compatible = "qcom,pm8150", "qcom,spmi-pmic"; reg = <0x8 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmc8180_2_gpios: gpio@c000 { compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; reg = <0xc000>; gpio-controller; gpio-ranges = <&pmc8180_2_gpios 0 0 10>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; pmic@a { compatible = "qcom,smb2351", "qcom,spmi-pmic"; reg = <0xa SPMI_USID>; #address-cells = <1>; #size-cells = <0>; adc@3100 { compatible = "qcom,spmi-adc-rev2"; reg = <0x3100>; #address-cells = <1>; #size-cells = <0>; #io-channel-cells = <1>; interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>; channel@0 { reg = ; qcom,pre-scaling = <1 1>; label = "ref_gnd"; }; channel@1 { reg = ; qcom,pre-scaling = <1 1>; label = "vref_1p25"; }; channel@85 { reg = <0x85>; qcom,pre-scaling = <1 1>; label = "vcoin"; }; }; }; pmic@4 { compatible = "qcom,pm8150c", "qcom,spmi-pmic"; reg = <0x4 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pon@800 { compatible = "qcom,pm8916-pon"; reg = <0x0800>; status = "disabled"; }; pmc8180c_temp: temp-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; reg = <0x2400>; interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>; io-channel-names = "thermal"; #thermal-sensor-cells = <0>; }; pmc8180c_adc: adc@3100 { compatible = "qcom,spmi-adc5"; reg = <0x3100>; #address-cells = <1>; #size-cells = <0>; #io-channel-cells = <1>; interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; channel@0 { reg = ; qcom,pre-scaling = <1 1>; label = "ref_gnd"; }; channel@1 { reg = ; qcom,pre-scaling = <1 1>; label = "vref_1p25"; }; channel@6 { reg = ; qcom,pre-scaling = <1 1>; label = "die_temp"; }; }; pmc8180c_adc_tm: adc-tm@3500 { compatible = "qcom,spmi-adc-tm5"; reg = <0x3500>; interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; #thermal-sensor-cells = <1>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; pmc8180c_gpios: gpio@c000 { compatible = "qcom,pmc8180c-gpio", "qcom,spmi-gpio"; reg = <0xc000>; gpio-controller; gpio-ranges = <&pmc8180c_gpios 0 0 12>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; pmic@5 { compatible = "qcom,pmc8180c", "qcom,spmi-pmic"; reg = <0x5 SPMI_USID>; pmc8180c_lpg: pwm { compatible = "qcom,pmc8180c-lpg"; #address-cells = <1>; #size-cells = <0>; #pwm-cells = <2>; status = "disabled"; }; }; };