/* * Copyright (c) 2014 Martin Pieuchot. All rights reserved. * Copyright (c) 2010 Hans Petter Selasky. All rights reserved. * Copyright 2016 Joyent, Inc. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #ifndef _SYS_USB_HCD_XHCI_XHCIREG_H #define _SYS_USB_HCD_XHCI_XHCIREG_H /* * xHCI Register and Field Definitions */ #ifdef __cplusplus extern "C" { #endif /* * xHCI PCI config registers */ #define PCI_XHCI_CBMEM 0x10 /* configuration base MEM */ #define PCI_XHCI_USBREV 0x60 /* RO USB protocol revision */ #define PCI_USB_REV_3_0 0x30 /* USB 3.0 */ #define PCI_XHCI_FLADJ 0x61 /* RW frame length adjust */ #define PCI_XHCI_INTEL_XUSB2PR 0xD0 /* Intel USB2 Port Routing */ #define PCI_XHCI_INTEL_USB2PRM 0xD4 /* Intel USB2 Port Routing Mask */ #define PCI_XHCI_INTEL_USB3_PSSEN 0xD8 /* Intel USB3 Port SuperSpeed Enable */ #define PCI_XHCI_INTEL_USB3PRM 0xDC /* Intel USB3 Port Routing Mask */ /* * xHCI capability registers */ #define XHCI_CAPLENGTH 0x00 /* RO capability */ #define XHCI_RESERVED 0x01 /* Reserved */ #define XHCI_HCIVERSION 0x02 /* RO Interface version number */ #define XHCI_HCIVERSION_0_9 0x0090 /* xHCI version 0.9 */ #define XHCI_HCIVERSION_1_0 0x0100 /* xHCI version 1.0 */ /* * Structural Parameters 1 - xHCI 1.1 / 5.3.3 */ #define XHCI_HCSPARAMS1 0x04 #define XHCI_HCS1_DEVSLOT_MAX(x) ((x) & 0xFF) #define XHCI_HCS1_IRQ_MAX(x) (((x) >> 8) & 0x3FF) #define XHCI_HCS1_N_PORTS(x) (((x) >> 24) & 0xFF) /* * Structural Parameters 2 - xHCI 1.1 / 5.3.4 */ #define XHCI_HCSPARAMS2 0x08 #define XHCI_HCS2_IST(x) ((x) & 0x7) #define XHCI_HCS2_IST_MICRO(x) (!((x) & 0x8)) #define XHCI_HCS2_ERST_MAX(x) (((x) >> 4) & 0xF) #define XHCI_HCS2_SPR(x) (((x) >> 24) & 0x1) #define XHCI_HCS2_SPB_MAX(x) ((((x) >> 16) & 0x3e0) | (((x) >> 27) & 0x1f)) /* * Structural Parameters 3 - xHCI 1.1 / 5.3.5 */ #define XHCI_HCSPARAMS3 0x0C #define XHCI_HCS3_U1_DEL(x) ((x) & 0xFF) #define XHCI_HCS3_U2_DEL(x) (((x) >> 16) & 0xFFFF) /* * Capability Parameters 1 - xHCI 1.1 / 5.3.6 */ #define XHCI_HCCPARAMS1 0x10 #define XHCI_HCC1_FLAGS_MASK(x) ((x) & 0x7FF) #define XHCI_HCC1_PSA_SZ_MAX(x) (((x) >> 12) & 0xF) #define XHCI_HCC1_XECP(x) (((x) >> 16) & 0xFFFF) /* * Capability Parameters 1 - xHCI 1.1 / 5.3.9 */ #define XHCI_HCCPARAMS2 0x1C #define XHCI_HCC2_FLAGS_MASK(x) ((x) & 0x3F) #define XHCI_DBOFF 0x14 /* RO doorbell offset */ #define XHCI_RTSOFF 0x18 /* RO runtime register space offset */ /* * xHCI operational registers. * Offset given by XHCI_CAPLENGTH register */ #define