/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2007 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ /* * Serial I/O driver for Z8530 chips */ #pragma ident "%Z%%M% %I% %E% SMI" #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define ZS_TRACING #ifdef ZS_TRACING #include /* * Temp tracepoint definitions */ #define TR_FAC_ZS 51 #define TR_ZS_H_INT_START 1 #define TR_ZS_H_INT_END 2 #define TR_ZS_INT_START 3 #define TR_ZS_INT_END 4 #define TR_FAC_ZS_INT 52 #define TR_READ_START 1 #define TR_READ_END 2 #endif /* ZSH_TRACING */ #define KIOIP KSTAT_INTR_PTR(zs->intrstats) #ifndef MAXZS #define MAXZS 4 #endif int maxzs = MAXZS; int nzs = 0; struct zscom *zscom; struct zscom *zscurr; struct zscom *zslast; struct zs_prog *zs_prog; char *zssoftCAR; int zs_watchdog_count = 10; /* countdown to determine if tx hung */ int zs_drain_check = 15000000; /* tunable: exit drain check time */ #ifdef ZS_DEBUG char zs_h_log[ZS_H_LOG_MAX +10]; int zs_h_log_n = 0; #define zs_h_log_add(c) \ { \ if (zs_h_log_n >= ZS_H_LOG_MAX) \ zs_h_log_n = 0; \ zs_h_log[zs_h_log_n++] = c; \ zs_h_log[zs_h_log_n] = '\0'; \ } #else /* NO_ZS_DEBUG */ #define zs_h_log_add(c) #endif /* ZS_DEBUG */ /* * Driver data */ #define GETPROP(dip, str, defval) \ ddi_getprop(DDI_DEV_T_ANY, (dip), DDI_PROP_DONTPASS, (str), (defval)) int zs_usec_delay = 1; int zssoftpend; ddi_softintr_t zs_softintr_id; time_t default_dtrlow = 3; /* hold dtr low nearly this long on close */ static ddi_iblock_cookie_t zs_iblock; static ddi_iblock_cookie_t zs_hi_iblock; static int zs_addedsoft = 0; /* * Driver information for auto-configuration stuff. */ static int zsprobe(dev_info_t *dev); static int zsattach(dev_info_t *dev, ddi_attach_cmd_t cmd); static int zsdetach(dev_info_t *dev, ddi_detach_cmd_t cmd); void zsopinit(struct zscom *zs, struct zsops *zso); static void zsnull_intr(struct zscom *zs); static int zsnull_softint(struct zscom *zs); static int zsnull_suspend(struct zscom *zs); static int zsnull_resume(struct zscom *zs); struct zsops zsops_null = { zsnull_intr, zsnull_intr, zsnull_intr, zsnull_intr, zsnull_softint, zsnull_suspend, zsnull_resume }; extern struct streamtab asynctab; /* default -- from zs_async.c */ uint_t zs_high_intr(caddr_t argzs); uint_t zsintr(caddr_t intarg); extern int zsc_info(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, void **result); extern int ddi_create_internal_pathname(dev_info_t *dip, char *name, int spec_type, minor_t minor_num); extern struct streamtab zsstab; int zssoftpend; /* soft interrupt pending */ kmutex_t zs_soft_lock; /* adapt.lock,to use to protect data */ /* common to sev. streams or ports */ kmutex_t zs_curr_lock; /* lock protecting zscurr */ extern kcondvar_t lbolt_cv; /* * curently the only spin lock level 12 for all ocasions */ #define ZSS_CONF_FLAG (D_NEW | D_MP) static struct cb_ops cb_zs_ops = { nulldev, /* cb_open */ nulldev, /* cb_close */ nodev, /* cb_strategy */ nodev, /* cb_print */ nodev, /* cb_dump */ nodev, /* cb_read */ nodev, /* cb_write */ nodev, /* cb_ioctl */ nodev, /* cb_devmap */ nodev, /* cb_mmap */ nodev, /* cb_segmap */ nochpoll, /* cb_chpoll */ ddi_prop_op, /* cb_prop_op */ &asynctab, /* cb_stream */ (int)(ZSS_CONF_FLAG) /* cb_flag */ }; struct dev_ops zs_ops = { DEVO_REV, /* devo_rev */ 0, /* devo_refcnt */ zsc_info, /* devo_getinfo */ nulldev, /* devo_identify */ zsprobe, /* devo_probe */ zsattach, /* devo_attach */ zsdetach, /* devo_detach */ nodev, /* devo_reset */ &cb_zs_ops, /* devo_cb_ops */ (struct bus_ops *)NULL, /* devo_bus_ops */ ddi_power /* devo_power */ }; /* * This is the loadable module wrapper. */ #include /* * Module linkage information for the kernel. */ extern struct mod_ops mod_driverops; static struct modldrv modldrv = { &mod_driverops, /* Type of module. This one is a driver */ "Z8530 serial driver V%I%", &zs_ops, /* driver ops */ }; static struct modlinkage modlinkage = { MODREV_1, (void *)&modldrv, NULL }; int _init(void) { return (mod_install(&modlinkage)); } int _fini(void) { return (EBUSY); } int _info(struct modinfo *modinfop) { return (mod_info(&modlinkage, modinfop)); } static int zsprobe(dev_info_t *dev) { struct zscc_device *zsaddr; int rval; auto char c; rval = DDI_PROBE_FAILURE; /* * temporarily map in registers */ if (ddi_map_regs(dev, 0, (caddr_t *)&zsaddr, 0, 0)) { cmn_err(CE_WARN, "zsprobe: unable to map registers"); return (rval); } /* * NON-DDI Compliant call */ mon_clock_stop(); /* * get in sync with the chip */ if (ddi_peek8(dev, (char *)&zsaddr->zscc_control, &c) != DDI_SUCCESS) { goto out; } drv_usecwait(2); /* * The traditional test for the presence of an 8530 has been to write * a 15 (octal 017) to its control register address, then read it back. * A Z8530 will respond to this with the contents of Read-Register 15. * If this address were memory, or something else, we would expect to * see the 15 again. Normally, the contents of RR15 will be entirely * different. A Z8530 does not use the D0 and D2 bits of register 15, * so they should equal zero. Compatable chips should do the same. * Beware of "enhanced" SCC's that do not guarantee this. */ if (ddi_poke8(dev, (char *)&zsaddr->zscc_control, '\017') != DDI_SUCCESS) { goto out; } drv_usecwait(2); if (ddi_peek8(dev, (char *)&zsaddr->zscc_control, &c) != DDI_SUCCESS) { goto out; } drv_usecwait(2); if (c & 5) { goto out; } rval = DDI_PROBE_SUCCESS; out: /* * NON-DDI Compliant call */ mon_clock_start(); ddi_unmap_regs(dev, 0, (caddr_t *)&zsaddr, 0, 0); return (rval); } /*ARGSUSED*/ static int zsattach(dev_info_t *dev, ddi_attach_cmd_t cmd) { struct zscom *zs; int loops, i; uint_t s; int rtsdtr_bits = 0; char softcd; uchar_t rr; short speed[2]; int current_chip = ddi_get_instance(dev); struct zscc_device *tmpzs; /* for mapping purposes */ char name[16]; int keyboard_prop; switch (cmd) { case DDI_ATTACH: break; case DDI_RESUME: zs = &zscom[current_chip*2]; /* * Try to resume first channel */ if (!zs->zs_resume || (zs->zs_resume)(zs) != DDI_SUCCESS) return (DDI_FAILURE); /* * And the second channel */ zs++; if (!zs->zs_resume || (zs->zs_resume)(zs) != DDI_SUCCESS) { zs--; if (!zs->zs_suspend || (zs->zs_suspend)(zs) != DDI_SUCCESS) cmn_err(CE_WARN, "zs: inconsistent suspend/resume state"); return (DDI_FAILURE); } return (DDI_SUCCESS); default: return (DDI_FAILURE); } if (zscom == NULL) { mutex_init(&zs_soft_lock, NULL, MUTEX_DRIVER, (void *)ZS_PL); mutex_init(&zs_curr_lock, NULL, MUTEX_DRIVER, (void *)ZS_PL_HI); zscom = kmem_zalloc(maxzs * sizeof (struct zscom), KM_SLEEP); zs_prog = kmem_zalloc(maxzs * sizeof (struct zs_prog), KM_SLEEP); zssoftCAR = kmem_zalloc(maxzs, KM_SLEEP); /* don't set nzs until arrays are allocated */ membar_producer(); nzs = maxzs; zscurr = &zscom[(current_chip*2) + 1]; zslast = &zscom[current_chip*2]; i = GETPROP(dev, "zs-usec-delay", 0); zs_usec_delay = (i <= 0) ? 1 : i; } if (2 * current_chip >= maxzs) { cmn_err(CE_WARN, "zs: unable to allocate resources for chip %d.", current_chip); cmn_err(CE_WARN, "Change zs:maxzs in /etc/system"); return (DDI_FAILURE); } zs = &zscom[current_chip*2]; /* * map in the device registers */ if (ddi_map_regs(dev, 0, (caddr_t *)&zs->zs_addr, 0, 0)) { cmn_err(CE_WARN, "zs%d: unable to map registers\n", current_chip); return (DDI_FAILURE); } tmpzs = zs->zs_addr; /* * Non-DDI compliant Sun-Ness specfic call(s) */ /* * Stop the monitor's polling interrupt. * * I know that this is not exactly obvious. On all sunmon PROM * machines, the PROM has can have a high level periodic clock * interrupt going at this time. It uses this periodic interrupt * to poll the console tty or kbd uart to check for things like * BREAK or L1-A (abort). While we're probing this device out we * have to shut that off so the PROM won't get confused by what * we're doing to the zs. This has caused some pretty funny bugs * in its time. * * For OPENPROM machines, the prom takes level12 interrupts directly, * but we call this routine anyway (I forget why). */ mon_clock_stop(); /* * Go critical to keep uart from urking. */ s = ddi_enter_critical(); /* * We are about to issue a full reset to this chip. * First, now that interrupts are blocked, we will delay up to a * half-second, checking both channels for any stray activity. * Next we will preserve the time constants from both channels, * so that they can be restored after the reset. This is especially * important for the console device. Finally, do the reset and * follow it with an extended recovery while the chip settles down. */ for (loops = 0; loops++ <= 500; DELAY(1000)) { SCC_READA(1, rr); if ((rr & ZSRR1_ALL_SENT) == 0) continue; SCC_READB(1, rr); if ((rr & ZSRR1_ALL_SENT) == 0) continue; SCC_READA(0, rr); if ((rr & ZSRR0_TX_READY) == 0) continue; SCC_READB(0, rr); if ((rr & ZSRR0_TX_READY) != 0) break; } SCC_READA(12, speed[0]); SCC_READA(13, rr); speed[0] |= rr << 8; SCC_READB(12, speed[1]); SCC_READB(13, rr); speed[1] |= rr << 8; SCC_WRITE(9, ZSWR9_RESET_WORLD); DELAY(10); /* * Set up the other components of the zscom structs for this chip. */ for (i = 0; i < 2; i++) { /* * Property for ignoring DCD. * We switch between 'a' and 'b' ports for this device. */ static char prop[] = "port-a-ignore-cd"; /* * For this channel, set