/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright 2009 Sun Microsystems, Inc. All rights reserved. * Use is subject to license terms. */ /* * * IEEE 1284 Parallel Port Device Driver * */ #include #include #include #include #include #include #include #include #include #include #include #include /* req. by dev_ops flags MTSAFE etc. */ #include /* for modldrv */ #include /* ddi_create_minor_node S_IFCHR */ #include #include #include #include #include /* hw description */ #include /* ioctl description */ #include /* driver description */ #include #include /* * Background * ========== * IEEE 1284-1994 standard defines "a signalling method for asynchronous, * fully interlocked, bidirectional parallel communications between hosts * and printers or other peripherals." (1.1) The standard defines 5 modes * of operation - Compatibility, Nibble, Byte, ECP and EPP - which differ * in direction, bandwidth, pins assignment, DMA capability, etc. * * Negotiation is a mechanism for moving between modes. Compatibility mode * is a default mode, from which negotiations to other modes occur and * to which both host and peripheral break in case of interface errors. * Compatibility mode provides a unidirectional (forward) channel for * communicating with old pre-1284 peripherals. * * Each mode has a number of phases. [Mode, phase] pair represents the * interface state. Host initiates all transfers, though peripheral can * request backchannel transfer by asserting nErr pin. * * Ecpp driver implements an IEEE 1284-compliant host using a combination * of hardware and software. Hardware part is represented by a controller, * which is a part of the SuperIO chip. Ecpp supports the following SuperIOs: * PC82332/PC82336 (U5/U10/U60), PC97317 (U100), M1553 (Grover). * Struct ecpp_hw describes each SuperIO and is determined in ecpp_attach(). * * Negotiation is performed in software. Transfer may be performed either * in software by driving output pins for each byte (PIO method), or with * hardware assistance - SuperIO has a 16-byte FIFO, which is filled by * the driver (normally using DMA), while the chip performs the actual xfer. * PIO is used for Nibble and Compat, DMA is used for ECP and Compat modes. * * Driver currently supports the following modes: * * - Compatibility mode: byte-wide forward channel ~50KB/sec; * pp->io_mode defines PIO or DMA method of transfer; * - Nibble mode: nibble-wide (4-bit) reverse channel ~30KB/sec; * - ECP mode: byte-wide bidirectional channel (~1MB/sec); * * Theory of operation * =================== * The manner in which ecpp drives 1284 interface is that of a state machine. * State is a combination of 1284 mode {ECPP_*_MODE}, 1284 phase {ECPP_PHASE_*} * and transfer method {PIO, DMA}. State is a function of application actions * {write(2), ioctl(2)} and peripheral reaction. * * 1284 interface state is described by the following variables: * pp->current_mode -- 1284 mode used for forward transfers; * pp->backchannel -- 1284 mode used for backward transfers; * pp->curent_phase -- 1284 phase; * * Bidirectional operation in Compatibility mode is provided by a combination: * pp->current_mode == ECPP_COMPAT_MODE && pp->backchannel == ECPP_NIBBLE_MODE * ECPP_CENTRONICS means no backchannel * * Driver internal state is defined by pp->e_busy as follows: * ECPP_IDLE -- idle, no active transfers; * ECPP_BUSY -- transfer is in progress; * ECPP_ERR -- have data to transfer, but peripheral can`t receive data; * ECPP_FLUSH -- flushing the queues; * * When opened, driver is in ECPP_IDLE state, current mode is ECPP_CENTRONICS * Default negotiation tries to negotiate to the best mode supported by printer, * sets pp->current_mode and pp->backchannel accordingly. * * When output data arrives in M_DATA mblks ecpp_wput() puts them on the queue * to let ecpp_wsrv() concatenate small blocks into one big transfer * by copying them into pp->ioblock. If first the mblk data is bigger than * pp->ioblock, then it is used instead of i/o block (pointed by pp->msg) * * Before starting the transfer the driver will check if peripheral is ready * by calling ecpp_check_status() and if it is not, driver goes ECPP_ERR state * and schedules ecpp_wsrv_timer() which would qenable() the wq, effectively * rechecking the peripheral readiness and restarting itself until it is ready. * The transfer is then started by calling ecpp_start(), driver goes ECPP_BUSY * * While transfer is in progress all arriving messages will be queued up. * Transfer can end up in either of two ways: * - interrupt occurs, ecpp_isr() checks if all the data was transferred, if so * cleanup and go ECPP_IDLE, otherwise putback untransferred and qenable(); * - ecpp_xfer_timeout() cancels the transfer and puts back untransferred data; * * PIO transfer method is very CPU intensive: for each sent byte the peripheral * state is checked, then the byte is transfered and driver waits for an nAck * interrupt; ecpp_isr() will then look if there is more data and if so * triggers the soft interrupt, which transfers the next byte. PIO method * is needed only for legacy printers which are sensitive to strobe problem * (Bugid 4192788). * * ecpp_wsrv() is responsible for both starting transfers (ecpp_start()) and * going idle (ecpp_idle_phase()). Many routines qenable() the write queue, * meaning "check if there are pending requests, process them and go idle". * * In it`s idle state the driver will always try to listen to the backchannel * (as advised by 1284). * * The mechanism for handling backchannel requests is as follows: * - when the peripheral has data to send it asserts nErr pin * (and also nAck in Nibble Mode) which results in an interrupt on the host; * - ISR creates M_CTL message containing an ECPP_BACKCHANNEL byte and * puts it back on the write queue; * - ecpp_wsrv() gets M_CTL and calls ecpp_peripheral2host(), which kicks off * the transfer; * * This way Nibble and ECP mode backchannel are implemented. * If the read queue gets full, backchannel request is rejected. * As the application reads data and queue size falls below the low watermark, * ecpp_rsrv() gets called and enables the backchannel again. * * Future enhancements * =================== * * Support new modes: Byte and EPP. */ #ifndef ECPP_DEBUG #define ECPP_DEBUG 0 #endif /* ECPP_DEBUG */ int ecpp_debug = ECPP_DEBUG; int noecp = 0; /* flag not to use ECP mode */ /* driver entry point fn definitions */ static int ecpp_open(queue_t *, dev_t *, int, int, cred_t *); static int ecpp_close(queue_t *, int, cred_t *); static uint_t ecpp_isr(caddr_t); static uint_t ecpp_softintr(caddr_t); /* configuration entry point fn definitions */ static int ecpp_getinfo(dev_info_t *, ddi_info_cmd_t, void *, void **); static int ecpp_attach(dev_info_t *, ddi_attach_cmd_t); static int ecpp_detach(dev_info_t *, ddi_detach_cmd_t); static struct ecpp_hw_bind *ecpp_determine_sio_type(struct ecppunit *); /* isr support routines */ static uint_t ecpp_nErr_ihdlr(struct ecppunit *); static uint_t ecpp_pio_ihdlr(struct ecppunit *); static uint_t ecpp_dma_ihdlr(struct ecppunit *); static uint_t ecpp_M1553_intr(struct ecppunit *); /* configuration support routines */ static void ecpp_get_props(struct ecppunit *); /* Streams Routines */ static int ecpp_wput(queue_t *, mblk_t *); static int ecpp_wsrv(queue_t *); static int ecpp_rsrv(queue_t *); static void ecpp_flush(struct ecppunit *, int); static void ecpp_start(struct ecppunit *, caddr_t, size_t); /* ioctl handling */ static void ecpp_putioc(queue_t *, mblk_t *); static void ecpp_srvioc(queue_t *, mblk_t *); static void ecpp_wput_iocdata_devid(queue_t *, mblk_t *, uintptr_t); static void ecpp_putioc_copyout(queue_t *, mblk_t *, void *, int); static void ecpp_putioc_stateful_copyin(queue_t *, mblk_t *, size_t); static void ecpp_srvioc_devid(queue_t *, mblk_t *, struct ecpp_device_id *, int *); static void ecpp_srvioc_prnif(queue_t *, mblk_t *); static void ecpp_ack_ioctl(queue_t *, mblk_t *); static void ecpp_nack_ioctl(queue_t *, mblk_t *, int); /* kstat routines */ static void ecpp_kstat_init(struct ecppunit *); static int ecpp_kstat_update(kstat_t *, int); static int ecpp_kstatintr_update(kstat_t *, int); /* dma routines */ static void ecpp_putback_untransfered(struct ecppunit *, void *, uint_t); static uint8_t ecpp_setup_dma_resources(struct ecppunit *, caddr_t, size_t); static uint8_t ecpp_init_dma_xfer(struct ecppunit *, caddr_t, size_t); /* pio routines */ static void ecpp_pio_writeb(struct ecppunit *); static void ecpp_xfer_cleanup(struct ecppunit *); static uint8_t ecpp_prep_pio_xfer(struct ecppunit *, caddr_t, size_t); /* misc */ static uchar_t ecpp_reset_port_regs(struct ecppunit *); static void ecpp_xfer_timeout(void *); static void ecpp_fifo_timer(void *); static void ecpp_wsrv_timer(void *); static uchar_t dcr_write(struct ecppunit *, uint8_t); static uchar_t ecr_write(struct ecppunit *, uint8_t); static uchar_t ecpp_check_status(struct ecppunit *); static int ecpp_backchan_req(struct ecppunit *); static void ecpp_untimeout_unblock(struct ecppunit *, timeout_id_t *); static uint_t ecpp_get_prn_ifcap(struct ecppunit *); /* stubs */ static void empty_config_mode(struct ecppunit *); static void empty_mask_intr(struct ecppunit *); /* PC87332 support */ static int pc87332_map_regs(struct ecppunit *); static void pc87332_unmap_regs(struct ecppunit *); static int pc87332_config_chip(struct ecppunit *); static void pc87332_config_mode(struct ecppunit *); static uint8_t pc87332_read_config_reg(struct ecppunit *, uint8_t); static void pc87332_write_config_reg(struct ecppunit *, uint8_t, uint8_t); static void cheerio_mask_intr(struct ecppunit *); static void cheerio_unmask_intr(struct ecppunit *); static int cheerio_dma_start(struct ecppunit *); static int cheerio_dma_stop(struct ecppunit *, size_t *); static size_t cheerio_getcnt(struct ecppunit *); static void cheerio_reset_dcsr(struct ecppunit *); /* PC97317 support */ static int pc97317_map_regs(struct ecppunit *); static void pc97317_unmap_regs(struct ecppunit *); static int pc97317_config_chip(struct ecppunit *); static void pc97317_config_mode(struct ecppunit *); /* M1553 Southbridge support */ static int m1553_map_regs(struct ecppunit *pp); static void m1553_unmap_regs(struct ecppunit *pp); static int m1553_config_chip(struct ecppunit *); static uint8_t m1553_read_config_reg(struct ecppunit *, uint8_t); static void m1553_write_config_reg(struct ecppunit *, uint8_t, uint8_t); /* M1553 Southbridge DMAC 8237 support routines */ static int dma8237_dma_start(struct ecppunit *); static int dma8237_dma_stop(struct ecppunit *, size_t *); static size_t dma8237_getcnt(struct ecppunit *); static void dma8237_write_addr(struct ecppunit *, uint32_t); static void dma8237_write_count(struct ecppunit *, uint32_t); static uint32_t dma8237_read_count(struct ecppunit *); static void dma8237_write(struct ecppunit *, int, uint8_t); static uint8_t dma8237_read(struct ecppunit *, int); #ifdef INCLUDE_DMA8237_READ_ADDR static uint32_t dma8237_read_addr(struct ecppunit *); #endif /* i86 PC support rountines */ #if defined(__x86) static int x86_dma_start(struct ecppunit *); static int x86_dma_stop(struct ecppunit *, size_t *); static int x86_map_regs(struct ecppunit *); static void x86_unmap_regs(struct ecppunit *); static int x86_config_chip(struct ecppunit *); static size_t x86_getcnt(struct ecppunit *); #endif /* IEEE 1284 phase transitions */ static void ecpp_1284_init_interface(struct ecppunit *); static int ecpp_1284_termination(struct ecppunit *); static uchar_t ecpp_idle_phase(struct ecppunit *); static int ecp_forward2reverse(struct ecppunit *); static int ecp_reverse2forward(struct ecppunit *); static int read_nibble_backchan(struct ecppunit *); /* reverse transfers */ static uint_t ecpp_peripheral2host(struct ecppunit *); static uchar_t ecp_peripheral2host(struct ecppunit *); static uchar_t nibble_peripheral2host(struct ecppunit *pp, uint8_t *); static int ecpp_getdevid(struct ecppunit *, uint8_t *, int *, int); static void ecpp_ecp_read_timeout(void *); static void ecpp_ecp_read_completion(struct ecppunit *); /* IEEE 1284 mode transitions */ static void ecpp_default_negotiation(struct ecppunit *); static int ecpp_mode_negotiation(struct ecppunit *, uchar_t); static int ecpp_1284_negotiation(struct ecppunit *, uint8_t, uint8_t *); static int ecp_negotiation(struct ecppunit *); static int nibble_negotiation(struct ecppunit *); static int devidnib_negotiation(struct ecppunit *); /* IEEE 1284 utility routines */ static int wait_dsr(struct ecppunit *, uint8_t, uint8_t, int); /* debugging functions */ static void ecpp_error(dev_info_t *, char *, ...); static uchar_t ecpp_get_error_status(uchar_t); /* * Chip-dependent structures */ static ddi_dma_attr_t cheerio_dma_attr = { DMA_ATTR_VERSION, /* version */ 0x00000000ull, /* dlim_addr_lo */ 0xfffffffeull, /* dlim_addr_hi */ 0xffffff, /* DMA counter register */ 1, /* DMA address alignment */ 0x74, /* burst sizes */ 0x0001, /* min effective DMA size */ 0xffff, /* maximum transfer size */ 0xffff, /* segment boundary */ 1, /* s/g list length */ 1, /* granularity of device */ 0 /* DMA flags */ }; static struct ecpp_hw pc87332 = { pc87332_map_regs, pc87332_unmap_regs, pc87332_config_chip, pc87332_config_mode, cheerio_mask_intr, cheerio_unmask_intr, cheerio_dma_start, cheerio_dma_stop, cheerio_getcnt, &cheerio_dma_attr }; static struct ecpp_hw pc97317 = { pc97317_map_regs, pc97317_unmap_regs, pc97317_config_chip, pc97317_config_mode, cheerio_mask_intr, cheerio_unmask_intr, cheerio_dma_start, cheerio_dma_stop, cheerio_getcnt, &cheerio_dma_attr }; static ddi_dma_attr_t i8237_dma_attr = { DMA_ATTR_VERSION, /* version */ 0x00000000ull, /* dlim_addr_lo */ 0xfffffffeull, /* dlim_addr_hi */ 0xffff, /* DMA counter register */ 1, /* DMA address alignment */ 0x01, /* burst sizes */ 0x0001, /* min effective DMA size */ 0xffff, /* maximum transfer size */ 0x7fff, /* segment boundary */ 1, /* s/g list length */ 1, /* granularity of device */ 0 /* DMA flags */ }; static struct ecpp_hw m1553 = { m1553_map_regs, m1553_unmap_regs, m1553_config_chip, empty_config_mode, /* no config_mode */ empty_mask_intr, /* no mask_intr */ empty_mask_intr, /* no unmask_intr */ dma8237_dma_start, dma8237_dma_stop, dma8237_getcnt, &i8237_dma_attr }; #if defined(__x86) static ddi_dma_attr_t sb_dma_attr = { DMA_ATTR_VERSION, /* version */ 0x00000000ull, /* dlim_addr_lo */ 0xffffff, /* dlim_addr_hi */ 0xffff, /* DMA counter register */ 1, /* DMA address alignment */ 0x01, /* burst sizes */ 0x0001, /* min effective DMA size */ 0xffffffff, /* maximum transfer size */ 0xffff, /* segment boundary */ 1, /* s/g list length */ 1, /* granularity of device */ 0 /* DMA flags */ }; static struct ecpp_hw x86 = { x86_map_regs, x86_unmap_regs, x86_config_chip, empty_config_mode, /* no config_mode */ empty_mask_intr, /* no mask_intr */ empty_mask_intr, /* no unmask_intr */ x86_dma_start, x86_dma_stop, x86_getcnt, &sb_dma_attr }; #endif /* * list of supported devices */ struct ecpp_hw_bind ecpp_hw_bind[] = { { "ns87317-ecpp", &pc97317, "PC97317" }, { "pnpALI,1533,3", &m1553, "M1553" }, { "ecpp", &pc87332, "PC87332" }, #if defined(__x86) { "lp", &x86, "i86pc"}, #endif }; static ddi_device_acc_attr_t acc_attr = { DDI_DEVICE_ATTR_V0, DDI_STRUCTURE_LE_ACC, DDI_STRICTORDER_ACC }; static struct ecpp_transfer_parms default_xfer_parms = { FWD_TIMEOUT_DEFAULT, /* write timeout in seconds */ ECPP_CENTRONICS /* supported mode */ }; /* prnio interface info string */ static const char prn_ifinfo[] = PRN_PARALLEL; /* prnio timeouts */ static const struct prn_timeouts prn_timeouts_default = { FWD_TIMEOUT_DEFAULT, /* forward timeout */ REV_TIMEOUT_DEFAULT /* reverse timeout */ }; static int ecpp_isr_max_delay = ECPP_ISR_MAX_DELAY; static int ecpp_def_timeout = 90; /* left in for 2.7 compatibility */ static void *ecppsoft_statep; /* * STREAMS framework manages locks for these structures */ _NOTE(SCHEME_PROTECTS_DATA("unique per call", iocblk)) _NOTE(SCHEME_PROTECTS_DATA("unique per call", datab)) _NOTE(SCHEME_PROTECTS_DATA("unique per call", msgb)) _NOTE(SCHEME_PROTECTS_DATA("unique per call", queue)) _NOTE(SCHEME_PROTECTS_DATA("unique per call", copyreq)) _NOTE(SCHEME_PROTECTS_DATA("unique per call", stroptions)) struct module_info ecppinfo = { /* id, name, min pkt siz, max pkt siz, hi water, low water */ 42, "ecpp", 0, IO_BLOCK_SZ, ECPPHIWAT, ECPPLOWAT }; static struct qinit ecpp_rinit = { putq, ecpp_rsrv, ecpp_open, ecpp_close, NULL, &ecppinfo, NULL }; static struct qinit ecpp_wint = { ecpp_wput, ecpp_wsrv, ecpp_open, ecpp_close, NULL, &ecppinfo, NULL }; struct streamtab ecpp_str_info = { &ecpp_rinit, &ecpp_wint, NULL, NULL }; static struct cb_ops ecpp_cb_ops = { nodev, /* cb_open */ nodev, /* cb_close */ nodev, /* cb_strategy */ nodev, /* cb_print */ nodev, /* cb_dump */ nodev, /* cb_read */ nodev, /* cb_write */ nodev, /* cb_ioctl */ nodev, /* cb_devmap */ nodev, /* cb_mmap */ nodev, /* cb_segmap */ nochpoll, /* cb_chpoll */ ddi_prop_op, /* cb_prop_op */ &ecpp_str_info, /* cb_stream */ (D_NEW | D_MP | D_MTPERQ) /* cb_flag */ }; /* * Declare ops vectors for auto configuration. */ struct dev_ops ecpp_ops = { DEVO_REV, /* devo_rev */ 0, /* devo_refcnt */ ecpp_getinfo, /* devo_getinfo */ nulldev, /* devo_identify */ nulldev, /* devo_probe */ ecpp_attach, /* devo_attach */ ecpp_detach, /* devo_detach */ nodev, /* devo_reset */ &ecpp_cb_ops, /* devo_cb_ops */ (struct bus_ops *)NULL, /* devo_bus_ops */ nulldev, /* devo_power */ ddi_quiesce_not_needed, /* devo_quiesce */ }; extern struct mod_ops mod_driverops; static struct modldrv ecppmodldrv = { &mod_driverops, /* type of module - driver */ "parallel port driver", &ecpp_ops, }; static struct modlinkage ecppmodlinkage = { MODREV_1, &ecppmodldrv, 0 }; /* * * DDI/DKI entry points and supplementary routines * */ int _init(void) { int error; if ((error = mod_install(&ecppmodlinkage)) == 0) { (void) ddi_soft_state_init(&ecppsoft_statep, sizeof (struct ecppunit), 1); } return (error); } int _fini(void) { int error; if ((error = mod_remove(&ecppmodlinkage)) == 0) { ddi_soft_state_fini(&ecppsoft_statep); } return (error); } int _info(struct modinfo *modinfop) { return (mod_info(&ecppmodlinkage, modinfop)); } static int ecpp_attach(dev_info_t *dip, ddi_attach_cmd_t cmd) { int instance; char name[16]; struct ecppunit *pp; struct ecpp_hw_bind *hw_bind; instance = ddi_get_instance(dip); switch (cmd) { case DDI_ATTACH: break; case DDI_RESUME: if (!