XHCI_USBCMD 0x00 /* XHCI command */ #define XHCI_CMD_RS 0x00000001 /* RW Run/Stop */ #define XHCI_CMD_HCRST 0x00000002 /* RW HC Reset */ #define XHCI_CMD_INTE 0x00000004 /* RW Interrupter Enable */ #define XHCI_CMD_HSEE 0x00000008 /* RW System Error Enable */ #define XHCI_CMD_LHCRST 0x00000080 /* RW Light HC Reset */ #define XHCI_CMD_CSS 0x00000100 /* RW Controller Save */ #define XHCI_CMD_CRS 0x00000200 /* RW Controller Restore */ #define XHCI_CMD_EWE 0x00000400 /* RW Enable Wrap Event */ #define XHCI_CMD_EU3S 0x00000800 /* RW Enable U3 MFINDEX Stop */ #define XHCI_USBSTS 0x04 /* XHCI status */ #define XHCI_STS_HCH 0x00000001 /* RO - HC Halted */ #define XHCI_STS_HSE 0x00000004 /* RW - Host System Error */ #define XHCI_STS_EINT 0x00000008 /* RW - Event Interrupt */ #define XHCI_STS_PCD 0x00000010 /* RW - Port Change Detect */ #define XHCI_STS_SSS 0x00000100 /* RO - Save State Status */ #define XHCI_STS_RSS 0x00000200 /* RO - Restore State Status */ #define XHCI_STS_SRE 0x00000400 /* RW - Save/Restore Error */ #define XHCI_STS_CNR 0x00000800 /* RO - Controller Not Ready */ #define XHCI_STS_HCE 0x00001000 /* RO - HC Error */ #define XHCI_PAGESIZE 0x08 /* XHCI page size mask */ #define XHCI_PAGESIZE_4K 0x00000001 /* 4K Page Size */ #define XHCI_PAGESIZE_8K 0x00000002 /* 8K Page Size */ #define XHCI_PAGESIZE_16K 0x00000004 /* 16K Page Size */ #define XHCI_PAGESIZE_32K 0x00000008 /* 32K Page Size */ #define XHCI_PAGESIZE_64K 0x00000010 /* 64K Page Size */ #define XHCI_DNCTRL 0x14 /* XHCI device notification control */ #define XHCI_DNCTRL_MASK(n) (1U << (n)) #define XHCI_CRCR 0x18 /* XHCI command ring control */ #define XHCI_CRCR_RCS 0x00000001 /* RW - consumer cycle state */ #define XHCI_CRCR_CS 0x00000002 /* RW - command stop */ #define XHCI_CRCR_CA 0x00000004 /* RW - command abort */ #define XHCI_CRCR_CRR 0x00000008 /* RW - command ring running */ #define XHCI_CRCR_MASK 0x0000000F /* * Device context base address pointer register. */ #define XHCI_DCBAAP 0x30 #define XHCI_CONFIG 0x38 #define XHCI_CONFIG_SLOTS_MASK 0x000000FF /* * xHCI Port Status Registers and bits. See xHCI 1.1 / 5.4.8. */ #define XHCI_PORTSC(n) (0x3F0 + (0x10 * (n))) /* XHCI port status */ #define XHCI_PS_CCS 0x00000001 /* RO - current connect status */ #define XHCI_PS_PED 0x00000002 /* RW - port enabled / disabled */ #define XHCI_PS_OCA 0x00000008 /* RO - over current active */ #define XHCI_PS_PR 0x00000010 /* RW - port reset */ #define XHCI_PS_PLS_GET(x) (((x) >> 5) & 