/*- * Copyright (c) 2012 * Ben Gray . * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); /* * SMSC LAN9xxx devices (http://www.smsc.com/) * * The LAN9500 & LAN9500A devices are stand-alone USB to Ethernet chips that * support USB 2.0 and 10/100 Mbps Ethernet. * * The LAN951x devices are an integrated USB hub and USB to Ethernet adapter. * The driver only covers the Ethernet part, the standard USB hub driver * supports the hub part. * * This driver is closely modelled on the Linux driver written and copyrighted * by SMSC. * * * * * H/W TCP & UDP Checksum Offloading * --------------------------------- * The chip supports both tx and rx offloading of UDP & TCP checksums, this * feature can be dynamically enabled/disabled. * * RX checksuming is performed across bytes after the IPv4 header to the end of * the Ethernet frame, this means if the frame is padded with non-zero values * the H/W checksum will be incorrect, however the rx code compensates for this. * * TX checksuming is more complicated, the device requires a special header to * be prefixed onto the start of the frame which indicates the start and end * positions of the UDP or TCP frame. This requires the driver to manually * go through the packet data and decode the headers prior to sending. * On Linux they generally provide cues to the location of the csum and the * area to calculate it over, on FreeBSD we seem to have to do it all ourselves, * hence this is not as optimal and therefore h/w tX checksum is currently not * implemented. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "opt_platform.h" #ifdef FDT #include #include #include #endif #include #include #include #include "usbdevs.h" #define USB_DEBUG_VAR smsc_debug #include #include #include #include #include "if_smscreg.h" #ifdef USB_DEBUG static int smsc_debug = 0; SYSCTL_NODE(_hw_usb, OID_AUTO, smsc, CTLFLAG_RW, 0, "USB smsc"); SYSCTL_INT(_hw_usb_smsc, OID_AUTO, debug, CTLFLAG_RW, &smsc_debug, 0, "Debug level"); #endif /* * Various supported device vendors/products. */ static const struct usb_device_id smsc_devs[] = { #define SMSC_DEV(p,i) { USB_VPI(USB_VENDOR_SMC2, USB_PRODUCT_SMC2_##p, i) } SMSC_DEV(LAN9514_ETH, 0), #undef SMSC_DEV }; #ifdef USB_DEBUG #define smsc_dbg_printf(sc, fmt, args...) \ do { \ if (smsc_debug > 0) \ device_printf((sc)->sc_ue.ue_dev, "debug: " fmt, ##args); \ } while(0) #else #define smsc_dbg_printf(sc, fmt, args...) #endif #define smsc_warn_printf(sc, fmt, args...) \ device_printf((sc)->sc_ue.ue_dev, "warning: " fmt, ##args) #define smsc_err_printf(sc, fmt, args...) \ device_printf((sc)->sc_ue.ue_dev, "error: " fmt, ##args) #define ETHER_IS_ZERO(addr) \ (!(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5])) #define ETHER_IS_VALID(addr) \ (!ETHER_IS_MULTICAST(addr) && !ETHER_IS_ZERO(addr)) static device_probe_t smsc_probe; static device_attach_t smsc_attach; static device_detach_t smsc_detach; static usb_callback_t smsc_bulk_read_callback; static usb_callback_t smsc_bulk_write_callback; static miibus_readreg_t smsc_miibus_readreg; static miibus_writereg_t smsc_miibus_writereg; static miibus_statchg_t smsc_miibus_statchg; #if __FreeBSD_version > 1000000 static int smsc_attach_post_sub(struct usb_ether *ue); #endif static uether_fn_t smsc_attach_post; static uether_fn_t smsc_init; static uether_fn_t smsc_stop; static uether_fn_t smsc_start; static uether_fn_t smsc_tick; static uether_fn_t smsc_setmulti; static uether_fn_t smsc_setpromisc; static int smsc_ifmedia_upd(struct ifnet *); static void smsc_ifmedia_sts(struct ifnet *, struct ifmediareq *); static int smsc_chip_init(struct smsc_softc *sc); static int smsc_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data); static const struct usb_config smsc_config[SMSC_N_TRANSFER] = { [SMSC_BULK_DT_WR] = { .type = UE_BULK, .endpoint = UE_ADDR_ANY, .direction = UE_DIR_OUT, .frames = 16, .bufsize = 16 * (MCLBYTES + 16), .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, .callback = smsc_bulk_write_callback, .timeout = 10000, /* 10 seconds */ }, [SMSC_BULK_DT_RD] = { .type = UE_BULK, .endpoint = UE_ADDR_ANY, .direction = UE_DIR_IN, .bufsize = 20480, /* bytes */ .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, .callback = smsc_bulk_read_callback, .timeout = 0, /* no timeout */ }, /* The SMSC chip supports an interrupt endpoints, however they aren't * needed as we poll on the MII status. */ }; static const struct usb_ether_methods smsc_ue_methods = { .ue_attach_post = smsc_attach_post, #if __FreeBSD_version > 1000000 .ue_attach_post_sub = smsc_attach_post_sub, #endif .ue_start = smsc_start, .ue_ioctl = smsc_ioctl, .ue_init = smsc_init, .ue_stop = smsc_stop, .ue_tick = smsc_tick, .ue_setmulti = smsc_setmulti, .ue_setpromisc = smsc_setpromisc, .ue_mii_upd = smsc_ifmedia_upd, .ue_mii_sts = smsc_ifmedia_sts, }; /** * smsc_read_reg - Reads a 32-bit register on the device * @sc: driver soft context * @off: offset of the register * @data: pointer a value that will be populated with the register value * * LOCKING: * The device lock must be held before calling this function. * * RETURNS: * 0 on success, a USB_ERR_?? error code on failure. */ static int smsc_read_reg(struct smsc_softc *sc, uint32_t off, uint32_t *data) { struct usb_device_request req; uint32_t buf; usb_error_t err; SMSC_LOCK_ASSERT(sc, MA_OWNED); req.bmRequestType = UT_READ_VENDOR_DEVICE; req.bRequest = SMSC_UR_READ_REG; USETW(req.wValue, 0); USETW(req.wIndex, off); USETW(req.wLength, 4); err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); if (err != 0) smsc_warn_printf(sc, "Failed to read register 0x%0x\n", off); *data = le32toh(buf); return (err); } /** * smsc_write_reg - Writes a 32-bit register on the device * @sc: driver soft context * @off: offset of the register * @data: the 32-bit value to write into the register * * LOCKING: * The device lock must be held before calling this function. * * RETURNS: * 0 on success, a USB_ERR_?? error code on failure. */ static int smsc_write_reg(struct smsc_softc *sc, uint32_t off, uint32_t data) { struct usb_device_request req; uint32_t buf; usb_error_t err; SMSC_LOCK_ASSERT(sc, MA_OWNED); buf = htole32(data); req.bmRequestType = UT_WRITE_VENDOR_DEVICE; req.bRequest = SMSC_UR_WRITE_REG; USETW(req.wValue, 0); USETW(req.wIndex, off); USETW(req.wLength, 4); err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); if (err != 0) smsc_warn_printf(sc, "Failed to write register 0x%0x\n", off); return (err); } /** * smsc_wait_for_bits - Polls on a register value until bits are cleared * @sc: soft context * @reg: offset of the register * @bits: if the bits are clear the function returns * * LOCKING: * The device lock must be held before calling this function. * * RETURNS: * 0 on success, or a USB_ERR_?? error code on failure. */ static int smsc_wait_for_bits(struct smsc_softc *sc, uint32_t reg, uint32_t bits) { usb_ticks_t start_ticks; const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); uint32_t val; int err; SMSC_LOCK_ASSERT(sc, MA_OWNED); start_ticks = (usb_ticks_t)ticks; do { if ((err = smsc_read_reg(sc, reg, &val)) != 0) return (err); if (!(val & bits)) return (0); uether_pause(&sc->sc_ue, hz / 100); } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); return (USB_ERR_TIMEOUT); } /** * smsc_eeprom_read - Reads the attached EEPROM * @sc: soft context * @off: the eeprom address offset * @buf: stores the bytes * @buflen: the number of bytes to read * * Simply reads bytes from an attached eeprom. * * LOCKING: * The function takes and releases the device lock if it is not already held. * * RETURNS: * 0 on success, or a USB_ERR_?? error code on failure. */ static int smsc_eeprom_read(struct smsc_softc *sc, uint16_t off, uint8_t *buf, uint16_t buflen) { usb_ticks_t start_ticks; const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); int err; int locked; uint32_t val; uint16_t i; locked = mtx_owned(&sc->sc_mtx); if (!locked) SMSC_LOCK(sc); err = smsc_wait_for_bits(sc, SMSC_EEPROM_CMD, SMSC_EEPROM_CMD_BUSY); if (err != 0) { smsc_warn_printf(sc, "eeprom busy, failed to read data\n"); goto done; } /* start reading the bytes, one at a time */ for (i = 0; i < buflen; i++) { val = SMSC_EEPROM_CMD_BUSY | (SMSC_EEPROM_CMD_ADDR_MASK & (off + i)); if ((err = smsc_write_reg(sc, SMSC_EEPROM_CMD, val)) != 0) goto done; start_ticks = (usb_ticks_t)ticks; do { if ((err = smsc_read_reg(sc, SMSC_EEPROM_CMD, &val)) != 0) goto done; if (!(val & SMSC_EEPROM_CMD_BUSY) || (val & SMSC_EEPROM_CMD_TIMEOUT)) break; uether_pause(&sc->sc_ue, hz / 100); } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); if (val & (SMSC_EEPROM_CMD_BUSY | SMSC_EEPROM_CMD_TIMEOUT)) { smsc_warn_printf(sc, "eeprom command failed\n"); err = USB_ERR_IOERROR; break; } if ((err = smsc_read_reg(sc, SMSC_EEPROM_DATA, &val)) != 0) goto done; buf[i] = (val & 0xff); } done: if (!locked) SMSC_UNLOCK(sc); return (err); } /** * smsc_miibus_readreg - Reads a MII/MDIO register * @dev: usb ether device * @phy: the number of phy reading from * @reg: the register address * * Attempts to read a phy register over the MII bus. * * LOCKING: * Takes and releases the device mutex lock if not already held. * * RETURNS: * Returns the 16-bits read from the MII register, if this function fails 0 * is returned. */ static int smsc_miibus_readreg(device_t dev, int phy, int reg) { struct smsc_softc *sc = device_get_softc(dev); int locked; uint32_t addr; uint32_t val = 0; locked = mtx_owned(&sc->sc_mtx); if (!locked) SMSC_LOCK(sc); if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) { smsc_warn_printf(sc, "MII is busy\n"); goto done; } addr = (phy << 11) | (reg << 6) | SMSC_MII_READ; smsc_write_reg(sc, SMSC_MII_ADDR, addr); if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) smsc_warn_printf(sc, "MII read timeout\n"); smsc_read_reg(sc, SMSC_MII_DATA, &val); val = le32toh(val); done: if (!locked) SMSC_UNLOCK(sc); return (val & 0xFFFF); } /** * smsc_miibus_writereg - Writes a MII/MDIO register * @dev: usb ether device * @phy: the number of phy writing to * @reg: the register address * @val: the value to write * * Attempts to write a phy register over the MII bus. * * LOCKING: * Takes and releases the device mutex lock if not already held. * * RETURNS: * Always returns 0 regardless of success or failure. */ static int smsc_miibus_writereg(device_t dev, int phy, int reg, int val) { struct smsc_softc *sc = device_get_softc(dev); int locked; uint32_t addr; if (sc->sc_phyno != phy) return (0); locked = mtx_owned(&sc->sc_mtx); if (!locked) SMSC_LOCK(sc); if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) { smsc_warn_printf(sc, "MII is busy\n"); goto done; } val = htole32(val); smsc_write_reg(sc, SMSC_MII_DATA, val); addr = (phy << 11) | (reg << 