(pp = ddi_get_soft_state(ecppsoft_statep, instance))) { return (DDI_FAILURE); } mutex_enter(&pp->umutex); pp->suspended = FALSE; /* * Initialize the chip and restore current mode if needed */ (void) ECPP_CONFIG_CHIP(pp); (void) ecpp_reset_port_regs(pp); if (pp->oflag == TRUE) { int current_mode = pp->current_mode; (void) ecpp_1284_termination(pp); (void) ecpp_mode_negotiation(pp, current_mode); } mutex_exit(&pp->umutex); return (DDI_SUCCESS); default: return (DDI_FAILURE); } if (ddi_soft_state_zalloc(ecppsoft_statep, instance) != 0) { ecpp_error(dip, "ddi_soft_state_zalloc failed\n"); goto fail; } pp = ddi_get_soft_state(ecppsoft_statep, instance); pp->dip = dip; pp->suspended = FALSE; /* * Determine SuperIO type and set chip-dependent variables */ hw_bind = ecpp_determine_sio_type(pp); if (hw_bind == NULL) { cmn_err(CE_NOTE, "parallel port controller not supported"); goto fail_sio; } else { pp->hw = hw_bind->hw; ecpp_error(pp->dip, "SuperIO type: %s\n", hw_bind->info); } /* * Map registers */ if (ECPP_MAP_REGS(pp) != SUCCESS) { goto fail_map; } if (ddi_dma_alloc_handle(dip, pp->hw->attr, DDI_DMA_DONTWAIT, NULL, &pp->dma_handle) != DDI_SUCCESS) { ecpp_error(dip, "ecpp_attach: failed ddi_dma_alloc_handle\n"); goto fail_dma; } if (ddi_get_iblock_cookie(dip, 0, &pp->ecpp_trap_cookie) != DDI_SUCCESS) { ecpp_error(dip, "ecpp_attach: failed ddi_get_iblock_cookie\n"); goto fail_ibc; } mutex_init(&pp->umutex, NULL, MUTEX_DRIVER, (void *)pp->ecpp_trap_cookie); cv_init(&pp->pport_cv, NULL, CV_DRIVER, NULL); if (ddi_add_intr(dip, 0, &pp->ecpp_trap_cookie, NULL, ecpp_isr, (caddr_t)pp) != DDI_SUCCESS) { ecpp_error(dip, "ecpp_attach: failed to add hard intr\n"); goto fail_intr; } if (ddi_add_softintr(dip, DDI_SOFTINT_LOW, &pp->softintr_id, 0, 0, ecpp_softintr, (caddr_t)pp) != DDI_SUCCESS) { ecpp_error(dip, "ecpp_attach: failed to add soft intr\n"); goto fail_softintr; } (void) sprintf(name, "ecpp%d", instance); if (ddi_create_minor_node(dip, name, S_IFCHR, instance, DDI_NT_PRINTER, 0) == DDI_FAILURE) { ecpp_error(dip, "ecpp_attach: create_minor_node failed\n"); goto fail_minor; } pp->ioblock = (caddr_t)kmem_alloc(IO_BLOCK_SZ, KM_SLEEP); if (pp->ioblock == NULL) { ecpp_error(dip, "ecpp_attach: kmem_alloc failed\n"); goto fail_iob; } else { ecpp_error(pp->dip, "ecpp_attach: ioblock=0x%x\n", pp->ioblock); } ecpp_get_props(pp); #if defined(__x86) if (pp->hw == &x86 && pp->uh.x86.chn != 0xff) { if (ddi_dmae_alloc(dip, pp->uh.x86.chn, DDI_DMA_DONTWAIT, NULL) == DDI_SUCCESS) ecpp_error(pp->dip, "dmae_alloc success!\n"); } #endif if (ECPP_CONFIG_CHIP(pp) == FAILURE) { ecpp_error(pp->dip, "config_chip failed.\n"); goto fail_config; } ecpp_kstat_init(pp); ddi_report_dev(dip); return (DDI_SUCCESS); fail_config: ddi_prop_remove_all(dip); kmem_free(pp->ioblock, IO_BLOCK_SZ); fail_iob: ddi_remove_minor_node(dip, NULL); fail_minor: ddi_remove_softintr(pp->softintr_id); fail_softintr: ddi_remove_intr(dip, (uint_t)0, pp->ecpp_trap_cookie); fail_intr: mutex_destroy(&pp->umutex); cv_destroy(&pp->pport_cv); fail_ibc: ddi_dma_free_handle(&pp->dma_handle); fail_dma: ECPP_UNMAP_REGS(pp); fail_map: fail_sio: ddi_soft_state_free(ecppsoft_statep, instance); fail: ecpp_error(dip, "ecpp_attach: failed.\n"); return (DDI_FAILURE); } static int ecpp_detach(dev_info_t *dip, ddi_detach_cmd_t cmd) { int instance; struct ecppunit *pp; instance = ddi_get_instance(dip); switch (cmd) { case DDI_DETACH: break; case DDI_SUSPEND: if (!(pp = ddi_get_soft_state(ecppsoft_statep, instance))) { return (DDI_FAILURE); } mutex_enter(&pp->umutex); ASSERT(pp->suspended == FALSE); pp->suspended = TRUE; /* prevent new transfers */ /* * Wait if there's any activity on the port */ if ((pp->e_busy == ECPP_BUSY) || (pp->e_busy == ECPP_FLUSH)) { (void) cv_reltimedwait(&pp->pport_cv, &pp->umutex, SUSPEND_TOUT * drv_usectohz(1000000), TR_CLOCK_TICK); if ((pp->e_busy == ECPP_BUSY) || (pp->e_busy == ECPP_FLUSH)) { pp->suspended = FALSE; mutex_exit(&pp->umutex); ecpp_error(pp->dip, "ecpp_detach: suspend timeout\n"); return (DDI_FAILURE); } } mutex_exit(&pp->umutex); return (DDI_SUCCESS); default: return (DDI_FAILURE); } pp = ddi_get_soft_state(ecppsoft_statep, instance); #if defined(__x86) if (pp->hw == &x86 && pp->uh.x86.chn != 0xff) (void) ddi_dmae_release(pp->dip, pp->uh.x86.chn); #endif if (pp->dma_handle != NULL) ddi_dma_free_handle(&pp->dma_handle); ddi_remove_minor_node(dip, NULL); ddi_remove_softintr(pp->softintr_id); ddi_remove_intr(dip, (uint_t)0, pp->ecpp_trap_cookie); if (pp->ksp) { kstat_delete(pp->ksp); } if (pp->intrstats) { kstat_delete(pp->intrstats); } cv_destroy(&pp->pport_cv); mutex_destroy(&pp->umutex); ECPP_UNMAP_REGS(pp); kmem_free(pp->ioblock, IO_BLOCK_SZ); ddi_prop_remove_all(dip); ddi_soft_state_free(ecppsoft_statep, instance); return (DDI_SUCCESS); } /* * ecpp_get_props() reads ecpp.conf for user defineable tuneables. * If the file or a particular variable is not there, a default value * is assigned. */ static void ecpp_get_props(struct ecppunit *pp) { char *prop; #if defined(__x86) int len; int value; #endif /* * If fast_centronics is TRUE, non-compliant IEEE 1284 * peripherals ( Centronics peripherals) will operate in DMA mode. * Transfers betwee main memory and the device will be via DMA; * peripheral handshaking will be conducted by superio logic. * If ecpp can not read the variable correctly fast_centronics will * be set to FALSE. In this case, transfers and handshaking * will be conducted by PIO for Centronics devices. */ if (ddi_prop_lookup_string(DDI_DEV_T_ANY, pp->dip, 0, "fast-centronics", &prop) == DDI_PROP_SUCCESS) { pp->fast_centronics = (strcmp(prop, "true") == 0) ? TRUE : FALSE; ddi_prop_free(prop); } else { pp->fast_centronics = FALSE; } /* * If fast-1284-compatible is set to TRUE, when ecpp communicates * with IEEE 1284 compliant peripherals, data transfers between * main memory and the parallel port will be conducted by DMA. * Handshaking between the port and peripheral will be conducted * by superio logic. This is the default characteristic. If * fast-1284-compatible is set to FALSE, transfers and handshaking * will be conducted by PIO. */ if (ddi_prop_lookup_string(DDI_DEV_T_ANY, pp->dip, 0, "fast-1284-compatible", &prop) == DDI_PROP_SUCCESS) { pp->fast_compat = (strcmp(prop, "true") == 0) ? TRUE : FALSE; ddi_prop_free(prop); } else { pp->fast_compat = TRUE; } /* * Some centronics peripherals require the nInit signal to be * toggled to reset the device. If centronics_init_seq is set * to TRUE, ecpp will toggle the nInit signal upon every ecpp_open(). * Applications have the opportunity to toggle the nInit signal * with ioctl(2) calls as well. The default is to set it to FALSE. */ if (ddi_prop_lookup_string(DDI_DEV_T_ANY, pp->dip, 0, "centronics-init-seq", &prop) == DDI_PROP_SUCCESS) { pp->init_seq = (strcmp(prop, "true") == 0) ? TRUE : FALSE; ddi_prop_free(prop); } else { pp->init_seq = FALSE; } /* * If one of the centronics status signals are in an erroneous * state, ecpp_wsrv() will be reinvoked centronics-retry ms to * check if the status is ok to transfer. If the property is not * found, wsrv_retry will be set to CENTRONICS_RETRY ms. */ pp->wsrv_retry = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "centronics-retry", CENTRONICS_RETRY); /* * In PIO mode, ecpp_isr() will loop for wait for the busy signal * to be deasserted before transferring the next byte. wait_for_busy * is specificied in microseconds. If the property is not found * ecpp_isr() will wait for a maximum of WAIT_FOR_BUSY us. */ pp->wait_for_busy = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "centronics-wait-for-busy", WAIT_FOR_BUSY); /* * In PIO mode, centronics transfers must hold the data signals * for a data_setup_time milliseconds before the strobe is asserted. */ pp->data_setup_time = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "centronics-data-setup-time", DATA_SETUP_TIME); /* * In PIO mode, centronics transfers asserts the strobe signal * for a period of strobe_pulse_width milliseconds. */ pp->strobe_pulse_width = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "centronics-strobe-pulse-width", STROBE_PULSE_WIDTH); /* * Upon a transfer the peripheral, ecpp waits write_timeout seconds * for the transmission to complete. */ default_xfer_parms.write_timeout = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "ecpp-transfer-timeout", ecpp_def_timeout); pp->xfer_parms = default_xfer_parms; /* * Get dma channel for M1553 */ if (pp->hw == &m1553) { pp->uh.m1553.chn = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "dma-channel", 0x1); ecpp_error(pp->dip, "ecpp_get_prop:chn=%x\n", pp->uh.m1553.chn); } #if defined(__x86) len = sizeof (value); /* Get dma channel for i86 pc */ if (pp->hw == &x86) { if (ddi_prop_op(DDI_DEV_T_ANY, pp->dip, PROP_LEN_AND_VAL_BUF, DDI_PROP_DONTPASS, "dma-channels", (caddr_t)&value, &len) != DDI_PROP_SUCCESS) { ecpp_error(pp->dip, "No dma channel found\n"); pp->uh.x86.chn = 0xff; pp->fast_compat = FALSE; pp->noecpregs = TRUE; } else pp->uh.x86.chn = (uint8_t)value; } #endif /* * these properties are not yet public */ pp->ecp_rev_speed = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "ecp-rev-speed", ECP_REV_SPEED); pp->rev_watchdog = ddi_prop_get_int(DDI_DEV_T_ANY, pp->dip, 0, "rev-watchdog", REV_WATCHDOG); ecpp_error(pp->dip, "ecpp_get_prop: fast_centronics=%x, fast-1284=%x\n" "ecpp_get_prop: wsrv_retry=%d, wait_for_busy=%d\n" "ecpp_get_prop: data_setup=%d, strobe_pulse=%d\n" "ecpp_get_prop: transfer-timeout=%d\n", pp->fast_centronics, pp->fast_compat, pp->wsrv_retry, pp->wait_for_busy, pp->data_setup_time, pp->strobe_pulse_width, pp->xfer_parms.write_timeout); } /*ARGSUSED*/ int ecpp_getinfo(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, void **result) { dev_t dev = (dev_t)arg; struct ecppunit *pp; int instance, ret; instance = getminor(dev); switch (infocmd) { case DDI_INFO_DEVT2DEVINFO: pp = ddi_get_soft_state(ecppsoft_statep, instance); if (pp != NULL) { *result = pp->dip; ret = DDI_SUCCESS; } else { ret = DDI_FAILURE; } break; case DDI_INFO_DEVT2INSTANCE: *result = (void *)(uintptr_t)instance; ret = DDI_SUCCESS; break; default: ret = DDI_FAILURE; break; } return (ret); } /*ARGSUSED2*/ static int ecpp_open(queue_t *q, dev_t *dev, int flag, int sflag, cred_t *credp) { struct ecppunit *pp; int instance; struct stroptions *sop; mblk_t *mop; instance = getminor(*dev); if (instance < 0) { return (ENXIO); } pp = (struct ecppunit *)ddi_get_soft_state(ecppsoft_statep, instance); if (pp == NULL) { return (ENXIO); } mutex_enter(&pp->umutex); /* * Parallel port is an exclusive-use device * thus providing print job integrity */ if (pp->oflag == TRUE) { ecpp_error(pp->dip, "ecpp open failed"); mutex_exit(&pp->umutex); return (EBUSY); } pp->oflag = TRUE; /* initialize state variables */ pp->prn_timeouts = prn_timeouts_default; pp->xfer_parms = default_xfer_parms; pp->current_mode = ECPP_CENTRONICS; pp->backchannel = ECPP_CENTRONICS; pp->current_phase = ECPP_PHASE_PO; pp->port = ECPP_PORT_DMA; pp->instance = instance; pp->timeout_error = 0; pp->saved_dsr = DSR_READ(pp); pp->ecpp_drain_counter = 0; pp->dma_cancelled = FALSE; pp->io_mode = ECPP_DMA; pp->joblen = 0; pp->tfifo_intr = 0; pp->softintr_pending = 0; pp->nread = 0; /* clear the state flag */ pp->e_busy = ECPP_IDLE; pp->readq = RD(q); pp->writeq = WR(q); pp->msg = NULL; RD(q)->q_ptr = WR(q)->q_ptr = (caddr_t)pp; /* * Get ready: check host/peripheral, negotiate into default mode */ if (ecpp_reset_port_regs(pp) == FAILURE) { mutex_exit(&pp->umutex); return (EIO); } mutex_exit(&pp->umutex); /* * Configure the Stream head and enable the Stream */ if (!(mop = allocb(sizeof (struct stroptions), BPRI_MED))) { return (EAGAIN); } mop->b_datap->db_type = M_SETOPTS; mop->b_wptr += sizeof (struct stroptions); /* * if device is open with O_NONBLOCK flag set, let read(2) return 0 * if no data waiting to be read. Writes will block on flow control. */ sop = (struct stroptions *)mop->b_rptr; sop->so_flags = SO_HIWAT | SO_LOWAT | SO_NDELON | SO_MREADON; sop->so_hiwat = ECPPHIWAT; sop->so_lowat = ECPPLOWAT; /* enable the stream */ qprocson(q); putnext(q, mop); mutex_enter(&pp->umutex); ecpp_default_negotiation(pp); /* go revidle */ (void) ecpp_idle_phase(pp); ecpp_error(pp->dip, "ecpp_open: mode=%x, phase=%x ecr=%x, dsr=%x, dcr=%x\n", pp->current_mode, pp->current_phase, ECR_READ(pp), DSR_READ(pp), DCR_READ(pp)); mutex_exit(&pp->umutex); return (0); } /*ARGSUSED1*/ static int ecpp_close(queue_t *q, int flag, cred_t *cred_p) { struct ecppunit *pp; timeout_id_t timeout_id, fifo_timer_id, wsrv_timer_id; pp = (struct ecppunit *)q->q_ptr; ecpp_error(pp->dip, "ecpp_close: entering ...\n"); mutex_enter(&pp->umutex); /* * ecpp_close() will continue to loop until the * queue has been drained or if the thread * has received a SIG. Typically, when the queue * has data, the port will be ECPP_BUSY. However, * after a dma completes and before the wsrv * starts the next transfer, the port may be IDLE. * In this case, ecpp_close() will loop within this * while(qsize) segment. Since, ecpp_wsrv() runs * at software interupt level, this shouldn't loop * very long. */ while (pp->e_busy != ECPP_IDLE || qsize(WR(q))) { if (!cv_wait_sig(&pp->pport_cv, &pp->umutex)) { ecpp_error(pp->dip, "ecpp_close:B: received SIG\n"); /* * Returning from a signal such as * SIGTERM or SIGKILL */ ecpp_flush(pp, FWRITE); break; } else { ecpp_error(pp->dip, "ecpp_close:rcvd cv-sig\n"); } } ecpp_error(pp->dip, "ecpp_close: joblen=%d, ctx_cf=%d, " "qsize(WR(q))=%d, qsize(RD(q))=%d\n", pp->joblen, pp->ctx_cf, qsize(pp->writeq), qsize(q)); /* * Cancel all timeouts, disable interrupts * * Note that we can`t call untimeout(9F) with mutex held: * callout may be blocked on the same mutex, and untimeout() will * cv_wait() while callout is executing, thus creating a deadlock * So we zero the timeout id's inside mutex and call untimeout later */ timeout_id = pp->timeout_id; fifo_timer_id = pp->fifo_timer_id; wsrv_timer_id = pp->wsrv_timer_id; pp->timeout_id = pp->fifo_timer_id = pp->wsrv_timer_id = 0; pp->softintr_pending = 0; pp->dma_cancelled = TRUE; ECPP_MASK_INTR(pp); mutex_exit(&pp->umutex); qprocsoff(q); if (timeout_id) { (void) untimeout(timeout_id); } if (fifo_timer_id) { (void) untimeout(fifo_timer_id); } if (wsrv_timer_id) { (void) untimeout(wsrv_timer_id); } mutex_enter(&pp->umutex); /* set link to Compatible mode */ if ((pp->current_mode == ECPP_ECP_MODE) && (pp->current_phase != ECPP_PHASE_ECP_FWD_IDLE)) { (void) ecp_reverse2forward(pp); } (void) ecpp_1284_termination(pp); pp->oflag = FALSE; q->q_ptr = WR(q)->q_ptr = NULL; pp->readq = pp->writeq = NULL; pp->msg = NULL; ecpp_error(pp->dip, "ecpp_close: ecr=%x, dsr=%x, dcr=%x\n", ECR_READ(pp), DSR_READ(pp), DCR_READ(pp)); mutex_exit(&pp->umutex); return (0); } /* * standard put procedure for ecpp */ static int ecpp_wput(queue_t *q, mblk_t *mp) { struct msgb *nmp; struct ecppunit *pp; pp = (struct ecppunit *)q->q_ptr; if (!mp) { return (0); } if ((mp->b_wptr - mp->b_rptr) <= 0) { ecpp_error(pp->dip, "ecpp_wput:bogus packet recieved mp=%x\n", mp); freemsg(mp); return (0); } switch (DB_TYPE(mp)) { case M_DATA: /* * This is a quick fix for multiple message block problem, * it will be changed later with better performance code. */ if (mp->b_cont) { /* * mblk has scattered data ... do msgpullup * if it fails, continue with the current mblk */ if ((nmp = msgpullup(mp, -1)) != NULL) { freemsg(mp); mp = nmp; ecpp_error(pp->dip, "ecpp_wput:msgpullup: mp=%p len=%d\n", mp, mp->b_wptr - mp->b_rptr); } } /* let ecpp_wsrv() concatenate small blocks */ (void) putq(q, mp); break; case M_CTL: (void) putq(q, mp); break; case M_IOCTL: { struct iocblk *iocbp; iocbp = (struct iocblk *)mp->b_rptr; ecpp_error(pp->dip, "ecpp_wput:M_IOCTL %x\n", iocbp->ioc_cmd); mutex_enter(&pp->umutex); /* TESTIO and GET_STATUS can be used during transfer */ if ((pp->e_busy == ECPP_BUSY) && (iocbp->ioc_cmd != BPPIOC_TESTIO) && (iocbp->ioc_cmd != PRNIOC_GET_STATUS)) { mutex_exit(&pp->umutex); (void) putq(q, mp); } else { mutex_exit(&pp->umutex); ecpp_putioc(q, mp); } break; } case M_IOCDATA: { struct copyresp *csp; ecpp_error(pp->dip, "ecpp_wput:M_IOCDATA\n"); csp = (struct copyresp *)mp->b_rptr; /* * If copy request failed, quit now */ if (csp->cp_rval != 0) { freemsg(mp); return (0); } switch (csp->cp_cmd) { case ECPPIOC_SETPARMS: case ECPPIOC_SETREGS: case ECPPIOC_SETPORT: case ECPPIOC_SETDATA: case PRNIOC_SET_IFCAP: case PRNIOC_SET_TIMEOUTS: /* * need to retrieve and use the data, but if the * device is busy, wait. */ (void) putq(q, mp); break; case ECPPIOC_GETPARMS: case ECPPIOC_GETREGS: case ECPPIOC_GETPORT: case ECPPIOC_GETDATA: case BPPIOC_GETERR: case BPPIOC_TESTIO: case PRNIOC_GET_IFCAP: case PRNIOC_GET_STATUS: case PRNIOC_GET_1284_STATUS: case PRNIOC_GET_TIMEOUTS: /* data transfered to user space okay */ ecpp_ack_ioctl(q, mp); break; case ECPPIOC_GETDEVID: ecpp_wput_iocdata_devid(q, mp, offsetof(struct ecpp_device_id, rlen)); break; case PRNIOC_GET_1284_DEVID: ecpp_wput_iocdata_devid(q, mp, offsetof(struct prn_1284_device_id, id_rlen)); break; case PRNIOC_GET_IFINFO: ecpp_wput_iocdata_devid(q, mp, offsetof(struct prn_interface_info, if_rlen)); break; default: ecpp_nack_ioctl(q, mp, EINVAL); break; } break; } case M_FLUSH: ecpp_error(pp->dip, "ecpp_wput:M_FLUSH\n"); if (*mp->b_rptr & FLUSHW) { mutex_enter(&pp->umutex); ecpp_flush(pp, FWRITE); mutex_exit(&pp->umutex); } if (*mp->b_rptr & FLUSHR) { mutex_enter(&pp->umutex); ecpp_flush(pp, FREAD); mutex_exit(&pp->umutex); qreply(q, mp); } else { freemsg(mp); } break; case M_READ: /* * When the user calls read(2), M_READ message is sent to us, * first byte of which is the number of requested bytes * We add up user requests and use resulting number * to calculate the reverse transfer block size */ mutex_enter(&pp->umutex); if (pp->e_busy == ECPP_IDLE) { pp->nread += *(size_t *)mp->b_rptr; ecpp_error(pp->dip, "ecpp_wput: M_READ %d", pp->nread); freemsg(mp); } else { ecpp_error(pp->dip, "ecpp_wput: M_READ queueing"); (void) putq(q, mp); } mutex_exit(&pp->umutex); break; default: ecpp_error(pp->dip, "ecpp_wput: bad messagetype 0x%x\n", DB_TYPE(mp)); freemsg(mp); break; } return (0); } /* * Process ECPPIOC_GETDEVID-like ioctls */ static void ecpp_wput_iocdata_devid(queue_t *q, mblk_t *mp, uintptr_t rlen_offset) { struct copyresp *csp; struct ecpp_copystate *stp; mblk_t *datamp; csp = (struct copyresp *)mp->b_rptr; stp = (struct ecpp_copystate *)csp->cp_private->b_rptr; /* determine the state of copyin/copyout process */ switch (stp->state) { case ECPP_STRUCTIN: /* user structure has arrived */ (void) putq(q, mp); break; case ECPP_ADDROUT: /* * data transfered to user space okay * now update user structure */ datamp = allocb(sizeof (int), BPRI_MED); if (datamp == NULL) { ecpp_nack_ioctl(q, mp, ENOSR); break; } *(int *)datamp->b_rptr = *(int *)((char *)&stp->un + rlen_offset); stp->state = ECPP_STRUCTOUT; mcopyout(mp, csp->cp_private, sizeof (int), (char *)stp->uaddr + rlen_offset, datamp); qreply(q, mp); break; case ECPP_STRUCTOUT: /* user structure was updated okay */ freemsg(csp->cp_private); ecpp_ack_ioctl(q, mp); break; default: ecpp_nack_ioctl(q, mp, EINVAL); break; } } static uchar_t ecpp_get_error_status(uchar_t status) { uchar_t pin_status = 0; if (!