/* * CDDL HEADER START * * The contents of this file are subject to the terms of the * Common Development and Distribution License (the "License"). * You may not use this file except in compliance with the License. * * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE * or http://www.opensolaris.org/os/licensing. * See the License for the specific language governing permissions * and limitations under the License. * * When distributing Covered Code, include this CDDL HEADER in each * file and include the License file at usr/src/OPENSOLARIS.LICENSE. * If applicable, add the following below this CDDL HEADER, with the * fields enclosed by brackets "[]" replaced with your own identifying * information: Portions Copyright [yyyy] [name of copyright owner] * * CDDL HEADER END */ /* * Copyright (c) 2008, 2010, Oracle and/or its affiliates. All rights reserved. */ #ifndef _FRAMEWORK_SES2_H #define _FRAMEWORK_SES2_H #ifdef __cplusplus extern "C" { #endif /* * Node properties */ typedef enum ses2_element_type { SES_ET_UNSPECIFIED = 0, SES_ET_DEVICE = 0x1, SES_ET_POWER_SUPPLY = 0x2, SES_ET_COOLING = 0x3, SES_ET_TEMPERATURE_SENSOR = 0x4, SES_ET_DOOR_LOCK = 0x5, SES_ET_AUDIBLE_ALARM = 0x6, SES_ET_ESC_ELECTRONICS = 0x7, SES_ET_SCC_ELECTRONICS = 0x8, SES_ET_NONVOLATILE_CACHE = 0x9, SES_ET_INVALID_OPERATION_REASON = 0xa, SES_ET_UPS = 0xb, SES_ET_DISPLAY = 0xc, SES_ET_KEY_PAD_ENTRY = 0xd, SES_ET_ENCLOSURE = 0xe, SES_ET_SCSI_PORT_XCVR = 0xf, SES_ET_LANGUAGE = 0x10, SES_ET_COMMUNICATION_PORT = 0x11, SES_ET_VOLTAGE_SENSOR = 0x12, SES_ET_CURRENT_SENSOR = 0x13, SES_ET_SCSI_TARGET_PORT = 0x14, SES_ET_SCSI_INITIATOR_PORT = 0x15, SES_ET_SIMPLE_SUBENCLOSURE = 0x16, SES_ET_ARRAY_DEVICE = 0x17, SES_ET_SAS_EXPANDER = 0x18, SES_ET_SAS_CONNECTOR = 0x19 } ses2_element_type_t; #define SES_PROP_STATUS_CODE "ses-status-code" typedef enum ses_element_status_code { SES_ESC_UNSUPPORTED = 0, SES_ESC_OK = 1, SES_ESC_CRITICAL = 2, SES_ESC_NONCRITICAL = 3, SES_ESC_UNRECOVERABLE = 4, SES_ESC_NOT_INSTALLED = 5, SES_ESC_UNKNOWN = 6, SES_ESC_UNAVAIL = 7, SES_ESC_NO_ACCESS = 8 } ses_element_status_code_t; #define SES_PROP_ELEMENT_CLASS_INDEX "ses-element-class-index" /* U64 */ #define SES_PROP_ELEMENT_INDEX "ses-element-index" /* U64 */ #define SES_PROP_ELEMENT_ONLY_INDEX "ses-element-only-index" /* U64 */ #define SES_PROP_BAY_NUMBER "ses-bay-number" /* U64 */ #define SES_PROP_PRDFAIL "ses-failure-predicted" #define SES_PROP_SWAP "ses-swapped" #define SES_PROP_DISABLED "ses-disabled" #define SES_PROP_IDENT "ses-identify" #define SES_PROP_WARN "ses-warning" #define SES_PROP_FAIL "ses-failed" #define SES_PROP_WARN_REQ "ses-warning-indicator-requested" #define SES_PROP_FAIL_REQ "ses-failure-indicator-requested" #define SES_PROP_REPORT "ses-reported-via" #define SES_PROP_RMV "ses-ready-to-remove" #define SES_PROP_OFF "ses-off" #define SES_PROP_REQUESTED_ON "ses-requested-on" #define SES_PROP_CLASS_DESCRIPTION "ses-class-description" /* S */ #define SES_PROP_DESCRIPTION "ses-description" /* S */ #define SES_PROP_HOT_SWAP "ses-hot-swappable" #define SES_PROP_CRIT_OVER "ses-critical-over" #define SES_PROP_CRIT_UNDER "ses-critical-under" #define SES_PROP_WARN_OVER "ses-warning-over" #define SES_PROP_WARN_UNDER "ses-warning-under" #define SES_FC_PROP_NODE_NAME "ses-fc-node-name" /* U64 */ #define SES_FC_PROP_LOOP_POS "ses-fc-loop-position" /* U64 */ #define SES_FC_PROP_REQ_HARDADDR "ses-fc-requested-hard-address" #define SES_FC_PROP_N_PORT_ID "ses-fc-n_port-identifier" /* U64 */ #define SES_FC_PROP_N_PORT_NAME "ses-fc-n_port-name" /* U64 */ #define SES_FC_PROP_PORTS "ses-fc-ports" /* NVA */ #define SES_SAS_PROP_DEVICE_TYPE "ses-sas-device-type" /* U64 */ /* * SAS2r11 7.8.2 Table 123 */ typedef enum sas_device_type { SAS_DT_END_DEVICE = 0x01, SAS_DT_EXPANDER = 0x02, SAS_DT_LEGACY_EXPANDER = 0x3 } sas_device_type_t; #define SES_SAS_PROP_SMPI_PORT "ses-sas-smp-initiator-port" #define SES_SAS_PROP_STPI_PORT "ses-sas-stp-initiator-port" #define SES_SAS_PROP_SSPI_PORT "ses-sas-ssp-initiator-port" #define SES_SAS_PROP_SATA_DEVICE "ses-sas-sata-device" #define SES_SAS_PROP_SMPT_PORT "ses-sas-smp-target-port" #define SES_SAS_PROP_STPT_PORT "ses-sas-stp-target-port" #define SES_SAS_PROP_SSPT_PORT "ses-sas-ssp-target-port" #define SES_SAS_PROP_ATT_ADDR "ses-sas-attached-address" /* U64 */ #define SES_SAS_PROP_ADDR "ses-sas-address" /* U64 */ #define SES_SAS_PROP_PHY_ID "ses-sas-phy-identifier" /* U64 */ #define SES_SAS_PROP_PHYS "ses-sas-phys" /* NVA */ #define SES_PROP_CE_IDX "ses-connector-element-index" /* U64 */ #define SES_PROP_OE_IDX "ses-other-element-index" /* U64 */ #define SES_PROP_THRESH_CRIT_HI "ses-high-critical-threshold" /* U64 */ #define SES_PROP_THRESH_WARN_HI "ses-high-warning-threshold" /* U64 */ #define SES_PROP_THRESH_CRIT_LO "ses-low-critical-threshold" /* U64 */ #define SES_PROP_THRESH_WARN_LO "ses-low-warning-threshold" /* U64 */ /* * Audible Alarm properties */ #define