6) | SMSC_MII_WRITE; smsc_write_reg(sc, SMSC_MII_ADDR, addr); if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) smsc_warn_printf(sc, "MII write timeout\n"); done: if (!locked) SMSC_UNLOCK(sc); return (0); } /** * smsc_miibus_statchg - Called to detect phy status change * @dev: usb ether device * * This function is called periodically by the system to poll for status * changes of the link. * * LOCKING: * Takes and releases the device mutex lock if not already held. */ static void smsc_miibus_statchg(device_t dev) { struct smsc_softc *sc = device_get_softc(dev); struct mii_data *mii = uether_getmii(&sc->sc_ue); struct ifnet *ifp; int locked; int err; uint32_t flow; uint32_t afc_cfg; locked = mtx_owned(&sc->sc_mtx); if (!locked) SMSC_LOCK(sc); ifp = uether_getifp(&sc->sc_ue); if (mii == NULL || ifp == NULL || (ifp->if_drv_flags & IFF_DRV_RUNNING) == 0) goto done; /* Use the MII status to determine link status */ sc->sc_flags &= ~SMSC_FLAG_LINK; if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) == (IFM_ACTIVE | IFM_AVALID)) { switch (IFM_SUBTYPE(mii->mii_media_active)) { case IFM_10_T: case IFM_100_TX: sc->sc_flags |= SMSC_FLAG_LINK; break; case IFM_1000_T: /* Gigabit ethernet not supported by chipset */ break; default: break; } } /* Lost link, do nothing. */ if ((sc->sc_flags & SMSC_FLAG_LINK) == 0) { smsc_dbg_printf(sc, "link flag not set\n"); goto done; } err = smsc_read_reg(sc, SMSC_AFC_CFG, &afc_cfg); if (err) { smsc_warn_printf(sc, "failed to read initial AFC_CFG, error %d\n", err); goto done; } /* Enable/disable full duplex operation and TX/RX pause */ if ((IFM_OPTIONS(mii->mii_media_active) & IFM_FDX) != 0) { smsc_dbg_printf(sc, "full duplex operation\n"); sc->sc_mac_csr &= ~SMSC_MAC_CSR_RCVOWN; sc->sc_mac_csr |= SMSC_MAC_CSR_FDPX; if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_RXPAUSE) != 0) flow = 0xffff0002; else flow = 0; if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_TXPAUSE) != 0) afc_cfg |= 0xf; else afc_cfg &= ~0xf; } else { smsc_dbg_printf(sc, "half duplex operation\n"); sc->sc_mac_csr &= ~SMSC_MAC_CSR_FDPX; sc->sc_mac_csr |= SMSC_MAC_CSR_RCVOWN; flow = 0; afc_cfg |= 0xf; } err = smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); err += smsc_write_reg(sc, SMSC_FLOW, flow); err += smsc_write_reg(sc, SMSC_AFC_CFG, afc_cfg); if (err) smsc_warn_printf(sc, "media change failed, error %d\n", err); done: if (!locked) SMSC_UNLOCK(sc); } /** * smsc_ifmedia_upd - Set media options * @ifp: interface pointer * * Basically boilerplate code that simply calls the mii functions to set the * media options. * * LOCKING: * The device lock must be held before this function is called. * * RETURNS: * Returns 0 on success or a negative error code. */ static int smsc_ifmedia_upd(struct ifnet *ifp) { struct smsc_softc *sc = ifp->if_softc; struct mii_data *mii = uether_getmii(&sc->sc_ue); int err; SMSC_LOCK_ASSERT(sc, MA_OWNED); if (mii->mii_instance) { struct mii_softc *miisc; LIST_FOREACH(miisc, &mii->mii_phys, mii_list) mii_phy_reset(miisc); } err = mii_mediachg(mii); return (err); } /** * smsc_ifmedia_sts - Report current media status * @ifp: inet interface pointer * @ifmr: interface media request * * Basically boilerplate code that simply calls the mii functions to get the * media status. * * LOCKING: * Internally takes and releases the device lock. */ static void smsc_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) { struct smsc_softc *sc = ifp->if_softc; struct mii_data *mii = uether_getmii(&sc->sc_ue); SMSC_LOCK(sc); mii_pollstat(mii); SMSC_UNLOCK(sc); ifmr->ifm_active = mii->mii_media_active; ifmr->ifm_status = mii->mii_media_status; } /** * smsc_hash - Calculate the hash of a mac address * @addr: The mac address to calculate the hash on * * This function is used when configuring a range of m'cast mac addresses to * filter on. The hash of the mac address is put in the device's mac hash * table. * * RETURNS: * Returns a value from 0-63 value which is the hash of the mac address. */ static inline uint32_t smsc_hash(uint8_t addr[ETHER_ADDR_LEN]) { return (ether_crc32_be(addr, ETHER_ADDR_LEN) >> 26) & 0x3f; } /** * smsc_setmulti - Setup multicast * @ue: usb ethernet device context * * Tells the device to either accept frames with a multicast mac address, a * select group of m'cast mac addresses or just the devices mac address. * * LOCKING: * Should be called with the SMSC lock held. */ static void smsc_setmulti(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); struct ifnet *ifp = uether_getifp(ue); struct ifmultiaddr *ifma; uint32_t hashtbl[2] = { 0, 0 }; uint32_t hash; SMSC_LOCK_ASSERT(sc, MA_OWNED); if (ifp->if_flags & (IFF_ALLMULTI | IFF_PROMISC)) { smsc_dbg_printf(sc, "receive all multicast enabled\n"); sc->sc_mac_csr |= SMSC_MAC_CSR_MCPAS; sc->sc_mac_csr &= ~SMSC_MAC_CSR_HPFILT; } else { /* Take the lock of the mac address list before hashing each of them */ if_maddr_rlock(ifp); if (!TAILQ_EMPTY(&ifp->if_multiaddrs)) { /* We are filtering on a set of address so calculate hashes of each * of the address and set the corresponding bits in the register. */ sc->sc_mac_csr |= SMSC_MAC_CSR_HPFILT; sc->sc_mac_csr &= ~(SMSC_MAC_CSR_PRMS | SMSC_MAC_CSR_MCPAS); TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) { if (ifma->ifma_addr->sa_family != AF_LINK) continue; hash = smsc_hash(LLADDR((struct sockaddr_dl *)ifma->ifma_addr)); hashtbl[hash >> 5] |= 1 << (hash & 0x1F); } } else { /* Only