(status & ECPP_nERR)) { pin_status |= BPP_ERR_ERR; } if (status & ECPP_PE) { pin_status |= BPP_PE_ERR; } if (!(status & ECPP_SLCT)) { pin_status |= BPP_SLCT_ERR; } if (!(status & ECPP_nBUSY)) { pin_status |= BPP_SLCT_ERR; } return (pin_status); } /* * ioctl handler for output PUT procedure. */ static void ecpp_putioc(queue_t *q, mblk_t *mp) { struct iocblk *iocbp; struct ecppunit *pp; pp = (struct ecppunit *)q->q_ptr; iocbp = (struct iocblk *)mp->b_rptr; /* I_STR ioctls are invalid */ if (iocbp->ioc_count != TRANSPARENT) { ecpp_nack_ioctl(q, mp, EINVAL); return; } switch (iocbp->ioc_cmd) { case ECPPIOC_SETPARMS: { mcopyin(mp, NULL, sizeof (struct ecpp_transfer_parms), NULL); qreply(q, mp); break; } case ECPPIOC_GETPARMS: { struct ecpp_transfer_parms xfer_parms; mutex_enter(&pp->umutex); pp->xfer_parms.mode = pp->current_mode; xfer_parms = pp->xfer_parms; mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &xfer_parms, sizeof (xfer_parms)); break; } case ECPPIOC_SETREGS: { mutex_enter(&pp->umutex); if (pp->current_mode != ECPP_DIAG_MODE) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EINVAL); break; } mutex_exit(&pp->umutex); mcopyin(mp, NULL, sizeof (struct ecpp_regs), NULL); qreply(q, mp); break; } case ECPPIOC_GETREGS: { struct ecpp_regs rg; mutex_enter(&pp->umutex); if (pp->current_mode != ECPP_DIAG_MODE) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EINVAL); break; } rg.dsr = DSR_READ(pp); rg.dcr = DCR_READ(pp); mutex_exit(&pp->umutex); ecpp_error(pp->dip, "ECPPIOC_GETREGS: dsr=%x,dcr=%x\n", rg.dsr, rg.dcr); /* these bits must be 1 */ rg.dsr |= ECPP_SETREGS_DSR_MASK; rg.dcr |= ECPP_SETREGS_DCR_MASK; ecpp_putioc_copyout(q, mp, &rg, sizeof (rg)); break; } case ECPPIOC_SETPORT: case ECPPIOC_SETDATA: { mutex_enter(&pp->umutex); if (pp->current_mode != ECPP_DIAG_MODE) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EINVAL); break; } mutex_exit(&pp->umutex); /* * each of the commands fetches a byte quantity. */ mcopyin(mp, NULL, sizeof (uchar_t), NULL); qreply(q, mp); break; } case ECPPIOC_GETDATA: case ECPPIOC_GETPORT: { uchar_t byte; mutex_enter(&pp->umutex); /* must be in diagnostic mode for these commands to work */ if (pp->current_mode != ECPP_DIAG_MODE) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EINVAL); break; } if (iocbp->ioc_cmd == ECPPIOC_GETPORT) { byte = pp->port; } else if (iocbp->ioc_cmd == ECPPIOC_GETDATA) { switch (pp->port) { case ECPP_PORT_PIO: byte = DATAR_READ(pp); break; case ECPP_PORT_TDMA: byte = TFIFO_READ(pp); ecpp_error(pp->dip, "GETDATA=0x%x\n", byte); break; default: ecpp_nack_ioctl(q, mp, EINVAL); break; } } else { mutex_exit(&pp->umutex); ecpp_error(pp->dip, "weird command"); ecpp_nack_ioctl(q, mp, EINVAL); break; } mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &byte, sizeof (byte)); break; } case BPPIOC_GETERR: { struct bpp_error_status bpp_status; mutex_enter(&pp->umutex); bpp_status.timeout_occurred = pp->timeout_error; bpp_status.bus_error = 0; /* not used */ bpp_status.pin_status = ecpp_get_error_status(pp->saved_dsr); mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &bpp_status, sizeof (bpp_status)); break; } case BPPIOC_TESTIO: { mutex_enter(&pp->umutex); if (!((pp->current_mode == ECPP_CENTRONICS) || (pp->current_mode == ECPP_COMPAT_MODE))) { ecpp_nack_ioctl(q, mp, EINVAL); } else { pp->saved_dsr = DSR_READ(pp); if ((pp->saved_dsr & ECPP_PE) || !(pp->saved_dsr & ECPP_SLCT) || !(pp->saved_dsr & ECPP_nERR)) { ecpp_nack_ioctl(q, mp, EIO); } else { ecpp_ack_ioctl(q, mp); } } mutex_exit(&pp->umutex); break; } case PRNIOC_RESET: /* * Initialize interface only if no transfer is in progress */ mutex_enter(&pp->umutex); if (pp->e_busy == ECPP_BUSY) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EIO); } else { (void) ecpp_mode_negotiation(pp, ECPP_CENTRONICS); DCR_WRITE(pp, ECPP_SLCTIN); drv_usecwait(2); DCR_WRITE(pp, ECPP_SLCTIN | ECPP_nINIT); ecpp_default_negotiation(pp); mutex_exit(&pp->umutex); ecpp_ack_ioctl(q, mp); } break; case PRNIOC_GET_IFCAP: { uint_t ifcap; mutex_enter(&pp->umutex); ifcap = ecpp_get_prn_ifcap(pp); mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &ifcap, sizeof (ifcap)); break; } case PRNIOC_SET_IFCAP: { mcopyin(mp, NULL, sizeof (uint_t), NULL); qreply(q, mp); break; } case PRNIOC_GET_TIMEOUTS: { struct prn_timeouts timeouts; mutex_enter(&pp->umutex); timeouts = pp->prn_timeouts; mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &timeouts, sizeof (timeouts)); break; } case PRNIOC_SET_TIMEOUTS: mcopyin(mp, NULL, sizeof (struct prn_timeouts), *(caddr_t *)(void *)mp->b_cont->b_rptr); qreply(q, mp); break; case PRNIOC_GET_STATUS: { uint8_t dsr; uint_t status; mutex_enter(&pp->umutex); /* DSR only makes sense in Centronics & Compat mode */ if (pp->current_mode == ECPP_CENTRONICS || pp->current_mode == ECPP_COMPAT_MODE) { dsr = DSR_READ(pp); if ((dsr & ECPP_PE) || !(dsr & ECPP_SLCT) || !(dsr & ECPP_nERR)) { status = PRN_ONLINE; } else { status = PRN_ONLINE | PRN_READY; } } else { status = PRN_ONLINE | PRN_READY; } mutex_exit(&pp->umutex); ecpp_putioc_copyout(q, mp, &status, sizeof (status)); break; } case PRNIOC_GET_1284_STATUS: { uint8_t dsr; uchar_t status; mutex_enter(&pp->umutex); /* status only makes sense in Centronics & Compat mode */ if (pp->current_mode != ECPP_COMPAT_MODE && pp->current_mode != ECPP_CENTRONICS) { mutex_exit(&pp->umutex); ecpp_nack_ioctl(q, mp, EINVAL); break; } dsr = DSR_READ(pp); /* read status */ mutex_exit(&pp->umutex); ecpp_error(pp->dip, "PRNIOC_GET_STATUS: %x\n", dsr); status = (dsr & (ECPP_SLCT | ECPP_PE | ECPP_nERR)) | (~dsr & ECPP_nBUSY); ecpp_putioc_copyout(q, mp, &status, sizeof (status)); break; } case ECPPIOC_GETDEVID: ecpp_putioc_stateful_copyin(q, mp, sizeof (struct ecpp_device_id)); break; case PRNIOC_GET_1284_DEVID: ecpp_putioc_stateful_copyin(q, mp, sizeof (struct prn_1284_device_id)); break; case PRNIOC_GET_IFINFO: ecpp_putioc_stateful_copyin(q, mp, sizeof (struct prn_interface_info)); break; default: ecpp_error(pp->dip, "putioc: unknown IOCTL: %x\n", iocbp->ioc_cmd); ecpp_nack_ioctl(q, mp, EINVAL); break; } } /* * allocate mblk and copyout the requested number of bytes */ static void ecpp_putioc_copyout(queue_t *q, mblk_t *mp, void *buf, int len) { mblk_t *tmp; if ((tmp = allocb(len, BPRI_MED)) == NULL) { ecpp_nack_ioctl(q, mp, ENOSR); return; } bcopy(buf, tmp->b_wptr, len); mcopyout(mp, NULL, len, NULL, tmp); qreply(q, mp); } /* * copyin the structure using struct ecpp_copystate */ static void ecpp_putioc_stateful_copyin(queue_t *q, mblk_t *mp, size_t size) { mblk_t *tmp; struct ecpp_copystate *stp; if ((tmp = allocb(sizeof (struct ecpp_copystate), BPRI_MED)) == NULL) { ecpp_nack_ioctl(q, mp, EAGAIN); return; } stp = (struct ecpp_copystate *)tmp->b_rptr; stp->state = ECPP_STRUCTIN; stp->uaddr = *(caddr_t *)mp->b_cont->b_rptr; tmp->b_wptr += sizeof (struct ecpp_copystate); mcopyin(mp, tmp, size, stp->uaddr); qreply(q, mp); } /* * read queue is only used when the peripheral sends data faster, * then the application consumes it; * once the low water mark is reached, this routine will be scheduled */ static int ecpp_rsrv(queue_t *q) { struct msgb *mp; /* * send data upstream until next queue is full or the queue is empty */ while (canputnext(q) && (mp = getq(q))) { putnext(q, mp); } /* * if there is still space on the queue, enable backchannel */ if (canputnext(q)) { struct ecppunit *pp = (struct ecppunit *)q->q_ptr; mutex_enter(&pp->umutex); if (pp->e_busy == ECPP_IDLE) { (void) ecpp_idle_phase(pp); cv_signal(&pp->pport_cv); /* signal ecpp_close() */ } mutex_exit(&pp->umutex); } return (0); } static int ecpp_wsrv(queue_t *q) { struct ecppunit *pp = (struct ecppunit *)q->q_ptr; struct msgb *mp; size_t len, total_len; size_t my_ioblock_sz; caddr_t my_ioblock; caddr_t start_addr; mutex_enter(&pp->umutex); ecpp_error(pp->dip, "ecpp_wsrv: e_busy=%x\n", pp->e_busy); /* if channel is actively doing work, wait till completed */ if (pp->e_busy == ECPP_BUSY || pp->e_busy == ECPP_FLUSH) { mutex_exit(&pp->umutex); return (0); } else if (pp->suspended == TRUE) { /* * if the system is about to suspend and ecpp_detach() * is blocked due to active transfers, wake it up and exit */ cv_signal(&pp->pport_cv); mutex_exit(&pp->umutex); return (0); } /* peripheral status should be okay before starting transfer */ if (pp->e_busy == ECPP_ERR) { if (ecpp_check_status(pp) == FAILURE) { if (pp->wsrv_timer_id == 0) { ecpp_error(pp->dip, "wsrv: start wrsv_timer\n"); pp->wsrv_timer_id = timeout(ecpp_wsrv_timer, (caddr_t)pp, drv_usectohz(pp->wsrv_retry * 1000)); } else { ecpp_error(pp->dip, "ecpp_wsrv: wrsv_timer is active\n"); } mutex_exit(&pp->umutex); return (0); } else { pp->e_busy = ECPP_IDLE; } } my_ioblock = pp->ioblock; my_ioblock_sz = IO_BLOCK_SZ; /* * it`s important to null pp->msg here, * cleaning up from the previous transfer attempts */ pp->msg = NULL; start_addr = NULL; len = total_len = 0; /* * The following loop is implemented to gather the * many small writes that the lp subsystem makes and * compile them into one large dma transfer. The len and * total_len variables are a running count of the number of * bytes that have been gathered. They are bcopied to the * ioblock buffer. The pp->e_busy is set to E_BUSY as soon as * we start gathering packets to indicate the following transfer. */ while (mp = getq(q)) { switch (DB_TYPE(mp)) { case M_DATA: pp->e_busy = ECPP_BUSY; len = mp->b_wptr - mp->b_rptr; if ((total_len == 0) && (len >= my_ioblock_sz)) { /* * if the first M_DATA is bigger than ioblock, * just use this mblk and start the transfer */ total_len = len; start_addr = (caddr_t)mp->b_rptr; pp->msg = mp; goto breakout; } else if (total_len + len > my_ioblock_sz) { /* * current M_DATA does not fit in ioblock, * put it back and start the transfer */ (void) putbq(q, mp); goto breakout; } else { /* * otherwise add data to ioblock and free mblk */ bcopy(mp->b_rptr, my_ioblock, len); my_ioblock += len; total_len += len; start_addr = (caddr_t)pp->ioblock; freemsg(mp); } break; case M_IOCTL: /* * Assume a simple loopback test: an application * writes data into the TFIFO, reads it using * ECPPIOC_GETDATA and compares. If the transfer * times out (which is only possible on Grover), * the ioctl might be processed before the data * got to the TFIFO, which leads to miscompare. * So if we met ioctl, postpone it until after xfer. */ if (total_len > 0) { (void) putbq(q, mp); goto breakout; } ecpp_error(pp->dip, "M_IOCTL.\n"); mutex_exit(&pp->umutex); ecpp_putioc(q, mp); mutex_enter(&pp->umutex); break; case M_IOCDATA: { struct copyresp *csp = (struct copyresp *)mp->b_rptr; ecpp_error(pp->dip, "M_IOCDATA\n"); /* * If copy request failed, quit now */ if (csp->cp_rval != 0) { freemsg(mp); break; } switch (csp->cp_cmd) { case ECPPIOC_SETPARMS: case ECPPIOC_SETREGS: case ECPPIOC_SETPORT: case ECPPIOC_SETDATA: case ECPPIOC_GETDEVID: case PRNIOC_SET_IFCAP: case PRNIOC_GET_1284_DEVID: case PRNIOC_SET_TIMEOUTS: case PRNIOC_GET_IFINFO: ecpp_srvioc(q, mp); break; default: ecpp_nack_ioctl(q, mp, EINVAL); break; } break; } case M_CTL: if (pp->e_busy != ECPP_IDLE) { ecpp_error(pp->dip, "wsrv: M_CTL postponed\n"); (void) putbq(q, mp); goto breakout; } else { ecpp_error(pp->dip, "wsrv: M_CTL\n"); } /* sanity check */ if ((mp->b_wptr - mp->b_rptr != sizeof (int)) || (*(int *)mp->b_rptr != ECPP_BACKCHANNEL)) { ecpp_error(pp->dip, "wsrv: bogus M_CTL"); freemsg(mp); break; } else { freemsg(mp); } /* This was a backchannel request */ (void) ecpp_peripheral2host(pp); /* exit if transfer have been initiated */ if (pp->e_busy == ECPP_BUSY) { goto breakout; } break; case M_READ: pp->nread += *(size_t *)mp->b_rptr; freemsg(mp); ecpp_error(pp->dip, "wsrv: M_READ %d", pp->nread); break; default: ecpp_error(pp->dip, "wsrv: should never get here\n"); freemsg(mp); break; } } breakout: /* * If total_len > 0 then start the transfer, otherwise goto idle state */ if (total_len > 0) { ecpp_error(pp->dip, "wsrv:starting: total_len=%d\n", total_len); pp->e_busy = ECPP_BUSY; ecpp_start(pp, start_addr, total_len); } else { ecpp_error(pp->dip, "wsrv:finishing: ebusy=%x\n", pp->e_busy); /* IDLE if xfer_timeout, or FIFO_EMPTY */ if (pp->e_busy == ECPP_IDLE) { (void) ecpp_idle_phase(pp); cv_signal(&pp->pport_cv); /* signal ecpp_close() */ } } mutex_exit(&pp->umutex); return (1); } /* * Ioctl processor for queued ioctl data transfer messages. */ static void ecpp_srvioc(queue_t *q, mblk_t *mp) { struct iocblk *iocbp; struct ecppunit *pp; iocbp = (struct iocblk *)mp->b_rptr; pp = (struct ecppunit *)q->q_ptr; switch (iocbp->ioc_cmd) { case ECPPIOC_SETPARMS: { struct ecpp_transfer_parms *xferp; xferp = (struct ecpp_transfer_parms *)mp->b_cont->b_rptr; if (xferp->write_timeout <= 0 || xferp->write_timeout >= ECPP_MAX_TIMEOUT) { ecpp_nack_ioctl(q, mp, EINVAL); break; } if (!((xferp->mode == ECPP_CENTRONICS) || (xferp->mode == ECPP_COMPAT_MODE) || (xferp->mode == ECPP_NIBBLE_MODE) || (xferp->mode == ECPP_ECP_MODE) || (xferp->mode == ECPP_DIAG_MODE))) { ecpp_nack_ioctl(q, mp, EINVAL); break; } pp->xfer_parms = *xferp; pp->prn_timeouts.tmo_forward = pp->xfer_parms.write_timeout; ecpp_error(pp->dip, "srvioc: current_mode =%x new mode=%x\n", pp->current_mode, pp->xfer_parms.mode); if (ecpp_mode_negotiation(pp, pp->xfer_parms.mode) == FAILURE) { ecpp_nack_ioctl(q, mp, EPROTONOSUPPORT); } else { /* * mode nego was a success. If nibble mode check * back channel and set into REVIDLE. */ if ((pp->current_mode == ECPP_NIBBLE_MODE) && (read_nibble_backchan(pp) == FAILURE)) { /* * problems reading the backchannel * returned to centronics; * ioctl fails. */ ecpp_nack_ioctl(q, mp, EPROTONOSUPPORT); break; } ecpp_ack_ioctl(q, mp); } if (pp->current_mode != ECPP_DIAG_MODE) { pp->port = ECPP_PORT_DMA; } else { pp->port = ECPP_PORT_PIO; } pp->xfer_parms.mode = pp->current_mode; break; } case ECPPIOC_SETREGS: { struct ecpp_regs *rg; uint8_t dcr; rg = (struct ecpp_regs *)mp->b_cont->b_rptr; /* must be in diagnostic mode for these commands to work */ if (pp->current_mode != ECPP_DIAG_MODE) { ecpp_nack_ioctl(q, mp, EINVAL); break; } /* bits 4-7 must be 1 or return EINVAL */ if ((rg->dcr & ECPP_SETREGS_DCR_MASK) != ECPP_SETREGS_DCR_MASK) { ecpp_nack_ioctl(q, mp, EINVAL); break; } /* get the old dcr */ dcr = DCR_READ(pp) & ~ECPP_REV_DIR; /* get the new dcr */ dcr = (dcr & ECPP_SETREGS_DCR_MASK) | (rg->dcr & ~ECPP_SETREGS_DCR_MASK); DCR_WRITE(pp, dcr); ecpp_error(pp->dip, "ECPPIOC_SETREGS:dcr=%x\n", dcr); ecpp_ack_ioctl(q, mp); break; } case ECPPIOC_SETPORT: { uchar_t *port; port = (uchar_t *)mp->b_cont->b_rptr; /* must be in diagnostic mode for these commands to work */ if (pp->current_mode != ECPP_DIAG_MODE) { ecpp_nack_ioctl(q, mp, EINVAL); break; } switch (*port) { case ECPP_PORT_PIO: /* put superio into PIO mode */ ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV); pp->port = *port; ecpp_ack_ioctl(q, mp); break; case ECPP_PORT_TDMA: ecpp_error(pp->dip, "SETPORT: to TDMA\n"); pp->tfifo_intr = 1; /* change to mode 110 */ ECR_WRITE(pp, ECR_mode_110 | ECPP_INTR_MASK | ECPP_INTR_SRV); pp->port = *port; ecpp_ack_ioctl(q, mp); break; default: ecpp_nack_ioctl(q, mp, EINVAL); } break; } case ECPPIOC_SETDATA: { uchar_t *data; data = (uchar_t *)mp->b_cont->b_rptr; /* must be in diagnostic mode for these commands to work */ if (pp->current_mode != ECPP_DIAG_MODE) { ecpp_nack_ioctl(q, mp, EINVAL); break; } switch (pp->port) { case ECPP_PORT_PIO: DATAR_WRITE(pp, *data); ecpp_ack_ioctl(q, mp); break; case ECPP_PORT_TDMA: TFIFO_WRITE(pp, *data); ecpp_ack_ioctl(q, mp); break; default: ecpp_nack_ioctl(q, mp, EINVAL); } break; } case ECPPIOC_GETDEVID: { struct copyresp *csp; struct ecpp_copystate *stp; struct ecpp_device_id *dp; struct ecpp_device_id id; csp = (struct copyresp *)mp->b_rptr; stp = (struct ecpp_copystate *)csp->cp_private->b_rptr; dp = (struct ecpp_device_id *)mp->b_cont->b_rptr; #ifdef _MULTI_DATAMODEL if (IOC_CONVERT_FROM(iocbp) == IOC_ILP32) { struct ecpp_device_id32 *dp32; dp32 = (struct ecpp_device_id32 *)dp; id.mode = dp32->mode; id.len = dp32->len; id.addr = (char *)(uintptr_t)dp32->addr; } else { #endif /* _MULTI_DATAMODEL */ id = *dp; #ifdef _MULTI_DATAMODEL } #endif /* _MULTI_DATAMODEL */ ecpp_srvioc_devid(q, mp, &id, &stp->un.devid.rlen); break; } case PRNIOC_GET_1284_DEVID: { struct copyresp *csp; struct ecpp_copystate *stp; struct prn_1284_device_id *dp; struct ecpp_device_id id; csp = (struct copyresp *)mp->b_rptr; stp = (struct ecpp_copystate *)csp->cp_private->b_rptr; dp = (struct prn_1284_device_id *)mp->b_cont->b_rptr; /* imitate struct ecpp_device_id */ id.mode = ECPP_NIBBLE_MODE; #ifdef _MULTI_DATAMODEL if (IOC_CONVERT_FROM(iocbp) == IOC_ILP32) { struct prn_1284_device_id32 *dp32; dp32 = (struct prn_1284_device_id32 *)dp; id.len = dp32->id_len; id.addr = (char *)(uintptr_t)dp32->id_data; } else { #endif /* _MULTI_DATAMODEL */ id.len = dp->id_len; id.addr = (char *)dp->id_data; #ifdef _MULTI_DATAMODEL } #endif /* _MULTI_DATAMODEL */ ecpp_srvioc_devid(q, mp, &id, (int *)&stp->un.prn_devid.id_rlen); break; } case PRNIOC_SET_IFCAP: { uint_t ifcap, new_ifcap; ifcap = ecpp_get_prn_ifcap(pp); new_ifcap = *(uint_t *)mp->b_cont->b_rptr; if (ifcap == new_ifcap) { ecpp_ack_ioctl(q, mp); break; } /* only changing PRN_BIDI is supported */ if ((ifcap ^ new_ifcap) & ~PRN_BIDI) { ecpp_nack_ioctl(q, mp, EINVAL); break; } if (new_ifcap & PRN_BIDI) { /* go bidirectional */ ecpp_default_negotiation(pp); } else { /* go unidirectional */ (void) ecpp_mode_negotiation(pp, ECPP_CENTRONICS); } ecpp_ack_ioctl(q, mp); break; } case PRNIOC_SET_TIMEOUTS: { struct prn_timeouts *prn_timeouts; prn_timeouts = (struct prn_timeouts *)mp->b_cont->b_rptr; if (prn_timeouts->tmo_forward > ECPP_MAX_TIMEOUT) { ecpp_nack_ioctl(q, mp, EINVAL); break; } pp->prn_timeouts = *prn_timeouts; pp->xfer_parms.write_timeout = (int)prn_timeouts->tmo_forward; ecpp_ack_ioctl(q, mp); break; } case PRNIOC_GET_IFINFO: ecpp_srvioc_prnif(q, mp); break; default: /* unexpected ioctl type */ ecpp_nack_ioctl(q, mp, EINVAL); break; } } static void ecpp_srvioc_devid(queue_t *q, mblk_t *mp, struct ecpp_device_id *id, int *rlen) { struct ecppunit *pp; struct copyresp *csp; struct ecpp_copystate *stp; int error; int len; int mode; mblk_t *datamp; pp = (struct ecppunit *)q->q_ptr; csp = (struct copyresp *)mp->b_rptr; stp = (struct ecpp_copystate *)csp->cp_private->b_rptr; mode = id->mode; /* check arguments */ if ((mode < ECPP_CENTRONICS) || (mode > ECPP_ECP_MODE)) { ecpp_error(pp->dip, "ecpp_srvioc_devid: mode=%x, len=%x\n", mode, id->len); ecpp_nack_ioctl(q, mp, EINVAL); return; } /* Currently only Nibble mode is supported */ if (mode != ECPP_NIBBLE_MODE) { ecpp_nack_ioctl(q, mp, EPROTONOSUPPORT); return; } if ((id->addr == NULL) && (id->len != 0)) { ecpp_nack_ioctl(q, mp, EFAULT); return; } /* read device ID length */ if (error = ecpp_getdevid(pp, NULL, &len, mode)) { ecpp_nack_ioctl(q, mp, error); goto breakout; } /* don't take into account two length bytes */ len -= 2; *rlen = len; /* limit transfer to user buffer length */ if (id->len < len) { len = id->len; } if (len == 0) { /* just return rlen */ stp->state = ECPP_ADDROUT; ecpp_wput_iocdata_devid(q, mp, (uintptr_t)rlen - (uintptr_t)&stp->un); goto breakout; } if ((datamp = allocb(len, BPRI_MED)) == NULL) { ecpp_nack_ioctl(q, mp, ENOSR); goto breakout; } /* read ID string */ error = ecpp_getdevid(pp, datamp->b_rptr, &len, mode); if (error) { freemsg(datamp); ecpp_nack_ioctl(q, mp, error); goto breakout; } else { datamp->b_wptr += len; stp->state = ECPP_ADDROUT; mcopyout(mp, csp->cp_private, len, id->addr, datamp); qreply(q, mp); } return; breakout: (void) ecpp_1284_termination(pp); } /* * PRNIOC_GET_IFINFO: return prnio interface info string */ static void ecpp_srvioc_prnif(queue_t *q, mblk_t *mp) { struct copyresp *csp; struct ecpp_copystate *stp; uint_t len; struct prn_interface_info *ip; struct prn_interface_info info; mblk_t *datamp; #ifdef _MULTI_DATAMODEL struct iocblk *iocbp = (struct iocblk *)mp->b_rptr; #endif csp = (struct copyresp *)mp->b_rptr; stp = (struct ecpp_copystate *)csp->cp_private->b_rptr; ip = (struct prn_interface_info *)mp->b_cont->b_rptr; #ifdef _MULTI_DATAMODEL if (IOC_CONVERT_FROM(iocbp) == IOC_ILP32) { struct prn_interface_info32 *ip32; ip32 = (struct prn_interface_info32 *)ip; info.if_len = ip32->if_len; info.if_data = (char *)(uintptr_t)ip32->if_data; } else { #endif /* _MULTI_DATAMODEL */ info = *ip; #ifdef _MULTI_DATAMODEL } #endif /* _MULTI_DATAMODEL */ len = strlen(prn_ifinfo); stp->un.prn_if.if_rlen = len; stp->state = ECPP_ADDROUT; /* check arguments */ if ((info.if_data == NULL) && (info.if_len != 0)) { ecpp_nack_ioctl(q, mp, EFAULT); return; } if (info.if_len == 0) { /* just copyout rlen */ ecpp_wput_iocdata_devid(q, mp, offsetof(struct prn_interface_info, if_rlen)); return; } /* if needed, trim to the buffer size */ if (len > info.if_len) { len = info.if_len; } if ((datamp = allocb(len, BPRI_MED)) == NULL) { ecpp_nack_ioctl(q, mp, ENOSR); return; } bcopy(&prn_ifinfo[0], datamp->b_wptr, len); datamp->b_wptr += len; mcopyout(mp, csp->cp_private, len, info.if_data, datamp); qreply(q, mp); } static void ecpp_flush(struct ecppunit *pp, int cmd) { queue_t *q; uint8_t ecr, dcr; timeout_id_t timeout_id, fifo_timer_id, wsrv_timer_id; ASSERT(mutex_owned(&pp->umutex)); if (!(cmd & FWRITE)) { return; } q = pp->writeq; timeout_id = fifo_timer_id = wsrv_timer_id = 0; ecpp_error(pp->dip, "ecpp_flush e_busy=%x\n", pp->e_busy); /* if there is an ongoing DMA, it needs to be turned off. */ switch (pp->e_busy) { case ECPP_BUSY: /* * Change the port status to ECPP_FLUSH to * indicate to ecpp_wsrv that the wq is being flushed. */ pp->e_busy = ECPP_FLUSH; /* * dma_cancelled indicates to ecpp_isr() that we have * turned off the DMA. Since the mutex is held, ecpp_isr() * may be blocked. Once ecpp_flush() finishes and ecpp_isr() * gains the mutex, ecpp_isr() will have a _reset_ DMAC. Most * significantly, the DMAC will be reset after ecpp_isr() was * invoked. Therefore we need to have a flag "dma_cancelled" * to signify when the described condition has occured. If * ecpp_isr() notes a dma_cancelled, it will ignore the DMAC csr * and simply claim the interupt. */ pp->dma_cancelled = TRUE; /* either DMA or PIO transfer */ if (COMPAT_DMA(pp) || (pp->current_mode == ECPP_ECP_MODE) || (pp->current_mode == ECPP_DIAG_MODE)) { /* * if the bcr is zero, then DMA is complete and * we are waiting for the fifo to drain. Therefore, * turn off dma. */ if (ECPP_DMA_STOP(pp, NULL) == FAILURE) { ecpp_error(pp->dip, "ecpp_flush: dma_stop failed.\n"); } /* * If the status of the port is ECPP_BUSY, * the DMA is stopped by either explicitly above, or by * ecpp_isr() but the FIFO hasn't drained yet. In either * case, we need to unbind the dma mappings. */ if (ddi_dma_unbind_handle( pp->dma_handle) != DDI_SUCCESS) ecpp_error(pp->dip, "ecpp_flush: unbind failed.\n"); if (pp->msg != NULL) { freemsg(pp->msg); pp->msg = NULL; } } else { /* * PIO transfer: disable nAck interrups */ dcr = DCR_READ(pp); dcr &= ~(ECPP_REV_DIR | ECPP_INTR_EN); DCR_WRITE(pp, dcr); ECPP_MASK_INTR(pp); } /* * The transfer is cleaned up. There may or may not be data * in the fifo. We don't care at this point. Ie. SuperIO may * transfer the remaining bytes in the fifo or not. it doesn't * matter. All that is important at this stage is that no more * fifo timers are started. */ timeout_id = pp->timeout_id; fifo_timer_id = pp->fifo_timer_id; pp->timeout_id = pp->fifo_timer_id = 0; pp->softintr_pending = 0; break; case ECPP_ERR: /* * Change the port status to ECPP_FLUSH to * indicate to ecpp_wsrv that the wq is being flushed. */ pp->e_busy = ECPP_FLUSH; /* * Most likely there are mblks in the queue, * but the driver can not transmit because * of the bad port status. In this case, * ecpp_flush() should make sure ecpp_wsrv_timer() * is turned off. */ wsrv_timer_id = pp->wsrv_timer_id; pp->wsrv_timer_id = 0; break; case ECPP_IDLE: /* No work to do. Ready to flush */ break; default: ecpp_error(pp->dip, "ecpp_flush: illegal state %x\n", pp->e_busy); } /* in DIAG mode clear TFIFO if needed */ if (pp->current_mode == ECPP_DIAG_MODE) { ecr = ECR_READ(pp); if (!(ecr & ECPP_FIFO_EMPTY)) { ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_001); ECR_WRITE(pp, ecr); } } /* Discard all messages on the output queue. */ flushq(q, FLUSHDATA); /* The port is no longer flushing or dma'ing for that matter. */ pp->e_busy = ECPP_IDLE; /* Set the right phase */ if (pp->current_mode == ECPP_ECP_MODE) { if (pp->current_phase == ECPP_PHASE_ECP_REV_XFER) { pp->current_phase = ECPP_PHASE_ECP_REV_IDLE; } else { pp->current_phase = ECPP_PHASE_ECP_FWD_IDLE; } } /* cancel timeouts if any */ mutex_exit(&pp->umutex); if (timeout_id) { (void) untimeout(timeout_id); } if (fifo_timer_id) { (void) untimeout(fifo_timer_id); } if (wsrv_timer_id) { (void) untimeout(wsrv_timer_id); } mutex_enter(&pp->umutex); cv_signal(&pp->pport_cv); /* wake up ecpp_close() */ } static void ecpp_start(struct ecppunit *pp, caddr_t addr, size_t len) { ASSERT(mutex_owned(&pp->umutex)); ASSERT(pp->e_busy == ECPP_BUSY); ecpp_error(pp->dip, "ecpp_start:current_mode=%x,current_phase=%x,ecr=%x,len=%d\n", pp->current_mode, pp->current_phase, ECR_READ(pp), len); pp->dma_dir = DDI_DMA_WRITE; /* this is a forward transfer */ switch (pp->current_mode) { case ECPP_NIBBLE_MODE: (void) ecpp_1284_termination(pp); /* After termination we are either Compatible or Centronics */ /* FALLTHRU */ case ECPP_CENTRONICS: case ECPP_COMPAT_MODE: if (pp->io_mode == ECPP_DMA) { if (ecpp_init_dma_xfer(pp, addr, len) == FAILURE) { return; } } else { /* PIO mode */ if (ecpp_prep_pio_xfer(pp, addr, len) == FAILURE) { return; } (void) ecpp_pio_writeb(pp); } break; case ECPP_DIAG_MODE: { int oldlen; /* put superio into TFIFO mode, if not already */ ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_110); /* * DMA would block if the TFIFO is not empty * if by this moment nobody read these bytes, they`re gone */ drv_usecwait(1); if (!(ECR_READ(pp) & ECPP_FIFO_EMPTY)) { ecpp_error(pp->dip, "ecpp_start: TFIFO not empty, clearing\n"); ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_001); ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_110); } /* we can DMA at most 16 bytes into TFIFO */ oldlen = len; if (len > ECPP_FIFO_SZ) { len = ECPP_FIFO_SZ; } if (ecpp_init_dma_xfer(pp, addr, len) == FAILURE) { return; } /* put the rest of data back on the queue */ if (oldlen > len) { ecpp_putback_untransfered(pp, addr + len, oldlen - len); } break; } case ECPP_ECP_MODE: ASSERT(pp->current_phase == ECPP_PHASE_ECP_FWD_IDLE || pp->current_phase == ECPP_PHASE_ECP_REV_IDLE); /* if in Reverse Phase negotiate to Forward */ if (pp->current_phase == ECPP_PHASE_ECP_REV_IDLE) { if (ecp_reverse2forward(pp) == FAILURE) { if (pp->msg) { (void) putbq(pp->writeq, pp->msg); } else { ecpp_putback_untransfered(pp, addr, len); } } } if (ecpp_init_dma_xfer(pp, addr, len) == FAILURE) { return; } break; } /* schedule transfer timeout */ pp->timeout_id = timeout(ecpp_xfer_timeout, (caddr_t)pp, pp->xfer_parms.write_timeout * drv_usectohz(1000000)); } /* * Transfer a PIO "block" a byte at a time. * The block is starts at addr and ends at pp->last_byte */ static uint8_t ecpp_prep_pio_xfer(struct ecppunit *pp, caddr_t addr, size_t len) { pp->next_byte = addr; pp->last_byte = (caddr_t)((ulong_t)addr + len); if (ecpp_check_status(pp) == FAILURE) { /* * if status signals are bad, do not start PIO, * put everything back on the queue. */ ecpp_error(pp->dip, "ecpp_prep_pio_xfer:suspend PIO len=%d\n", len); if (pp->msg != NULL) { /* * this circumstance we want to copy the * untransfered section of msg to a new mblk, * then free the orignal one. */ ecpp_putback_untransfered(pp, (void *)pp->msg->b_rptr, len); ecpp_error(pp->dip, "ecpp_prep_pio_xfer: len1=%d\n", len); freemsg(pp->msg); pp->msg = NULL; } else { ecpp_putback_untransfered(pp, pp->ioblock, len); ecpp_error(pp->dip, "ecpp_prep_pio_xfer: len2=%d\n", len); } qenable(pp->writeq); return (FAILURE); } pp->dma_cancelled = FALSE; /* pport must be in PIO mode */ if (ecr_write(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV) != SUCCESS) { ecpp_error(pp->dip, "ecpp_prep_pio_xfer: failed w/ECR.\n"); } ecpp_error(pp->dip, "ecpp_prep_pio_xfer: dcr=%x ecr=%x\n", DCR_READ(pp), ECR_READ(pp)); return (SUCCESS); } static uint8_t ecpp_init_dma_xfer(struct ecppunit *pp, caddr_t addr, size_t len) { uint8_t ecr_mode[] = { 0, ECR_mode_010, /* Centronix */ ECR_mode_010, /* Compat */ 0, /* Byte */ 0, /* Nibble */ ECR_mode_011, /* ECP */ 0, /* Failure */ ECR_mode_110, /* Diag */ }; uint8_t ecr; ASSERT((pp->current_mode <= ECPP_DIAG_MODE) && (ecr_mode[pp->current_mode] != 0)); if (ecpp_setup_dma_resources(pp, addr, len) == FAILURE) { qenable(pp->writeq); return (FAILURE); } if (ecpp_check_status(pp) == FAILURE) { /* * if status signals are bad, do not start DMA, but * rather put everything back on the queue. */ ecpp_error(pp->dip, "ecpp_init_dma_xfer: suspending DMA len=%d\n", pp->dma_cookie.dmac_size); if (pp->msg != NULL) { /* * this circumstance we want to copy the * untransfered section of msg to a new mblk, * then free the orignal one. */ ecpp_putback_untransfered(pp, (void *)pp->msg->b_rptr, len); ecpp_error(pp->dip, "ecpp_init_dma_xfer:a:len=%d\n", len); freemsg(pp->msg); pp->msg = NULL; } else { ecpp_putback_untransfered(pp, pp->ioblock, len); ecpp_error(pp->dip, "ecpp_init_dma_xfer:b:len=%d\n", len); } if (ddi_dma_unbind_handle(pp->dma_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecpp_init_dma_xfer: unbind FAILURE.\n"); } qenable(pp->writeq); return (FAILURE); } pp->xfercnt = pp->resid = len; pp->dma_cancelled = FALSE; pp->tfifo_intr = 0; /* set the right ECR mode and disable DMA */ ecr = ecr_mode[pp->current_mode]; (void) ecr_write(pp, ecr | ECPP_INTR_SRV | ECPP_INTR_MASK); /* prepare DMAC for a transfer */ if (ECPP_DMA_START(pp) == FAILURE) { ecpp_error(pp->dip, "ecpp_init_dma_xfer: dma_start FAILED.\n"); return (FAILURE); } /* GO! */ (void) ecr_write(pp, ecr | ECPP_DMA_ENABLE | ECPP_INTR_MASK); return (SUCCESS); } static uint8_t ecpp_setup_dma_resources(struct ecppunit *pp, caddr_t addr, size_t len) { int err; off_t woff; size_t wlen; ASSERT(pp->dma_dir == DDI_DMA_READ || pp->dma_dir == DDI_DMA_WRITE); err = ddi_dma_addr_bind_handle(pp->dma_handle, NULL, addr, len, pp->dma_dir | DDI_DMA_PARTIAL, DDI_DMA_DONTWAIT, NULL, &pp->dma_cookie, &pp->dma_cookie_count); switch (err) { case DDI_DMA_MAPPED: ecpp_error(pp->dip, "ecpp_setup_dma: DMA_MAPPED\n"); pp->dma_nwin = 1; pp->dma_curwin = 1; break; case DDI_DMA_PARTIAL_MAP: { ecpp_error(pp->dip, "ecpp_setup_dma: DMA_PARTIAL_MAP\n"); if (ddi_dma_numwin(pp->dma_handle, &pp->dma_nwin) != DDI_SUCCESS) { (void) ddi_dma_unbind_handle(pp->dma_handle); return (FAILURE); } pp->dma_curwin = 1; /* * The very first window is returned by bind_handle, * but we must do this explicitly here, otherwise * next getwin would return wrong cookie dmac_size */ if (ddi_dma_getwin(pp->dma_handle, 0, &woff, &wlen, &pp->dma_cookie, &pp->dma_cookie_count) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecpp_setup_dma: ddi_dma_getwin failed!"); (void) ddi_dma_unbind_handle(pp->dma_handle); return (FAILURE); } ecpp_error(pp->dip, "ecpp_setup_dma: cookies=%d, windows=%d" " addr=%lx len=%d\n", pp->dma_cookie_count, pp->dma_nwin, pp->dma_cookie.dmac_address, pp->dma_cookie.dmac_size); break; } default: ecpp_error(pp->dip, "ecpp_setup_dma: err=%x\n", err); return (FAILURE); } return (SUCCESS); } static void ecpp_ack_ioctl(queue_t *q, mblk_t *mp) { struct iocblk *iocbp; mp->b_datap->db_type = M_IOCACK; mp->b_wptr = mp->b_rptr + sizeof (struct iocblk); if (mp->b_cont) { freemsg(mp->b_cont); mp->b_cont = NULL; } iocbp = (struct iocblk *)mp->b_rptr; iocbp->ioc_error = 0; iocbp->ioc_count = 0; iocbp->ioc_rval = 0; qreply(q, mp); } static void ecpp_nack_ioctl(queue_t *q, mblk_t *mp, int err) { struct iocblk *iocbp; mp->b_datap->db_type = M_IOCNAK; mp->b_wptr = mp->b_rptr + sizeof (struct iocblk); iocbp = (struct iocblk *)mp->b_rptr; iocbp->ioc_error = err; if (mp->b_cont) { freemsg(mp->b_cont); mp->b_cont = NULL; } qreply(q, mp); } uint_t ecpp_isr(caddr_t arg) { struct ecppunit *pp = (struct ecppunit *)(void *)arg; uint32_t dcsr; uint8_t dsr; int cheerio_pend_counter; int retval = DDI_INTR_UNCLAIMED; hrtime_t now; mutex_enter(&pp->umutex); /* * interrupt may occur while other thread is holding the lock * and cancels DMA transfer (e.g. ecpp_flush()) * since it cannot cancel the interrupt thread, * it just sets dma_cancelled to TRUE, * telling interrupt handler to exit immediately */ if (pp->dma_cancelled == TRUE) { ecpp_error(pp->dip, "dma-cancel isr\n"); pp->intr_hard++; pp->dma_cancelled = FALSE; mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } /* Southbridge interrupts are handled separately */ #if defined(__x86) if (pp->hw == &x86) #else if (pp->hw == &m1553) #endif { retval = ecpp_M1553_intr(pp); if (retval == DDI_INTR_UNCLAIMED) { goto unexpected; } mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } /* * the intr is through the motherboard. it is faster than PCI route. * sometimes ecpp_isr() is invoked before cheerio csr is updated. */ cheerio_pend_counter = ecpp_isr_max_delay; dcsr = GET_DMAC_CSR(pp); while (!