0xF) /* RW - port link state */ #define XHCI_PS_PLS_SET(x) (((x) & 0xF) << 5) /* RW - port link state */ #define XHCI_PS_PP 0x00000200 /* RW - port power */ #define XHCI_PS_SPEED_GET(x) (((x) >> 10) & 0xF) /* RO - port speed */ #define XHCI_PS_PIC_GET(x) (((x) >> 14) & 0x3) /* RW - port indicator */ #define XHCI_PS_PIC_SET(x) (((x) & 0x3) << 14) /* RW - port indicator */ #define XHCI_PS_LWS 0x00010000 /* RW - port link state write strobe */ #define XHCI_PS_CSC 0x00020000 /* RW - connect status change */ #define XHCI_PS_PEC 0x00040000 /* RW - port enable/disable change */ #define XHCI_PS_WRC 0x00080000 /* RW - warm port reset change */ #define XHCI_PS_OCC 0x00100000 /* RW - over-current change */ #define XHCI_PS_PRC 0x00200000 /* RW - port reset change */ #define XHCI_PS_PLC 0x00400000 /* RW - port link state change */ #define XHCI_PS_CEC 0x00800000 /* RW - config error change */ #define XHCI_PS_CAS 0x01000000 /* RO - cold attach status */ #define XHCI_PS_WCE 0x02000000 /* RW - wake on connect enable */ #define XHCI_PS_WDE 0x04000000 /* RW - wake on disconnect enable */ #define XHCI_PS_WOE 0x08000000 /* RW - wake on over-current enable */ #define XHCI_PS_DR 0x40000000 /* RO - device removable */ #define XHCI_PS_WPR 0x80000000U /* RW - warm port reset */ #define XHCI_PS_CLEAR 0x80FF01FFU /* command bits */ #define XHCI_PS_INDPORT(x) ((x) & 0xFF) #define XHCI_PS_INDVAL(x) (((x) & 0xFF00) >> 8) /* * xHCI Port Power Management and Control Register. See xHCI 1.1 / 5.4.9. */ #define XHCI_PORTPMSC(n) (0x3F4 + (0x10 * (n))) #define XHCI_PM3_U1TO_GET(x) (((x) >> 0) & 0xFF) /* RW - U1 timeout */ #define XHCI_PM3_U1TO_SET(x) (((x) & 0xFF) << 0) /* RW - U1 timeout */ #define XHCI_PM3_U2TO_GET(x) (((x) >> 8) & 0xFF) /* RW - U2 timeout */ #define XHCI_PM3_U2TO_SET(x) (((x) & 0xFF) << 8) /* RW - U2 timeout */ #define XHCI_PM3_FLA 0x00010000 /* RW - Force Link PM Accept */ #define XHCI_PM2_L1S_GET(x) (((x) >> 0) & 0x7) /* RO - L1 status */ #define XHCI_PM2_RWE 0x00000008 /* RW - remote wakup enable */ /* RW - host initiated resume durations */ #define XHCI_PM2_HIRD_GET(x) (((x) >> 4) & 0xF) #define XHCI_PM2_HIRD_SET(x) (((x) & 0xF) << 4) #define XHCI_PM2_L1SLOT_GET(x) (((x) >> 8) & 0xFF) /* RW - L1 device slot */ #define XHCI_PM2_L1SLOT_SET(x) (((x) & 0xFF) << 8) /* RW - L1 device slot */ #define XHCI_PM2_HLE 0x00010000 /* RW - hardware LPM enable */ #define XHCI_PORTLI(n) (0x3F8 + (0x10 * (n))) /* RO - port link info */ #define XHCI_PLI3_ERR_GET(x) (((x) >> 