receive packets with destination set to our mac address */ sc->sc_mac_csr &= ~(SMSC_MAC_CSR_MCPAS | SMSC_MAC_CSR_HPFILT); } if_maddr_runlock(ifp); /* Debug */ if (sc->sc_mac_csr & SMSC_MAC_CSR_HPFILT) smsc_dbg_printf(sc, "receive select group of macs\n"); else smsc_dbg_printf(sc, "receive own packets only\n"); } /* Write the hash table and mac control registers */ smsc_write_reg(sc, SMSC_HASHH, hashtbl[1]); smsc_write_reg(sc, SMSC_HASHL, hashtbl[0]); smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); } /** * smsc_setpromisc - Enables/disables promiscuous mode * @ue: usb ethernet device context * * LOCKING: * Should be called with the SMSC lock held. */ static void smsc_setpromisc(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); struct ifnet *ifp = uether_getifp(ue); smsc_dbg_printf(sc, "promiscuous mode %sabled\n", (ifp->if_flags & IFF_PROMISC) ? "en" : "dis"); SMSC_LOCK_ASSERT(sc, MA_OWNED); if (ifp->if_flags & IFF_PROMISC) sc->sc_mac_csr |= SMSC_MAC_CSR_PRMS; else sc->sc_mac_csr &= ~SMSC_MAC_CSR_PRMS; smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); } /** * smsc_sethwcsum - Enable or disable H/W UDP and TCP checksumming * @sc: driver soft context * * LOCKING: * Should be called with the SMSC lock held. * * RETURNS: * Returns 0 on success or a negative error code. */ static int smsc_sethwcsum(struct smsc_softc *sc) { struct ifnet *ifp = uether_getifp(&sc->sc_ue); uint32_t val; int err; if (!ifp) return (-EIO); SMSC_LOCK_ASSERT(sc, MA_OWNED); err = smsc_read_reg(sc, SMSC_COE_CTRL, &val); if (err != 0) { smsc_warn_printf(sc, "failed to read SMSC_COE_CTRL (err=%d)\n", err); return (err); } /* Enable/disable the Rx checksum */ if ((ifp->if_capabilities & ifp->if_capenable) & IFCAP_RXCSUM) val |= SMSC_COE_CTRL_RX_EN; else val &= ~SMSC_COE_CTRL_RX_EN; /* Enable/disable the Tx checksum (currently not supported) */ if ((ifp->if_capabilities & ifp->if_capenable) & IFCAP_TXCSUM) val |= SMSC_COE_CTRL_TX_EN; else val &= ~SMSC_COE_CTRL_TX_EN; err = smsc_write_reg(sc, SMSC_COE_CTRL, val); if (err != 0) { smsc_warn_printf(sc, "failed to write SMSC_COE_CTRL (err=%d)\n", err); return (err); } return (0); } /** * smsc_setmacaddress - Sets the mac address in the device * @sc: driver soft context * @addr: pointer to array contain at least 6 bytes of the mac * * Writes the MAC address into the device, usually the MAC is programmed with * values from the EEPROM. * * LOCKING: * Should be called with the SMSC lock held. * * RETURNS: * Returns 0 on success or a negative error code. */ static int smsc_setmacaddress(struct smsc_softc *sc, const uint8_t *addr) { int err; uint32_t val; smsc_dbg_printf(sc, "setting mac address to %02x:%02x:%02x:%02x:%02x:%02x\n", addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); SMSC_LOCK_ASSERT(sc, MA_OWNED); val = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0]; if ((err = smsc_write_reg(sc, SMSC_MAC_ADDRL, val)) != 0) goto done; val = (addr[5] << 8) | addr[4]; err = smsc_write_reg(sc, SMSC_MAC_ADDRH, val); done: return (err); } /** * smsc_reset - Reset the SMSC chip * @sc: device soft context * * LOCKING: * Should be called with the SMSC lock held. */ static void smsc_reset(struct smsc_softc *sc) { struct usb_config_descriptor *cd; usb_error_t err; cd = usbd_get_config_descriptor(sc->sc_ue.ue_udev); err = usbd_req_set_config(sc->sc_ue.ue_udev, &sc->sc_mtx, cd->bConfigurationValue); if (err) smsc_warn_printf(sc, "reset failed (ignored)\n"); /* Wait a little while for the chip to get its brains in order. */ uether_pause(&sc->sc_ue, hz / 100); /* Reinitialize controller to achieve full reset. */ smsc_chip_init(sc); } /** * smsc_init - Initialises the LAN95xx chip * @ue: USB ether interface * * Called when the interface is brought up (i.e. ifconfig ue0 up), this * initialise the interface and the rx/tx pipes. * * LOCKING: * Should be called with the SMSC lock held. */ static void smsc_init(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); struct ifnet *ifp = uether_getifp(ue); SMSC_LOCK_ASSERT(sc, MA_OWNED); if ((ifp->if_drv_flags & IFF_DRV_RUNNING) != 0) return; /* Cancel pending I/O */ smsc_stop(ue); #if __FreeBSD_version <= 1000000 /* On earlier versions this was the first place we could tell the system * that we supported h/w csuming, however this is only called after the * the interface has been brought up - not ideal. */ if (!(ifp->if_capabilities & IFCAP_RXCSUM)) { ifp->if_capabilities |= IFCAP_RXCSUM; ifp->if_capenable |= IFCAP_RXCSUM; ifp->if_hwassist = 0; } /* TX checksuming is disabled for now ifp->if_capabilities |= IFCAP_TXCSUM; ifp->if_capenable |= IFCAP_TXCSUM; ifp->if_hwassist = CSUM_TCP | CSUM_UDP; */ #endif /* Reset the ethernet interface. */ smsc_reset(sc); /* Load the multicast filter. */ smsc_setmulti(ue); /* TCP/UDP checksum offload engines. */ smsc_sethwcsum(sc); usbd_xfer_set_stall(sc->sc_xfer[SMSC_BULK_DT_WR]); /* Indicate we are up and running. */ ifp->if_drv_flags |= IFF_DRV_RUNNING; /* Switch to selected media. */ smsc_ifmedia_upd(ifp); smsc_start(ue); } /** * smsc_bulk_read_callback - Read callback used to process the USB URB * @xfer: the USB transfer * @error: * * Reads the URB data which can contain one or more ethernet frames, the * frames are copyed into a mbuf and given to the system. * * LOCKING: * No locking required, doesn't access internal driver settings. */ static void