SES_ALARM_PROP_UNRECOV "ses-indicating-unrecoverable" #define SES_ALARM_PROP_CRIT "ses-indicating-critical" #define SES_ALARM_PROP_NONCRIT "ses-indicating-noncritical" #define SES_ALARM_PROP_INFO "ses-indicating-informational" #define SES_ALARM_PROP_REMIND "ses-reminder-mode" #define SES_ALARM_PROP_MUTED "ses-muted" #define SES_ALARM_PROP_RQST_MUTE "ses-mute-requested" /* * Nonvolatile Cache properties */ #define SES_CACHE_PROP_SIZE "ses-cache-size" /* U64 */ /* * Cooling Element properties */ #define SES_COOLING_PROP_FAN_SPEED "ses-fan-speed" /* U64 */ #define SES_COOLING_PROP_SPEED_CODE "ses-fan-speed-code" /* U64 */ typedef enum ses_cooling_fan_speed { SES_COOLING_FAN_SPEED_STOPPED = 0, SES_COOLING_FAN_SPEED_LOWEST = 1, SES_COOLING_FAN_SPEED_LOWER = 2, SES_COOLING_FAN_SPEED_LOW = 3, SES_COOLING_FAN_SPEED_INTERMEDIATE = 4, SES_COOLING_FAN_SPEED_HIGH = 5, SES_COOLING_FAN_SPEED_HIGHER = 6, SES_COOLING_FAN_SPEED_HIGHEST = 7 } ses_cooling_fan_speed_t; /* * Device/Array Device properties */ #define SES_DEV_PROP_SLOT_ADDR "ses-slot-address" /* U64 */ #define SES_DEV_PROP_PRDFAIL "ses-failure-predicted" #define SES_DEV_PROP_READY_TO_INSERT "ses-ready-to-insert" #define SES_DEV_PROP_ENC_BYP_A "ses-enclosure-bypassed-a" #define SES_DEV_PROP_ENC_BYP_B "ses-enclosure-bypassed-b" #define SES_DEV_PROP_DO_NOT_REMOVE "ses-do-not-remove" #define SES_DEV_PROP_APP_BYP_A "ses-app-client-bypassed-a" #define SES_DEV_PROP_APP_BYP_B "ses-app-client-bypassed-b" #define SES_DEV_PROP_DEV_BYP_A "ses-device-bypassed-a" #define SES_DEV_PROP_DEV_BYP_B "ses-device-bypassed-b" #define SES_DEV_PROP_BYP_A "ses-bypassed-a" #define SES_DEV_PROP_BYP_B "ses-bypassed-b" #define SES_DEV_PROP_FAULT_RQSTD "ses-fault-requested" #define SES_DEV_PROP_FAULT_SENSED "ses-fault-sensed" #define SES_DEV_PROP_SAS_NOT_ALL_PHYS "ses-sas-not-all-phys" /* Control only */ #define SES_DEV_PROP_REQ_MISSING "ses-request-missing" #define SES_DEV_PROP_REQ_ACTIVE "ses-request-activity" #define SES_AD_PROP_RR_ABORT "ses-remap-rebuild-abort" #define SES_AD_PROP_REBUILD "ses-remap-rebuild" #define SES_AD_PROP_IN_FAILED_ARRAY "ses-in-failed-array" #define SES_AD_PROP_IN_CRIT_ARRAY "ses-in-critical-array" #define SES_AD_PROP_CONS_CHK "ses-consistency-check" #define SES_AD_PROP_HOT_SPARE "ses-hot-spare" #define SES_AD_PROP_RSVD_DEVICE "ses-reserved-device" #define SES_AD_PROP_OK "ses-ok" /* * Display Element properties */ #define SES_DPY_PROP_CHAR "ses-displayed-character" /* U16 */ #define SES_DPY_PROP_MODE "ses-display-mode" /* U64 */ /* * SES-2r17 Table 96, 7.3.14 */ typedef enum ses_display_mode_ctl { SES_DISPLAY_MC_NOCHG = 0, SES_DISPLAY_MC_ESP = 1, SES_DISPLAY_MC_SET = 2 } ses_display_mode_ctl_t; typedef enum ses2_display_mode_status { SES_DISPLAY_MS_NOTSUP = 0, SES_DISPLAY_MS_ESP = 1, SES_DISPLAY_MS_SET = 2 } ses_display_mode_status_t; /* * Current Sensor properties */ #define SES_CS_PROP_CURRENT_MA "ses-current" /* I64 */ /* * Door Lock properties */ #define SES_LOCK_PROP_UNLOCKED "ses-unlocked" /* * SCSI Initiator or Target Port properties */ #define SES_ITP_PROP_ENABLED "ses-enabled" /* * Language Module properties */ #define SES_LANG_PROP_LANGCODE "ses-language-code" /* U64 */ /* * SCSI Port/Transceiver properties */ #define SES_PX_PROP_XMIT_FAIL "ses-transmitter-failure" #define SES_PX_PROP_LOL "ses-loss-of-link" /* * Power Supply properties */ #define SES_PSU_PROP_DC_OVER_CURRENT "ses-dc-over-current" #define SES_PSU_PROP_DC_UNDER_VOLTAGE "ses-dc-under-voltage" #define SES_PSU_PROP_DC_OVER_VOLTAGE "ses-dc-over-voltage" #define SES_PSU_PROP_DC_FAIL "ses-dc-fail" #define SES_PSU_PROP_AC_FAIL "ses-ac-fail" #define SES_PSU_PROP_TEMP_WARN "ses-temperature-warning" /* I64 */ #define SES_PSU_PROP_OVERTEMP_FAIL "ses-overtemperature-failure" /* * SAS Expander properties */ #define SES_EXP_PROP_SAS_ADDR "ses-expander-sas-address" /* U64 */ /* * SAS Connector properties */ #define SES_SC_PROP_PHYSICAL_LINK "ses-sas-physical-link" /* U64 */ #define SES_SC_PROP_CONNECTOR_TYPE "ses-sas-connector-type" /* U64 */ /* * SES2r17 Table 122, 7.3.26 */ typedef enum ses_sasconn_type { SES_SASCONN_T_UNKNOWN = 0, SES_SASCONN_T_SFF_8470 = 0x1, SES_SASCONN_T_SFF_8088 = 0x2, SES_SASCONN_T_VENDOR_EXT = 0xf, SES_SASCONN_T_SFF_8484 = 0x10, SES_SASCONN_T_SFF_8087 = 0x11, SES_SASCONN_T_SFF_8482_R = 0x20, SES_SASCONN_T_SATA_HOST = 0x21, SES_SASCONN_T_SFF_8482_P = 0x22, SES_SASCONN_T_SATA_DEV = 0x23, SES_SASCONN_T_VIRTUAL = 0x2f, SES_SASCONN_T_VENDOR_INT = 0x3f, SES_SASCONN_T_VENDOR_70 = 0x70, SES_SASCONN_T_VENDOR_71 = 0x71, SES_SASCONN_T_VENDOR_72 = 0x72, SES_SASCONN_T_VENDOR_73 = 0x73, SES_SASCONN_T_VENDOR_74 = 0x74, SES_SASCONN_T_VENDOR_75 = 0x75, SES_SASCONN_T_VENDOR_76 = 0x76, SES_SASCONN_T_VENDOR_77 = 0x77, SES_SASCONN_T_VENDOR_78 = 0x78, SES_SASCONN_T_VENDOR_79 = 0x79, SES_SASCONN_T_VENDOR_7A = 0x7a, SES_SASCONN_T_VENDOR_7B = 0x7b, SES_SASCONN_T_VENDOR_7C = 0x7c, SES_SASCONN_T_VENDOR_7D = 0x7d, SES_SASCONN_T_VENDOR_7E = 0x7e, SES_SASCONN_T_VENDOR_7F = 0x7f } ses_sasconn_type_t; /* * Simple Subenclosure properties */ #define SES_SS_PROP_SHORT_STATUS "ses-short-status" /* U64 */ /* * Temperature Sensor properties */ #define SES_TEMP_PROP_TEMP "ses-temperature" /* I64 */ /* * Uninterruptible Power Supply properties */ #define SES_UPS_PROP_TIMELEFT "ses-battery-time-remaining" /* U64 */ #define SES_UPS_PROP_INTF_FAIL "ses-interface-failure" #define SES_UPS_PROP_WARN "ses-low-battery-warning" #define SES_UPS_PROP_UPS_FAIL "ses-ups-failure" #define SES_UPS_PROP_DC_FAIL "ses-dc-failure" #define SES_UPS_PROP_AC_FAIL "ses-ac-failure" #define SES_UPS_PROP_AC_QUAL "ses-ac-quality-exception" #define SES_UPS_PROP_AC_HI "ses-ac-overvoltage-exception" #define SES_UPS_PROP_AC_LO "ses-ac-undervoltage-exception" #define SES_UPS_PROP_BPF "ses-battery-failure-predicted" #define SES_UPS_PROP_BATT_FAIL "ses-battery-failure" /* * Voltage Sensor properties */ #define SES_VS_PROP_VOLTAGE_MV "ses-voltage" /* I64 */ /* * Enclosure Services Controller properties (Control only) */ #define SES_ESC_PROP_SELECT "ses-select-element" /* * Primary/Subenclosure properties */ #define SES_EN_PROP_EID "ses-enclosure-id" /* U64 */ #define SES_EN_PROP_ESPID "ses-enclosure-service-proc-id" #define SES_EN_PROP_NESP "ses-enclosure-service-proc-count" #define SES_EN_PROP_LID "ses-logical-id" /* NV */ #define SES_EN_PROP_VID "ses-vendor-id" /* S */ #define SES_EN_PROP_PID "ses-product-id" /* S */ #define SES_EN_PROP_REV "ses-product-revision" /* S */ #define SES_EN_PROP_VS "ses-product-vendor-specific" /* BA */ #define SES_EN_PROP_UNRECOV "ses-status-unrecoverable" #define SES_EN_PROP_CRIT "ses-status-critical" #define SES_EN_PROP_NONCRIT "ses-status-noncritical" #define SES_EN_PROP_INFO "ses-status-informational" #define SES_EN_PROP_INVOP "ses-status-invalid-operation" #define SES_EN_PROP_HELP "ses-help-text" /* S */ #define SES_EN_PROP_STRING "ses-string-in-data" /* BA */ #define SES_EN_PROP_SHORT "ses-short-status" /* U64 */ #define SES_EN_PROP_UCODE "ses-microcode-dl-status" /* U64 */ typedef enum ses2_dl_ucode_status { SES2_DLUCODE_S_NOP = 0, SES2_DLUCODE_S_INPROGRESS = 0x1, SES2_DLUCODE_S_SAVING = 0x2, SES2_DLUCODE_S_INTERIM_3 = 0x3, SES2_DLUCODE_S_INTERIM_4 = 0x4, SES2_DLUCODE_S_INTERIM_5 = 0x5, SES2_DLUCODE_S_INTERIM_6 = 0x6, SES2_DLUCODE_S_INTERIM_7 = 0x7, SES2_DLUCODE_S_INTERIM_8 = 0x8, SES2_DLUCODE_S_INTERIM_9 = 0x9, SES2_DLUCODE_S_INTERIM_A = 