(dcsr & DCSR_INT_PEND) && cheerio_pend_counter-- > 0) { drv_usecwait(1); dcsr = GET_DMAC_CSR(pp); } /* * This is a workaround for what seems to be a timing problem * with the delivery of interrupts and CSR updating with the * ebus2 csr, superio and the n_ERR pin from the peripheral. * * delay is not needed for PIO mode */ if (!COMPAT_PIO(pp)) { drv_usecwait(100); dcsr = GET_DMAC_CSR(pp); } /* on 97317 in Extended mode IRQ_ST of DSR is deasserted when read */ dsr = DSR_READ(pp); /* * check if interrupt is for this device: * it should be reflected either in cheerio DCSR register * or in IRQ_ST bit of DSR on 97317 */ if ((dcsr & DCSR_INT_PEND) == 0) { if (pp->hw != &pc97317) { goto unclaimed; } /* * on Excalibur, reading DSR will deassert SuperIO IRQx line * RIO's DCSR_INT_PEND seems to follow IRQx transitions, * so if DSR is read after interrupt occured, but before * we get here, IRQx and hence INT_PEND will be deasserted * as a result, we can miss a service interrupt in PIO mode * * malicious DSR reader is BPPIOC_TESTIO, which is called * by LP in between data blocks to check printer status * this workaround lets us not to miss an interrupt * * also, nErr interrupt (ECP mode) not always reflected in DCSR */ if (((dsr & ECPP_IRQ_ST) == 0) || ((COMPAT_PIO(pp)) && (pp->e_busy == ECPP_BUSY)) || (((dsr & ECPP_nERR) == 0) && (pp->current_mode == ECPP_ECP_MODE))) { dcsr = 0; } else { goto unclaimed; } } pp->intr_hard++; /* the intr is for us - check all possible interrupt sources */ if (dcsr & DCSR_ERR_PEND) { size_t bcr; /* we are expecting a data transfer interrupt */ ASSERT(pp->e_busy == ECPP_BUSY); /* * some kind of DMA error */ if (ECPP_DMA_STOP(pp, &bcr) == FAILURE) { ecpp_error(pp->dip, "ecpp_isr: dma_stop failed\n"); } ecpp_error(pp->dip, "ecpp_isr: DMAC ERROR bcr=%d\n", bcr); ecpp_xfer_cleanup(pp); if (ddi_dma_unbind_handle(pp->dma_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecpp_isr(e): unbind failed\n"); } mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } if (dcsr & DCSR_TC) { retval = ecpp_dma_ihdlr(pp); mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } if (COMPAT_PIO(pp)) { retval = ecpp_pio_ihdlr(pp); mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } /* does peripheral need attention? */ if ((dsr & ECPP_nERR) == 0) { retval = ecpp_nErr_ihdlr(pp); mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } pp->intr_hard--; unexpected: pp->intr_spurious++; /* * The following procedure tries to prevent soft hangs * in event of peripheral/superio misbehaviour: * if number of unexpected interrupts in the last SPUR_PERIOD ns * exceeded SPUR_CRITICAL, then shut up interrupts */ now = gethrtime(); if (pp->lastspur == 0 || now - pp->lastspur > SPUR_PERIOD) { /* last unexpected interrupt was long ago */ pp->lastspur = now; pp->nspur = 1; } else { /* last unexpected interrupt was recently */ pp->nspur++; } if (pp->nspur >= SPUR_CRITICAL) { ECPP_MASK_INTR(pp); ECR_WRITE(pp, ECR_READ(pp) | ECPP_INTR_MASK | ECPP_INTR_SRV); pp->nspur = 0; cmn_err(CE_NOTE, "%s%d: too many interrupt requests", ddi_get_name(pp->dip), ddi_get_instance(pp->dip)); } else { ECR_WRITE(pp, ECR_READ(pp) | ECPP_INTR_SRV | ECPP_INTR_MASK); } ecpp_error(pp->dip, "isr:unknown: dcsr=%x ecr=%x dsr=%x dcr=%x\nmode=%x phase=%x\n", dcsr, ECR_READ(pp), dsr, DCR_READ(pp), pp->current_mode, pp->current_phase); mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); unclaimed: pp->intr_spurious++; ecpp_error(pp->dip, "isr:UNCL: dcsr=%x ecr=%x dsr=%x dcr=%x\nmode=%x phase=%x\n", dcsr, ECR_READ(pp), DSR_READ(pp), DCR_READ(pp), pp->current_mode, pp->current_phase); mutex_exit(&pp->umutex); return (DDI_INTR_UNCLAIMED); } /* * M1553 intr handler */ static uint_t ecpp_M1553_intr(struct ecppunit *pp) { int retval = DDI_INTR_UNCLAIMED; pp->intr_hard++; if (pp->e_busy == ECPP_BUSY) { /* Centronics or Compat PIO transfer */ if (COMPAT_PIO(pp)) { return (ecpp_pio_ihdlr(pp)); } /* Centronics or Compat DMA transfer */ if (COMPAT_DMA(pp) || (pp->current_mode == ECPP_ECP_MODE) || (pp->current_mode == ECPP_DIAG_MODE)) { return (ecpp_dma_ihdlr(pp)); } } /* Nibble or ECP backchannel request? */ if ((DSR_READ(pp) & ECPP_nERR) == 0) { return (ecpp_nErr_ihdlr(pp)); } return (retval); } /* * DMA completion interrupt handler */ static uint_t ecpp_dma_ihdlr(struct ecppunit *pp) { clock_t tm; ecpp_error(pp->dip, "ecpp_dma_ihdlr(%x): ecr=%x, dsr=%x, dcr=%x\n", pp->current_mode, ECR_READ(pp), DSR_READ(pp), DCR_READ(pp)); /* we are expecting a data transfer interrupt */ ASSERT(pp->e_busy == ECPP_BUSY); /* Intr generated while invoking TFIFO mode. Exit */ if (pp->tfifo_intr == 1) { pp->tfifo_intr = 0; ecpp_error(pp->dip, "ecpp_dma_ihdlr: tfifo_intr is 1\n"); return (DDI_INTR_CLAIMED); } if (ECPP_DMA_STOP(pp, NULL) == FAILURE) { ecpp_error(pp->dip, "ecpp_dma_ihdlr: dma_stop failed\n"); } if (pp->current_mode == ECPP_ECP_MODE && pp->current_phase == ECPP_PHASE_ECP_REV_XFER) { ecpp_ecp_read_completion(pp); } else { /* * fifo_timer() will do the cleanup when the FIFO drains */ if ((ECR_READ(pp) & ECPP_FIFO_EMPTY) || (pp->current_mode == ECPP_DIAG_MODE)) { tm = 0; /* no use in waiting if FIFO is already empty */ } else { tm = drv_usectohz(FIFO_DRAIN_PERIOD); } pp->fifo_timer_id = timeout(ecpp_fifo_timer, (caddr_t)pp, tm); } /* * Stop the DMA transfer timeout timer * this operation will temporarily give up the mutex, * so we do it in the end of the handler to avoid races */ ecpp_untimeout_unblock(pp, &pp->timeout_id); return (DDI_INTR_CLAIMED); } /* * ecpp_pio_ihdlr() is a PIO interrupt processing routine * It masks interrupts, updates statistics and initiates next byte transfer */ static uint_t ecpp_pio_ihdlr(struct ecppunit *pp) { ASSERT(mutex_owned(&pp->umutex)); ASSERT(pp->e_busy == ECPP_BUSY); /* update statistics */ pp->joblen++; pp->ctxpio_obytes++; /* disable nAck interrups */ ECPP_MASK_INTR(pp); DCR_WRITE(pp, DCR_READ(pp) & ~(ECPP_REV_DIR | ECPP_INTR_EN)); /* * If it was the last byte of the data block cleanup, * otherwise trigger a soft interrupt to send the next byte */ if (pp->next_byte >= pp->last_byte) { ecpp_xfer_cleanup(pp); ecpp_error(pp->dip, "ecpp_pio_ihdlr: pp->joblen=%d,pp->ctx_cf=%d,\n", pp->joblen, pp->ctx_cf); } else { if (pp->softintr_pending) { ecpp_error(pp->dip, "ecpp_pio_ihdlr:E: next byte in progress\n"); } else { pp->softintr_flags = ECPP_SOFTINTR_PIONEXT; pp->softintr_pending = 1; ddi_trigger_softintr(pp->softintr_id); } } return (DDI_INTR_CLAIMED); } /* * ecpp_pio_writeb() sends a byte using Centronics handshake */ static void ecpp_pio_writeb(struct ecppunit *pp) { uint8_t dcr; dcr = DCR_READ(pp) & ~ECPP_REV_DIR; dcr |= ECPP_INTR_EN; /* send the next byte */ DATAR_WRITE(pp, *(pp->next_byte++)); drv_usecwait(pp->data_setup_time); /* Now Assert (neg logic) nStrobe */ if (dcr_write(pp, dcr | ECPP_STB) == FAILURE) { ecpp_error(pp->dip, "ecpp_pio_writeb:1: failed w/DCR\n"); } /* Enable nAck interrupts */ (void) DSR_READ(pp); /* ensure IRQ_ST is armed */ ECPP_UNMASK_INTR(pp); drv_usecwait(pp->strobe_pulse_width); if (dcr_write(pp, dcr & ~ECPP_STB) == FAILURE) { ecpp_error(pp->dip, "ecpp_pio_writeb:2: failed w/DCR\n"); } } /* * Backchannel request interrupt handler */ static uint_t ecpp_nErr_ihdlr(struct ecppunit *pp) { ecpp_error(pp->dip, "ecpp_nErr_ihdlr: mode=%x, phase=%x\n", pp->current_mode, pp->current_phase); if (pp->oflag != TRUE) { ecpp_error(pp->dip, "ecpp_nErr_ihdlr: not open!\n"); return (DDI_INTR_UNCLAIMED); } if (pp->e_busy == ECPP_BUSY) { ecpp_error(pp->dip, "ecpp_nErr_ihdlr: busy\n"); ECR_WRITE(pp, ECR_READ(pp) | ECPP_INTR_MASK); return (DDI_INTR_CLAIMED); } /* mask nErr & nAck interrupts */ ECPP_MASK_INTR(pp); DCR_WRITE(pp, DCR_READ(pp) & ~(ECPP_INTR_EN | ECPP_REV_DIR)); ECR_WRITE(pp, ECR_READ(pp) | ECPP_INTR_MASK); /* going reverse */ switch (pp->current_mode) { case ECPP_ECP_MODE: /* * Peripheral asserts nPeriphRequest (nFault) */ break; case ECPP_NIBBLE_MODE: /* * Event 18: Periph asserts nErr to indicate data avail * Event 19: After waiting minimum pulse width, * periph sets nAck high to generate an interrupt * * Interface is in Interrupt Phase */ pp->current_phase = ECPP_PHASE_NIBT_REVINTR; break; default: ecpp_error(pp->dip, "ecpp_nErr_ihdlr: wrong mode!\n"); return (DDI_INTR_UNCLAIMED); } (void) ecpp_backchan_req(pp); /* put backchannel request on the wq */ return (DDI_INTR_CLAIMED); } /* * Softintr handler does work according to softintr_flags: * in case of ECPP_SOFTINTR_PIONEXT it sends next byte of PIO transfer */ static uint_t ecpp_softintr(caddr_t arg) { struct ecppunit *pp = (struct ecppunit *)arg; uint32_t unx_len, ecpp_reattempts = 0; mutex_enter(&pp->umutex); pp->intr_soft++; if (!pp->softintr_pending) { mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } else { pp->softintr_pending = 0; } if (pp->softintr_flags & ECPP_SOFTINTR_PIONEXT) { pp->softintr_flags &= ~ECPP_SOFTINTR_PIONEXT; /* * Sent next byte in PIO mode */ ecpp_reattempts = 0; do { if (ecpp_check_status(pp) == SUCCESS) { pp->e_busy = ECPP_BUSY; break; } drv_usecwait(1); if (pp->isr_reattempt_high < ecpp_reattempts) { pp->isr_reattempt_high = ecpp_reattempts; } } while (++ecpp_reattempts < pp->wait_for_busy); /* if the peripheral still not recovered suspend the transfer */ if (pp->e_busy == ECPP_ERR) { ++pp->ctx_cf; /* check status fail */ ecpp_error(pp->dip, "ecpp_softintr:check_status:F: " "dsr=%x jl=%d cf_isr=%d\n", DSR_READ(pp), pp->joblen, pp->ctx_cf); /* * if status signals are bad, * put everything back on the wq. */ unx_len = pp->last_byte - pp->next_byte; if (pp->msg != NULL) { ecpp_putback_untransfered(pp, (void *)pp->msg->b_rptr, unx_len); ecpp_error(pp->dip, "ecpp_softintr:e1:unx_len=%d\n", unx_len); freemsg(pp->msg); pp->msg = NULL; } else { ecpp_putback_untransfered(pp, pp->next_byte, unx_len); ecpp_error(pp->dip, "ecpp_softintr:e2:unx_len=%d\n", unx_len); } ecpp_xfer_cleanup(pp); pp->e_busy = ECPP_ERR; qenable(pp->writeq); } else { /* send the next one */ pp->e_busy = ECPP_BUSY; (void) ecpp_pio_writeb(pp); } } mutex_exit(&pp->umutex); return (DDI_INTR_CLAIMED); } /* * Transfer clean-up: * shut down the DMAC * stop the transfer timer * enable write queue */ static void ecpp_xfer_cleanup(struct ecppunit *pp) { ASSERT(mutex_owned(&pp->umutex)); /* * if we did not use the ioblock, the mblk that * was used should be freed. */ if (pp->msg != NULL) { freemsg(pp->msg); pp->msg = NULL; } /* The port is no longer active */ pp->e_busy = ECPP_IDLE; /* Stop the transfer timeout timer */ ecpp_untimeout_unblock(pp, &pp->timeout_id); qenable(pp->writeq); } /*VARARGS*/ static void ecpp_error(dev_info_t *dip, char *fmt, ...) { static long last; static char *lastfmt; char msg_buffer[255]; va_list ap; time_t now; if (!ecpp_debug) { return; } /* * This function is supposed to be a quick non-blockable * wrapper for cmn_err(9F), which provides a sensible degree * of debug message throttling. Not using any type of lock * is a requirement, but this also leaves two static variables * - last and lastfmt - unprotected. However, this will not do * any harm to driver functionality, it can only weaken throttling. * The following directive asks warlock to not worry about these * variables. */ _NOTE(NOW_INVISIBLE_TO_OTHER_THREADS(last, lastfmt)) /* * Don't print same error message too often. */ now = gethrestime_sec(); if ((last == (now & ~1)) && (lastfmt == fmt)) return; last = now & ~1; lastfmt = fmt; va_start(ap, fmt); (void) vsprintf(msg_buffer, fmt, ap); cmn_err(CE_CONT, "%s%d: %s", ddi_get_name(dip), ddi_get_instance(dip), msg_buffer); va_end(ap); } /* * Forward transfer timeout */ static void ecpp_xfer_timeout(void *arg) { struct ecppunit *pp = arg; void *unx_addr; size_t unx_len, xferd; uint8_t dcr; timeout_id_t fifo_timer_id; mutex_enter(&pp->umutex); if (pp->timeout_id == 0) { mutex_exit(&pp->umutex); return; } else { pp->timeout_id = 0; } pp->xfer_tout++; pp->dma_cancelled = TRUE; /* prevent race with isr() */ if (COMPAT_PIO(pp)) { /* * PIO mode timeout */ /* turn off nAck interrupts */ dcr = DCR_READ(pp); (void) dcr_write(pp, dcr & ~(ECPP_REV_DIR | ECPP_INTR_EN)); ECPP_MASK_INTR(pp); pp->softintr_pending = 0; unx_len = pp->last_byte - pp->next_byte; ecpp_error(pp->dip, "xfer_timeout: unx_len=%d\n", unx_len); if (unx_len > 0) { unx_addr = pp->next_byte; } else { ecpp_xfer_cleanup(pp); qenable(pp->writeq); mutex_exit(&pp->umutex); return; } } else { /* * DMA mode timeout * * If DMAC fails to shut off, continue anyways and attempt * to put untransfered data back on queue. */ if (ECPP_DMA_STOP(pp, &unx_len) == FAILURE) { ecpp_error(pp->dip, "ecpp_xfer_timeout: failed dma_stop\n"); } ecpp_error(pp->dip, "xfer_timeout: unx_len=%d\n", unx_len); if (ddi_dma_unbind_handle(pp->dma_handle) == DDI_FAILURE) { ecpp_error(pp->dip, "ecpp_xfer_timeout: failed unbind\n"); } /* * if the bcr is zero, then DMA is complete and * we are waiting for the fifo to drain. So let * ecpp_fifo_timer() look after the clean up. */ if (unx_len == 0) { qenable(pp->writeq); mutex_exit(&pp->umutex); return; } else { xferd = pp->dma_cookie.dmac_size - unx_len; pp->resid -= xferd; unx_len = pp->resid; /* update statistics */ pp->obytes[pp->current_mode] += xferd; pp->joblen += xferd; if (pp->msg != NULL) { unx_addr = (caddr_t)pp->msg->b_wptr - unx_len; } else { unx_addr = pp->ioblock + (pp->xfercnt - unx_len); } } } /* Following code is common for PIO and DMA modes */ ecpp_putback_untransfered(pp, (caddr_t)unx_addr, unx_len); if (pp->msg != NULL) { freemsg(pp->msg); pp->msg = NULL; } /* mark the error status structure */ pp->timeout_error = 1; pp->e_busy = ECPP_ERR; fifo_timer_id = pp->fifo_timer_id; pp->fifo_timer_id = 0; qenable(pp->writeq); mutex_exit(&pp->umutex); if (fifo_timer_id) { (void) untimeout(fifo_timer_id); } } static void ecpp_putback_untransfered(struct ecppunit *pp, void *startp, uint_t len) { mblk_t *new_mp; ecpp_error(pp->dip, "ecpp_putback_untrans=%d\n", len); if (len == 0) { return; } new_mp = allocb(len, BPRI_MED); if (new_mp == NULL) { ecpp_error(pp->dip, "ecpp_putback_untransfered: allocb FAILURE.\n"); return; } bcopy(startp, new_mp->b_rptr, len); new_mp->b_wptr = new_mp->b_rptr + len; if (!putbq(pp->writeq, new_mp)) { freemsg(new_mp); } } static uchar_t ecr_write(struct ecppunit *pp, uint8_t ecr_byte) { int i, current_ecr; for (i = ECPP_REG_WRITE_MAX_LOOP; i > 0; i--) { ECR_WRITE(pp, ecr_byte); current_ecr = ECR_READ(pp); /* mask off the lower two read-only bits */ if ((ecr_byte & 0xFC) == (current_ecr & 0xFC)) return (SUCCESS); } return (FAILURE); } static uchar_t dcr_write(struct ecppunit *pp, uint8_t dcr_byte) { uint8_t current_dcr; int i; for (i = ECPP_REG_WRITE_MAX_LOOP; i > 0; i--) { DCR_WRITE(pp, dcr_byte); current_dcr = DCR_READ(pp); /* compare only bits 0-4 (direction bit return 1) */ if ((dcr_byte & 0x1F) == (current_dcr & 0x1F)) return (SUCCESS); } ecpp_error(pp->dip, "(%d)dcr_write: dcr written =%x, dcr readback =%x\n", i, dcr_byte, current_dcr); return (FAILURE); } static uchar_t ecpp_reset_port_regs(struct ecppunit *pp) { DCR_WRITE(pp, ECPP_SLCTIN | ECPP_nINIT); ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV); return (SUCCESS); } /* * The data transferred by the DMA engine goes through the FIFO, * so that when the DMA counter reaches zero (and an interrupt occurs) * the FIFO can still contain data. If this is the case, the ISR will * schedule this callback to wait until the FIFO drains or a timeout occurs. */ static void ecpp_fifo_timer(void *arg) { struct ecppunit *pp = arg; uint8_t ecr; timeout_id_t timeout_id; mutex_enter(&pp->umutex); /* * If the FIFO timer has been turned off, exit. */ if (pp->fifo_timer_id == 0) { ecpp_error(pp->dip, "ecpp_fifo_timer: untimedout\n"); mutex_exit(&pp->umutex); return; } else { pp->fifo_timer_id = 0; } /* * If the FIFO is not empty restart timer. Wait FIFO_DRAIN_PERIOD * (250 ms) and check FIFO_EMPTY bit again. Repeat until FIFO is * empty or until 10 * FIFO_DRAIN_PERIOD expires. */ ecr = ECR_READ(pp); if ((pp->current_mode != ECPP_DIAG_MODE) && (((ecr & ECPP_FIFO_EMPTY) == 0) && (pp->ecpp_drain_counter < 10))) { ecpp_error(pp->dip, "ecpp_fifo_timer(%d):FIFO not empty:ecr=%x\n", pp->ecpp_drain_counter, ecr); pp->fifo_timer_id = timeout(ecpp_fifo_timer, (caddr_t)pp, drv_usectohz(FIFO_DRAIN_PERIOD)); ++pp->ecpp_drain_counter; mutex_exit(&pp->umutex); return; } if (pp->current_mode != ECPP_DIAG_MODE) { /* * If the FIFO won't drain after 10 FIFO_DRAIN_PERIODs * then don't wait any longer. Simply clean up the transfer. */ if (pp->ecpp_drain_counter >= 10) { ecpp_error(pp->dip, "ecpp_fifo_timer(%d):" " clearing FIFO,can't wait:ecr=%x\n", pp->ecpp_drain_counter, ecr); } else { ecpp_error(pp->dip, "ecpp_fifo_timer(%d):FIFO empty:ecr=%x\n", pp->ecpp_drain_counter, ecr); } pp->ecpp_drain_counter = 0; } /* * Main section of routine: * - stop the DMA transfer timer * - program DMA with next cookie/window or unbind the DMA mapping * - update stats * - if last mblk in queue, signal to close() & return to idle state */ /* Stop the DMA transfer timeout timer */ timeout_id = pp->timeout_id; pp->timeout_id = 0; /* data has drained from fifo, it is ok to free dma resource */ if (pp->current_mode == ECPP_ECP_MODE || pp->current_mode == ECPP_DIAG_MODE || COMPAT_DMA(pp)) { off_t off; size_t len; /* update residual */ pp->resid -= pp->dma_cookie.dmac_size; /* update statistics */ pp->joblen += pp->dma_cookie.dmac_size; if (pp->dma_dir == DDI_DMA_WRITE) { pp->obytes[pp->current_mode] += pp->dma_cookie.dmac_size; } else { pp->ibytes[pp->current_mode] += pp->dma_cookie.dmac_size; } /* * Look if any cookies/windows left */ if (--pp->dma_cookie_count > 0) { /* process the next cookie */ ddi_dma_nextcookie(pp->dma_handle, &pp->dma_cookie); } else if (pp->dma_curwin < pp->dma_nwin) { /* process the next window */ if (ddi_dma_getwin(pp->dma_handle, pp->dma_curwin, &off, &len, &pp->dma_cookie, &pp->dma_cookie_count) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecpp_fifo_timer: ddi_dma_getwin failed\n"); goto dma_done; } pp->dma_curwin++; } else { goto dma_done; } ecpp_error(pp->dip, "ecpp_fifo_timer: next addr=%llx len=%d\n", pp->dma_cookie.dmac_address, pp->dma_cookie.dmac_size); /* kick off new transfer */ if (ECPP_DMA_START(pp) != SUCCESS) { ecpp_error(pp->dip, "ecpp_fifo_timer: dma_start failed\n"); goto dma_done; } (void) ecr_write(pp, (ecr & 0xe0) | ECPP_DMA_ENABLE | ECPP_INTR_MASK); mutex_exit(&pp->umutex); if (timeout_id) { (void) untimeout(timeout_id); } return; dma_done: if (ddi_dma_unbind_handle(pp->dma_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecpp_fifo_timer: unbind failed\n"); } else { ecpp_error(pp->dip, "ecpp_fifo_timer: unbind ok\n"); } } /* * if we did not use the dmablock, the mblk that * was used should be freed. */ if (pp->msg != NULL) { freemsg(pp->msg); pp->msg = NULL; } /* The port is no longer active */ pp->e_busy = ECPP_IDLE; qenable(pp->writeq); mutex_exit(&pp->umutex); if (timeout_id) { (void) untimeout(timeout_id); } } /* * In Compatibility mode, check if the peripheral is ready to accept data */ static uint8_t ecpp_check_status(struct ecppunit *pp) { uint8_t dsr; uint8_t statmask; if (pp->current_mode == ECPP_ECP_MODE || pp->current_mode == ECPP_DIAG_MODE) return (SUCCESS); statmask = ECPP_nERR | ECPP_SLCT | ECPP_nBUSY | ECPP_nACK; dsr = DSR_READ(pp); if ((dsr & ECPP_PE) || ((dsr & statmask) != statmask)) { pp->e_busy = ECPP_ERR; return (FAILURE); } else { return (SUCCESS); } } /* * if the peripheral is not ready to accept data, write service routine * periodically reschedules itself to recheck peripheral status * and start data transfer as soon as possible */ static void ecpp_wsrv_timer(void *arg) { struct ecppunit *pp = arg; ecpp_error(pp->dip, "ecpp_wsrv_timer: starting\n"); mutex_enter(&pp->umutex); if (pp->wsrv_timer_id == 0) { mutex_exit(&pp->umutex); return; } else { pp->wsrv_timer_id = 0; } ecpp_error(pp->dip, "ecpp_wsrv_timer: qenabling...