# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Analog Devices AD7606 Simultaneous Sampling ADC

maintainers:
  - Michael Hennerich <michael.hennerich@analog.com>

description: |
  Analog Devices AD7606 Simultaneous Sampling ADC
  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf
  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf

properties:
  compatible:
    enum:
      - adi,ad7605-4
      - adi,ad7606-4
      - adi,ad7606-6
      - adi,ad7606-8  # Referred to as AD7606 (without -8) in the datasheet
      - adi,ad7606b
      - adi,ad7616

  reg:
    maxItems: 1

  spi-cpha: true

  spi-cpol: true

  avcc-supply: true

  vdrive-supply:
    description:
      Determines the voltage level at which the interface logic pins will
      operate.

  refin-supply:
    description:
      The voltage supply for optional external reference voltage.

  interrupts:
    description:
      The BUSY pin falling edge indicates that the conversion is over, and thus
      new data is available.
    maxItems: 1

  adi,conversion-start-gpios:
    description:
      Must be the device tree identifier of the CONVST pin. This logic input is
      used to initiate conversions on the analog input channels. As the line is
      active high, it should be marked GPIO_ACTIVE_HIGH.
    maxItems: 1

  reset-gpios:
    description:
      Must be the device tree identifier of the RESET pin. If specified, it will
      be asserted during driver probe. On the AD7606x, as the line is active
      high, it should be marked GPIO_ACTIVE_HIGH. On the AD7616, as the line is
      active low, it should be marked GPIO_ACTIVE_LOW.
    maxItems: 1

  standby-gpios:
    description:
      Must be the device tree identifier of the STBY pin. This pin is used to
      place the AD7606 into one of two power-down modes, Standby mode or
      Shutdown mode. As the line is active low, it should be marked
      GPIO_ACTIVE_LOW.
    maxItems: 1

  adi,first-data-gpios:
    description:
      Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA
      output indicates when the first channel, V1, is being read back on either
      the parallel, byte or serial interface. As the line is active high, it
      should be marked GPIO_ACTIVE_HIGH.
    maxItems: 1

  adi,range-gpios:
    description:
      Must be the device tree identifier of the RANGE pin. The state on this
      pin determines the input range of the analog input channels. If this pin
      is tied to a logic high, the analog input range is ±10V for all channels.
      On the AD760X, if this pin is tied to a logic low, the analog input range
      is ±5V for all channels. As the line is active high, it should be marked
      GPIO_ACTIVE_HIGH.
    maxItems: 1

  adi,oversampling-ratio-gpios:
    description:
      Must be the device tree identifier of the over-sampling mode pins. As the
      line is active high, it should be marked GPIO_ACTIVE_HIGH. On the AD7606X
      parts that support it, if all 3 pins are tied to a logic high, software
      mode is enabled.
    maxItems: 3

  adi,sw-mode:
    description:
      Software mode of operation, so far available only for AD7616 and AD7606B.
      It is enabled when all three oversampling mode pins are connected to high
      level for the AD7606B, or both the range selection are connected to high
      level for the AD7616. The device is configured by the corresponding
      registers. If the adi,oversampling-ratio-gpios property is defined, then
      the driver will set the oversampling gpios to high. Otherwise, it is
      assumed that the pins are hardwired to VDD.
    type: boolean

required:
  - compatible
  - reg
  - spi-cpha
  - avcc-supply
  - vdrive-supply
  - interrupts
  - adi,conversion-start-gpios

allOf:
  - $ref: /schemas/spi/spi-peripheral-props.yaml#

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>
    spi {
        #address-cells = <1>;
        #size-cells = <0>;

        adc@0 {
            compatible = "adi,ad7606-8";
            reg = <0>;
            spi-max-frequency = <1000000>;
            spi-cpol;
            spi-cpha;

            avcc-supply = <&adc_vref>;
            vdrive-supply = <&vdd_supply>;

            interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
            interrupt-parent = <&gpio>;

            adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
            reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
            adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
            adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
                                           <&gpio 23 GPIO_ACTIVE_HIGH>,
                                           <&gpio 26 GPIO_ACTIVE_HIGH>;
            standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
        };
    };
...