0) & 0xFFFF) /* RO - port link errs */ #define XHCI_PORTRSV(n) (0x3FC + (0x10 * (n))) /* XHCI port reserved */ /* * xHCI runtime registers - xHCI 1.1 / 5.5. * Offset given by XHCI_CAPLENGTH + XHCI_RTSOFF registers. */ #define XHCI_MFINDEX 0x0000 /* RO - microframe index */ #define XHCI_MFINDEX_GET(x) ((x) & 0x3FFF) #define XHCI_IMAN(n) (0x0020 + (0x20 * (n))) /* XHCI interrupt */ /* management */ #define XHCI_IMAN_INTR_PEND 0x00000001 /* RW - interrupt pending */ #define XHCI_IMAN_INTR_ENA 0x00000002 /* RW - interrupt enable */ /* * XHCI Interrupt moderation */ #define XHCI_IMOD(n) (0x0024 + (0x20 * (n))) /* * XHCI event ring segment table size */ #define XHCI_ERSTSZ(n) (0x0028 + (0x20 * (n))) #define XHCI_ERSTS_MASK 0xffff #define XHCI_ERSTS_SET(x) ((x) & XHCI_ERSTS_MASK) /* * XHCI event ring segment table BA */ #define XHCI_ERSTBA(n) (0x0030 + (0x20 * (n))) /* * XHCI event ring dequeue pointer */ #define XHCI_ERDP(n) (0x0038 + (0x20 * (n))) #define XHCI_ERDP_SINDEX(x) ((x) & 0x7) /* RO - dequeue segment index */ #define XHCI_ERDP_BUSY 0x00000008 /* RW - event handler busy */ /* * XHCI doorbell registers - xHCI 1.1 / 5.6. * Offset given by XHCI_CAPLENGTH + XHCI_DBOFF registers */ #define XHCI_DOORBELL(n) (0x0000 + (4 * (n))) #define XHCI_DB_TARGET_GET(x) ((x) & 0xFF) #define XHCI_DB_TARGET_SET(x) ((x) & 0xFF) #define XHCI_DB_SID_GET(x) (((x) >> 16) & 0xFFFF) #define XHCI_DB_SID_SET(x) (((x) & 0xFFFF) << 16) /* * XHCI capability IDs - xHCI 1.1 / 7 - Table 146 */ #define XHCI_ID_XECP_DONE 0x0000 #define XHCI_ID_USB_LEGACY 0x0001 #define XHCI_ID_PROTOCOLS 0x0002 #define XHCI_ID_POWER_MGMT 0x0003 #define XHCI_ID_VIRTUALIZATION 0x0004 #define XHCI_ID_MSG_IRQ 0x0005 #define XHCI_ID_USB_LOCAL_MEM 0x0006 #define XHCI_ID_DEBUG 0x000A #define XHCI_ID_EXT_MSG_IRQ 0x0011 #define XHCI_XECP_ID(x) ((x) & 0xFF) #define XHCI_XECP_NEXT(x) (((x) >> 8) & 0xFF) /* * xHCI USB Legacy Support Capability - xHCI 1.1 / 7.1. */ #define XHCI_BIOS_OWNED (1 << 16) #define XHCI_OS_OWNED (1 << 24) /* * These definitions manipulate the generation of SMIs. Note that the contents * of reserved registers are required to be preserved. In addition, Several of * the bits require you to write one to clear. */ #define XHCI_XECP_LEGCTLSTS 0x04 #define XHCI_XECP_SMI_MASK (0x7 << 1) + (0xff << 5) + (0x7UL << 17) #define XHCI_XECP_CLEAR_SMI (0x7UL << 29) /* * xHCI Supported Protocol Capability. See xHCI 1.1 / 7.2. */ #define XHCI_XECP_PROT_MAJOR(x) ((x >> 24) & 0xff) #define