smsc_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) { struct smsc_softc *sc = usbd_xfer_softc(xfer); struct usb_ether *ue = &sc->sc_ue; struct ifnet *ifp = uether_getifp(ue); struct mbuf *m; struct usb_page_cache *pc; uint32_t rxhdr; uint16_t pktlen; int off; int actlen; usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); smsc_dbg_printf(sc, "rx : actlen %d\n", actlen); switch (USB_GET_STATE(xfer)) { case USB_ST_TRANSFERRED: /* There is always a zero length frame after bringing the IF up */ if (actlen < (sizeof(rxhdr) + ETHER_CRC_LEN)) goto tr_setup; /* There maybe multiple packets in the USB frame, each will have a * header and each needs to have it's own mbuf allocated and populated * for it. */ pc = usbd_xfer_get_frame(xfer, 0); off = 0; while (off < actlen) { /* The frame header is always aligned on a 4 byte boundary */ off = ((off + 0x3) & ~0x3); usbd_copy_out(pc, off, &rxhdr, sizeof(rxhdr)); off += (sizeof(rxhdr) + ETHER_ALIGN); rxhdr = le32toh(rxhdr); pktlen = (uint16_t)SMSC_RX_STAT_FRM_LENGTH(rxhdr); smsc_dbg_printf(sc, "rx : rxhdr 0x%08x : pktlen %d : actlen %d : " "off %d\n", rxhdr, pktlen, actlen, off); if (rxhdr & SMSC_RX_STAT_ERROR) { smsc_dbg_printf(sc, "rx error (hdr 0x%08x)\n", rxhdr); ifp->if_ierrors++; if (rxhdr & SMSC_RX_STAT_COLLISION) ifp->if_collisions++; } else { /* Check if the ethernet frame is too big or too small */ if ((pktlen < ETHER_HDR_LEN) || (pktlen > (actlen - off))) goto tr_setup; /* Create a new mbuf to store the packet in */ m = uether_newbuf(); if (m == NULL) { smsc_warn_printf(sc, "failed to create new mbuf\n"); ifp->if_iqdrops++; goto tr_setup; } usbd_copy_out(pc, off, mtod(m, uint8_t *), pktlen); /* Check if RX TCP/UDP checksumming is being offloaded */ if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) { /* Remove the extra 2 bytes of the csum */ pktlen -= 2; /* The checksum appears to be simplistically calculated * over the udp/tcp header and data up to the end of the * eth frame. Which means if the eth frame is padded * the csum calculation is incorrectly performed over * the padding bytes as well. Therefore to be safe we * ignore the H/W csum on frames less than or equal to * 64 bytes. */ if (pktlen > ETHER_MIN_LEN) { /* Indicate the UDP/TCP csum has been calculated */ m->m_pkthdr.csum_flags |= CSUM_DATA_VALID; /* Copy the TCP/UDP checksum from the last 2 bytes * of the transfer and put in the csum_data field. */ usbd_copy_out(pc, (off + pktlen), &m->m_pkthdr.csum_data, 2); /* The data is copied in network order, but the * csum algorithm in the kernel expects it to be * in host network order. */ m->m_pkthdr.csum_data = ntohs(m->m_pkthdr.csum_data); smsc_dbg_printf(sc, "RX checksum offloaded (0x%04x)\n", m->m_pkthdr.csum_data); } /* Need to adjust the offset as well or we'll be off * by 2 because the csum is removed from the packet * length. */ off += 2; } /* Finally enqueue the mbuf on the receive queue */ /* Remove 4 trailing bytes */ if (pktlen < (4 + ETHER_HDR_LEN)) { m_freem(m); goto tr_setup; } uether_rxmbuf(ue, m, pktlen - 4); } /* Update the offset to move to the next potential packet */ off += pktlen; } /* FALLTHROUGH */ case USB_ST_SETUP: tr_setup: usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); usbd_transfer_submit(xfer); uether_rxflush(ue); return; default: if (error != USB_ERR_CANCELLED) { smsc_warn_printf(sc, "bulk read error, %s\n", usbd_errstr(error)); usbd_xfer_set_stall(xfer); goto tr_setup; } return; } } /** * smsc_bulk_write_callback - Write callback used to send ethernet frame(s) * @xfer: the USB transfer * @error: error code if the transfers is in an errored state * * The main write function that pulls ethernet frames off the queue and sends * them out. * * LOCKING: * */ static void smsc_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) { struct smsc_softc *sc = usbd_xfer_softc(xfer); struct ifnet *ifp = uether_getifp(&sc->sc_ue); struct usb_page_cache *pc; struct mbuf *m; uint32_t txhdr; uint32_t frm_len = 0; int nframes; switch (USB_GET_STATE(xfer)) { case USB_ST_TRANSFERRED: ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; /* FALLTHROUGH */ case USB_ST_SETUP: tr_setup: if ((sc->sc_flags & SMSC_FLAG_LINK) == 0 || (ifp->if_drv_flags & IFF_DRV_OACTIVE) != 0) { /* Don't send anything if there is no link or controller is busy. */ return; } for (nframes = 0; nframes < 16 && !IFQ_DRV_IS_EMPTY(&ifp->if_snd); nframes++) { IFQ_DRV_DEQUEUE(&ifp->if_snd, m); if (m == NULL) break; usbd_xfer_set_frame_offset(xfer, nframes * MCLBYTES, nframes); frm_len = 0; pc = usbd_xfer_get_frame(xfer, nframes); /* Each frame is prefixed with two 32-bit values describing the * length of the packet and buffer. */ txhdr = SMSC_TX_CTRL_0_BUF_SIZE(m->m_pkthdr.len) | SMSC_TX_CTRL_0_FIRST_SEG | SMSC_TX_CTRL_0_LAST_SEG; txhdr = htole32(txhdr); usbd_copy_in(pc, 0, &txhdr, sizeof(txhdr)); txhdr = SMSC_TX_CTRL_1_PKT_LENGTH(m->m_pkthdr.len); txhdr = htole32(txhdr); usbd_copy_in(pc, 4, &txhdr, sizeof(txhdr)); frm_len += 8; /* Next copy in the actual packet */ usbd_m_copy_in(pc, frm_len, m, 0, m->m_pkthdr.len); frm_len += m->m_pkthdr.len; ifp->if_opackets++; /* If there's a BPF listener, bounce a copy of this frame to him */ BPF_MTAP(ifp, m); m_freem(m); /* Set frame length. */ usbd_xfer_set_frame_len(xfer, nframes, frm_len); } if (nframes != 0) { usbd_xfer_set_frames(xfer, nframes); usbd_transfer_submit(xfer); ifp->if_drv_flags |= IFF_DRV_OACTIVE; } return; default: ifp->if_oerrors++; ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; if (error != USB_ERR_CANCELLED) { smsc_err_printf(sc, "usb error on tx: %s\n", usbd_errstr(error)); usbd_xfer_set_stall(xfer); goto tr_setup; } return; } } /** * smsc_tick - Called periodically to monitor the state of the LAN95xx chip * @ue: USB ether interface * * Simply calls the mii status functions to check the state of the link. * * LOCKING: * Should be called with the SMSC lock held. */ static void smsc_tick(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); struct mii_data *mii = uether_getmii(&sc->sc_ue); SMSC_LOCK_ASSERT(sc, MA_OWNED); mii_tick(mii); if ((sc->sc_flags & SMSC_FLAG_LINK) == 0) { smsc_miibus_statchg(ue->ue_dev); if ((sc->sc_flags & SMSC_FLAG_LINK) != 0) smsc_start(ue); } } /** * smsc_start - Starts communication with the LAN95xx chip * @ue: USB ether interface * * * */ static void smsc_start(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); /* * start the USB transfers, if not already started: */ usbd_transfer_start(sc->sc_xfer[SMSC_BULK_DT_RD]); usbd_transfer_start(sc->sc_xfer[SMSC_BULK_DT_WR]); } /** * smsc_stop - Stops communication with the LAN95xx chip * @ue: USB ether interface * * * */ static void smsc_stop(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); struct ifnet *ifp = uether_getifp(ue); SMSC_LOCK_ASSERT(sc, MA_OWNED); ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE); sc->sc_flags &= ~SMSC_FLAG_LINK; /* * stop all the transfers, if not already stopped: */ usbd_transfer_stop(sc->sc_xfer[SMSC_BULK_DT_WR]); usbd_transfer_stop(sc->sc_xfer[SMSC_BULK_DT_RD]); } /** * smsc_phy_init - Initialises the in-built SMSC phy * @sc: driver soft context * * Resets the PHY part of the chip and then initialises it to default * values. The 'link down' and 'auto-negotiation complete' interrupts * from the PHY are also enabled, however we don't monitor the interrupt * endpoints for the moment. * * RETURNS: * Returns 0 on success or EIO if failed to reset the PHY. */ static int smsc_phy_init(struct smsc_softc *sc) { int bmcr; usb_ticks_t start_ticks; const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); SMSC_LOCK_ASSERT(sc, MA_OWNED); /* Reset phy and wait for reset to complete */ smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, BMCR_RESET); start_ticks = ticks; do { uether_pause(&sc->sc_ue, hz / 100); bmcr = smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); } while ((bmcr & MII_BMCR) && ((ticks - start_ticks) < max_ticks)); if (((usb_ticks_t)(ticks - start_ticks)) >= max_ticks) { smsc_err_printf(sc, "PHY reset timed-out"); return (EIO); } smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_ANAR, ANAR_10 | ANAR_10_FD | ANAR_TX | ANAR_TX_FD | /* all modes */ ANAR_CSMA | ANAR_FC | ANAR_PAUSE_ASYM); /* Setup the phy to interrupt when the link goes down or autoneg completes */ smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, SMSC_PHY_INTR_STAT); smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, SMSC_PHY_INTR_MASK, (SMSC_PHY_INTR_ANEG_COMP | SMSC_PHY_INTR_LINK_DOWN)); /* Restart auto-negotation */ bmcr = smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); bmcr |= BMCR_STARTNEG; smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, bmcr); return (0); } /** * smsc_chip_init - Initialises the chip after power on * @sc: driver soft context * * This initialisation sequence is modelled on the procedure in the Linux * driver. * * RETURNS: * Returns 0 on success or an error code on failure. */ static int smsc_chip_init(struct smsc_softc *sc) { int err; int locked; uint32_t reg_val; int burst_cap; locked = mtx_owned(&sc->sc_mtx); if (!locked) SMSC_LOCK(sc); /* Enter H/W config mode */ smsc_write_reg(sc, SMSC_HW_CFG, SMSC_HW_CFG_LRST); if ((err = smsc_wait_for_bits(sc, SMSC_HW_CFG, SMSC_HW_CFG_LRST)) != 0) { smsc_warn_printf(sc, "timed-out waiting for reset to complete\n"); goto init_failed; } /* Reset the PHY */ smsc_write_reg(sc, SMSC_PM_CTRL, SMSC_PM_CTRL_PHY_RST); if ((err = smsc_wait_for_bits(sc, SMSC_PM_CTRL, SMSC_PM_CTRL_PHY_RST) != 0)) { smsc_warn_printf(sc, "timed-out waiting for phy reset to complete\n"); goto init_failed; } /* Set the mac address */ if ((err = smsc_setmacaddress(sc, sc->sc_ue.ue_eaddr)) != 0) { smsc_warn_printf(sc, "failed to set the MAC address\n"); goto init_failed; } /* Don't know what the HW_CFG_BIR bit is, but following the reset sequence * as used in the Linux driver. */ if ((err = smsc_read_reg(sc, SMSC_HW_CFG, ®_val)) != 0) { smsc_warn_printf(sc, "failed to read HW_CFG: %d\n", err); goto init_failed; } reg_val |= SMSC_HW_CFG_BIR; smsc_write_reg(sc, SMSC_HW_CFG, reg_val); /* There is a so called 'turbo mode' that the linux driver supports, it * seems to allow you to jam multiple frames per Rx transaction. By default * this driver supports that and therefore allows multiple frames per URB. * * The xfer buffer size needs to reflect this as well, therefore based on * the calculations in the Linux driver the RX bufsize is set to 18944, * bufsz = (16 * 1024 + 5 * 512) * * Burst capability is the number of URBs that can be in a burst of data/ * ethernet frames. */ if (usbd_get_speed(sc->sc_ue.ue_udev) == USB_SPEED_HIGH) burst_cap = 37; else burst_cap = 128; smsc_write_reg(sc, SMSC_BURST_CAP, burst_cap); /* Set the default bulk in delay (magic value from Linux driver) */ smsc_write_reg(sc, SMSC_BULK_IN_DLY, 0x00002000); /* * Initialise the RX interface */ if ((err = smsc_read_reg(sc, SMSC_HW_CFG, ®_val)) < 0) { smsc_warn_printf(sc, "failed to read HW_CFG: (err = %d)\n", err); goto init_failed; } /* Adjust the packet offset in the buffer (designed to try and align IP * header on 4 byte boundary) */ reg_val &= ~SMSC_HW_CFG_RXDOFF; reg_val |= (ETHER_ALIGN << 9) & SMSC_HW_CFG_RXDOFF; /* The following setings are used for 'turbo mode', a.k.a multiple frames * per Rx transaction (again info taken form Linux driver). */ reg_val |= (SMSC_HW_CFG_MEF | SMSC_HW_CFG_BCE); smsc_write_reg(sc, SMSC_HW_CFG, reg_val); /* Clear the status register ? */ smsc_write_reg(sc, SMSC_INTR_STATUS, 0xffffffff); /* Read and display the revision register */ if ((err = smsc_read_reg(sc, SMSC_ID_REV, &sc->sc_rev_id)) < 0) { smsc_warn_printf(sc, "failed to read ID_REV (err = %d)\n", err); goto init_failed; } device_printf(sc->sc_ue.ue_dev, "chip 0x%04lx, rev. %04lx\n", (sc->sc_rev_id & SMSC_ID_REV_CHIP_ID_MASK) >> 16, (sc->sc_rev_id & SMSC_ID_REV_CHIP_REV_MASK)); /* GPIO/LED setup */ reg_val = SMSC_LED_GPIO_CFG_SPD_LED | SMSC_LED_GPIO_CFG_LNK_LED | SMSC_LED_GPIO_CFG_FDX_LED; smsc_write_reg(sc, SMSC_LED_GPIO_CFG, reg_val); /* * Initialise the TX interface */ smsc_write_reg(sc, SMSC_FLOW, 0); smsc_write_reg(sc, SMSC_AFC_CFG, AFC_CFG_DEFAULT); /* Read the current MAC configuration */ if ((err = smsc_read_reg(sc, SMSC_MAC_CSR, &sc->sc_mac_csr)) < 0) { smsc_warn_printf(sc, "failed to read MAC_CSR (err=%d)\n", err); goto init_failed; } /* Vlan */ smsc_write_reg(sc, SMSC_VLAN1, (uint32_t)ETHERTYPE_VLAN); /* * Initialise the PHY */ if ((err = smsc_phy_init(sc)) != 0) goto init_failed; /* * Start TX */ sc->sc_mac_csr |= SMSC_MAC_CSR_TXEN; smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); smsc_write_reg(sc, SMSC_TX_CFG, SMSC_TX_CFG_ON); /* * Start RX */ sc->sc_mac_csr |= SMSC_MAC_CSR_RXEN; smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); if (!locked) SMSC_UNLOCK(sc); return (0); init_failed: if (!locked) SMSC_UNLOCK(sc); smsc_err_printf(sc, "smsc_chip_init failed (err=%d)\n", err); return (err); } /** * smsc_ioctl - ioctl function for the device * @ifp: interface pointer * @cmd: the ioctl command * @data: data passed in the ioctl call, typically a pointer to struct ifreq. * * The ioctl routine is overridden to detect change requests for the H/W * checksum capabilities. * * RETURNS: * 0 on success and an error code on failure. */ static int smsc_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data) { struct usb_ether *ue = ifp->if_softc; struct smsc_softc *sc; struct ifreq *ifr; int rc; int mask; int reinit; if (cmd == SIOCSIFCAP) { sc = uether_getsc(ue); ifr = (struct ifreq *)data; SMSC_LOCK(sc); rc = 0; reinit = 0; mask = ifr->ifr_reqcap ^ ifp->if_capenable; /* Modify the RX CSUM enable bits */ if ((mask & IFCAP_RXCSUM) != 0 && (ifp->if_capabilities & IFCAP_RXCSUM) != 0) { ifp->if_capenable ^= IFCAP_RXCSUM; if (ifp->if_drv_flags & IFF_DRV_RUNNING) { ifp->if_drv_flags &= ~IFF_DRV_RUNNING; reinit = 1; } } SMSC_UNLOCK(sc); if (reinit) #if __FreeBSD_version > 1000000 uether_init(ue); #else ifp->if_init(ue); #endif } else { rc = uether_ioctl(ifp, cmd, data); } return (rc); } #ifdef FDT /** * Get MAC address from FDT blob. Firmware or loader should fill * mac-address or local-mac-address property Returns 0 if MAC address * obtained, error code otherwise */ static int smsc_fdt_find_mac(unsigned char *mac) { phandle_t child, parent, root; int len; root = OF_finddevice("/"); len = 0; parent = root; /* Traverse through entire tree to find nodes usb ethernet nodes */ for (child = OF_child(parent); child != 0; child = OF_peer(child)) { /* Find a 'leaf'. Start the search from this node. */ while (OF_child(child)) { parent = child; child = OF_child(child); } if (fdt_is_compatible(child, "net,ethernet") && fdt_is_compatible(child, "usb,device")) { /* Check if there is property */ if ((len = OF_getproplen(child, "local-mac-address")) > 0) { if (len != ETHER_ADDR_LEN) return (EINVAL); OF_getprop(child, "local-mac-address", mac, ETHER_ADDR_LEN); return (0); } if ((len = OF_getproplen(child, "mac-address")) > 0) { if (len != ETHER_ADDR_LEN) return (EINVAL); OF_getprop(child, "mac-address", mac, ETHER_ADDR_LEN); return (0); } } if (OF_peer(child) == 0) { /* No more siblings. */ child = parent; parent = OF_parent(child); } } return (ENXIO); } #endif /** * smsc_attach_post - Called after the driver attached to the USB interface * @ue: the USB ethernet device * * This is where the chip is intialised for the first time. This is different * from the smsc_init() function in that that one is designed to setup the * H/W to match the UE settings and can be called after a reset. * * */ static void smsc_attach_post(struct usb_ether *ue) { struct smsc_softc *sc = uether_getsc(ue); uint32_t mac_h, mac_l; int err; smsc_dbg_printf(sc, "smsc_attach_post\n"); /* Setup some of the basics */ sc->sc_phyno = 1; /* Attempt to get the mac address, if an EEPROM is not attached this * will just return FF:FF:FF:FF:FF:FF, so in such cases we invent a MAC * address based on urandom. */ memset(sc->sc_ue.ue_eaddr, 0xff, ETHER_ADDR_LEN); /* Check if there is already a MAC address in the register */ if ((smsc_read_reg(sc, SMSC_MAC_ADDRL, &mac_l) == 0) && (smsc_read_reg(sc, SMSC_MAC_ADDRH, &mac_h) == 