\n"); qenable(pp->writeq); mutex_exit(&pp->umutex); } /* * Allocate a message indicating a backchannel request * and put it on the write queue */ static int ecpp_backchan_req(struct ecppunit *pp) { mblk_t *mp; if ((mp = allocb(sizeof (int), BPRI_MED)) == NULL) { ecpp_error(pp->dip, "ecpp_backchan_req: allocb failed\n"); return (FAILURE); } else { mp->b_datap->db_type = M_CTL; *(int *)mp->b_rptr = ECPP_BACKCHANNEL; mp->b_wptr = mp->b_rptr + sizeof (int); if (!putbq(pp->writeq, mp)) { ecpp_error(pp->dip, "ecpp_backchan_req:putbq failed\n"); freemsg(mp); return (FAILURE); } return (SUCCESS); } } /* * Cancel the function scheduled with timeout(9F) * This function is to be called with the mutex held */ static void ecpp_untimeout_unblock(struct ecppunit *pp, timeout_id_t *id) { timeout_id_t saved_id; ASSERT(mutex_owned(&pp->umutex)); if (*id) { saved_id = *id; *id = 0; mutex_exit(&pp->umutex); (void) untimeout(saved_id); mutex_enter(&pp->umutex); } } /* * get prnio interface capabilities */ static uint_t ecpp_get_prn_ifcap(struct ecppunit *pp) { uint_t ifcap; ifcap = PRN_1284_DEVID | PRN_TIMEOUTS | PRN_STREAMS; /* status (DSR) only makes sense in Centronics & Compat modes */ if (pp->current_mode == ECPP_CENTRONICS || pp->current_mode == ECPP_COMPAT_MODE) { ifcap |= PRN_1284_STATUS; } else if (pp->current_mode == ECPP_NIBBLE_MODE || pp->current_mode == ECPP_ECP_MODE) { ifcap |= PRN_BIDI; } return (ifcap); } /* * Determine SuperI/O type */ static struct ecpp_hw_bind * ecpp_determine_sio_type(struct ecppunit *pp) { struct ecpp_hw_bind *hw_bind; char *name; int i; name = ddi_binding_name(pp->dip); for (hw_bind = NULL, i = 0; i < NELEM(ecpp_hw_bind); i++) { if (strcmp(name, ecpp_hw_bind[i].name) == 0) { hw_bind = &ecpp_hw_bind[i]; break; } } return (hw_bind); } /* * * IEEE 1284 support routines: * negotiation and termination; * phase transitions; * device ID; * */ /* * Interface initialization, abnormal termination into Compatibility mode * * Peripheral may be non-1284, so we set current mode to ECPP_CENTRONICS */ static void ecpp_1284_init_interface(struct ecppunit *pp) { ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_001); /* * Toggle the nInit signal if configured in ecpp.conf * for most peripherals it is not needed */ if (pp->init_seq == TRUE) { DCR_WRITE(pp, ECPP_SLCTIN); drv_usecwait(50); /* T(ER) = 50us */ } DCR_WRITE(pp, ECPP_nINIT | ECPP_SLCTIN); pp->current_mode = pp->backchannel = ECPP_CENTRONICS; pp->current_phase = ECPP_PHASE_C_IDLE; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; ecpp_error(pp->dip, "ecpp_1284_init_interface: ok\n"); } /* * ECP mode negotiation */ static int ecp_negotiation(struct ecppunit *pp) { uint8_t dsr; /* ECP mode negotiation */ if (ecpp_1284_negotiation(pp, ECPP_XREQ_ECP, &dsr) == FAILURE) return (FAILURE); /* Event 5: peripheral deasserts PError and Busy, asserts Select */ if ((dsr & (ECPP_PE | ECPP_nBUSY | ECPP_SLCT)) != (ECPP_nBUSY | ECPP_SLCT)) { ecpp_error(pp->dip, "ecp_negotiation: failed event 5 %x\n", DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } /* entered Setup Phase */ pp->current_phase = ECPP_PHASE_ECP_SETUP; /* Event 30: host asserts nAutoFd */ DCR_WRITE(pp, ECPP_nINIT | ECPP_AFX); /* Event 31: peripheral asserts PError */ if (wait_dsr(pp, ECPP_PE, ECPP_PE, 35000) < 0) { ecpp_error(pp->dip, "ecp_negotiation: failed event 31 %x\n", DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } /* entered Forward Idle Phase */ pp->current_phase = ECPP_PHASE_ECP_FWD_IDLE; /* successful negotiation into ECP mode */ pp->current_mode = ECPP_ECP_MODE; pp->backchannel = ECPP_ECP_MODE; ecpp_error(pp->dip, "ecp_negotiation: ok\n"); return (SUCCESS); } /* * Nibble mode negotiation */ static int nibble_negotiation(struct ecppunit *pp) { uint8_t dsr; if (ecpp_1284_negotiation(pp, ECPP_XREQ_NIBBLE, &dsr) == FAILURE) { return (FAILURE); } /* * If peripheral has data available, PE and nErr will * be set low at Event 5 & 6. */ if ((dsr & (ECPP_PE | ECPP_nERR)) == 0) { pp->current_phase = ECPP_PHASE_NIBT_AVAIL; } else { pp->current_phase = ECPP_PHASE_NIBT_NAVAIL; } /* successful negotiation into Nibble mode */ pp->current_mode = ECPP_NIBBLE_MODE; pp->backchannel = ECPP_NIBBLE_MODE; ecpp_error(pp->dip, "nibble_negotiation: ok (phase=%x)\n", pp->current_phase); return (SUCCESS); } /* * Wait ptimeout usec for periph to set 'mask' bits to 'val' state * * return value < 0 indicates timeout */ static int wait_dsr(struct ecppunit *pp, uint8_t mask, uint8_t val, int ptimeout) { while (((DSR_READ(pp) & mask) != val) && ptimeout--) { drv_usecwait(1); } return (ptimeout); } /* * 1284 negotiation Events 0..6 * required mode is indicated by extensibility request value * * After successful negotiation SUCCESS is returned and * current mode is set according to xreq, * otherwise FAILURE is returned and current mode is set to * either COMPAT (1284 periph) or CENTRONICS (non-1284 periph) * * Current phase must be set by the caller (mode-specific negotiation) * * If rdsr is not NULL, DSR value after Event 6 is stored here */ static int ecpp_1284_negotiation(struct ecppunit *pp, uint8_t xreq, uint8_t *rdsr) { int xflag; ecpp_error(pp->dip, "nego(%x): entering...\n", xreq); /* negotiation should start in Compatibility mode */ (void) ecpp_1284_termination(pp); /* Set host into Compat mode */ ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_001); pp->current_phase = ECPP_PHASE_NEGO; /* Event 0: host sets extensibility request on data lines */ DATAR_WRITE(pp, xreq); /* Event 1: host deassert nSelectin and assert nAutoFd */ DCR_WRITE(pp, ECPP_nINIT | ECPP_AFX); drv_usecwait(1); /* Tp(ecp) == 0.5us */ /* * Event 2: peripheral asserts nAck, deasserts nFault, * asserts Select, asserts PError */ if (wait_dsr(pp, ECPP_nERR | ECPP_SLCT | ECPP_PE | ECPP_nACK, ECPP_nERR | ECPP_SLCT | ECPP_PE, 35000) < 0) { /* peripheral is not 1284-compliant */ ecpp_error(pp->dip, "nego(%x): failed event 2 %x\n", xreq, DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } /* * Event 3: host asserts nStrobe, latching extensibility value into * peripherals input latch. */ DCR_WRITE(pp, ECPP_nINIT | ECPP_AFX | ECPP_STB); drv_usecwait(2); /* Tp(ecp) = 0.5us */ /* * Event 4: hosts deasserts nStrobe and nAutoFD to acknowledge that * it has recognized an 1284 compatible peripheral */ DCR_WRITE(pp, ECPP_nINIT); /* * Event 5: Peripheral confirms it supports requested extension * For Nibble mode Xflag must be low, otherwise it must be high */ xflag = (xreq == ECPP_XREQ_NIBBLE) ? 0 : ECPP_SLCT; /* * Event 6: Peripheral sets nAck high * indicating that status lines are valid */ if (wait_dsr(pp, ECPP_nACK, ECPP_nACK, 35000) < 0) { /* Something wrong with peripheral */ ecpp_error(pp->dip, "nego(%x): failed event 6 %x\n", xreq, DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } if ((DSR_READ(pp) & ECPP_SLCT) != xflag) { /* Extensibility value is not supported */ ecpp_error(pp->dip, "nego(%x): failed event 5 %x\n", xreq, DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } if (rdsr) { *rdsr = DSR_READ(pp); } return (SUCCESS); } /* * 1284 Termination: Events 22..28 - set link to Compatibility mode * * This routine is not designed for Immediate termination, * caller must take care of waiting for a valid state, * (in particular, in ECP mode current phase must be Forward Idle) * otherwise interface will be reinitialized * * In case of Valid state termination SUCCESS is returned and * current_mode is ECPP_COMPAT_MODE, current phase is ECPP_PHASE_C_IDLE * Otherwise interface is reinitialized, FAILURE is returned and * current mode is ECPP_CENTRONICS, current phase is ECPP_PHASE_C_IDLE */ static int ecpp_1284_termination(struct ecppunit *pp) { int previous_mode = pp->current_mode; if (((pp->current_mode == ECPP_COMPAT_MODE || pp->current_mode == ECPP_CENTRONICS) && pp->current_phase == ECPP_PHASE_C_IDLE) || pp->current_mode == ECPP_DIAG_MODE) { ecpp_error(pp->dip, "termination: not needed\n"); return (SUCCESS); } /* Set host into Compat mode, interrupts disabled */ ECPP_MASK_INTR(pp); ECR_WRITE(pp, ECPP_INTR_SRV | ECPP_INTR_MASK | ECR_mode_001); pp->current_mode = ECPP_COMPAT_MODE; /* needed by next function */ ECPP_CONFIG_MODE(pp); /* * EPP mode uses simple nInit pulse for termination */ if (previous_mode == ECPP_EPP_MODE) { /* Event 68: host sets nInit low */ DCR_WRITE(pp, 0); drv_usecwait(55); /* T(ER) = 50us */ /* Event 69: host sets nInit high */ DCR_WRITE(pp, ECPP_nINIT | ECPP_SLCTIN); goto endterm; } /* terminate peripheral to Compat mode */ pp->current_phase = ECPP_PHASE_TERM; /* Event 22: hosts sets nSelectIn low and nAutoFd high */ DCR_WRITE(pp, ECPP_nINIT | ECPP_SLCTIN); /* Event 23: peripheral deasserts nFault and nBusy */ /* Event 24: peripheral asserts nAck */ if (wait_dsr(pp, ECPP_nERR | ECPP_nBUSY | ECPP_nACK, ECPP_nERR, 35000) < 0) { ecpp_error(pp->dip, "termination: failed events 23,24 %x\n", DSR_READ(pp)); ecpp_1284_init_interface(pp); return (FAILURE); } drv_usecwait(1); /* Tp = 0.5us */ /* Event 25: hosts sets nAutoFd low */ DCR_WRITE(pp, ECPP_nINIT | ECPP_SLCTIN | ECPP_AFX); /* Event 26: the peripheral puts itself in Compatible mode */ /* Event 27: peripheral deasserts nAck */ if (wait_dsr(pp, ECPP_nACK, ECPP_nACK, 35000) < 0) { ecpp_error(pp->dip, "termination: failed event 27 %x\n", DSR_READ(pp)); ecpp_1284_init_interface(pp); return (FAILURE); } drv_usecwait(1); /* Tp = 0.5us */ /* Event 28: hosts deasserts nAutoFd */ DCR_WRITE(pp, ECPP_nINIT | ECPP_SLCTIN); drv_usecwait(1); /* Tp = 0.5us */ endterm: /* Compatible mode Idle Phase */ pp->current_phase = ECPP_PHASE_C_IDLE; ecpp_error(pp->dip, "termination: completed %x %x\n", DSR_READ(pp), DCR_READ(pp)); return (SUCCESS); } /* * Initiate ECP backchannel DMA transfer */ static uchar_t ecp_peripheral2host(struct ecppunit *pp) { mblk_t *mp = NULL; size_t len; uint32_t xfer_time; ASSERT(pp->current_mode == ECPP_ECP_MODE && pp->current_phase == ECPP_PHASE_ECP_REV_IDLE); /* * hardware generates cycles to receive data from the peripheral * we only need to read from FIFO */ /* * If user issued read(2) of rev_resid bytes, xfer exactly this amount * unless it exceeds ECP_REV_BLKSZ_MAX; otherwise try to read * ECP_REV_BLKSZ_MAX or at least ECP_REV_BLKSZ bytes */ if (pp->nread > 0) { len = min(pp->nread, ECP_REV_BLKSZ_MAX); } else { len = ECP_REV_BLKSZ_MAX; } pp->nread = 0; /* clear after use */ /* * Allocate mblk for data, make max 2 attepmts: * if len bytes block fails, try our block size */ while ((mp = allocb(len, BPRI_MED)) == NULL) { ecpp_error(pp->dip, "ecp_periph2host: failed allocb(%d)\n", len); if (len > ECP_REV_BLKSZ) { len = ECP_REV_BLKSZ; } else { break; } } if (mp == NULL) { goto fail; } pp->msg = mp; pp->e_busy = ECPP_BUSY; pp->dma_dir = DDI_DMA_READ; pp->current_phase = ECPP_PHASE_ECP_REV_XFER; if (ecpp_init_dma_xfer(pp, (caddr_t)mp->b_rptr, len) == FAILURE) { goto fail; } /* * there are two problems with defining ECP backchannel xfer timeout * * a) IEEE 1284 allows infinite time between backchannel bytes, * but we must stop at some point to send the data upstream, * look if any forward transfer requests are pending, etc; * all that done, we can continue with backchannel data; * * b) we don`t know how much data peripheral has; * DMA counter is set to our buffer size, which can be bigger * than needed - in this case a timeout must detect this; * * The timeout we schedule here serves as both the transfer timeout * and a means of detecting backchannel stalls; in fact, there are * two timeouts in one: * * - transfer timeout is based on the ECP bandwidth of ~1MB/sec and * equals the time needed to transfer the whole buffer * (but not less than ECP_REV_MINTOUT ms); if it occurs, * DMA is stopped and the data is sent upstream; * * - backchannel watchdog, which would look at DMA counter * every rev_watchdog ms and stop the transfer only * if the counter hasn`t changed since the last time; * otherwise it would save DMA counter value and restart itself; * * transfer timeout is a multiple of rev_watchdog * and implemented as a downward counter * * on Grover, we can`t access DMAC registers while DMA is in flight, * so we can`t have watchdog on Grover, only timeout */ /* calculate number of watchdog invocations equal to the xfer timeout */ xfer_time = max((1000 * len) / pp->ecp_rev_speed, ECP_REV_MINTOUT); #if defined(__x86) pp->rev_timeout_cnt = (pp->hw == &x86) ? 1 : max(xfer_time / pp->rev_watchdog, 1); #else pp->rev_timeout_cnt = (pp->hw == &m1553) ? 1 : max(xfer_time / pp->rev_watchdog, 1); #endif pp->last_dmacnt = len; /* nothing xferred yet */ pp->timeout_id = timeout(ecpp_ecp_read_timeout, (caddr_t)pp, drv_usectohz(pp->rev_watchdog * 1000)); ecpp_error(pp->dip, "ecp_periph2host: DMA started len=%d\n" "xfer_time=%d wdog=%d cnt=%d\n", len, xfer_time, pp->rev_watchdog, pp->rev_timeout_cnt); return (SUCCESS); fail: if (mp) { freemsg(mp); } pp->e_busy = ECPP_IDLE; pp->current_phase = ECPP_PHASE_ECP_REV_IDLE; return (FAILURE); } /* * ECP backchannel read timeout * implements both backchannel watchdog and transfer timeout in ECP mode * if the transfer is still in progress, reschedule itself, * otherwise call completion routine */ static void ecpp_ecp_read_timeout(void *arg) { struct ecppunit *pp = arg; size_t dmacnt; mutex_enter(&pp->umutex); if (pp->timeout_id == 0) { mutex_exit(&pp->umutex); return; } else { pp->timeout_id = 0; } if (--pp->rev_timeout_cnt == 0) { /* * Transfer timed out */ ecpp_error(pp->dip, "ecp_read_timeout: timeout\n"); pp->xfer_tout++; ecpp_ecp_read_completion(pp); } else { /* * Backchannel watchdog: * look if DMA made any progress from the last time */ dmacnt = ECPP_DMA_GETCNT(pp); if (dmacnt - pp->last_dmacnt == 0) { /* * No progress - stop the transfer and send * whatever has been read so far up the stream */ ecpp_error(pp->dip, "ecp_read_timeout: no progress\n"); pp->xfer_tout++; ecpp_ecp_read_completion(pp); } else { /* * Something was transferred - restart ourselves */ ecpp_error(pp->dip, "ecp_read_timeout: restarting\n"); pp->last_dmacnt = dmacnt; pp->timeout_id = timeout(ecpp_ecp_read_timeout, (caddr_t)pp, drv_usectohz(pp->rev_watchdog * 1000)); } } mutex_exit(&pp->umutex); } /* * ECP backchannel read completion: * stop the DMA, free DMA resources and send read data upstream */ static void ecpp_ecp_read_completion(struct ecppunit *pp) { size_t xfer_len, unx_len; mblk_t *mp; ASSERT(mutex_owned(&pp->umutex)); ASSERT(pp->current_mode == ECPP_ECP_MODE && pp->current_phase == ECPP_PHASE_ECP_REV_XFER); ASSERT(pp->msg != NULL); /* * Stop the transfer and unbind DMA handle */ if (ECPP_DMA_STOP(pp, &unx_len) == FAILURE) { unx_len = pp->resid; ecpp_error(pp->dip, "ecp_read_completion: failed dma_stop\n"); } mp = pp->msg; xfer_len = pp->resid - unx_len; /* how much data was transferred */ if (ddi_dma_unbind_handle(pp->dma_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "ecp_read_completion: unbind failed.\n"); } ecpp_error(pp->dip, "ecp_read_completion: xfered %d bytes of %d\n", xfer_len, pp->resid); /* clean up and update statistics */ pp->msg = NULL; pp->resid -= xfer_len; pp->ibytes[pp->current_mode] += xfer_len; pp->e_busy = ECPP_IDLE; pp->current_phase = ECPP_PHASE_ECP_REV_IDLE; /* * Send the read data up the stream */ mp->b_wptr += xfer_len; if (canputnext(pp->readq)) { mutex_exit(&pp->umutex); putnext(pp->readq, mp); mutex_enter(&pp->umutex); } else { ecpp_error(pp->dip, "ecp_read_completion: fail canputnext\n"); if (!putq(pp->readq, mp)) { freemsg(mp); } } /* if bytes left in the FIFO another transfer is needed */ if (!(ECR_READ(pp) & ECPP_FIFO_EMPTY)) { (void) ecpp_backchan_req(pp); } qenable(pp->writeq); } /* * Read one byte in the Nibble mode */ static uchar_t nibble_peripheral2host(struct ecppunit *pp, uint8_t *byte) { uint8_t n[2]; /* two nibbles */ int i; /* * One byte is made of two nibbles */ for (i = 0; i < 2; i++) { /* Event 7, 12: host asserts nAutoFd to move to read a nibble */ DCR_WRITE(pp, ECPP_nINIT | ECPP_AFX); /* Event 8: peripheral puts data on the status lines */ /* Event 9: peripheral asserts nAck, data available */ if (wait_dsr(pp, ECPP_nACK, 0, 35000) < 0) { ecpp_error(pp->dip, "nibble_periph2host(%d): failed event 9 %x\n", i + 1, DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } n[i] = DSR_READ(pp); /* get a nibble */ /* Event 10: host deasserts nAutoFd to say it grabbed data */ DCR_WRITE(pp, ECPP_nINIT); /* (2) Event 13: peripheral asserts PE - end of data phase */ /* Event 11: peripheral deasserts nAck to finish handshake */ if (wait_dsr(pp, ECPP_nACK, ECPP_nACK, 35000) < 0) { ecpp_error(pp->dip, "nibble_periph2host(%d): failed event 11 %x\n", i + 1, DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } } /* extract data byte from two nibbles - optimized formula */ *byte = ((((n[1] & ~ECPP_nACK) << 1) | (~n[1] & ECPP_nBUSY)) & 0xf0) | ((((n[0] & ~ECPP_nACK) >> 3) | ((~n[0] & ECPP_nBUSY) >> 4)) & 0x0f); pp->ibytes[ECPP_NIBBLE_MODE]++; return (SUCCESS); } /* * process data transfers requested by the peripheral */ static uint_t ecpp_peripheral2host(struct ecppunit *pp) { if (!canputnext(pp->readq)) { ecpp_error(pp->dip, "ecpp_peripheral2host: readq full\n"); return (SUCCESS); } switch (pp->backchannel) { case ECPP_CENTRONICS: /* no backchannel */ return (SUCCESS); case ECPP_NIBBLE_MODE: ASSERT(pp->current_mode == ECPP_NIBBLE_MODE); /* * Event 20: Host sets nAutoFd high to ack request */ DCR_WRITE(pp, ECPP_nINIT); /* Event 21: Periph sets PError low to ack host */ if (wait_dsr(pp, ECPP_PE, 0, 35000) < 0) { ecpp_error(pp->dip, "ecpp_periph2host: failed event 21 %x\n", DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } pp->current_phase = ECPP_PHASE_NIBT_AVAIL; /* this routine will read the data in Nibble mode */ return (ecpp_idle_phase(pp)); case ECPP_ECP_MODE: if ((pp->current_phase == ECPP_PHASE_ECP_FWD_IDLE) && (ecp_forward2reverse(pp) == FAILURE)) { return (FAILURE); } return (ecp_peripheral2host(pp)); /* start the transfer */ case ECPP_DIAG_MODE: { mblk_t *mp; int i; if (ECR_READ(pp) & ECPP_FIFO_EMPTY) { ecpp_error(pp->dip, "ecpp_periph2host: fifo empty\n"); return (SUCCESS); } /* allocate the FIFO size */ if ((mp = allocb(ECPP_FIFO_SZ, BPRI_MED)) == NULL) { ecpp_error(pp->dip, "ecpp_periph2host: allocb FAILURE.\n"); return (FAILURE); } /* * For the time being just read it byte by byte */ i = ECPP_FIFO_SZ; while (i-- && (!