XHCI_XECP_PROT_MINOR(x) ((x >> 16) & 0xff) #define XHCI_XECP_PROT_PCOUNT(x) ((x >> 8) & 0xff) /* * xHCI Slot Context definitions - xHCI 1.1 / 6.2.2. */ #define XHCI_SCTX_GET_ROUTE(x) ((x) & 0xfffff) #define XHCI_SCTX_SET_ROUTE(x) ((x) & 0xfffff) #define XHCI_SCTX_GET_SPEED(x) (((x) >> 20) & 0xf) #define XHCI_SCTX_SET_SPEED(x) (((x) & 0xf) << 20) #define XHCI_SCTX_GET_MTT(x) (((x) >> 25) & 0x1) #define XHCI_SCTX_SET_MTT(x) (((x) & 0x1) << 25) #define XHCI_SCTX_GET_HUB(x) (((x) >> 26) & 0x1) #define XHCI_SCTX_SET_HUB(x) (((x) & 0x1) << 26) #define XHCI_SCTX_GET_DCI(x) (((x) >> 27) & 0x1f) #define XHCI_SCTX_SET_DCI(x) (((x) & 0x1f) << 27) #define XHCI_SCTX_DCI_MASK (0x1fUL << 27) #define XHCI_SCTX_GET_MAX_EL(x) ((x) & 0xffff) #define XHCI_SCTX_SET_MAX_EL(x) ((x) & 0xffff) #define XHCI_SCTX_GET_RHPORT(x) (((x) >> 16) & 0xff) #define XHCI_SCTX_SET_RHPORT(x) (((x) & 0xff) << 16) #define XHCI_SCTX_GET_NPORTS(x) (((x) >> 24) & 0xff) #define XHCI_SCTX_SET_NPORTS(x) (((x) & 0xff) << 24) #define XHCI_SCTX_GET_TT_HUB_SID(x) ((x) & 0xff) #define XHCI_SCTX_SET_TT_HUB_SID(x) ((x) & 0xff) #define XHCI_SCTX_GET_TT_PORT_NUM(x) (((x) >> 8) & 0xff) #define XHCI_SCTX_SET_TT_PORT_NUM(x) (((x) & 0xff) << 8) #define XHCI_SCTX_GET_TT_THINK_TIME(x) (((x) >> 16) & 0x3) #define XHCI_SCTX_SET_TT_THINK_TIME(x) (((x) & 0x3) << 16) #define XHCI_SCTX_SET_IRQ_TARGET(x) (((x) & 0x3ff) << 22) #define XHCI_SCTX_GET_IRQ_TARGET(x) (((x) >> 22) & 0x3ff) #define XHCI_SCTX_GET_DEV_ADDR(x) ((x) & 0xff) #define XHCI_SCTX_GET_SLOT_STATE(x) (((x) >> 27) & 0x1f) #define XHCI_SLOT_DIS_ENAB 0 #define XHCI_SLOT_DEFAULT 1 #define XHCI_SLOT_ADDRESSED 2 #define XHCI_SLOT_CONFIGURED 3 /* * xHCI Slot Context definitions - xHCI 1.1 / 6.2.3. */ #define XHCI_EPCTX_STATE(x) ((x) & 0x7) #define XHCI_EP_DISABLED 0x0 #define XHCI_EP_RUNNING 0x1 #define XHCI_EP_HALTED 0x2 #define XHCI_EP_STOPPED 0x3 #define XHCI_EP_ERROR 0x4 #define XHCI_EPCTX_SET_MULT(x) (((x) & 0x3) << 8) #define XHCI_EPCTX_GET_MULT(x) (((x) >> 8) & 0x3) #define XHCI_EPCTX_SET_MAXP_STREAMS(x) (((x) & 0x1F) << 10) #define XHCI_EPCTX_GET_MAXP_STREAMS(x) (((x) >> 10) & 0x1F) #define XHCI_EPCTX_SET_LSA(x) (((x) & 0x1) << 15) #define XHCI_EPCTX_GET_LSA(x) (((x) >> 15) & 0x1) #define XHCI_EPCTX_SET_IVAL(x) (((x) & 0xff) << 16) #define XHCI_EPCTX_GET_IVAL(x) (((x) >> 16) & 0xFF) #define XHCI_EPCTX_GET_MAX_ESIT_HI(x) ((((x) >> 24) & 0xFF) << 16) #define XHCI_EPCTX_SET_MAX_ESIT_HI(x) ((((x) >> 16) & 0xFF) << 24) #define XHCI_EPCTX_GET_CERR(x) (((x) >> 