/*- * SPDX-License-Identifier: BSD-2-Clause-FreeBSD * * Copyright (c) 2015 Bjoern A. Zeeb * Copyright (c) 2020 Denis Salopek * * This software was developed by SRI International and the University of * Cambridge Computer Laboratory under DARPA/AFRL contract FA8750-11-C-0249 * ("MRC2"), as part of the DARPA MRC research programme. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* $FreeBSD$ */ #define DEFAULT_ETHER_ADDRESS "\02SUME\00" #define SUME_ETH_DEVICE_NAME "sume" #define MAX_IFC_NAME_LEN 8 #define SUME_NPORTS 4 #define SUME_IOCTL_CMD_WRITE_REG (SIOCGPRIVATE_0) #define SUME_IOCTL_CMD_READ_REG (SIOCGPRIVATE_1) #define SUME_LOCK(adapter) mtx_lock(&adapter->lock); #define SUME_UNLOCK(adapter) mtx_unlock(&adapter->lock); /* Currently SUME only uses 2 fixed channels for all port traffic and regs. */ #define SUME_RIFFA_CHANNEL_DATA 0 #define SUME_RIFFA_CHANNEL_REG 1 #define SUME_RIFFA_CHANNELS 2 /* RIFFA constants. */ #define RIFFA_MAX_CHNLS 12 #define RIFFA_MAX_BUS_WIDTH_PARAM 4 #define RIFFA_SG_BUF_SIZE (4*1024) #define RIFFA_SG_ELEMS 200 /* RIFFA register offsets. */ #define RIFFA_RX_SG_LEN_REG_OFF 0x0 #define RIFFA_RX_SG_ADDR_LO_REG_OFF 0x1 #define RIFFA_RX_SG_ADDR_HI_REG_OFF 0x2 #define RIFFA_RX_LEN_REG_OFF 0x3 #define RIFFA_RX_OFFLAST_REG_OFF 0x4 #define RIFFA_TX_SG_LEN_REG_OFF 0x5 #define RIFFA_TX_SG_ADDR_LO_REG_OFF 0x6 #define RIFFA_TX_SG_ADDR_HI_REG_OFF 0x7 #define RIFFA_TX_LEN_REG_OFF 0x8 #define RIFFA_TX_OFFLAST_REG_OFF 0x9 #define RIFFA_INFO_REG_OFF 0xA #define RIFFA_IRQ_REG0_OFF 0xB #define RIFFA_IRQ_REG1_OFF 0xC #define RIFFA_RX_TNFR_LEN_REG_OFF 0xD #define RIFFA_TX_TNFR_LEN_REG_OFF 0xE #define RIFFA_CHNL_REG(c, o) ((c << 4) + o) /* * RIFFA state machine; * rather than using complex circular buffers for 1 transaction. */ #define SUME_RIFFA_CHAN_STATE_IDLE 0x01 #define SUME_RIFFA_CHAN_STATE_READY 0x02 #define SUME_RIFFA_CHAN_STATE_READ 0x04 #define SUME_RIFFA_CHAN_STATE_LEN 0x08 /* Accessor macros. */ #define SUME_OFFLAST ((0 << 1) | (1 & 0x01)) #define SUME_RIFFA_LAST(offlast) ((offlast) & 0x01) #define SUME_RIFFA_OFFSET(offlast) ((uint64_t)((offlast) >> 1) << 2) #define SUME_RIFFA_LEN(len) ((uint64_t)(len) << 2) #define SUME_RIFFA_LO_ADDR(addr) (addr & 0xFFFFFFFF) #define SUME_RIFFA_HI_ADDR(addr) ((addr >> 32) & 0xFFFFFFFF) /* Vector bits. */ #define SUME_MSI_RXQUE (1 << 0) #define SUME_MSI_RXBUF (1 << 1) #define SUME_MSI_RXDONE (1 << 2) #define SUME_MSI_TXBUF (1 << 3) #define SUME_MSI_TXDONE (1 << 4) /* Invalid vector. */ #define SUME_INVALID_VECT 0xc0000000 /* Module register data (packet counters, link status...) */ #define SUME_MOD0_REG_BASE 0x44040000 #define SUME_MOD_REG(port) (SUME_MOD0_REG_BASE + 0x10000 * port) #define SUME_RESET_OFFSET 0x8 #define SUME_PKTIN_OFFSET 0x18 #define SUME_PKTOUT_OFFSET 0x1c #define SUME_STATUS_OFFSET 0x48 #define SUME_RESET_ADDR(p) (SUME_MOD_REG(p) + SUME_RESET_OFFSET) #define SUME_STAT_RX_ADDR(p) (SUME_MOD_REG(p) + SUME_PKTIN_OFFSET) #define SUME_STAT_TX_ADDR(p) (SUME_MOD_REG(p) + SUME_PKTOUT_OFFSET) #define