(ECR_READ(pp) & ECPP_FIFO_EMPTY))) { *mp->b_wptr++ = TFIFO_READ(pp); drv_usecwait(1); /* ECR is sometimes slow to update */ } if (canputnext(pp->readq)) { mutex_exit(&pp->umutex); mp->b_datap->db_type = M_DATA; ecpp_error(pp->dip, "ecpp_periph2host: sending %d bytes\n", mp->b_wptr - mp->b_rptr); putnext(pp->readq, mp); mutex_enter(&pp->umutex); return (SUCCESS); } else { ecpp_error(pp->dip, "ecpp_periph2host: !canputnext data lost\n"); freemsg(mp); return (FAILURE); } } default: ecpp_error(pp->dip, "ecpp_peripheraltohost: illegal back"); return (FAILURE); } } /* * Negotiate from ECP Forward Idle to Reverse Idle Phase * * (manipulations with dcr/ecr are according to ECP Specification) */ static int ecp_forward2reverse(struct ecppunit *pp) { ASSERT(pp->current_mode == ECPP_ECP_MODE && pp->current_phase == ECPP_PHASE_ECP_FWD_IDLE); /* place port into PS2 mode */ ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_SRV | ECPP_INTR_MASK); /* set direction bit (DCR3-0 must be 0100 - National) */ DCR_WRITE(pp, ECPP_REV_DIR | ECPP_nINIT); /* enable hardware assist */ ECR_WRITE(pp, ECR_mode_011 | ECPP_INTR_SRV | ECPP_INTR_MASK); drv_usecwait(1); /* Tp(ecp) = 0.5us */ /* Event 39: host sets nInit low */ DCR_WRITE(pp, ECPP_REV_DIR); /* Event 40: peripheral sets PError low */ pp->current_phase = ECPP_PHASE_ECP_REV_IDLE; ecpp_error(pp->dip, "ecp_forward2reverse ok\n"); return (SUCCESS); } /* * Negotiate from ECP Reverse Idle to Forward Idle Phase * * (manipulations with dcr/ecr are according to ECP Specification) */ static int ecp_reverse2forward(struct ecppunit *pp) { ASSERT(pp->current_mode == ECPP_ECP_MODE && pp->current_phase == ECPP_PHASE_ECP_REV_IDLE); /* Event 47: host deasserts nInit */ DCR_WRITE(pp, ECPP_REV_DIR | ECPP_nINIT); /* * Event 48: peripheral deasserts nAck * Event 49: peripheral asserts PError */ if (wait_dsr(pp, ECPP_PE, ECPP_PE, 35000) < 0) { ecpp_error(pp->dip, "ecp_reverse2forward: failed event 49 %x\n", DSR_READ(pp)); (void) ecpp_1284_termination(pp); return (FAILURE); } /* place port into PS2 mode */ ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_SRV | ECPP_INTR_MASK); /* clear direction bit */ DCR_WRITE(pp, ECPP_nINIT); /* reenable hardware assist */ ECR_WRITE(pp, ECR_mode_011 | ECPP_INTR_SRV | ECPP_INTR_MASK); pp->current_phase = ECPP_PHASE_ECP_FWD_IDLE; ecpp_error(pp->dip, "ecp_reverse2forward ok\n"); return (SUCCESS); } /* * Default negotiation chooses the best mode supported by peripheral * Note that backchannel mode may be different from forward mode */ static void ecpp_default_negotiation(struct ecppunit *pp) { if (!noecp && (ecpp_mode_negotiation(pp, ECPP_ECP_MODE) == SUCCESS)) { /* 1284 compatible device */ pp->io_mode = (pp->fast_compat == TRUE) ? ECPP_DMA : ECPP_PIO; return; } else if (ecpp_mode_negotiation(pp, ECPP_NIBBLE_MODE) == SUCCESS) { /* 1284 compatible device */ pp->io_mode = (pp->fast_compat == TRUE) ? ECPP_DMA : ECPP_PIO; } else { /* Centronics device */ pp->io_mode = (pp->fast_centronics == TRUE) ? ECPP_DMA : ECPP_PIO; } ECPP_CONFIG_MODE(pp); } /* * Negotiate to the mode indicated by newmode */ static int ecpp_mode_negotiation(struct ecppunit *pp, uchar_t newmode) { /* any other mode is impossible */ ASSERT(pp->current_mode == ECPP_CENTRONICS || pp->current_mode == ECPP_COMPAT_MODE || pp->current_mode == ECPP_NIBBLE_MODE || pp->current_mode == ECPP_ECP_MODE || pp->current_mode == ECPP_DIAG_MODE); if (pp->current_mode == newmode) { return (SUCCESS); } /* termination from ECP is only allowed from the Forward Idle Phase */ if ((pp->current_mode == ECPP_ECP_MODE) && (pp->current_phase != ECPP_PHASE_ECP_FWD_IDLE)) { /* this may break into Centronics */ (void) ecp_reverse2forward(pp); } switch (newmode) { case ECPP_CENTRONICS: (void) ecpp_1284_termination(pp); /* put superio into PIO mode */ ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV); pp->current_mode = ECPP_CENTRONICS; pp->backchannel = ECPP_CENTRONICS; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); case ECPP_COMPAT_MODE: /* ECPP_COMPAT_MODE should support Nibble as a backchannel */ if (pp->current_mode == ECPP_NIBBLE_MODE) { if (ecpp_1284_termination(pp) == SUCCESS) { pp->current_mode = ECPP_COMPAT_MODE; pp->backchannel = ECPP_NIBBLE_MODE; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); } else { return (FAILURE); } } if ((nibble_negotiation(pp) == SUCCESS) && (ecpp_1284_termination(pp) == SUCCESS)) { pp->backchannel = ECPP_NIBBLE_MODE; pp->current_mode = ECPP_COMPAT_MODE; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); } else { return (FAILURE); } case ECPP_NIBBLE_MODE: if (nibble_negotiation(pp) == FAILURE) { return (FAILURE); } pp->backchannel = ECPP_NIBBLE_MODE; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); case ECPP_ECP_MODE: if (pp->noecpregs) return (FAILURE); if (ecp_negotiation(pp) == FAILURE) { return (FAILURE); } /* * National says CTR[3:0] should be 0100b before moving to 011 */ DCR_WRITE(pp, ECPP_nINIT); if (ecr_write(pp, ECR_mode_011 | ECPP_INTR_MASK | ECPP_INTR_SRV) == FAILURE) { ecpp_error(pp->dip, "mode_nego:ECP: failed w/ecr\n"); return (FAILURE); } ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); case ECPP_DIAG_MODE: /* * In DIAG mode application can do nasty things(e.g drive pins) * To keep peripheral sane, terminate to Compatibility mode */ (void) ecpp_1284_termination(pp); /* put superio into TFIFO mode */ if (ecr_write(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV) == FAILURE) { ecpp_error(pp->dip, "put to TFIFO: failed w/ecr\n"); return (FAILURE); } pp->current_mode = ECPP_DIAG_MODE; pp->backchannel = ECPP_DIAG_MODE; ECPP_CONFIG_MODE(pp); pp->to_mode[pp->current_mode]++; return (SUCCESS); default: ecpp_error(pp->dip, "ecpp_mode_negotiation: mode %d not supported\n", newmode); return (FAILURE); } } /* * Standard (9.1): Peripheral data is available only when the host places * the interface in a mode capable of peripheral-to-host data transfer. * This requires the host periodically to place the interface in such a mode. * Polling can be eliminated by leaving the interface in an 1284 idle phase. */ static uchar_t ecpp_idle_phase(struct ecppunit *pp) { uchar_t rval = FAILURE; /* * If there is no space on the read queue, do not reverse channel */ if (!canputnext(pp->readq)) { ecpp_error(pp->dip, "ecpp_idle_phase: readq full\n"); return (SUCCESS); } switch (pp->backchannel) { case ECPP_CENTRONICS: case ECPP_COMPAT_MODE: case ECPP_DIAG_MODE: /* nothing */ ecpp_error(pp->dip, "ecpp_idle_phase: compat idle\n"); return (SUCCESS); case ECPP_NIBBLE_MODE: /* * read as much data as possible, ending up in either * Reverse Idle or Host Busy Data Available phase */ ecpp_error(pp->dip, "ecpp_idle_phase: nibble backchannel\n"); if ((pp->current_mode != ECPP_NIBBLE_MODE) && (ecpp_mode_negotiation(pp, ECPP_NIBBLE_MODE) == FAILURE)) { break; } rval = read_nibble_backchan(pp); /* put interface into Reverse Idle phase */ if (pp->current_phase == ECPP_PHASE_NIBT_NAVAIL && canputnext(pp->readq)) { ecpp_error(pp->dip, "ecpp_idle_phase: going revidle\n"); /* * Event 7: host asserts nAutoFd * enable nAck interrupt to get a backchannel request */ DCR_WRITE(pp, ECPP_nINIT | ECPP_AFX | ECPP_INTR_EN); ECPP_UNMASK_INTR(pp); } break; case ECPP_ECP_MODE: /* * if data is already available, request the backchannel xfer * otherwise stay in Forward Idle and enable nErr interrupts */ ecpp_error(pp->dip, "ecpp_idle_phase: ECP forward\n"); ASSERT(pp->current_phase == ECPP_PHASE_ECP_FWD_IDLE || pp->current_phase == ECPP_PHASE_ECP_REV_IDLE); /* put interface into Forward Idle phase */ if ((pp->current_phase == ECPP_PHASE_ECP_REV_IDLE) && (ecp_reverse2forward(pp) == FAILURE)) { return (FAILURE); } /* * if data already available, put backchannel request on the wq * otherwise enable nErr interrupts */ if ((DSR_READ(pp) & ECPP_nERR) == 0) { (void) ecpp_backchan_req(pp); } else { ECR_WRITE(pp, ECR_READ(pp) & ~ECPP_INTR_MASK | ECPP_INTR_SRV); ECPP_UNMASK_INTR(pp); } return (SUCCESS); default: ecpp_error(pp->dip, "ecpp_idle_phase: illegal backchannel"); } return (rval); } /* * This routine will leave the port in ECPP_PHASE_NIBT_REVIDLE * Due to flow control, though, it may stop at ECPP_PHASE_NIBT_AVAIL, * and continue later as the user consumes data from the read queue * * The current phase should be NIBT_AVAIL or NIBT_NAVAIL * If some events fail during transfer, termination puts link * to Compatibility mode and FAILURE is returned */ static int read_nibble_backchan(struct ecppunit *pp) { mblk_t *mp; int i; int rval = SUCCESS; ASSERT(pp->current_mode == ECPP_NIBBLE_MODE); pp->current_phase = (DSR_READ(pp) & (ECPP_nERR | ECPP_PE)) ? ECPP_PHASE_NIBT_NAVAIL : ECPP_PHASE_NIBT_AVAIL; ecpp_error(pp->dip, "read_nibble_backchan: %x\n", DSR_READ(pp)); /* * While data is available, read it in NIBBLE_REV_BLKSZ byte chunks * and send up the stream */ while (pp->current_phase == ECPP_PHASE_NIBT_AVAIL && rval == SUCCESS) { /* see if there's space on the queue */ if (!canputnext(pp->readq)) { ecpp_error(pp->dip, "read_nibble_backchan: canputnext failed\n"); return (SUCCESS); } if ((mp = allocb(NIBBLE_REV_BLKSZ, BPRI_MED)) == NULL) { ecpp_error(pp->dip, "read_nibble_backchan: allocb failed\n"); return (SUCCESS); } /* read a chunk of data from the peripheral byte by byte */ i = NIBBLE_REV_BLKSZ; while (i-- && !(DSR_READ(pp) & ECPP_nERR)) { if (nibble_peripheral2host(pp, mp->b_wptr) != SUCCESS) { rval = FAILURE; break; } mp->b_wptr++; } pp->current_phase = (DSR_READ(pp) & (ECPP_nERR | ECPP_PE)) ? ECPP_PHASE_NIBT_NAVAIL : ECPP_PHASE_NIBT_AVAIL; if (mp->b_wptr - mp->b_rptr > 0) { ecpp_error(pp->dip, "read_nibble_backchan: sending %d bytes\n", mp->b_wptr - mp->b_rptr); pp->nread = 0; mutex_exit(&pp->umutex); putnext(pp->readq, mp); mutex_enter(&pp->umutex); } else { freemsg(mp); } } return (rval); } /* * 'Request Device ID using nibble mode' negotiation */ static int devidnib_negotiation(struct ecppunit *pp) { uint8_t dsr; if (ecpp_1284_negotiation(pp, ECPP_XREQ_NIBBLE | ECPP_XREQ_ID, &dsr) == FAILURE) { return (FAILURE); } /* * If peripheral has data available, PE and nErr will * be set low at Event 5 & 6. */ if ((dsr & (ECPP_PE | ECPP_nERR)) == 0) { pp->current_phase = ECPP_PHASE_NIBT_AVAIL; } else { pp->current_phase = ECPP_PHASE_NIBT_NAVAIL; } ecpp_error(pp->dip, "ecpp_devidnib_nego: current_phase=%x\n", pp->current_phase); /* successful negotiation into Nibble mode */ pp->current_mode = ECPP_NIBBLE_MODE; pp->backchannel = ECPP_NIBBLE_MODE; ecpp_error(pp->dip, "ecpp_devidnib_nego: ok\n"); return (SUCCESS); } /* * Read 1284 device ID sequence * * This function should be called two times: * 1) ecpp_getdevid(pp, NULL, &len) - to retrieve ID length; * 2) ecpp_getdevid(pp, buffer, &len) - to read len bytes into buffer * * After 2) port is in Compatible mode * If the caller fails to make second call, it must reset port to Centronics * */ static int ecpp_getdevid(struct ecppunit *pp, uint8_t *id, int *lenp, int mode) { uint8_t lenhi, lenlo; uint8_t dsr; int i; switch (mode) { case ECPP_NIBBLE_MODE: /* negotiate only if neccessary */ if ((pp->current_mode != mode) || (id == NULL)) { if (devidnib_negotiation(pp) == FAILURE) { return (EIO); } } if (pp->current_phase != ECPP_PHASE_NIBT_AVAIL) { return (EIO); } /* * Event 14: Host tristates data bus, peripheral * asserts nERR if data available, usually the * status bits (7-0) and requires two reads since * only nibbles are transfered. */ dsr = DSR_READ(pp); if (id == NULL) { /* * first two bytes are the length of the sequence * (incl. these bytes) * first byte is MSB */ if ((dsr & ECPP_nERR) || (nibble_peripheral2host(pp, &lenhi) == FAILURE) || (dsr & ECPP_nERR) || (nibble_peripheral2host(pp, &lenlo) == FAILURE)) { ecpp_error(pp->dip, "ecpp_getdevid: id length read error\n"); return (EIO); } *lenp = (lenhi << 8) | (lenlo); ecpp_error(pp->dip, "ecpp_getdevid: id length = %d\n", *lenp); if (*lenp < 2) { return (EIO); } } else { /* * read the rest of the data */ i = *lenp; while (i && ((dsr & ECPP_nERR) == 0)) { if (nibble_peripheral2host(pp, id++) == FAILURE) break; i--; dsr = DSR_READ(pp); } ecpp_error(pp->dip, "ecpp_getdevid: read %d bytes\n", *lenp - i); /* * 1284: After receiving the sequence, the host is * required to return the link to the Compatibility mode */ (void) ecpp_1284_termination(pp); } break; /* Other modes are not yet supported */ default: return (EINVAL); } return (0); } /* * Various hardware support * * First define some stubs for functions that do nothing */ /*ARGSUSED*/ static void empty_config_mode(struct ecppunit *pp) { } /*ARGSUSED*/ static void empty_mask_intr(struct ecppunit *pp) { } #if defined(__x86) static size_t x86_getcnt(struct ecppunit *pp) { int count; (void) ddi_dmae_getcnt(pp->dip, pp->uh.x86.chn, &count); return (count); } #endif /* * * National PC87332 and PC97317 SuperIOs support routines * These chips are used in PCI-based Darwin, Quark, Quasar, Excalibur * and use EBus DMA facilities (Cheerio or RIO) * */ static int pc87332_map_regs(struct ecppunit *pp) { if (ddi_regs_map_setup(pp->dip, 1, (caddr_t *)&pp->uh.ebus.c_reg, 0, sizeof (struct config_reg), &acc_attr, &pp->uh.ebus.c_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "pc87332_map_regs: failed c_reg\n"); goto fail; } if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->i_reg, 0, sizeof (struct info_reg), &acc_attr, &pp->i_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "pc87332_map_regs: failed i_reg\n"); goto fail; } if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->f_reg, 0x400, sizeof (struct fifo_reg), &acc_attr, &pp->f_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "pc87332_map_regs: failed f_reg\n"); goto fail; } if (ddi_regs_map_setup(pp->dip, 2, (caddr_t *)&pp->uh.ebus.dmac, 0, sizeof (struct cheerio_dma_reg), &acc_attr, &pp->uh.ebus.d_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "pc87332_map_regs: failed dmac\n"); goto fail; } return (SUCCESS); fail: pc87332_unmap_regs(pp); return (FAILURE); } static void pc87332_unmap_regs(struct ecppunit *pp) { if (pp->uh.ebus.c_handle) { ddi_regs_map_free(&pp->uh.ebus.c_handle); } if (pp->uh.ebus.d_handle) { ddi_regs_map_free(&pp->uh.ebus.d_handle); } if (pp->i_handle) { ddi_regs_map_free(&pp->i_handle); } if (pp->f_handle) { ddi_regs_map_free(&pp->f_handle); } } static uint8_t pc87332_read_config_reg(struct ecppunit *pp, uint8_t reg_num) { uint8_t retval; PP_PUTB(pp->uh.ebus.c_handle, &pp->uh.ebus.c_reg->index, reg_num); retval = PP_GETB(pp->uh.ebus.c_handle, &pp->uh.ebus.c_reg->data); return (retval); } static void pc87332_write_config_reg(struct ecppunit *pp, uint8_t reg_num, uint8_t val) { PP_PUTB(pp->uh.ebus.c_handle, &pp->uh.ebus.c_reg->index, reg_num); PP_PUTB(pp->uh.ebus.c_handle, &pp->uh.ebus.c_reg->data, val); /* * second write to this register is needed. the register behaves as * a fifo. the first value written goes to the data register. the * second write pushes the initial value to the register indexed. */ PP_PUTB(pp->uh.ebus.c_handle, &pp->uh.ebus.c_reg->data, val); } static int pc87332_config_chip(struct ecppunit *pp) { uint8_t pmc, fcr; pp->current_phase = ECPP_PHASE_INIT; /* ECP DMA configuration bit (PMC4) must be set */ pmc = pc87332_read_config_reg(pp, PMC); if (!(pmc & PC87332_PMC_ECP_DMA_CONFIG)) { pc87332_write_config_reg(pp, PMC, pmc | PC87332_PMC_ECP_DMA_CONFIG); } /* * The Parallel Port Multiplexor pins must be driven. * Check to see if FCR3 is zero, if not clear FCR3. */ fcr = pc87332_read_config_reg(pp, FCR); if (fcr & PC87332_FCR_PPM_FLOAT_CTL) { pc87332_write_config_reg(pp, FCR, fcr & ~PC87332_FCR_PPM_FLOAT_CTL); } /* * clear bits 3-0 in CTR (aka DCR) prior to enabling ECP mode * CTR5 can not be cleared in SPP mode, CTR5 will return 1. * "FAILURE" in this case is ok. Better to use dcr_write() * to ensure reliable writing to DCR. */ if (dcr_write(pp, ECPP_DCR_SET | ECPP_nINIT) == FAILURE) { ecpp_error(pp->dip, "ecpp_config_87332: DCR config\n"); } /* enable ECP mode, level intr (note that DCR bits 3-0 == 0x0) */ pc87332_write_config_reg(pp, PCR, PC87332_PCR_INTR_LEVL | PC87332_PCR_ECP_EN); /* put SuperIO in initial state */ if (ecr_write(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV) == FAILURE) { ecpp_error(pp->dip, "ecpp_config_87332: ECR\n"); } if (dcr_write(pp, ECPP_DCR_SET | ECPP_SLCTIN | ECPP_nINIT) == FAILURE) { ecpp_error(pp->dip, "ecpp_config_87332: w/DCR failed2.