1) & 0x3) #define XHCI_EPCTX_SET_CERR(x) (((x) & 0x3) << 1) #define XHCI_EPCTX_SET_EPTYPE(x) (((x) & 0x7) << 3) #define XHCI_EPCTX_GET_EPTYPE(x) (((x) >> 3) & 0x7) #define XHCI_EPCTX_SET_HID(x) (((x) & 0x1) << 7) #define XHCI_EPCTX_GET_HID(x) (((x) >> 7) & 0x1) #define XHCI_EPCTX_SET_MAXB(x) (((x) & 0xff) << 8) #define XHCI_EPCTX_GET_MAXB(x) (((x) >> 8) & 0xff) #define XHCI_EPCTX_SET_MPS(x) (((x) & 0xffff) << 16) #define XHCI_EPCTX_GET_MPS(x) (((x) >> 16) & 0xffff) #define XHCI_SPEED_FULL 1 #define XHCI_SPEED_LOW 2 #define XHCI_SPEED_HIGH 3 #define XHCI_SPEED_SUPER 4 #define XHCI_EPCTX_TYPE_ISOCH_OUT (1) #define XHCI_EPCTX_TYPE_BULK_OUT (2) #define XHCI_EPCTX_TYPE_INTR_OUT (3) #define XHCI_EPCTX_TYPE_CTRL (4) #define XHCI_EPCTX_TYPE_ISOCH_IN (5) #define XHCI_EPCTX_TYPE_BULK_IN (6) #define XHCI_EPCTX_TYPE_INTR_IN (7) #define XHCI_EPCTX_AVG_TRB_LEN(x) ((x) & 0xffff) #define XHCI_EPCTX_MAX_ESIT_PAYLOAD(x) (((x) & 0xffff) << 16) #define XHCI_EPCTX_GET_MAX_ESIT_PAYLOAD(x) (((x) >> 16) & 0xffff) #define XHCI_INCTX_MASK_DCI(n) (0x1 << (n)) /* * Transfer Request Block definitions. */ #define XHCI_TRB_TYPE_MASK 0xfc00 #define XHCI_TRB_TYPE(x) (((x) & XHCI_TRB_TYPE_MASK) >> 10) #define XHCI_TRB_PORTID(x) (((x) & (0xffUL << 24)) >> 24) /* Port ID */ #define XHCI_TRB_MAXSIZE (64 * 1024) #define XHCI_TRB_GET_CODE(x) (((x) >> 24) & 0xff) /* Get TRB code */ #define XHCI_TRB_TDREM(x) (((x) & 0x1f) << 17) /* Set TD remaining len. */ #define XHCI_TRB_GET_TDREM(x) (((x) >> 17) & 0x1f) /* Get TD remaining len. */ #define XHCI_TRB_REMAIN(x) ((x) & 0xffffff) /* Remaining length */ #define XHCI_TRB_LEN(x) ((x) & 0x1ffff) /* Transfer length */ #define XHCI_TRB_INTR(x) (((x) & 0x3ff) << 22) /* Set MSI-X target */ #define XHCI_TRB_GET_INTR(x) (((x) >> 22) & 0x3ff) /* Get MSI-X target */ /* * TRB flags that are used between different different TRB types. */ #define XHCI_TRB_CYCLE (1 << 0) /* Enqueue point of xfer ring */ #define XHCI_TRB_ENT (1 << 1) /* Evaluate next TRB */ #define XHCI_TRB_LINKSEG XHCI_TRB_ENT /* Link to next segment */ #define XHCI_TRB_ISP (1 << 2) /* Interrupt on short packet */ #define XHCI_TRB_NOSNOOP (1 << 3) /* PCIe no snoop */ #define XHCI_TRB_CHAIN (1 << 4) /* Chained with next TRB */ #define XHCI_TRB_IOC (1 << 5) /* Interrupt On Completion */ #define XHCI_TRB_IDT (1 << 6) /* Immediate Data */ #define XHCI_TRB_GET_TBC(x) (((x) >> 7) & 0x3) /* Get/Set Transfer */ #define XHCI_TRB_SET_TBC(x) (((x) & 0x3) << 7) /* Burst Count */ #define XHCI_TRB_BSR (1 << 9) /* Block Set Address */ #define XHCI_TRB_DCEP (1 << 9) /* Deconfigure endpoint */ #define XHCI_TRB_TSP (1 << 9) /* Transfer State Preserve */ #define XHCI_TRB_BEI (1 << 9) /* Block Event Interrupt */ #define XHCI_TRB_DIR_IN (1 << 16) #define XHCI_TRB_TRT_OUT (2 << 16) #define XHCI_TRB_TRT_IN (3 << 16) #define XHCI_TRB_GET_CYCLE(x) ((x) & 0x1) #define XHCI_TRB_GET_ED(x) (((x) >> 2) & 0x1) #define XHCI_TRB_GET_FLAGS(x) ((x) & 0x1ff) #define XHCI_TRB_GET_TYPE(x) (((x) >> 10) & 0x3f) #define XHCI_TRB_GET_EP(x) (((x) >> 16) & 0x1f) #define XHCI_TRB_SET_EP(x) (((x) & 0x1f) << 16) #define XHCI_TRB_GET_STYPE(x) (((x) >> 16) & 0x1f) #define XHCI_TRB_SET_STYPE(x) (((x) & 0x1f) << 16) #define XHCI_TRB_GET_SLOT(x) (((x) >> 24) & 0xff) #define XHCI_TRB_SET_SLOT(x) (((x) & 0xff) << 24) /* * Isochronous specific fields. See xHCI 1.1 / 6.4.1.3. */ #define XHCI_TRB_GET_TLBPC(x) (((x) >> 16) & 0xf) #define XHCI_TRB_SET_TLBPC(x) (((x) & 0xf) << 16) #define XHCI_TRB_GET_FRAME(x) (((x) >> 20) & 0x7ff) #define XHCI_TRB_SET_FRAME(x) (((x) & 0x7ff) << 20) #define XHCI_TRB_SIA (1UL << 31) /* Start Isoch ASAP */ /* * TRB Types. See xHCI 1.1 / 6.4.6. */ /* Transfer Ring Types */ #define XHCI_TRB_TYPE_NORMAL (1 << 10) #define XHCI_TRB_TYPE_SETUP (2 << 10) #define XHCI_TRB_TYPE_DATA (3 << 10) #define XHCI_TRB_TYPE_STATUS (4 << 10) #define XHCI_TRB_TYPE_ISOCH (5 << 10) #define XHCI_TRB_TYPE_LINK (6 << 10) #define XHCI_TRB_TYPE_EVENT (7 << 10) #define XHCI_TRB_TYPE_NOOP (8 << 10) /* Command ring Types */ #define XHCI_CMD_ENABLE_SLOT (9 << 10) #define XHCI_CMD_DISABLE_SLOT (10 << 10) #define XHCI_CMD_ADDRESS_DEVICE (11 << 10) #define XHCI_CMD_CONFIG_EP (12 << 10) #define XHCI_CMD_EVAL_CTX (13 << 10) #define XHCI_CMD_RESET_EP (14 << 10) #define XHCI_CMD_STOP_EP (15 << 10) #define XHCI_CMD_SET_TR_DEQ (16 << 10) #define XHCI_CMD_RESET_DEV (17 << 10) #define XHCI_CMD_FEVENT (18 << 10) #define XHCI_CMD_NEG_BW (19 << 10) #define XHCI_CMD_SET_LT (20 << 10) #define XHCI_CMD_GET_BW (21 << 10) #define XHCI_CMD_FHEADER (22 << 10) #define XHCI_CMD_NOOP (23 << 10) /* Event ring Types */ #define XHCI_EVT_XFER (32 << 10) #define XHCI_EVT_CMD_COMPLETE (33 << 10) #define XHCI_EVT_PORT_CHANGE (34 << 10) #define XHCI_EVT_BW_REQUEST (35 << 10) #define XHCI_EVT_DOORBELL (36 << 10) #define XHCI_EVT_HOST_CTRL (37 << 10) #define XHCI_EVT_DEVICE_NOTIFY (38 << 10) #define XHCI_EVT_MFINDEX_WRAP (39 << 10) #define XHCI_RING_TYPE_SHIFT(x) ((x) << 10) /* * TRB Completion