the hardware address, allocate the * high-level mutex, and update the zscurr pointer. * The high-level lock is shared by both channels because * 8530 register addressing is non-atomic and asymetrical. * Multiple threads crossing paths during this operation * could trash the chip, and thus, possibly the system console. */ if (i == 0) { /* port A */ zs->zs_addr = (struct zscc_device *) ((uintptr_t)tmpzs | ZSOFF); (zs+1)->zs_excl_hi = zs->zs_excl_hi = &zs_curr_lock; } else { /* port B */ zs++; zs->zs_addr = (struct zscc_device *) ((uintptr_t)tmpzs & ~ZSOFF); zscurr = zs; } zs->zs_unit = current_chip * 2 + i; zs->zs_dip = dev; zs->zs_excl = kmem_zalloc(sizeof (kmutex_t), KM_SLEEP); mutex_init(zs->zs_excl, NULL, MUTEX_DRIVER, (void *)ZS_PL); zs->zs_ocexcl = kmem_zalloc(sizeof (kmutex_t), KM_SLEEP); mutex_init(zs->zs_ocexcl, NULL, MUTEX_DRIVER, (void *)ZS_PL); zsopinit(zs, &zsops_null); prop[5] = 'a' + i; softcd = GETPROP((dev_info_t *)(dev), prop, 0); zssoftCAR[zs->zs_unit] = softcd; if (softcd) rtsdtr_bits = ZSWR5_RTS | ZSWR5_DTR; keyboard_prop = GETPROP((dev_info_t *)(zs->zs_dip), "keyboard", 0); mutex_enter(&zs_curr_lock); /* * Set up the default asynch modes * so the monitor will still work */ SCC_WRITE(4, ZSWR4_PARITY_EVEN | ZSWR4_1_STOP | ZSWR4_X16_CLK); SCC_WRITE(3, ZSWR3_RX_8); SCC_WRITE(11, ZSWR11_TXCLK_BAUD | ZSWR11_RXCLK_BAUD); SCC_WRITE(12, (speed[i] & 0xff)); SCC_WRITE(13, (speed[i] >> 8) & 0xff); SCC_WRITE(14, ZSWR14_BAUD_FROM_PCLK); SCC_WRITE(3, ZSWR3_RX_8 | ZSWR3_RX_ENABLE); SCC_WRITE(5, ZSWR5_TX_ENABLE | ZSWR5_TX_8 | rtsdtr_bits); SCC_WRITE(14, ZSWR14_BAUD_ENA | ZSWR14_BAUD_FROM_PCLK); /* * The SYNC pin on the second SCC (keyboard & mouse) may not * be connected and noise creates transitions on this line. * This floods the system with interrupts, unless the * Sync/Hunt Interrupt Enable is cleared. So write * register 15 with everything we need but that one. */ if (keyboard_prop) { SCC_WRITE(15, ZSR15_BREAK | ZSR15_TX_UNDER | ZSR15_CTS | ZSR15_CD); } SCC_WRITE0(ZSWR0_RESET_ERRORS); SCC_WRITE0(ZSWR0_RESET_STATUS); mutex_exit(&zs_curr_lock); zs->zs_dtrlow = gethrestime_sec() - default_dtrlow; cv_init(&zs->zs_flags_cv, NULL, CV_DEFAULT, NULL); zsa_init(zs); } mutex_enter(&zs_curr_lock); SCC_WRITE(9, ZSWR9_MASTER_IE | ZSWR9_VECTOR_INCL_STAT); DELAY(4000); mutex_exit(&zs_curr_lock); /* * Two levels of interrupt - chip interrupts at a high level (12), * (which is seen below as zs_high_intr), and then as a secondary * stage soft interrupt as seen in zsintr below. * * Because zs_high_intr does a window save, as well as calls to * other functions, we cannot install it as a "fast" interrupt * that would execute right out of the trap window. Too bad... */ if (ddi_add_intr(dev, (uint_t)0, &zs_hi_iblock, (ddi_idevice_cookie_t *)0, zs_high_intr, (caddr_t)0) != DDI_SUCCESS) { cmn_err(CE_PANIC, "cannot set high level zs interrupt"); /*NOTREACHED*/ } if (zs_addedsoft == 0) { if (ddi_add_softintr(dev, DDI_SOFTINT_HIGH, &zs_softintr_id, &zs_iblock, (ddi_idevice_cookie_t *)0, zsintr, (caddr_t)0) != DDI_SUCCESS) { cmn_err(CE_PANIC, "cannot