// SPDX-License-Identifier: BSD-3-Clause /* * Copyright (c) 2023, Linaro Limited */ #include #include / { thermal-zones { pmm8654au_0_thermal: pm8775-0-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmm8654au_0_temp_alarm>; trips { trip0 { temperature = <105000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <125000>; hysteresis = <0>; type = "critical"; }; }; }; pmm8654au_1_thermal: pm8775-1-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmm8654au_1_temp_alarm>; trips { trip0 { temperature = <105000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <125000>; hysteresis = <0>; type = "critical"; }; }; }; pmm8654au_2_thermal: pm8775-2-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmm8654au_2_temp_alarm>; trips { trip0 { temperature = <105000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <125000>; hysteresis = <0>; type = "critical"; }; }; }; pmm8654au_3_thermal: pm8775-3-thermal { polling-delay-passive = <100>; thermal-sensors = <&pmm8654au_3_temp_alarm>; trips { trip0 { temperature = <105000>; hysteresis = <0>; type = "passive"; }; trip1 { temperature = <125000>; hysteresis = <0>; type = "critical"; }; }; }; }; reboot-mode { compatible = "nvmem-reboot-mode"; nvmem-cells = <&reboot_reason>; nvmem-cell-names = "reboot-mode"; mode-recovery = <0x01>; mode-bootloader = <0x02>; }; }; &spmi_bus { pmm8654au_0: pmic@0 { compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; reg = <0x0 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmm8654au_0_temp_alarm: temp-alarm@a00 { compatible = "qcom,spmi-temp-alarm"; reg = <0xa00>; interrupts-extended = <&spmi_bus 0x0 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; pmm8654au_0_pon: pon@1200 { compatible = "qcom,pmk8350-pon"; reg = <0x1200>, <0x800>; reg-names = "hlos", "pbs"; pmm8654au_0_pon_pwrkey: pwrkey { compatible = "qcom,pmk8350-pwrkey"; interrupts-extended = <&spmi_bus 0x0 0x12 0x7 IRQ_TYPE_EDGE_BOTH>; linux,code = ; debounce = <15625>; }; pmm8654au_0_pon_resin: resin { compatible = "qcom,pmk8350-resin"; interrupts-extended = <&spmi_bus 0x0 0x12 0x6 IRQ_TYPE_EDGE_BOTH>; debounce = <15625>; status = "disabled"; }; }; pmm8654au_0_gpios: gpio@8800 { compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; reg = <0x8800>; gpio-controller; gpio-ranges = <&pmm8654au_0_gpios 0 0 12>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; pmm8654au_0_sdam_0: nvram@7100 { compatible = "qcom,spmi-sdam"; reg = <0x7100>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x7100 0x100>; reboot_reason: reboot-reason@48 { reg = <0x48 0x1>; bits = <1 7>; }; }; }; pmm8654au_1: pmic@2 { compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; reg = <0x2 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmm8654au_1_temp_alarm: temp-alarm@a00 { compatible = "qcom,spmi-temp-alarm"; reg = <0xa00>; interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; pmm8654au_1_gpios: gpio@8800 { compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; reg = <0x8800>; gpio-controller; gpio-ranges = <&pmm8654au_1_gpios 0 0 12>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; pmm8654au_2: pmic@4 { compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; reg = <0x4 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmm8654au_2_temp_alarm: temp-alarm@a00 { compatible = "qcom,spmi-temp-alarm"; reg = <0xa00>; interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; pmm8654au_2_gpios: gpio@8800 { compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; reg = <0x8800>; gpio-controller; gpio-ranges = <&pmm8654au_2_gpios 0 0 12>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; pmm8654au_3: pmic@6 { compatible = "qcom,pmm8654au", "qcom,spmi-pmic"; reg = <0x6 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmm8654au_3_temp_alarm: temp-alarm@a00 { compatible = "qcom,spmi-temp-alarm"; reg = <0xa00>; interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; #thermal-sensor-cells = <0>; }; pmm8654au_3_gpios: gpio@8800 { compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio"; reg = <0x8800>; gpio-controller; gpio-ranges = <&pmm8654au_3_gpios 0 0 12>; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; }; };