Codes. See xHCI 1.1 / 6.4.5. */ #define XHCI_CODE_INVALID 0 /* Producer didn't update the code. */ #define XHCI_CODE_SUCCESS 1 /* Badaboum, plaf, plouf, yeepee! */ #define XHCI_CODE_DATA_BUF 2 /* Overrun or underrun */ #define XHCI_CODE_BABBLE 3 /* Device is "babbling" */ #define XHCI_CODE_TXERR 4 /* USB Transaction error */ #define XHCI_CODE_TRB 5 /* Invalid TRB */ #define XHCI_CODE_STALL 6 /* Stall condition */ #define XHCI_CODE_RESOURCE 7 /* No resource available for the cmd */ #define XHCI_CODE_BANDWIDTH 8 /* Not enough bandwidth for the cmd */ #define XHCI_CODE_NO_SLOTS 9 /* MaxSlots limit reached */ #define XHCI_CODE_STREAM_TYPE 10 /* Stream Context Type value detected */ #define XHCI_CODE_SLOT_NOT_ON 11 /* Related device slot is disabled */ #define XHCI_CODE_ENDP_NOT_ON 12 /* Related enpoint is disabled */ #define XHCI_CODE_SHORT_XFER 13 /* Short packet */ #define XHCI_CODE_RING_UNDERRUN 14 /* Empty ring when transmitting isoc */ #define XHCI_CODE_RING_OVERRUN 15 /* Empty ring when receiving isoc */ #define XHCI_CODE_VF_RING_FULL 16 /* VF's event ring is full */ #define XHCI_CODE_PARAMETER 17 /* Context parameter is invalid */ #define XHCI_CODE_BW_OVERRUN 18 /* TD exceeds the bandwidth */ #define XHCI_CODE_CONTEXT_STATE 19 /* Transition from illegal ctx state */ #define XHCI_CODE_NO_PING_RESP 20 /* Unable to complete periodic xfer */ #define XHCI_CODE_EV_RING_FULL 21 /* Unable to post an evt to the ring */ #define XHCI_CODE_INCOMPAT_DEV 22 /* Device cannot be accessed */ #define XHCI_CODE_MISSED_SRV 23 /* Unable to service isoc EP in ESIT */ #define XHCI_CODE_CMD_RING_STOP 24 /* Command Stop (CS) requested */ #define XHCI_CODE_CMD_ABORTED 25 /* Command Abort (CA) operation */ #define XHCI_CODE_XFER_STOPPED 26 /* xfer terminated by a stop endpoint */ #define XHCI_CODE_XFER_STOPINV 27 /* TRB transfer length invalid */ #define XHCI_CODE_XFER_STOPSHORT 28 /* Stopped before end of TD */ #define XHCI_CODE_MELAT 29 /* Max Exit Latency too large */ #define XHCI_CODE_RESERVED 30 #define XHCI_CODE_ISOC_OVERRUN 31 /* IN data buffer < Max ESIT Payload */ #define XHCI_CODE_EVENT_LOST 32 /* Internal overrun - impl. specific */ #define XHCI_CODE_UNDEFINED 33 /* Fatal error - impl. specific */ #define XHCI_CODE_INVALID_SID 34 /* Invalid stream ID received */ #define XHCI_CODE_SEC_BW 35 /* Cannot alloc secondary BW Domain */ #define XHCI_CODE_SPLITERR 36 /* USB2 split transaction */ #ifdef __cplusplus } #endif #endif /* _SYS_USB_HCD_XHCI_XHCIREG_H */