set second stage zs interrupt"); /*NOTREACHED*/ } zs_addedsoft++; /* we only need one zsintr! */ } if (zs > zslast) zslast = zs; (void) ddi_exit_critical(s); /* * Non-DDI compliant Sun-Ness specific call */ mon_clock_start(); /* re-enable monitor's polling interrupt */ if (!GETPROP(zs->zs_dip, "keyboard", 0)) { static char *serial_line = DDI_NT_SERIAL_MB; static char *dial_out = DDI_NT_SERIAL_MB_DO; /* * Export names for channel a or b consconfig match... * The names exported to the filesystem include the * designated tty'a' type name and may not match the PROM * pathname. * Note the special name "obp-console-name" used in these calls. * This keeps the ports and devlinks programs from seeing these * names. (But allows ddi_pathname_to_dev_t to see them.) * We don't need to do this if the instance number is zero, * because we'll create them below, in this case. */ if (ddi_get_instance(dev) != 0) { /* * Select a node type unused by ddi/devfs */ static char *obp_type = "obp-console-name"; (void) strcpy(name, "a"); if (ddi_create_minor_node(dev, name, S_IFCHR, ddi_get_instance(dev) * 2, obp_type, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } (void) strcpy(name, "b"); if (ddi_create_minor_node(dev, name, S_IFCHR, (ddi_get_instance(dev) * 2) + 1, obp_type, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } } /* * Export normal device names... */ (void) sprintf(name, "%c", (ddi_get_instance(dev) + 'a')); if (ddi_create_minor_node(dev, name, S_IFCHR, ddi_get_instance(dev) * 2, serial_line, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } (void) sprintf(name, "%c", (ddi_get_instance(dev) + 'b')); if (ddi_create_minor_node(dev, name, S_IFCHR, (ddi_get_instance(dev) * 2) + 1, serial_line, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } (void) sprintf(name, "%c,cu", (ddi_get_instance(dev) + 'a')); if (ddi_create_minor_node(dev, name, S_IFCHR, (ddi_get_instance(dev) * 2) | OUTLINE, dial_out, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } (void) sprintf(name, "%c,cu", (ddi_get_instance(dev) + 'b')); if (ddi_create_minor_node(dev, name, S_IFCHR, ((ddi_get_instance(dev) * 2) + 1) | OUTLINE, dial_out, NULL) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } } else { /* * Create keyboard and mouse nodes which devfs doesn't see */ /* * This set of minor nodes is for use with the consconfig_dacf * module for the sun4u platforms. (See PSARC/1998/212) */ if (ddi_create_internal_pathname(dev, "keyboard", S_IFCHR, ddi_get_instance(dev) * 2) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } if (ddi_create_internal_pathname(dev, "mouse", S_IFCHR, (ddi_get_instance(dev) * 2) + 1) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } /* * These minor nodes are for use with pre-sun4u platforms. * Either one set or the other will be opened by consconfig. */ (void) strcpy(name, "a"); if (ddi_create_internal_pathname(dev, name, S_IFCHR, ddi_get_instance(dev) * 2) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } (void) strcpy(name, "b"); if (ddi_create_internal_pathname(dev, name, S_IFCHR, (ddi_get_instance(dev) * 2) + 1) == DDI_FAILURE) { ddi_remove_minor_node(dev, NULL); return (DDI_FAILURE); } } ddi_report_dev(dev); /* * Initialize power management bookkeeping; components are * created idle. */ if (pm_create_components(dev, 3) == DDI_SUCCESS) { (void) pm_busy_component(dev, 0); pm_set_normal_power(dev, 0, 1); pm_set_normal_power(dev, 1, 1); pm_set_normal_power(dev, 2, 1); } else { return (DDI_FAILURE); } (void) sprintf(name, "zsc%d", current_chip); zs->intrstats = kstat_create("zs", current_chip, name, "controller", KSTAT_TYPE_INTR, 1, KSTAT_FLAG_PERSISTENT); if (zs->intrstats) { kstat_install(zs->intrstats); } return (DDI_SUCCESS); } static int zsdetach(dev_info_t *dev, ddi_detach_cmd_t cmd) { struct zscom *zs; int current_chip = ddi_get_instance(dev); switch (cmd) { case DDI_DETACH: return (DDI_FAILURE); case DDI_SUSPEND: zs = &zscom[current_chip*2]; /* * Try to suspend first channel */ if (!zs->zs_suspend || (zs->zs_suspend)(zs) != DDI_SUCCESS) return (DDI_FAILURE); /* * And the second channel */ zs++; if (!zs->zs_suspend || (zs->zs_suspend)(zs) != DDI_SUCCESS) { zs--; if (!zs->zs_resume || (zs->zs_resume)(zs) != DDI_SUCCESS) cmn_err(CE_WARN, "zs: inconsistent suspend/resume state"); return (DDI_FAILURE); } return (DDI_SUCCESS); default: return (DDI_FAILURE); } } /* * SCC High Level Interrupt Handler * * This routine fields the level 12 interrupts generated by the 8530 chips. * When the SCC interrupts the conditions that triggered it are available * for reference in Read Register 3 of the A channel (RR3A). We process * all the pending interrupts before returning. The maximum interrupts * that will be processed before returning is set to 6, which is twice * the size of RX-FIFO. * We keep a pointer to the B side of the most recently interrupting chip * in zscurr. */ /* * 'argzs' actually 'struct zscom *argzs' */ #define ZSRR3_INT_PENDING (ZSRR3_IP_B_STAT | ZSRR3_IP_B_TX | ZSRR3_IP_B_RX |\ ZSRR3_IP_A_STAT | ZSRR3_IP_A_TX | ZSRR3_IP_A_RX) #define ZSRR1_ANY_ERRORS (ZSRR1_PE | ZSRR1_DO | ZSRR1_FE | ZSRR1_RXEOF) #define ZS_HIGH_INTR_LOOPLIMIT 6 /*ARGSUSED*/ uint_t zs_high_intr(caddr_t argzs) { struct zscom *zs; uchar_t stat, isource, count; int unit; TRACE_0(TR_FAC_ZS, TR_ZS_H_INT_START, "zs_h_int start"); mutex_enter(&zs_curr_lock); zs = zscurr; /* Points at Channel B */ ZSNEXTPOLL(zs, zscurr); SCC_READA(3, isource); start_zs_h: count = ZS_HIGH_INTR_LOOPLIMIT; while ((isource & ZSRR3_INT_PENDING) && (count--)) { if (isource & ZSRR3_IP_B_STAT) (zs->zs_xsint)(zs); else { if (isource & ZSRR3_IP_B_TX) (zs->zs_txint)(zs); if (isource & ZSRR3_IP_B_RX) { SCC_READ(1, stat); if (stat & ZSRR1_ANY_ERRORS) (zs->zs_srint)(zs); else if ((SCC_READ0()) & ZSRR0_RX_READY) (zs->zs_rxint)(zs); } } zs -= 1; if (isource & ZSRR3_IP_A_STAT) (zs->zs_xsint)(zs); else { if (isource & ZSRR3_IP_A_TX) (zs->zs_txint)(zs); if (isource & ZSRR3_IP_A_RX) { SCC_READ(1, stat); if (stat & ZSRR1_ANY_ERRORS) (zs->zs_srint)(zs); else if ((SCC_READ0()) & ZSRR0_RX_READY) (zs->zs_rxint)(zs); } } zs = zscurr; SCC_READA(3, isource); } if (count == ZS_HIGH_INTR_LOOPLIMIT) { unit = (nzs >> 1) - 1; while (unit--) { zs += 2; /* Always Channel B */ if (zs > zslast) zs = &zscom[1]; if (!zs->zs_ops) continue; SCC_READA(3, isource); if (isource & ZSRR3_INT_PENDING) { zscurr = zs; /* update zscurr and */ goto start_zs_h; } } if (zs->intrstats) { KIOIP->intrs[KSTAT_INTR_HARD]++; } mutex_exit(&zs_curr_lock); TRACE_0(TR_FAC_ZS, TR_ZS_H_INT_END, "zs_h_int end"); return (DDI_INTR_UNCLAIMED); /* Must not be for us. */ } if (zs->intrstats) { KIOIP->intrs[KSTAT_INTR_HARD]++; } mutex_exit(&zs_curr_lock); /* we're done with zscurr */ TRACE_0(TR_FAC_ZS, TR_ZS_H_INT_END, "zs_h_int end"); return (DDI_INTR_CLAIMED); } /* * Handle a second-stage interrupt. */ /*ARGSUSED*/ uint_t zsintr(caddr_t intarg) { struct zscom *zs; int rv; /* * Test and clear soft interrupt. */ TRACE_0(TR_FAC_ZS, TR_ZS_INT_START, "zs_int start"); mutex_enter(&zs_curr_lock); rv = zssoftpend; if (rv != 0) { zssoftpend = 0; } mutex_exit(&zs_curr_lock); if (rv) { for (zs = &zscom[0]; zs <= zslast; zs++) { if (zs->zs_flags & ZS_NEEDSOFT) { zs->zs_flags &= ~ZS_NEEDSOFT; (*zs->zs_ops->zsop_softint)(zs); if (zs->intrstats) { KIOIP->intrs[KSTAT_INTR_SOFT]++; } } } } TRACE_0(TR_FAC_ZS, TR_ZS_INT_END, "zs_int end"); return (rv); } void setzssoft(void) { ddi_trigger_softintr(zs_softintr_id); } /* * Install a new ops vector into low level vector routine addresses */ void zsopinit(struct zscom *zs, struct zsops *zso) { zs->zs_txint = zso->zsop_txint; zs->zs_xsint = zso->zsop_xsint; zs->zs_rxint = zso->zsop_rxint; zs->zs_srint = zso->zsop_srint; zs->zs_suspend = zso->zsop_suspend; zs->zs_resume = zso->zsop_resume; zs->zs_ops = zso; zs->zs_flags = 0; } /* * Set or get the modem control status. * * This routine relies on the fact that the bits of interest in RR0 (CD and * CTS) do not overlap the bits of interest in WR5 (RTS and DTR). Thus, they * can be combined into a single 'int' without harm. */ int zsmctl(struct zscom *zs, int bits, int how) { int mbits, obits; time_t now, held; ASSERT(mutex_owned(zs->zs_excl_hi)); ASSERT(mutex_owned(zs->zs_excl)); again: mbits = zs->zs_wreg[5] & (ZSWR5_RTS|ZSWR5_DTR); SCC_WRITE0(ZSWR0_RESET_STATUS); mbits |= SCC_READ0() & (ZSRR0_CD|ZSRR0_CTS); ZSDELAY(); obits = mbits; switch (how) { case DMSET: mbits = bits; break; case DMBIS: mbits |= bits; break; case DMBIC: mbits &= ~bits; break; case DMGET: return (mbits); } now = gethrestime_sec(); held = now - zs->zs_dtrlow; /* * if DTR is going low, stash current time away */ if (~mbits & obits & ZSWR5_DTR) zs->zs_dtrlow = now; /* * if DTR is going high, sleep until it has been low a bit */ if ((mbits & ~obits & ZSWR5_DTR) && (held < default_dtrlow)) { mutex_exit(zs->zs_excl_hi); cv_wait(&lbolt_cv, zs->zs_excl); if (zs->zs_suspended) (void) ddi_dev_is_needed(zs->zs_dip, 0, 1); mutex_enter(zs->zs_excl_hi); goto again; } zs->zs_wreg[5] &= ~(ZSWR5_RTS|ZSWR5_DTR); SCC_BIS(5, mbits & (ZSWR5_RTS|ZSWR5_DTR)); return (mbits); } /* * Program the Z8530 registers. */ void zs_program(struct zs_prog *zspp) { struct zscom *zs = zspp->zs; int loops; uchar_t c; uchar_t wr10 = 0, wr14 = 0; ASSERT(mutex_owned(zs->zs_excl)); ASSERT(mutex_owned(zs->zs_excl_hi)); /* * There are some special cases to account for before reprogramming. * We might be transmitting, so delay 100,000 usec (worst case at 110 * baud) for this to finish, then disable the receiver until later, * reset the External Status Change latches and the error bits, and * drain the receive FIFO. * XXX: Doing any kind of reset (WR9) here causes trouble! */ if (zspp->flags & ZSP_SYNC) { SCC_WRITE(7, SDLCFLAG); wr10 = ZSWR10_PRESET_ONES; if (zspp->flags & ZSP_NRZI) wr10 |= ZSWR10_NRZI; SCC_WRITE(10, wr10); } else { for (loops = 1000; loops > 0; --loops) { SCC_READ(1, c); if (c & ZSRR1_ALL_SENT) break; DELAY(100); } SCC_WRITE(3, 0); SCC_WRITE0(ZSWR0_RESET_STATUS); SCC_WRITE0(ZSWR0_RESET_ERRORS); c = SCC_READDATA(); /* Empty the FIFO */ c = SCC_READDATA(); c = SCC_READDATA(); } /* * Programming the SCC is done in three phases. * Phase one sets operating modes: */ SCC_WRITE(4, zspp->wr4); SCC_WRITE(11, zspp->wr11); SCC_WRITE(12, zspp->wr12); SCC_WRITE(13, zspp->wr13); if (zspp->flags & ZSP_PLL) { SCC_WRITE(14, ZSWR14_DPLL_SRC_BAUD); SCC_WRITE(14, ZSWR14_DPLL_NRZI); } else SCC_WRITE(14, ZSWR14_DPLL_DISABLE); /* * Phase two enables special hardware functions: */ wr14 = ZSWR14_BAUD_FROM_PCLK | ZSWR14_BAUD_ENA; if (zspp->flags & ZSP_LOOP) wr14 |= ZSWR14_LOCAL_LOOPBACK; if (zspp->flags & ZSP_ECHO) wr14 |= ZSWR14_AUTO_ECHO; SCC_WRITE(14, wr14); SCC_WRITE(3, zspp->wr3); SCC_WRITE(5, zspp->wr5); SCC_WRITE0(ZSWR0_RESET_TXCRC); if (zspp->flags & ZSP_PARITY_SPECIAL) { SCC_WRITE(1, ZSWR1_PARITY_SPECIAL); } else { SCC_WRITE(1, 0); } /* * Phase three enables interrupt sources: */ SCC_WRITE(15, zspp->wr15); SCC_WRITE0(ZSWR0_RESET_STATUS); SCC_WRITE0(ZSWR0_RESET_ERRORS); SCC_BIS(1, ZSWR1_INIT); } static void zsnull_intr(struct zscom *zs) { short c; SCC_WRITE0(ZSWR0_RESET_TXINT); SCC_WRITE0(ZSWR0_RESET_STATUS); c = SCC_READDATA(); ZSDELAY(); #ifdef lint c = c; #endif /* lint */ SCC_WRITE0(ZSWR0_RESET_ERRORS); } static int zsnull_softint(struct zscom *zs) { cmn_err(CE_WARN, "zs%d: unexpected soft int\n", zs->zs_unit); return (0); } /* * These will be called on suspend/resume for un-opened zs ports. */ static int zsnull_suspend(struct zscom *zs) { struct zs_prog *zspp = &zs_prog[zs->zs_unit]; /* * Get a copy of the current registers */ mutex_enter(zs->zs_excl); mutex_enter(zs->zs_excl_hi); zspp->zs = zs; zspp->flags = 0; zspp->wr3 = zs->zs_wreg[3]; zspp->wr4 = zs->zs_wreg[4]; zspp->wr5 = zs->zs_wreg[5]; zspp->wr11 = zs->zs_wreg[11]; zspp->wr12 = zs->zs_wreg[12]; zspp->wr13 = zs->zs_wreg[13]; zspp->wr15 = zs->zs_wreg[15]; mutex_exit(zs->zs_excl_hi); mutex_exit(zs->zs_excl); return (DDI_SUCCESS); } static int zsnull_resume(struct zscom *zs) { struct zs_prog *zspp = &zs_prog[zs->zs_unit]; /* * Restore registers */ mutex_enter(zs->zs_excl); mutex_enter(zs->zs_excl_hi); zs_program(zspp); SCC_WRITE(9, ZSWR9_MASTER_IE); DELAY(4000); mutex_exit(zs->zs_excl_hi); mutex_exit(zs->zs_excl); return (DDI_SUCCESS); }