0)) { sc->sc_ue.ue_eaddr[5] = (uint8_t)((mac_h >> 8) & 0xff); sc->sc_ue.ue_eaddr[4] = (uint8_t)((mac_h) & 0xff); sc->sc_ue.ue_eaddr[3] = (uint8_t)((mac_l >> 24) & 0xff); sc->sc_ue.ue_eaddr[2] = (uint8_t)((mac_l >> 16) & 0xff); sc->sc_ue.ue_eaddr[1] = (uint8_t)((mac_l >> 8) & 0xff); sc->sc_ue.ue_eaddr[0] = (uint8_t)((mac_l) & 0xff); } /* MAC address is not set so try to read from EEPROM, if that fails generate * a random MAC address. */ if (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr)) { err = smsc_eeprom_read(sc, 0x01, sc->sc_ue.ue_eaddr, ETHER_ADDR_LEN); #ifdef FDT if ((err != 0) || (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr))) err = smsc_fdt_find_mac(sc->sc_ue.ue_eaddr); #endif if ((err != 0) || (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr))) { read_random(sc->sc_ue.ue_eaddr, ETHER_ADDR_LEN); sc->sc_ue.ue_eaddr[0] &= ~0x01; /* unicast */ sc->sc_ue.ue_eaddr[0] |= 0x02; /* locally administered */ } } /* Initialise the chip for the first time */ smsc_chip_init(sc); } /** * smsc_attach_post_sub - Called after the driver attached to the USB interface * @ue: the USB ethernet device * * Most of this is boilerplate code and copied from the base USB ethernet * driver. It has been overriden so that we can indicate to the system that * the chip supports H/W checksumming. * * RETURNS: * Returns 0 on success or a negative error code. */ #if __FreeBSD_version > 1000000 static int smsc_attach_post_sub(struct usb_ether *ue) { struct smsc_softc *sc; struct ifnet *ifp; int error; sc = uether_getsc(ue); ifp = ue->ue_ifp; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_start = uether_start; ifp->if_ioctl = smsc_ioctl; ifp->if_init = uether_init; IFQ_SET_MAXLEN(&ifp->if_snd, ifqmaxlen); ifp->if_snd.ifq_drv_maxlen = ifqmaxlen; IFQ_SET_READY(&ifp->if_snd); /* The chip supports TCP/UDP checksum offloading on TX and RX paths, however * currently only RX checksum is supported in the driver (see top of file). */ ifp->if_capabilities |= IFCAP_RXCSUM; ifp->if_hwassist = 0; /* TX checksuming is disabled (for now?) ifp->if_capabilities |= IFCAP_TXCSUM; ifp->if_capenable |= IFCAP_TXCSUM; ifp->if_hwassist = CSUM_TCP | CSUM_UDP; */ ifp->if_capenable = ifp->if_capabilities; mtx_lock(&Giant); error = mii_attach(ue->ue_dev, &ue->ue_miibus, ifp, uether_ifmedia_upd, ue->ue_methods->ue_mii_sts, BMSR_DEFCAPMASK, sc->sc_phyno, MII_OFFSET_ANY, 0); mtx_unlock(&Giant); return (error); } #endif /* __FreeBSD_version > 1000000 */ /** * smsc_probe - Probe the interface. * @dev: smsc device handle * * Checks if the device is a match for this driver. * * RETURNS: * Returns 0 on success or an error code on failure. */ static int smsc_probe(device_t dev) { struct usb_attach_arg *uaa = device_get_ivars(dev); if (uaa->usb_mode != USB_MODE_HOST) return (ENXIO); if (uaa->info.bConfigIndex != SMSC_CONFIG_INDEX) return (ENXIO); if (uaa->info.bIfaceIndex != SMSC_IFACE_IDX) return (ENXIO); return (usbd_lookup_id_by_uaa(smsc_devs, sizeof(smsc_devs), uaa)); } /** * smsc_attach - Attach the interface. * @dev: smsc device handle * * Allocate softc structures, do ifmedia setup and ethernet/BPF attach. * * RETURNS: * Returns 0 on success or a negative error code. */ static int smsc_attach(device_t dev) { struct usb_attach_arg *uaa = device_get_ivars(dev); struct smsc_softc *sc = device_get_softc(dev); struct usb_ether *ue = &sc->sc_ue; uint8_t iface_index; int err; sc->sc_flags = USB_GET_DRIVER_INFO(uaa); device_set_usb_desc(dev); mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF); /* Setup the endpoints for the SMSC LAN95xx device(s) */ iface_index = SMSC_IFACE_IDX; err = usbd_transfer_setup(uaa->device, &iface_index, sc->sc_xfer, smsc_config, SMSC_N_TRANSFER, sc, &sc->sc_mtx); if (err) { device_printf(dev, "error: allocating USB transfers failed\n"); goto detach; } ue->ue_sc = sc; ue->ue_dev = dev; ue->ue_udev = uaa->device; ue->ue_mtx = &sc->sc_mtx; ue->ue_methods = &smsc_ue_methods; err = uether_ifattach(ue); if (err) { device_printf(dev, "error: could not attach interface\n"); goto detach; } return (0); /* success */ detach: smsc_detach(dev); return (ENXIO); /* failure */ } /** * smsc_detach - Detach the interface. * @dev: smsc device handle * * RETURNS: * Returns 0. */ static int smsc_detach(device_t dev) { struct smsc_softc *sc = device_get_softc(dev); struct usb_ether *ue = &sc->sc_ue; usbd_transfer_unsetup(sc->sc_xfer, SMSC_N_TRANSFER); uether_ifdetach(ue); mtx_destroy(&sc->sc_mtx); return (0); } static device_method_t smsc_methods[] = { /* Device interface */ DEVMETHOD(device_probe, smsc_probe), DEVMETHOD(device_attach, smsc_attach), DEVMETHOD(device_detach, smsc_detach), /* bus interface */ DEVMETHOD(bus_print_child, bus_generic_print_child), DEVMETHOD(bus_driver_added, bus_generic_driver_added), /* MII interface */ DEVMETHOD(miibus_readreg, smsc_miibus_readreg), DEVMETHOD(miibus_writereg, smsc_miibus_writereg), DEVMETHOD(miibus_statchg, smsc_miibus_statchg), {0, 0} }; static driver_t smsc_driver = { .name = "smsc", .methods = smsc_methods, .size = sizeof(struct smsc_softc), }; static devclass_t smsc_devclass; DRIVER_MODULE(smsc, uhub, smsc_driver, smsc_devclass, NULL, 0); DRIVER_MODULE(miibus, smsc, miibus_driver, miibus_devclass, 0, 0); MODULE_DEPEND(smsc, uether, 1, 1, 1); MODULE_DEPEND(smsc, usb, 1, 1, 1); MODULE_DEPEND(smsc, ether, 1, 1, 1); MODULE_DEPEND(smsc, miibus, 1, 1, 1); MODULE_VERSION(smsc, 1);