0xa, SES2_DLUCODE_S_INTERIM_B = 0xb, SES2_DLUCODE_S_INTERIM_C = 0xc, SES2_DLUCODE_S_INTERIM_D = 0xd, SES2_DLUCODE_S_INTERIM_E = 0xe, SES2_DLUCODE_S_INTERIM_F = 0xf, SES2_DLUCODE_S_COMPLETE_NOW = 0x10, SES2_DLUCODE_S_COMPLETE_AT_RESET = 0x11, SES2_DLUCODE_S_COMPLETE_AT_POWERON = 0x12, SES2_DLUCODE_S_VENDOR_70 = 0x70, SES2_DLUCODE_S_VENDOR_71 = 0x71, SES2_DLUCODE_S_VENDOR_72 = 0x72, SES2_DLUCODE_S_VENDOR_73 = 0x73, SES2_DLUCODE_S_VENDOR_74 = 0x74, SES2_DLUCODE_S_VENDOR_75 = 0x75, SES2_DLUCODE_S_VENDOR_76 = 0x76, SES2_DLUCODE_S_VENDOR_77 = 0x77, SES2_DLUCODE_S_VENDOR_78 = 0x78, SES2_DLUCODE_S_VENDOR_79 = 0x79, SES2_DLUCODE_S_VENDOR_7A = 0x7a, SES2_DLUCODE_S_VENDOR_7B = 0x7b, SES2_DLUCODE_S_VENDOR_7C = 0x7c, SES2_DLUCODE_S_VENDOR_7D = 0x7d, SES2_DLUCODE_S_VENDOR_7E = 0x7e, SES2_DLUCODE_S_VENDOR_7F = 0x7f, SES2_DLUCODE_S_PAGE_ERR = 0x80, SES2_DLUCODE_S_IMAGE_ERR = 0x81, SES2_DLUCODE_S_TIMEOUT = 0x82, SES2_DLUCODE_S_INTERNAL_NEEDIMAGE = 0x83, SES2_DLUCODE_S_INTERNAL_SAFE = 0x84, SES2_DLUCODE_S_VENDOR_ERR_F0 = 0xf0, SES2_DLUCODE_S_VENDOR_ERR_F1 = 0xf1, SES2_DLUCODE_S_VENDOR_ERR_F2 = 0xf2, SES2_DLUCODE_S_VENDOR_ERR_F3 = 0xf3, SES2_DLUCODE_S_VENDOR_ERR_F4 = 0xf4, SES2_DLUCODE_S_VENDOR_ERR_F5 = 0xf5, SES2_DLUCODE_S_VENDOR_ERR_F6 = 0xf6, SES2_DLUCODE_S_VENDOR_ERR_F7 = 0xf7, SES2_DLUCODE_S_VENDOR_ERR_F8 = 0xf8, SES2_DLUCODE_S_VENDOR_ERR_F9 = 0xf9, SES2_DLUCODE_S_VENDOR_ERR_FA = 0xfa, SES2_DLUCODE_S_VENDOR_ERR_FB = 0xfb, SES2_DLUCODE_S_VENDOR_ERR_FC = 0xfc, SES2_DLUCODE_S_VENDOR_ERR_FD = 0xfd, SES2_DLUCODE_S_VENDOR_ERR_FE = 0xfe, SES2_DLUCODE_S_VENDOR_ERR_FF = 0xff } ses2_dl_ucode_status_t; typedef enum ses_dl_ucode_mode { SES_DLUCODE_M_WITH_OFFS = 6, SES_DLUCODE_M_WITH_OFFS_SAVE = 7 } ses_dl_ucode_mode_t; #define SES_EN_PROP_UCODE_A "ses-microcode-dl-addl-status" /* U64 */ #define SES_EN_PROP_UCODE_SZ "ses-microcode-maximum-size" /* U64 */ #define SES_EN_PROP_UCODE_BUF "ses-microcode-buffer-id" /* U64 */ #define SES_EN_PROP_UCODE_OFF "ses-microcode-buffer-offset" /* U64 */ #define SES_EN_PROP_NICK "ses-nickname" /* S */ #define SES_EN_PROP_NICK_STATUS "ses-nickname-status" /* U64 */ typedef enum ses_subnick_status { SES_SNS_NO_ERROR = 0x0, SES_SNS_ERR_PAGE = 0x80, SES_SNS_ERR_INT_NICKLOST = 0x81, SES_SNS_ERR_INT_PRESERVED = 0x82 } ses_subnick_status_t; #define SES_EN_PROP_NICK_ADDL_STATUS "ses-nickname-additional-status" #define SES_EN_PROP_NICK_LANG "ses-nickname-language" /* U64 */ #define SES_EN_PROP_POWER_DELAY "ses-power-cycle-delay" /* U64 */ #define SES_EN_PROP_POWER_DURATION "ses-power-cycle-duration" /* U64 */ #define SES_EN_PROP_POWER_REQUEST "ses-power-cycle-request" /* U64 */ typedef enum ses_power_delay { SES_PDL_NONE = 0x0, SES_PDL_IMMEDIATE = 0x3f } ses_power_delay_t; typedef enum ses_power_duration { SES_PDR_NONE = 0x0, SES_PDR_MANUAL = 0x3f } ses_power_duration_t; typedef enum ses_power_request { SES_PRQ_NONE = 0x0, SES_PRQ_SET = 0x1, SES_PRQ_CANCEL = 0x2 } ses_power_request_t; /* * IEEE logical IDs (for SES_EN_PROP_LID) */ #define SPC3_NAA_INT "naa-id-integer" /* U64 */ #define SPC3_NAA_ID_TYPE "naa-id-type" /* U64 */ #define SPC3_NAA_COMPANY_ID "naa-company-id" /* U64 */ #define SPC3_NAA_VS_A "naa-vendor-specific-a" /* U64 */ #define SPC3_NAA_VS_B "naa-vendor-specific-b" /* U64 */ /* * SES-2 Diagnostic page codes (Table 5, 6.1.1). The set of exported pages * constitutes an inter-plugin interface and is therefore part of the public * header file. */ typedef enum ses2_diag_page { SES2_DIAGPAGE_SUPPORTED_PAGES = 0x00, SES2_DIAGPAGE_CONFIG = 0x01, SES2_DIAGPAGE_ENCLOSURE_CTL_STATUS = 0x02, SES2_DIAGPAGE_HELP_TEXT = 0x03, SES2_DIAGPAGE_STRING_IO = 0x04, SES2_DIAGPAGE_THRESHOLD_IO = 0x05, SES2_DIAGPAGE_ELEMENT_DESC = 0x07, SES2_DIAGPAGE_SHORT_STATUS = 0x08, SES2_DIAGPAGE_ENCLOSURE_BUSY = 0x09, SES2_DIAGPAGE_ADDL_ELEM_STATUS = 0x0a, SES2_DIAGPAGE_SUBENCLOSURE_HELP_TEXT = 0x0b, SES2_DIAGPAGE_SUBENCLOSURE_STRING_IO = 0x0c, SES2_DIAGPAGE_SUPPORTED_SES_PAGES = 0x0d, SES2_DIAGPAGE_DL_MICROCODE_CTL_STATUS = 0x0e, SES2_DIAGPAGE_SUBENCLOSURE_NICKNAME_CTL_STATUS = 0x0f, SES2_DIAGPAGE_VENDOR_0 = 0x10, SES2_DIAGPAGE_VENDOR_1 = 0x11, SES2_DIAGPAGE_VENDOR_2 = 0x12, SES2_DIAGPAGE_VENDOR_3 = 0x13, SES2_DIAGPAGE_VENDOR_4 = 0x14, SES2_DIAGPAGE_VENDOR_5 = 0x15, SES2_DIAGPAGE_VENDOR_6 = 0x16, SES2_DIAGPAGE_VENDOR_7 = 0x17, SES2_DIAGPAGE_VENDOR_8 = 0x18, SES2_DIAGPAGE_VENDOR_9 = 0x19, SES2_DIAGPAGE_VENDOR_A = 0x1a, SES2_DIAGPAGE_VENDOR_B = 0x1b, SES2_DIAGPAGE_VENDOR_C = 0x1c, SES2_DIAGPAGE_VENDOR_D = 0x1d, SES2_DIAGPAGE_VENDOR_E = 0x1e, SES2_DIAGPAGE_VENDOR_F = 0x1f } ses2_diag_page_t; #define SES_CTL_OP_SETPROP "ses-ctl-setprop" #define SES_CTL_OP_DL_UCODE "ses-ctl-dl-ucode" #define SES_CTL_PROP_UCODE_DATA "ses-ctl-ucode-data" #define SES_CTL_PROP_UCODE_BUFID "ses-ctl-ucode-bufid" #define SES_CTL_PROP_UCODE_MODE "ses-ctl-ucode-mode" #define SES_CTL_PROP_UCODE_DATA_LEN "ses-ctl-ucode-data-length" /* U64 */ #ifdef __cplusplus } #endif #endif /* _FRAMEWORK_SES2_H */