'\" te
.\"  Copyright (c) 2000, Sun Microsystems, Inc.
.\" , All Rights Reserved
.\" The contents of this file are subject to the terms of the Common Development and Distribution License (the "License").  You may not use this file except in compliance with the License.
.\" You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing.  See the License for the specific language governing permissions and limitations under the License.
.\" When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE.  If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
.TH SCSI_STATUS 9S "Aug 30, 1995"
.SH NAME
scsi_status \- SCSI status structure
.SH SYNOPSIS
.LP
.nf
#include <sys/scsi/scsi.h>
.fi

.SH INTERFACE LEVEL
.sp
.LP
Solaris DDI specific (Solaris DDI)
.SH DESCRIPTION
.sp
.LP
The \fBSCSI-2\fRstandard defines a status byte that is normally sent by the
target to the initiator during the status phase at the completion of each
command.
.SH STRUCTURE MEMBERS
.sp
.in +2
.nf
uchar  sts_scsi2    :1;       /* SCSI-2 modifier bit */
uchar  sts_is       :1;       /* intermediate status sent */
uchar  sts_busy     :1;       /* device busy or reserved */
uchar  sts_cm       :1;       /* condition met */
ucha   sts_chk      :1;       /* check condition */
.fi
.in -2

.sp
.LP
\fBsts_chk\fR indicates that a contingent allegiance condition has occurred.
.sp
.LP
\fBsts_cm\fR is returned whenever the requested operation is satisfied
.sp
.LP
\fBsts_busy\fR indicates that the target is busy. This status is returned
whenever a target is unable to accept a command from an otherwise acceptable
initiator (that is, no reservation conflicts). The recommended initiator
recovery action is to issue the command again later.
.sp
.LP
\fBsts_is\fR is returned for every successfully completed command in a series
of linked commands (except the last command), unless the command is terminated
with a check condition status, reservation conflict, or command terminated
status. Note that host bus adapter drivers may not support linked commands (see
\fBscsi_ifsetcap\fR(9F)). If \fBsts_is\fR and \fBsts_busy\fR are both set, then
a reservation conflict has occurred.
.sp
.LP
\fBsts_scsi2\fR is the \fBSCSI-2 \fRmodifier bit. If \fBsts_scsi2\fR and
\fBsts_chk\fR are both set, this indicates a command terminated status. If
\fBsts_scsi2\fR and \fBsts_busy\fR are both set, this indicates that the
command queue in the target is full.
.sp
.LP
For accessing the status as a byte, the following values are appropriate:
.sp
.ne 2
.na
\fB\fBSTATUS_GOOD\fR \fR
.ad
.sp .6
.RS 4n
This status indicates that the target has successfully completed the command.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_CHECK\fR \fR
.ad
.sp .6
.RS 4n
This status indicates that a contingent allegiance condition has occurred.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_MET\fR \fR
.ad
.sp .6
.RS 4n
This status is returned when the requested operations are satisfied.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_BUSY\fR \fR
.ad
.sp .6
.RS 4n
This status indicates that the target is busy.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_INTERMEDIATE\fR \fR
.ad
.sp .6
.RS 4n
This status is returned for every successfully completed command in a series of
linked commands.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_SCSI2\fR \fR
.ad
.sp .6
.RS 4n
This is the \fBSCSI-2 \fRmodifier bit.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_INTERMEDIATE_MET\fR \fR
.ad
.sp .6
.RS 4n
This status is a combination of \fBSTATUS_MET\fR and \fBSTATUS_INTERMEDIATE\fR.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_RESERVATION_CONFLICT\fR \fR
.ad
.sp .6
.RS 4n
This status is a combination of \fBSTATUS_INTERMEDIATE\fR and
\fBSTATUS_BUSY\fR, and it is returned whenever an initiator attempts to access
a logical unit or an extent within a logical unit is reserved.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_TERMINATED\fR \fR
.ad
.sp .6
.RS 4n
This status is a combination of \fBSTATUS_SCSI2\fR and \fBSTATUS_CHECK,\fR and
it is returned whenever the target terminates the current \fBI/O\fR process
after receiving a terminate \fBI/O\fR process message.
.RE

.sp
.ne 2
.na
\fB\fBSTATUS_QFULL\fR \fR
.ad
.sp .6
.RS 4n
This status is a combination of \fBSTATUS_SCSI2\fR and \fBSTATUS_BUSY\fR, and
it is returned when the command queue in the target is full.
.RE

.SH SEE ALSO
.sp
.LP
\fBscsi_ifgetcap\fR(9F), \fBscsi_init_pkt\fR(9F),
\fBscsi_extended_sense\fR(9S), \fBscsi_pkt\fR(9S)
.sp
.LP
\fIWriting Device Drivers\fR