\n"); return (FAILURE); } /* we are in centronic mode */ pp->current_mode = ECPP_CENTRONICS; /* in compatible mode with no data transfer in progress */ pp->current_phase = ECPP_PHASE_C_IDLE; return (SUCCESS); } /* * A new mode was set, do some mode specific reconfiguration * in this case - set interrupt characteristic */ static void pc87332_config_mode(struct ecppunit *pp) { if (COMPAT_PIO(pp)) { pc87332_write_config_reg(pp, PCR, 0x04); } else { pc87332_write_config_reg(pp, PCR, 0x14); } } static int pc97317_map_regs(struct ecppunit *pp) { if (pc87332_map_regs(pp) != SUCCESS) { return (FAILURE); } if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->uh.ebus.c2_reg, 0x403, sizeof (struct config2_reg), &acc_attr, &pp->uh.ebus.c2_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "pc97317_map_regs: failed c2_reg\n"); pc87332_unmap_regs(pp); return (FAILURE); } else { return (SUCCESS); } } static void pc97317_unmap_regs(struct ecppunit *pp) { if (pp->uh.ebus.c2_handle) { ddi_regs_map_free(&pp->uh.ebus.c2_handle); } pc87332_unmap_regs(pp); } /* * OBP should configure the PC97317 such that it does not need further * configuration. Upon sustaining, it may be necessary to examine * or change the configuration registers. This routine is left in * the file for that purpose. */ static int pc97317_config_chip(struct ecppunit *pp) { uint8_t conreg; /* set the logical device name */ pc87332_write_config_reg(pp, PC97317_CONFIG_DEV_NO, 0x4); /* SPP Compatibility */ PP_PUTB(pp->uh.ebus.c2_handle, &pp->uh.ebus.c2_reg->eir, PC97317_CONFIG2_CONTROL2); PP_PUTB(pp->uh.ebus.c2_handle, &pp->uh.ebus.c2_reg->edr, 0x80); /* low interrupt polarity */ pc87332_write_config_reg(pp, PC97317_CONFIG_INTR_TYPE, 0x00); /* ECP mode */ pc87332_write_config_reg(pp, PC97317_CONFIG_PP_CONFIG, 0xf2); if (dcr_write(pp, ECPP_SLCTIN | ECPP_nINIT) == FAILURE) { ecpp_error(pp->dip, "pc97317_config_chip: failed w/DCR\n"); } if (ecr_write(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV) == FAILURE) { ecpp_error(pp->dip, "pc97317_config_chip: failed w/ECR\n"); } #ifdef DEBUG conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_DEV_NO); ecpp_error(pp->dip, "97317:conreg7(logical dev)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_BASE_ADDR_MSB); ecpp_error(pp->dip, "97317:conreg60(addrHi)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_BASE_ADDR_LSB); ecpp_error(pp->dip, "97317:conreg61(addrLo)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_INTR_SEL); ecpp_error(pp->dip, "97317:conreg70(IRQL)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_INTR_TYPE); ecpp_error(pp->dip, "97317:conreg71(intr type)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_ACTIVATE); ecpp_error(pp->dip, "97317:conreg30(Active)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_IO_RANGE); ecpp_error(pp->dip, "97317:conreg31(IO Range Check)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_DMA0_CHAN); ecpp_error(pp->dip, "97317:conreg74(DMA0 Chan)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_DMA1_CHAN); ecpp_error(pp->dip, "97317:conreg75(DMA1 Chan)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_PP_CONFIG); ecpp_error(pp->dip, "97317:conregFO(pport conf)=%x\n", conreg); conreg = pc87332_read_config_reg(pp, PC97317_CONFIG_PP_CONFIG); ecpp_error(pp->dip, "97317:conregFO(pport conf)=%x\n", conreg); #endif /* DEBUG */ return (SUCCESS); } /* * A new mode was set, do some mode specific reconfiguration * in this case - set interrupt polarity */ static void pc97317_config_mode(struct ecppunit *pp) { /* set the logical device name */ pc87332_write_config_reg(pp, PC97317_CONFIG_DEV_NO, 0x4); if (COMPAT_PIO(pp) || pp->current_mode == ECPP_NIBBLE_MODE) { pc87332_write_config_reg(pp, PC97317_CONFIG_INTR_TYPE, 0x02); } else { pc87332_write_config_reg(pp, PC97317_CONFIG_INTR_TYPE, 0x00); } } static void cheerio_mask_intr(struct ecppunit *pp) { /* mask Cheerio interrupts */ AND_SET_LONG_R(pp->uh.ebus.d_handle, &pp->uh.ebus.dmac->csr, ~DCSR_INT_EN); } static void cheerio_unmask_intr(struct ecppunit *pp) { /* unmask Cheerio interrupts */ OR_SET_LONG_R(pp->uh.ebus.d_handle, &pp->uh.ebus.dmac->csr, DCSR_INT_EN | DCSR_TCI_DIS); } static int cheerio_dma_start(struct ecppunit *pp) { cheerio_reset_dcsr(pp); SET_DMAC_BCR(pp, pp->dma_cookie.dmac_size); SET_DMAC_ACR(pp, pp->dma_cookie.dmac_address); if (pp->dma_dir == DDI_DMA_READ) { SET_DMAC_CSR(pp, DCSR_INT_EN | DCSR_EN_CNT | DCSR_EN_DMA | DCSR_CSR_DRAIN | DCSR_BURST_1 | DCSR_BURST_0 | DCSR_WRITE); } else { SET_DMAC_CSR(pp, DCSR_INT_EN | DCSR_EN_CNT | DCSR_EN_DMA | DCSR_CSR_DRAIN | DCSR_BURST_1 | DCSR_BURST_0); } return (SUCCESS); } /* * Note: BCR is reset to 0, so counter should always be read before dma_stop */ static int cheerio_dma_stop(struct ecppunit *pp, size_t *countp) { uint8_t ecr; /* disable DMA and byte counter */ AND_SET_LONG_R(pp->uh.ebus.d_handle, &pp->uh.ebus.dmac->csr, ~(DCSR_EN_DMA | DCSR_EN_CNT| DCSR_INT_EN)); /* ACK and disable the TC interrupt */ OR_SET_LONG_R(pp->uh.ebus.d_handle, &pp->uh.ebus.dmac->csr, DCSR_TC | DCSR_TCI_DIS); /* read DMA count if requested */ if (countp) { *countp = cheerio_getcnt(pp); } cheerio_reset_dcsr(pp); SET_DMAC_BCR(pp, 0); /* turn off SuperIO's DMA */ ecr = ECR_READ(pp); if (ecr_write(pp, ecr & ~ECPP_DMA_ENABLE) == FAILURE) { return (FAILURE); } /* Disable SuperIO interrupts and DMA */ ecr = ECR_READ(pp); return (ecr_write(pp, ecr | ECPP_INTR_SRV)); } static size_t cheerio_getcnt(struct ecppunit *pp) { return (GET_DMAC_BCR(pp)); } /* * Reset the DCSR by first setting the RESET bit to 1. Poll the * DCSR_CYC_PEND bit to make sure there are no more pending DMA cycles. * If there are no more pending cycles, clear the RESET bit. */ static void cheerio_reset_dcsr(struct ecppunit *pp) { int timeout = DMAC_RESET_TIMEOUT; SET_DMAC_CSR(pp, DCSR_RESET); while (GET_DMAC_CSR(pp) & DCSR_CYC_PEND) { if (timeout == 0) { ecpp_error(pp->dip, "cheerio_reset_dcsr: timeout\n"); break; } else { drv_usecwait(1); timeout--; } } SET_DMAC_CSR(pp, 0); } /* * * Grover Southbridge (M1553) support routines * Southbridge contains an Intel 8237 DMAC onboard which is used * to transport data to/from PCI space to superio parallel port * */ static int m1553_map_regs(struct ecppunit *pp) { if (ddi_regs_map_setup(pp->dip, 1, (caddr_t *)&pp->uh.m1553.isa_space, 0, sizeof (struct isaspace), &acc_attr, &pp->uh.m1553.d_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "m1553_map_regs: failed isa space\n"); goto fail; } if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->i_reg, 0, sizeof (struct info_reg), &acc_attr, &pp->i_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "m1553_map_regs: failed i_reg\n"); goto fail; } if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->f_reg, 0x400, sizeof (struct fifo_reg), &acc_attr, &pp->f_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "m1553_map_regs: failed f_reg\n"); goto fail; } return (SUCCESS); fail: m1553_unmap_regs(pp); return (FAILURE); } static void m1553_unmap_regs(struct ecppunit *pp) { if (pp->uh.m1553.d_handle) { ddi_regs_map_free(&pp->uh.m1553.d_handle); } if (pp->i_handle) { ddi_regs_map_free(&pp->i_handle); } if (pp->f_handle) { ddi_regs_map_free(&pp->f_handle); } } #if defined(__x86) static int x86_map_regs(struct ecppunit *pp) { int nregs = 0; if (ddi_regs_map_setup(pp->dip, 0, (caddr_t *)&pp->i_reg, 0, sizeof (struct info_reg), &acc_attr, &pp->i_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "x86_map_regs: failed i_reg\n"); goto fail; } if (ddi_dev_nregs(pp->dip, &nregs) == DDI_SUCCESS && nregs == 2) { if (ddi_regs_map_setup(pp->dip, 1, (caddr_t *)&pp->f_reg, 0, sizeof (struct fifo_reg), &acc_attr, &pp->f_handle) != DDI_SUCCESS) { ecpp_error(pp->dip, "x86_map_regs: failed f_reg\n"); goto fail; } else pp->noecpregs = FALSE; } else { pp->noecpregs = TRUE; } return (SUCCESS); fail: x86_unmap_regs(pp); return (FAILURE); } static void x86_unmap_regs(struct ecppunit *pp) { if (pp->i_handle) { ddi_regs_map_free(&pp->i_handle); } if (pp->f_handle) { ddi_regs_map_free(&pp->f_handle); } } #endif static uint8_t m1553_read_config_reg(struct ecppunit *pp, uint8_t reg_num) { uint8_t retval; dma8237_write(pp, 0x3F0, reg_num); retval = dma8237_read(pp, 0x3F1); return (retval); } static void m1553_write_config_reg(struct ecppunit *pp, uint8_t reg_num, uint8_t val) { dma8237_write(pp, 0x3F0, reg_num); dma8237_write(pp, 0x3F1, val); } static int m1553_config_chip(struct ecppunit *pp) { uint8_t conreg; /* Unlock configuration regs with "key sequence" */ dma8237_write(pp, 0x3F0, 0x51); dma8237_write(pp, 0x3F0, 0x23); m1553_write_config_reg(pp, PnP_CONFIG_DEV_NO, 0x3); conreg = m1553_read_config_reg(pp, PnP_CONFIG_DEV_NO); ecpp_error(pp->dip, "M1553:conreg7(logical dev)=%x\n", conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_ACTIVATE); ecpp_error(pp->dip, "M1553:conreg30(Active)=%x\n", conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_BASE_ADDR_MSB); ecpp_error(pp->dip, "M1553:conreg60(addrHi)=%x\n", conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_BASE_ADDR_LSB); ecpp_error(pp->dip, "M1553:conreg61(addrLo)=%x\n", conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_INTR_SEL); ecpp_error(pp->dip, "M1553:conreg70(IRQL)=%x\n", conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_DMA0_CHAN); ecpp_error(pp->dip, "M1553:conreg74(DMA0 Chan)=%x\n", conreg); /* set FIFO threshold 1 and ECP mode, preserve bit 7 (IRQ polarity) */ conreg = m1553_read_config_reg(pp, PnP_CONFIG_PP_CONFIG0); conreg = (conreg & ~0x7F) | 0x0A; m1553_write_config_reg(pp, PnP_CONFIG_PP_CONFIG0, conreg); conreg = m1553_read_config_reg(pp, PnP_CONFIG_PP_CONFIG0); ecpp_error(pp->dip, "M1553:conregFO(pport conf)=%x\n", conreg); m1553_write_config_reg(pp, PnP_CONFIG_PP_CONFIG1, 0x04); conreg = m1553_read_config_reg(pp, PnP_CONFIG_PP_CONFIG1); ecpp_error(pp->dip, "M1553:conregF1(outconf)=%x\n", conreg); /* lock configuration regs with key */ dma8237_write(pp, 0x3F0, 0xBB); /* Set ECR, DCR in known state */ ECR_WRITE(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV); DCR_WRITE(pp, ECPP_SLCTIN | ECPP_nINIT); ecpp_error(pp->dip, "m1553_config_chip: ecr=%x, dsr=%x, dcr=%x\n", ECR_READ(pp), DSR_READ(pp), DCR_READ(pp)); return (SUCCESS); } #if defined(__x86) static int x86_config_chip(struct ecppunit *pp) { if (ecr_write(pp, ECR_mode_001 | ECPP_INTR_MASK | ECPP_INTR_SRV) == FAILURE) { ecpp_error(pp->dip, "config chip: failed w/ecr\n"); pp->noecpregs = TRUE; } if (pp->noecpregs) pp->fast_compat = FALSE; DCR_WRITE(pp, ECPP_SLCTIN | ECPP_nINIT); ecpp_error(pp->dip, "x86_config_chip: ecr=%x, dsr=%x, dcr=%x\n", ECR_READ(pp), DSR_READ(pp), DCR_READ(pp)); return (SUCCESS); } #endif /* * dma8237_dma_start() programs the selected 8 bit channel * of DMAC1 with the dma cookie. pp->dma_cookie must * be set before this routine is called. */ static int dma8237_dma_start(struct ecppunit *pp) { uint8_t chn; chn = pp->uh.m1553.chn; ASSERT(chn <= DMAE_CH3 && pp->dma_cookie.dmac_size != 0 && pp->dma_cookie.dmac_address != NULL); /* At this point Southbridge has not yet asserted DREQ */ /* set mode to read-from-memory. */ dma8237_write(pp, DMAC2_MODE, DMAMODE_CASC); if (pp->dma_dir == DDI_DMA_READ) { dma8237_write(pp, DMAC1_MODE, DMAMODE_SINGLE | DMAMODE_READ | chn); } else { dma8237_write(pp, DMAC1_MODE, DMAMODE_SINGLE | DMAMODE_WRITE | chn); } dma8237_write_addr(pp, pp->dma_cookie.dmac_address); dma8237_write_count(pp, pp->dma_cookie.dmac_size - 1); /* * M1553 chip does not permit to access DMA register banks * while DMA is in flight. As a result, ecpp and floppy drivers * can potentially corrupt each other's DMA. The interlocking mechanism * is provided by a parent nexus driver (isadma), which is enabled * indirectly through a DMAC1_ALLMASK register access: * * writing a non-zero value to this register enters a lock, * writing zero releases the lock. * * DMA transfer must only occur after entering a lock. * If the lock is already owned by other driver, we will block. * * The following operation unmasks our channel and masks all others */ dma8237_write(pp, DMAC1_ALLMASK, ~(1 << chn)); pp->uh.m1553.isadma_entered = 1; return (SUCCESS); } static int dma8237_dma_stop(struct ecppunit *pp, size_t *countp) { uint8_t ecr; /* stop DMA */ ecr = (ECR_READ(pp) & 0xe0) | ECPP_INTR_MASK | ECPP_INTR_SRV; (void) ecr_write(pp, ecr); if (pp->uh.m1553.isadma_entered) { /* reset the channel mask so we can issue PIO's to our device */ dma8237_write(pp, DMAC1_ALLMASK, 0); pp->uh.m1553.isadma_entered = 0; } /* read DMA count if requested */ if (countp) { *countp = dma8237_getcnt(pp); if (pp->dma_dir == DDI_DMA_READ && *countp > 0) { (*countp)++; /* need correction for reverse xfers */ } } return (SUCCESS); } #if defined(__x86) static int x86_dma_start(struct ecppunit *pp) { uint8_t chn; struct ddi_dmae_req dmaereq; chn = pp->uh.x86.chn; ASSERT(chn <= DMAE_CH3 && pp->dma_cookie.dmac_size != 0 && pp->dma_cookie.dmac_address != NULL); bzero(&dmaereq, sizeof (struct ddi_dmae_req)); dmaereq.der_command = (pp->dma_dir & DDI_DMA_READ) ? DMAE_CMD_READ : DMAE_CMD_WRITE; if (ddi_dmae_prog(pp->dip, &dmaereq, &pp->dma_cookie, chn) != DDI_SUCCESS) ecpp_error(pp->dip, "prog failed !!!\n"); ecpp_error(pp->dip, "dma_started..\n"); return (SUCCESS); } static int x86_dma_stop(struct ecppunit *pp, size_t *countp) { uint8_t ecr; /* stop DMA */ if (pp->uh.x86.chn == 0xff) return (FAILURE); ecr = (ECR_READ(pp) & 0xe0) | ECPP_INTR_MASK | ECPP_INTR_SRV; (void) ecr_write(pp, ecr); ecpp_error(pp->dip, "dma_stop\n"); /* read DMA count if requested */ if (countp) { *countp = x86_getcnt(pp); } ecpp_error(pp->dip, "dma_stoped..\n"); return (SUCCESS); } #endif /* channel must be masked */ static void dma8237_write_addr(struct ecppunit *pp, uint32_t addr) { uint8_t c_addr, c_lpage; uint16_t c_hpage, *p; switch (pp->uh.m1553.chn) { case DMAE_CH0: c_addr = DMA_0ADR; c_lpage = DMA_0PAGE; c_hpage = DMA_0HPG; break; case DMAE_CH1: c_addr = DMA_1ADR; c_lpage = DMA_1PAGE; c_hpage = DMA_1HPG; break; case DMAE_CH2: c_addr = DMA_2ADR; c_lpage = DMA_2PAGE; c_hpage = DMA_2HPG; break; case DMAE_CH3: c_addr = DMA_3ADR; c_lpage = DMA_3PAGE; c_hpage = DMA_3HPG; break; default: return; } p = (uint16_t *)&pp->uh.m1553.isa_space->isa_reg[c_addr]; ddi_put16(pp->uh.m1553.d_handle, p, addr & 0xFFFF); dma8237_write(pp, c_lpage, (addr & 0xFF0000) >> 16); dma8237_write(pp, c_hpage, (addr & 0xFF000000) >> 24); } /* * This function may be useful during debugging, * so we leave it in, but do not include in the binary */ #ifdef INCLUDE_DMA8237_READ_ADDR static uint32_t dma8237_read_addr(struct ecppunit *pp) { uint8_t rval3, rval4; uint16_t rval16; uint32_t rval; uint8_t c_addr, c_lpage; uint16_t c_hpage, *p; switch (pp->uh.m1553.chn) { case DMAE_CH0: c_addr = DMA_0ADR; c_lpage = DMA_0PAGE; c_hpage = DMA_0HPG; break; case DMAE_CH1: c_addr = DMA_1ADR; c_lpage = DMA_1PAGE; c_hpage = DMA_1HPG; break; case DMAE_CH2: c_addr = DMA_2ADR; c_lpage = DMA_2PAGE; c_hpage = DMA_2HPG; break; case DMAE_CH3: c_addr = DMA_3ADR; c_lpage = DMA_3PAGE; c_hpage = DMA_3HPG; break; default: return (NULL); } p = (uint16_t *)&pp->uh.m1553.isa_space->isa_reg[c_addr]; rval16 = ddi_get16(pp->uh.m1553.d_handle, p); rval3 = dma8237_read(pp, c_lpage); rval4 = dma8237_read(pp, c_hpage); rval = rval16 | (rval3 << 16) | (rval4 <<24); return (rval); } #endif static void dma8237_write_count(struct ecppunit *pp, uint32_t count) { uint8_t c_wcnt; uint16_t *p; switch (pp->uh.m1553.chn) { case DMAE_CH0: c_wcnt = DMA_0WCNT; break; case DMAE_CH1: c_wcnt = DMA_1WCNT; break; case DMAE_CH2: c_wcnt = DMA_2WCNT; break; case DMAE_CH3: c_wcnt = DMA_3WCNT; break; default: return; } p = (uint16_t *)&pp->uh.m1553.isa_space->isa_reg[c_wcnt]; ddi_put16(pp->uh.m1553.d_handle, p, count & 0xFFFF); } static uint32_t dma8237_read_count(struct ecppunit *pp) { uint8_t c_wcnt; uint16_t *p; switch (pp->uh.m1553.chn) { case DMAE_CH0: c_wcnt = DMA_0WCNT; break; case DMAE_CH1: c_wcnt = DMA_1WCNT; break; case DMAE_CH2: c_wcnt = DMA_2WCNT; break; case DMAE_CH3: c_wcnt = DMA_3WCNT; break; default: return (0); } p = (uint16_t *)&pp->uh.m1553.isa_space->isa_reg[c_wcnt]; return (ddi_get16(pp->uh.m1553.d_handle, p)); } static void dma8237_write(struct ecppunit *pp, int reg_num, uint8_t val) { ddi_put8(pp->uh.m1553.d_handle, &pp->uh.m1553.isa_space->isa_reg[reg_num], val); } static uint8_t dma8237_read(struct ecppunit *pp, int reg_num) { return (ddi_get8(pp->uh.m1553.d_handle, &pp->uh.m1553.isa_space->isa_reg[reg_num])); } static size_t dma8237_getcnt(struct ecppunit *pp) { uint32_t cnt; if ((cnt = dma8237_read_count(pp)) == 0xffff) cnt = 0; else cnt++; return (cnt); } /* * * Kstat support routines * */ static void ecpp_kstat_init(struct ecppunit *pp) { struct ecppkstat *ekp; char buf[16]; /* * Allocate, initialize and install interrupt counter kstat */ (void) sprintf(buf, "ecppc%d", pp->instance); pp->intrstats = kstat_create("ecpp", pp->instance, buf, "controller", KSTAT_TYPE_INTR, 1, KSTAT_FLAG_PERSISTENT); if (pp->intrstats == NULL) { ecpp_error(pp->dip, "ecpp_kstat_init:1: kstat_create failed"); } else { pp->intrstats->ks_update = ecpp_kstatintr_update; pp->intrstats->ks_private = (void *) pp; kstat_install(pp->intrstats); } /* * Allocate, initialize and install misc stats kstat */ pp->ksp = kstat_create("ecpp", pp->instance, NULL, "misc", KSTAT_TYPE_NAMED, sizeof (struct ecppkstat) / sizeof (kstat_named_t), KSTAT_FLAG_PERSISTENT); if (pp->ksp == NULL) { ecpp_error(pp->dip, "ecpp_kstat_init:2: kstat_create failed"); return; } ekp = (struct ecppkstat *)pp->ksp->ks_data; #define EK_NAMED_INIT(name) \ kstat_named_init(&ekp->ek_##name, #name, KSTAT_DATA_UINT32) EK_NAMED_INIT(ctx_obytes); EK_NAMED_INIT(ctxpio_obytes); EK_NAMED_INIT(nib_ibytes); EK_NAMED_INIT(ecp_obytes); EK_NAMED_INIT(ecp_ibytes); EK_NAMED_INIT(epp_obytes); EK_NAMED_INIT(epp_ibytes); EK_NAMED_INIT(diag_obytes); EK_NAMED_INIT(to_ctx); EK_NAMED_INIT(to_nib); EK_NAMED_INIT(to_ecp); EK_NAMED_INIT(to_epp); EK_NAMED_INIT(to_diag); EK_NAMED_INIT(xfer_tout); EK_NAMED_INIT(ctx_cf); EK_NAMED_INIT(joblen); EK_NAMED_INIT(isr_reattempt_high); EK_NAMED_INIT(mode); EK_NAMED_INIT(phase); EK_NAMED_INIT(backchan); EK_NAMED_INIT(iomode); EK_NAMED_INIT(state); pp->ksp->ks_update = ecpp_kstat_update; pp->ksp->ks_private = (void *) pp; kstat_install(pp->ksp); } static int ecpp_kstat_update(kstat_t *ksp, int rw) { struct ecppunit *pp; struct ecppkstat *ekp; /* * For the time being there is no point * in supporting writable kstats */ if (rw == KSTAT_WRITE) { return (EACCES); } pp = (struct ecppunit *)ksp->ks_private; ekp = (struct ecppkstat *)ksp->ks_data; mutex_enter(&pp->umutex); ekp->ek_ctx_obytes.value.ui32 = pp->obytes[ECPP_CENTRONICS] + pp->obytes[ECPP_COMPAT_MODE]; ekp->ek_ctxpio_obytes.value.ui32 = pp->ctxpio_obytes; ekp->ek_nib_ibytes.value.ui32 = pp->ibytes[ECPP_NIBBLE_MODE]; ekp->ek_ecp_obytes.value.ui32 = pp->obytes[ECPP_ECP_MODE]; ekp->ek_ecp_ibytes.value.ui32 = pp->ibytes[ECPP_ECP_MODE]; ekp->ek_epp_obytes.value.ui32 = pp->obytes[ECPP_EPP_MODE]; ekp->ek_epp_ibytes.value.ui32 = pp->ibytes[ECPP_EPP_MODE]; ekp->ek_diag_obytes.value.ui32 = pp->obytes[ECPP_DIAG_MODE]; ekp->ek_to_ctx.value.ui32 = pp->to_mode[ECPP_CENTRONICS] + pp->to_mode[ECPP_COMPAT_MODE]; ekp->ek_to_nib.value.ui32 = pp->to_mode[ECPP_NIBBLE_MODE]; ekp->ek_to_ecp.value.ui32 = pp->to_mode[ECPP_ECP_MODE]; ekp->ek_to_epp.value.ui32 = pp->to_mode[ECPP_EPP_MODE]; ekp->ek_to_diag.value.ui32 = pp->to_mode[ECPP_DIAG_MODE]; ekp->ek_xfer_tout.value.ui32 = pp->xfer_tout; ekp->ek_ctx_cf.value.ui32 = pp->ctx_cf; ekp->ek_joblen.value.ui32 = pp->joblen; ekp->ek_isr_reattempt_high.value.ui32 = pp->isr_reattempt_high; ekp->ek_mode.value.ui32 = pp->current_mode; ekp->ek_phase.value.ui32 = pp->current_phase; ekp->ek_backchan.value.ui32 = pp->backchannel; ekp->ek_iomode.value.ui32 = pp->io_mode; ekp->ek_state.value.ui32 = pp->e_busy; mutex_exit(&pp->umutex); return (0); } static int ecpp_kstatintr_update(kstat_t *ksp, int rw) { struct ecppunit *pp; /* * For the time being there is no point * in supporting writable kstats */ if (rw == KSTAT_WRITE) { return (EACCES); } pp = (struct ecppunit *)ksp->ks_private; mutex_enter(&pp->umutex); KSTAT_INTR_PTR(ksp)->intrs[KSTAT_INTR_HARD] = pp->intr_hard; KSTAT_INTR_PTR(ksp)->intrs[KSTAT_INTR_SPURIOUS] = pp->intr_spurious; KSTAT_INTR_PTR(ksp)->intrs[KSTAT_INTR_SOFT] = pp->intr_soft; mutex_exit(&pp->umutex); return (0); }