SUME_STATUS_ADDR(p) (SUME_MOD_REG(p) + SUME_STATUS_OFFSET) #define SUME_LINK_STATUS(val) ((val >> 12) & 0x1) /* Various bits and pieces. */ #define SUME_RIFFA_MAGIC 0xcafe #define SUME_MR_WRITE 0x1f #define SUME_MR_READ 0x00 #define SUME_INIT_RTAG -3 #define SUME_DPORT_MASK 0xaa #define SUME_MIN_PKT_SIZE (ETHER_MIN_LEN - ETHER_CRC_LEN) struct irq { uint32_t rid; struct resource *res; void *tag; } __aligned(CACHE_LINE_SIZE); struct nf_stats { uint64_t hw_rx_packets; uint64_t hw_tx_packets; uint64_t ifc_down_bytes; uint64_t ifc_down_packets; uint64_t rx_bytes; uint64_t rx_dropped; uint64_t rx_packets; uint64_t tx_bytes; uint64_t tx_dropped; uint64_t tx_packets; }; struct riffa_chnl_dir { uint32_t state; bus_dma_tag_t ch_tag; bus_dmamap_t ch_map; char *buf_addr; /* bouncebuf addresses+len. */ bus_addr_t buf_hw_addr; /* -- " -- mapped. */ uint32_t num_sg; uint32_t event; /* Used for modreg r/w */ uint32_t len; /* words */ uint32_t offlast; uint32_t recovery; uint32_t rtag; }; struct sume_ifreq { uint32_t addr; uint32_t val; }; struct nf_priv { struct sume_adapter *adapter; struct ifmedia media; struct nf_stats stats; uint32_t unit; uint32_t port; uint32_t link_up; }; struct sume_adapter { struct mtx lock; uint32_t running; uint32_t rid; struct riffa_chnl_dir **recv; struct riffa_chnl_dir **send; device_t dev; if_t ifp[SUME_NPORTS]; struct resource *bar0_addr; bus_space_tag_t bt; bus_space_handle_t bh; bus_size_t bar0_len; struct irq irq; struct callout timer; struct task stat_task; struct taskqueue *tq; uint64_t bytes_err; uint64_t packets_err; uint32_t last_ifc; uint32_t num_sg; uint32_t sg_buf_size; uint32_t sume_debug; uint32_t wd_counter; }; /* SUME metadata: * sport - not used for RX. For TX, set to 0x02, 0x08, 0x20, 0x80, depending on * the sending interface (nf0, nf1, nf2 or nf3). * dport - For RX, is set to 0x02, 0x08, 0x20, 0x80, depending on the receiving * interface (nf0, nf1, nf2 or nf3). For TX, set to 0x01, 0x04, 0x10, 0x40, * depending on the sending HW interface (nf0, nf1, nf2 or nf3). * plen - length of the send/receive packet data (in bytes) * magic - SUME hardcoded magic number which should be 0xcafe * t1, t1 - could be used for timestamping by SUME */ struct nf_metadata { uint16_t sport; uint16_t dport; uint16_t plen; uint16_t magic; uint32_t t1; uint32_t t2; }; /* Used for ioctl communication with the rwaxi program used to read/write SUME * internally defined register data. * addr - address of the SUME module register to read/write * val - value to write/read to/from the register * rtag - returned on read: transaction tag, for syncronization * optype - 0x1f when writing, 0x00 for reading */ struct nf_regop_data { uint32_t addr; uint32_t val; uint32_t rtag; uint32_t optype; }; /* Our bouncebuffer "descriptor". This holds our physical address (lower and * upper values) of the beginning of the DMA data to RX/TX. The len is number * of words to transmit. */ struct nf_bb_desc { uint32_t lower; uint32_t upper; uint32_t len; };